Yosemite Home Decor MCGH36S Use and Care Manual
Contents
1. to ensure that they do not play with the appliance L The air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels M The minimum distance between the supporting surface for the cooking vessels on the hob and the lowest part of the range hood shall be at least 65cm The instructions for installation of the gas hob specify a greater distance has to be taken into account if requirement stated O Regulation concerning the discharge of air has to be fulfilled INSTALLATION INSTRUCTIONS Assembly and electrical connections must be carried out by specialized personnel Electric Connection The appliance has been manufactured as class I therefore earth cable is necessary The connection to the mains 1s carried out as follows Whi If the plug is not provided connect the electrical load as indicated on the description label When a plug is provided the cooker hood must be installed in order that the plug is easy to access An omnipolar switch with a minimum aperture of 3mm between contacts in line with the electrical load and local standards must be placed between the appliance and the network in the case of direct connection to the electrical network The minimum distance between the support surfaces of the cooking pots on the cooker top and the lowest part of the cooker hood must be at least 65 cm If a connection tube composed of two parts 1s used the upper part mu2. USE AND CARE GUIDE WALL MOUNTED HOOD Fig 4 Fig 5 A A Co 3 S G OFF C w V gt T D E A B C D Fig 8 Fig 9 24 m T Ce f O 1 A B B C D E Fig 10 Fig 11 T A B C D E A B C D Fig 12 Fig 13 Hom 8 88 fA D E F G Fig 14 1 T B C D E A B C D E Fig 15 Fig 16 0 OFF LAMP OFF LAMP T MODE MODE TIME TIMER HIGH SPEED Fig 17 Fig 18 GENERAL Carefully read the following important information regarding installation safety and maintenance Keep this information booklet accessible for further consultations The appliance has been designed for use in the ducting version air exhaust to the outside Fig 1B filtering version air circulation on the inside Fig 1A or with external motor Fig 1C SAFETY PRECAUTION 1 Please take note that when the cooker hood is operating simultaneously with an open fireplace or burner that depend on the air in the environment the cooker hood may removes the air from the environment which a burner or fireplace need for combustion The negative pressure in the environment must not exceed 4Pa 4x10 5 bar Provide adequate ventilation in the environment for a safe operation of the cooker hood Follow the local laws appl
3. ave to dry The filters may also be washed in the dishwasher Please take note that the aluminum panels may alter in color after several washes The active carbon filters purify the air that 1s replaced in the environment The filters are not washable or reuseable and must be replaced at maximum every four months The saturation of the active carbon filter depends on the frequency of use of the appliance also by the type of cooking and the regularity of cleaning on the anti grease filters Fig 6 To remove the charcoal filters place our hand on one filter at a time and turn it toward the front part The charcoal filter can now be removed Always ensure to replace both filters at the same time Clean the fan and other surfaces of the cooker hood regularly using a cloth moistened with denatured alcohol or non abrasive liquid detergent The illumination installation 1s designed for use during cooking and not for prolonged general illumination of the environment Prolonged use of the illumination installation notably reduces the duration of the bulb Use a one edged screwdriver or any other appropriate tool to lift and remove the overhead light fixture Replace the damaged lamp Use only halogen lamps as the original specification avoiding contact with hands Return the light fixture to its position snap fastening Fig 7 How to replace the charcoal filters 1 Push the right middle corner on the glass of the decoration door F
4. cel the alarm set press the key F for 3 seconds Press key G light will on and symbol 22 display on the digital screen and press key G again to turn off the light FUNCTION KEYS Fig 15 A Timer automatic shut off B Speed 1 adjust switch off C digital display screen showing timer and speed D Speed 3 adjust switch off E Light When key A is being pressed digital display screen will show 15 minutes for timer whereas the minutes can be adjusted by pressing or on key B and D When the first speed 1s on pressing key A once to switch off the digital display will shows 00 on the screen When key B is being pressed it shows FI on the digital display screen at the same time first speed 1s on By pressing key B again to switch off the digital display will show 00 on the screen When key D is being pressed it shows F3 on the digital display screen at the same time the third speed 1s on By pressing key D again to switch off the digital display will show 00 on the screen The second speed F2 and Turbo speed F4 can be adjusted by pressing key B or D When key E 15 being pressed the light will on by pressing key E again is to switch off the light If the motor and light are operating together or only the motor is working pressing key A automatic switch off timer mode will get on In other word the unit will delay 15 minutes to turn off the motor and the light To press key B or key D 1s to a
5. dication light will flash on each function key button To on the light press key E To off the light press key E again B FUNCTION KEYS Fig 11 A Automatic Stop Timer 15 minutes B Speed 1 Control C Speed 2 Control D Speed 4 Light By pressing key B C or D individually the speed for each key will be the same as above table At the same time indicated light will flash on the each function key buttons To stop the speed function press key A If Speed 3 is required press key C adjust At Speed 3 program both key B and key C indication light will flash on each function key button To on the light press key E To off the light press key E again When the appliance and light are ON together or separately press key A the Automatic Stop Timer will start the 15 minutes count down Indication light on the key A button will flash for the duration To stop the Automatic Stop Timer Function before 15 minutes time frame press key A again B FUNCTION KEYS Fig 12 Fig 17 Infrared Remote Control B Off C Speed 1 Control D Speed 2 Control E Light By pressing key C or D individually the speed for each key will be the same as above table At the same time indication light will flash on the each function key button To stop the speed function press key B If Speed 3 is required press key D and adjust At Speed 3 program both key C and key D indication light wi
6. djust the time whereas to press key A again is to stop the timer B FUNCTION KEYS Fig 16 Fig 18 Infrared Remote Control B Timer Automatic Shut Off C Digital Display Timer Speed D Speed F1 Cycle Control Adjustment Off E Light When key B is pressed digital display screen will display 15 minutes For cycle control adjustment and Speed F1 press key D To stop the operation press key B again the digital display screen will show OO If using remote control press OFF button When key D is being pressed the digital display screen will show F1 and speed 1 will ON To stop F1 function press key D until the digital display screen shown OO The F2 F3 Or F4 Turbo function can be adjusted thru key D For ON OFF light press key E When the appliance and light are ON together or separately press key B the Automatic Stop Timer will start the 15 minutes count down Key D can also be used to extend the time of Automatic Stop Timer To stop the Automatic Stop Timer Function before 15 minutes time frame press key B again Troubleshooting Hood doesn t work Electric supply Check whether the plug connected turned on filters clogged when dry clogged without air flow while motor stop safety device activated ventilated working The hood is being The hood must be least 65cm of installed too near to the distance from the stove cooking stove install filters 1 must be installed installed oil cup saturated W
7. he digital display it reminds the user to clean the filters After the filter has been cleaned assemble back Press key A till the light 1s off and the unit is back to setting function again 00020000 m When pressing key A for 3 seconds the clock 222521 the digital display will flash press key A to switch the mode function to set hours and minutes and then press key C or E to set the correct time The Clock s system 1s 24 hours When the motor is on press key B the light will on At the same time C 0 15 will flash on the digital display and to press key B to switch the function mode to set hours and minutes To set the time to automatically shut off key C or E has to be pressed Press key B for 3 seconds to stop the delay timer H1 2 Press key or to start the first speed and it shows on the digital display and to press key C once again to turn off To run the 24 3 and Turbo speed press Key E If the Turbo speed is on press key E once again to turn off and by pressing key C the speed can be adjusted down from 3 24 and 1 On the special function setting mode after the speed TURBO runs for 2 minutes it will automatically switch to 3 speed Press key light will flash and it shows 4 L i flashing on the digital display to press key F again to switch to set hours and minutes mode To set the alarm press key C or E To stop the alarm press the key F And to can
8. hirring sound Fan blade problem THE MANUFACTURORY DECLINES ALL RESPONSIBILITY FOR EVENTUAL DAMAGES CAUSED BY BREACHING THE ABOVE WARNINGS Correct Disposal of this product This marking indicates that this product should not be disposed with other household wastes throughout the EU To prevent possible harm to the environment or human health from uncontrolled waste disposal recycle it responsibly to promote the sustainable reuse of material resources To return your used device please use the return and collection systems or contact the retailer where the product was purchased They can take this product for environmental safe recycling Warranty Information The manufacturer provides warranty in accordance with the legislation of the customer s own country of residence with a minimum of 1 year Germany 2 years starting from the date on which the appliance is sold to the end user The warranty only covers defects in material or workmanship The repairs under warranty may only be carried out by an authorized service centre When making a claim under the warranty the original bill of purchase with purchase date must be submitted The warranty will not apply in cases of Normal wear and tear Incorrect use e g overloading of the appliance use of non approved accessories Use of force damage caused by external influences Damage caused by non observance of the user manual e g connection to an unsuitable mains supp
9. icable for external air evacuation Before connecting the model to the electricity network control the data plate positioned inside the appliance to ascertain that the voltage and power correspond to the network and the socket is suitable If in doubt please ask qualified electrician for help 2 WARNING In certain circumstances electrical appliances may be a danger hazard A Do not check the status of the filters while the cooker hood 15 operating B Do not touch bulbs or adjacent areas after prolonged use of the lighting installation C Flambe cooking is prohibited underneath the cooker hood D Avoid free flame as it is damaging the filters and can cause fire hazard E Constantly check food frying the overheated oil may become a fire hazard F Disconnect the electrical plug prior to any maintenance G There shall be adequate ventilation in the room when the range hood is operating H There is a risk of fire if cleaning is not carried out in accordance with the instructions I If the supply cord is damaged it must be replaced by the manufacturer or its service agent or a similarly qualified person J This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety K Children should be supervised
10. ig 12 the decoration door will open Fig 13 2 Take out the aluminum filter Fig 14 3 Push the clips on the charcoal filters and then pull back then the charcoal filters can be taken down Fig 15 Fig 1 mm Fig 2 Fig 3 Fig 4 e FUNCTION KEYS Fig 8 FUNCTION KEYS Fig 9 A OFF A TIMER 15 MINUTES B SPEED I OFF B SPEED I C SPEED II OFF C SPEED II D SPEED III OFF D SPEED III E LIGHT E LIGHT f your appliance does not have the INTENSIVE speed function press key A for two seconds and it will be activated for 15 minutes after which it will return to the previously set speed If the function program of the unit is active the LED will flash By pressing any key except the key for the light the hood will return immediately to its normal functioning The automatic stop timer mode delays stopping operation of the hood the mode will continue functioning for 15 minutes at the operating speed set at the time this function is activated B FUNCTION KEYS Fig 10 OFF B SPEED 1 Control C SPEED 2 Control D SPEED 4 E LIGHT By pressing key C or D individually the speed for each key will be the same as above table At the same time indicated light will flash on the each function key button To stop the speed function press key A If Speed 3 is required press key C adjust At Speed 3 program both key B and key C in
11. ll flash on each function key button To on the light press key E To off the light press key E again B FUNCTION KEYS Fig 13 Fig 18 nfrared Remote Control B Automatic Stop Timer 15minutes C Speed 1 Control D Speed 2 Control E Light By pressing key C or D individually the speed for each key will be the same as above table At the same time indicated light will flash on the each function key buttons To stop the speed function press key If using Remote Control just press the OFF button If Speed is required press key D and adjust At Speed 3 program both key C and key D indication light will flash on each function key button If Speed 4 function is available when opeed 4 function is ON key C and D indication light will flash If using Remote Control press the t 5 key To on the light press key E To off the light press key E again When the appliance and light are ON together or separately press key A the Automatic Stop Timer will start the 15 minutes count down Indication light on the key A button will flash for the duration To stop the Automatic Stop Timer Function before 15 minutes time frame press key A again e FUNCTION KEYS Fig 14 A Filtering system Set clock B Delay Timer C Speed S1 adjust off D Digital display E Speed 51 adjust off F Alarm G Light When the Key is flashing at the same time is flashing on t
12. ly or non compliance with the installation instructions Partially or completely dismantled appliances
13. nnect the flange C to the air exhaust hole using a connection pipe Fig 4 To transform the hood from a ducting version into a filtering version ask your dealer for the charcoal filters and please follow the installation instructions FILTERING VERSION Install the hood and the two flues as described in the paragraph for installation of the hood in ducting version To assemble the filtering flue refers to the instructions contained in the kit If the kit 1s not provided please order it from your dealer The charcoal filters must be fitted in the ducting unit located inside the hood USE AND MAINTENANCE t is recommended to operate the appliance prior to cooking It is recommended to leave the appliance 1n operation for 15 minutes after cooking is terminated in order to completely eliminate cooking vapors and odours The proper function of the cooker hood 1s conditioned by the regularity of the maintenance operations in particular the active carbon filter The anti grease filters capture the grease particles suspended in the air and are therefore subject to clogging according to the frequency of the use of the appliance In order to prevent fire hazard it 1s recommendable to clean the filter at a maximum of 2 months by carrying out the following instructions Remove the filters from the cooker hood and wash them in a solution of water and neutral liquid detergent leaving to soak Rinse thoroughly with warm water and le
14. st be placed outside the lower part Do not connect the cooker hood exhaust to the same conductor used to circulate hot air or for evacuating fumes from other appliances generated by other than an electrical source Before proceeding with the assembly operations remove the anti grease filter s Fig 5 so that the unit is easier to handle In the case of assembly the appliance 1n the suction version prepare the hole for evacuation of the air FIXING TO THE WALL Drill the holes A respecting to the distances indicated Fig 2 Fix the appliance to the wall and align it in horizontal position to the wall units When the appliance has been adjusted fix the hood using the screws A For the various installations use screws and screw anchors suited to the type of wall e g reinforced concrete plasterboard etc If the screws and screw anchors are provided with the product kindly check the screws are suitable for the type of wall in which the hood 15 to be fixed FIXING THE DECORATIVE TELESCOPIC FLUE Arrange the electrical power supply within the dimensions of the decorative flue If your appliance 1s to be installed in the ducting version or in the version with external motor prepare the air exhaust opening Adjust the width of the support bracket of the upper flue Fig 3 Then fix it to the ceiling using the screws A Fig 2 make sure that it 1s in line with your hood and respecting the distance from the ceiling indicated in Fig 2 Co
Download Pdf Manuals
Related Search