Yosemite Home Decor BWRD36B Use and Care Manual
Contents
1. INSTALLATION GUIDE Read all installations beforeinstalling this appli IMPORTANT SAFETY NOTIC WARNING The installation in this manual is intended for qualified installers service techinicans or persons with similar qualified background Do not attempt to install this appliance yourself Injury couldresault from installing the unit due to lack of approriate electrical and technical background All electrical wiring must be properly installed insulated and grounded Overly accumulated greasein old duct work should be cleaned out or duct work should be replaced if necessary to avoid the possibility of a grease fire Check all joints on duct work to insure properconnection and all joints should be properly taped This appliance is marked according to the European directive 2002 96 EC on Waste Electrical and Electronic Equipment WEEE By ensuring this product is disposed of correcly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product The symbol on the product indicates that this product may not be treated as household waste Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment Disposal must be carried out in accordance with local environmental regulations for waste disposal For more detailed information about2. Regular service increases the output of your absorber plate Do not neglect to clean the filter regularly every 2 months The devices opens by moving the filter buttons the arrow as shows picture 7 the filter that is not cleaned regularly is dangerous and cause fire Filter cleaning or replacement In order to replace the filter you have to 1 open the device by moving the filter buttons the arrow as shows picture 2 abstract the wires that hold the filter Now you are able to change or clean the filter according to the type of filter you have used 1 Acrylic filter This filter has to be cleaned with a lukewarm later on a regular basis and every 4weeks maximum 2 metallic filter On normal use of the device every 30 days the filters must be washed in a washing machine or by hands with lukewarm water Before putting the filter to place they have to be dry Lamp replacement During lamp replacment procedure the absorber plate must be off The replacement of the lamps is made if you open the device by moving the filter buttons as the arrow shos picture7 Since the replacement of the lamps has take place there is the nothing more to do than placing the filter once again on the absorber plate by moving the filter buttons as the arrow shos picture 7 The replacement of the lamps also takes place by gently removing the plastic covers of the lamps The covers extraction must be carefully in order to avoid any
3. breaking danger see piture 8 The above instructions are respective to the 7 12 paragraph of the modes E A OT EN 60 335 1 AND EN 60 335 2 31 power devices and similar uses safety In case the absorber plate has two exits covered should remain the one that has not been used with the cover that is within the device 105mm Min600mm Max800mm
4. o not us spiral aluminum pipe as it lessens the function the brachium see picture has to be in position The extracted air must not be abducted to a chimney that is used for the extraction of fumes from the devices using gas or other fuel The norms that apply6 on the abduction of the extracted air must be followed See piture 3 Make sure that the voltage of power network agrees with the one that is writer on the type board of the absorber plate The connection to power must take place only by an authorized installation power technican The power line of the absorer plate must include a bipolar switch with contact separation distance over or equal to 3mm The device must be able to disconnect from the power supply In order for the absorber plate to function effectively you have to switch ton form the moment you switch on the cook burners After you finish the cooking you wait another 10 mins before switching the absorber plate off During cooking leave a door that is incontact with the rest inner part of the house half open Do not leave a window of an exit kitchen door open as it causes drafts that drift fumes away from the absorber plate has a contact button with two independent controls or pressure modulation on the contact button switch is made as following see picture 6 Power highspeed The device is washed by a lukewarm lather and a sponge well strained
5. treatment recovery and recycling of this product please contact your local city office your household waste disposal service or the shop where you purchased the product Installationg The right position of the absorber plate should be 60cm above the level of your electrical cook bumers or 80cm see piture 4 and 5 if there are gas bumers The absorber plate shouldbe used either for the odor extraction outwards or for air filtering and recyclingwithin the same space The installation must take place accordingly The recycling solution is advisable when there is no potential of pipe installation outside Put two lamps 40W in the lampholders Do not use lamps of power more than 40W as they cause local overheating In order to avoid possible noises from shocks we suggest you put a foam rubber tape on the back side between the absorber plate and the wall or the upper side between the absorber plate and the closet in relation to how you set your absorber plate Air extraction outwards The absorber plate must be connedted to the pipe of 120mm diameter on its upper spot The connetion to the pipe is made with the plastic groove you will find within the device The groove buttons up on the upper part of the absorber plate The long pipage and the multiple curvers must be avoided The horizontal parts must have a slight inclination to the multiple curves must be avoided The horizontal parts must have a slight inclination to the exit D
Download Pdf Manuals
Related Search