Vinotemp International VT-28-2Z-SSDST Use and Care Manual
Contents
1. SERVICE amp IMPORTANT NOTICE Upon receipt and inspection of unit the supply cord must be replaced if it is damaged Contact our customer service at 1 800 777 8466 or info vinotemp com The manufacturer has a policy of continuous improvement on its products and reserves the right to change materials and specifications without notice WARNING Please do not place the unit within reach of children For adult use only Contact info vinotemp com with any questions or visit www vinotemp com Cun 17621 S Susana Road Rancho Dominguez CA 90221 www vinotemp com Vinotemp is a registered trademark of Vinotemp International All products features and services are subject to change without notice We cannot guarantee the accuracy of the contents of this document We disclaim liability for errors omissions or future changes 2015 Vinotemp International All rights reserved gs bi A PROUD HERITAGE OF EXPERIENCE amp QUALITY A A A hj y Jj Wy LO A IRA WINE COOLER VT 28 2Z SSDST 28 BOTTLES OWNER S MANUAL WWW VINOTEMP COM TERMS OF SALE AND WARRANTY Vinotemp International Corp Seller and the person or entity that acquires these goods from Seller Purchaser hereby fully agrees to the following terms and conditions of the sale Shipping fees are the responsibility of the Purchaser whether freight prepaid or freight collect Seller assumes no responsibi2. e In some instances this is normal The light may flash when the automatic defrost function starts to work e Set temperature is higher than inner temperature Adjust temperature to resolve Display shows EL or e The air temperature sensor in the corresponding temperature zone has EH failed 17621 South Susana Road Rancho Dominguez California 90221 info vinotemp com DEFROSTING e The unit defrosts automatically e The evaporator behind the rear wall of the unit defrosts automatically The condensate collects in the drainage channel behind the rear wall ofthe unit and flows through the drainage hole into the drip tray by the compressor where it evaporates POWER FAILURE Most power failures are corrected within a few hours and should not affect the temperature of your appliance If the power is off for an extended period of time proper steps should be taken to protect your contents INACTIVITY If the unit will not be used for a period of less than three weeks leave the cooler operating If the period of inactivity is several months remove all items and turn the unit off Clean and dry the interior thoroughly Leave the door open slightly to prevent any possible moisture build up MOVING YOUR WINE COOLER Before moving your wine cooler first be sure to remove all items from the cooler e Securely tape down any loose items such as shelves inside the unit e Turn the adjustable leg up
3. any damages caused by the goods eighteen percent 18 annual rate Purchaser assumes and must immediately pay any credit card arbitration fees which the credit card companies charge during a dispute Any disputes not resolved within 30 days from the invoice date will be reported to credit reporting agencies LIMITED WARRANTY Seller warrants that the goods will be free of defects in materials and workmanship as follows Furniture style wood wine cabinets made in the U S all cooling unit parts for a period of 5 five years cabinetry and labor uninstalled for a period of 12 twelve months Metal cabinet wine units parts and labor for cooling system and cabinetry for a period of 12 twelve months For Designer Series units parts and labor for a period of 12 twelve months from date of sale compressor parts 5 years Thermoelectric Units 90 ninety days including Wine Coolers Beer Dispensers Humidor Portofino Wood Cellars and Refrigerators Wine Mate Split and Ducted Systems and other installed products and parts only for 1 year no labor Other Wine Mate Cooling Systems are 5 years parts 1 year labor Wine Accessories Racking Systems and Other items are not warranted There is no warranty on parts purchased separately If a purchaser claims a product is defective they must obtain a letter from a qualified refrigeration technician at the customers cost to verify that the unit was installed properly with proper ventilatio
4. E supplied For personal safety this appliance must be properly grounded Used to raise warm the set temperature by 1 C or 1 F e The cord should be secured behind the unit and not left exposed or dangling to prevent DOWN V accidental injury Used to lower cool the set temperature by 1 C or 1 F e A standard electrical supply 115V AC only 60Hz 15A properly grounded in accordance Fan with the National Electrical Code and local codes and ordinances is required FFC Selector e Never unplug the unit by pulling the power cord To disconnect the appliance always grip the Select the temperature display setting in Fahrenheit or Celsius degree To change the temperature plug firmly and pull straight out from the wall outlet When moving the unit be careful not to from Fahrenheit to Celsius or from Celsius to Fahrenheit touch and hold 9 mark for 5 seconds damage the power cord e The unit should always be plugged into its own individual electrical outlet with a voltage rating TEMPERATURE ZONES that matches the rating label on the unit The wine cooler has two temperature zones with a temperature range of 40 72 F The recommended CIRCUIT temperature setting for each zone is Extension Cord GROUNDING M e Lower Zone y between 55 72 F Ideal for red and white wines CAUTION It is strongly recommended that you do not use an adapter Be e Upper Zone between 40 55 F Ideal for sparkling and white wines or an extension cord with this un
5. Seller makes no oral representations of any kind These Terms and Conditions can only be modified in writing signed by both Purchaser and Seller YOUR WINE CELLAR This unit can be used for storage and or service The unit has a glass door and soft interior light to elegantly display your wine SERVING WINES Storing wines at the proper temperature is important To preserve them as long as possible wine should be stored at approximately 55 Fahrenheit However the chart below suggests the optimal drinking temperature for the different styles of wine C SE Wine Style i Light Bodied Red Wines Full Zur Alle Aue 7 Non Vintage Sparkling 17621 South Susana Road Rancho Dominguez California 90221 info vinotemp com General Operating Instructions Remove all external and internal packaging from your appliance Be sure that all parts have been included before discarding any packaging materials You may want to keep the box and packing materials for use at a later dete Upon receipt and inspection of unit the supply cord must be replaced if it is damaged Contact our customer service at 1 800 777 8466 or info vinotemp com Let the unit rest UNPLUGGED for 24 hours once you have it placed in your home READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE Save these instuctions To register your product visit http www vinotemp com Warranty aspx Register your warranty within 10 days of receivi
6. at or moisture or in direct sunlight Do NOT install the unit in a location with an ambient temperature that will fall below 60 F e For built in installation leave a Y 6 35mm space on each side and at the top of the wine cooler to ensure proper air circulation to cool the compressor and condenser Also be sure to not obstruct the front exhaust vent with any objects as this may affect the unit from performing properly e For freestanding installation 6 of space at the back 10 12 of space on each side and unlimited clearance at the top of the wine cooler are suggested to ensure proper air circulation to cool the compressor and condenser Do not place underneath a table counter top or anything of the sort as this will not allow for proper air circulation e Place the wine cooler on a level surface strong enough to support it when it is fully loaded To level the wine cooler adjust the front leveling legs at the bottom of the wine cooler e For best performance it is recommended that you install the appliance in a location with an ambient temperature between 72 78 F If the ambient temperature is above or below recommended temperatures the performance of the unit may be affected e t is recommended that you do not install the appliance near an oven radiator or other heating source Direct sunlight may affect the acrylic coating and heat sources may increase electrical consumption Don t install in a location where the temperatu
7. designed to be built in fully recessed or freestanding e Do not use this appliance for other than its intended purpose For indoor household use only e Do not operate the unit with wet hands while standing on a wet surface or while standing in water Do not use solvent based cleaning agents or abrasives on the interior of the cooler These cleaners may damage or discolor the interior Keep fingers out of pinch point areas and be careful when closing doors if children are around e This appliance is designed for storing and cooling wines Do not store perishable food or medical products within the unit e When disposing of refrigerated appliances special handling is often required It is the consumer s responsibility to comply with federal and local regulations when disposing of this product e WARNING Risk of child entrapment and suffocation Before you throw away this or an old unit take off the door Leave the shelves in place so that children may not easily climb inside WWW VINOTEMP COM STORING WINE While bottles may vary in size and dimension approximately 28 RSS traditional Bordeaux 750ml bottles can be stored in your wine cooler N ee You can place 15 standard bottles in the upper zone with 5 bottles on each shelf and 13 standard bottles in the lower zone with 5 bottles on each full size shelf and 3 bottles on each half size shelf 5 Bottle Arrangement Bottle capacities are approximate maximums when storing
8. eyond the Limited Warranty described above Warranty and liability are non transferable The implied warranties of merchantability and of fitness for a particular purpose are hereby expressly disclaimed Some states do not allow the exclusion of incidental or consequential damages or a waiver of the implied warranties of fitness and or merchantability so the above limitations may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state Seller disclaims any indemnification for claims of infringement of any intellectual property of protectable nature In the event of any dispute between Seller and Purchaser arising out of or relating to these terms and conditions or to the goods sold generally Purchaser must first file a written claim with Seller within ten days of the occurrence giving rise to the claim and wait an additional thirty days for a response before initiating any legal action The sale and all terms are subject to California law Any legal proceeding arising out of or relating to these terms and conditions or to the goods sold Purchaser shall bring solely and exclusively in the County of Los Angeles In no event may Purchaser initiate any legal proceeding more than six months after the occurrence of the event giving rise to the dispute Seller may make non payment claims until debt is paid in full The above terms and conditions are the only ones governing this transaction and
9. freight both ways and if Seller does take back the goods there will be a restocking service fee that is 35 of the purchase price of the goods product must be in original packaging If Purchaser returns goods claiming that the goods are defective and goods are found to be in working condition by the Seller Purchaser is liable for the return and cost of freight both ways plus an a restocking service fee that is 35 of the purchase price of the goods Built to Order products including Cabinets Racking and Accessories are non returnable Purchaser must notify Seller of non conforming goods within four days of delivery after which time all goods are deemed accepted If an order has been placed and production has started cancellation of your order will be a 15 charge If Purchaser tenders payment with a check that has insufficient funds NSF or stops payment on a check or credit card for any reason Purchaser agrees to pay for all costs associated with the Seller s collection or litigation of such a claim including without limitation general and special damages court costs and attorneys fees Finance charges begin the date of invoice Collection fees plus NSF fee of 50 will be added to your invoice which you agree to promptly pay Title to the goods does not pass until payment is received in full by Seller and Seller retains a security interest in the goods until they are paid for in full however from deliver Purchaser will insure the goods and for
10. it CONNECTED NOTE The temperature set for the Lower Zone must always be the same or higher than the Y temperature set for the Upper Zone For optimal performance the set temperature of the two zones AB should differ by at least 4 F A GROUNDING PRONG SETTING A TEMPERATURE e Touch SET to set the internal temperature for each zone The degrees indicators will appear in the display window marked for UPPER ZONE and w for LOWER ZONE e When you touch SET f for the first time the LED readouts will show the original temperature settings preset factory setting for UPPER ZONE is 50 F 10 C and for LOWER ZONE is 60 F 16 C e Touch SET once The left LED indicator for UPPER ZONE will flash Then touch UP A or DOWN Y to set the desired temperature e When you touch SET A again the right LED indicator for LOWER ZONE will flash Then proceed to touch the UP A or DOWN Y to set the desired temperature for the LOWER ZONE e The temperature will increase by 1 C or 1 F if you touch UP A once or the temperature will decrease by 1 C or 1 F if you touch DOWN Y once e To view the set temperature in either zone at any time touch UP A or DOWN Y and the set temperature will temporarily flash in the LED display for 5 seconds You can touch SET f to view the temperature setting from one zone to the second zone NOTE When using the unit for the first time or after a long period of inactivity there may be a variance of a few degrees betwee
11. lity for the goods sold to the Purchaser once the goods have left the Seller s premises including but not limited to late delivery by the carrier or for events caused by any difficulty carrier incurs in attempting to fit the goods into the Purchaser s designated location due to the size of the goods or any other reason Purchaser assumes all responsibility for delivery payment of freight access measurement installation hook up wiring moving and storage of the goods The transportation of all goods is subject to the terms and conditions which the carrier imposes on Purchaser including but not limited to additional charges imposed per flight of stairs and or additional charges resulting from the carrier s inability to safely and or adequately use the building elevator to lift the goods Any claim for damages incurred during shipment by the carrier of the goods are insured and handled directly with the carrier and must be noted at time of delivery Any damages due to manufacture defects will be handled directly with Seller subject to the Limited Warranty below If the item is damaged by the freight company Purchaser may cancel the order only by paying for freight costs both ways and a 35 restocking fee All sales are final and unless authorized in writing by the Seller Purchaser may not return the goods under any circumstance If Purchaser refuses to accept the goods under any circumstance the Purchaser is liable for the return and cost of
12. n and the unit is truly malfunctioning due to manufacture defect Removal or re installation of unit is not included in warranted costs Purchaser s exclusive remedy is limited at Seller s option to repair or replace defective part s with either new or reconditioned part s Purchaser is responsible for shipping the unit pre paid to designated facility and Seller will pay return shipping charges in the continental United States for items repaired under warranty within 12 twelve months from date of sale Since the natural variation in texture density grain color tone and shade of wood is unavoidable Seller does not guarantee the texture color tone or shade of the wood nor does seller guarantee the colorfastness of wood or against peeling chipping cracking or scratching Note Unfinished wood is subject to warping all wood surfaces must be sealed before placing cellar into service Improper repair or placement of the unit will void the warranty Any third party repair facility must be pre approved in writing by Seller before providing replacement parts under warranty IL Romanzo units Warranty 90 ninety days Replacement part 12 twelve months from the date of sale Non New Units Scratch amp Dent Refurbished Floor Models warranty for compressor units is 90 days from your dated invoice and 30 days for thermoelectric units parts for function only not cosmetic defects These units are refurbished and sold as is Purchaser assumes ri
13. n the selected temperature and the temperature indicated on the LED readout This is normal due to the length of inactivity and will correct itself after the unit is run for a few hours If the unit is unplugged has lost power or is turned off wait 3 to 5 minutes before restarting the unit The unit will not restart before this time delay Uno WWW VINOTEMP COM 17621 South Susana Road Rancho Dominguez California 90221 info vinotemp com PARTS AND SPECIFICATIONS Full shelves Total5 Digital Control Panel Half shelf Total1 Security Lock Base Grille Adjustable Legs Model No VT 28 2Z SSDST 14 75 x 22 5 x 33 125 Note This wine cooler is designed to store standard Bordeaux 750 ml bottles Storing large and or oddly shaped bottles including champagne and sparkling wine bottles will decrease the capacity of your wine cooler a u MEK a lll INSTALLATION e Remove all packing material before using your wine cooler e IMPORTANT Before connecting the unit to a power source let it stand upright for approximately 24 hours This will reduce the possibility of a malfunction in the cooling system from handling during transportation e Clean the interior surface with lukewarm water and a soft cloth e This unit is designed for freestanding and built in installation and indoor use only Position the unit in a dry and well ventilated place Avoid placing the wine cooler near any source of he
14. ng the unit Please be sure to retain your proof of purchase New Leaf SERVIGE Essential consumer protection Add a New Leaf extended warranty to your order and have the security of knowing that if there should be a problem even years in the future New Leaf will be there to assist Usable for any Wine Cellar or other electronic device manufactured by Vinotemp Add this warranty to purchases made from vinotemp com or other qualified venders Warranty must be registered within the first 10 days from original purchase Visit www Vinotemp com to purchase TROUBLESHOOTING You can solve many common wine cellar problems easily saving you the cost of a possible service call Try the suggestion below to see if you can solve the problem before contacting Vinotemp at info vinotemp com SYMPTOM POSSIBLE CAUSE Door will not close e The wine cellar is not level properly e The shelves are out of position e The door gasket is dirty e A bottle in the cellar is too long Unit does not e Check that unit is plugged into the wall socket operate does not e Make sure the wall socket has power If outlet is controlled by a wall have power switch make sure switch is set to on Test wall socket functionality by testing another electrical appliance in the power socket Power is ON but the e Make sure there are at least 3 to 5 bottles in the unit When using the unit unit will not cool for the first time it can take up to 24 hours
15. re will fall below 60 F 16 C For best performance do not install the appliance behind a cabinet door or block the base grille e Avoid locating the unit in moist areas e Plug the wine cooler into an exclusive properly installed grounded wall outlet INSTALLING STAINLESS STEEL HANDLE This wine cellar includes a stainless steel handle that is not required to operate this unit To install the handle please follow the below instructions e Pull away the door gasket in the area where the handle is to be installed you can see two designated holes for handle installation The gasket is easily displaced by hand no tools are necessary Flat Washer e Install the handle tightly as shown below with Hande the two screws lock washers and flat washers Lock Washer provided DO NOT over tighten as this will Screw cause damage to the handle assembly and Door Frame stainless steel surface of glass door e Replace the door gasket to its original position OPERATING YOUR WINE COOLER CONTROLS 9 88 BBP 17621 South Susana Road Rancho Dominguez California 90221 info vinotemp com
16. sks to the quality and performance of goods and assumes the costs of all necessary service or repair not covered herein Element Grills via Element Products LLC grills have a 1 year parts warranty and a thirty day limited parts warranty on grill accessories Warranty period is from the date of sale not from shipping delivery nor installation This Limited Warranty does not cover damage due to such things as accident misuse abuse mishandling neglect acts of God fires earthquakes floods high winds government war riot or labor trouble strikes lockouts delay of carrier unauthorized repair or any other cause beyond the control of the Seller whether similar or dissimilar to the foregoing Seller is not responsible for any damages caused to Purchaser s property resulting from the goods This limited warranty applies only inside the Continental US Alaska Puerto Rico Hawaii and other territories countries are not warranted Purchaser understands and acknowledges that the goods sold here are wine cellars cigar humidors and or other similar units which house wine or cigars or other items Purchaser assumes all risk of using these units including risk of spoilage humidity variations temperature variations leaks fire water damage mold mildew dryness and similar and any other perils that might occur Seller is not responsible for incidental or consequential damages and there are no warranties expressed or implied which extend b
17. to reach the desired temperature e f the room temperature is at the high end of the ambient temperature range it may have more difficulty achieving a low internal temperature e To achieve accurate temperature control the unit should not be used or operated in any of the following locations o Ina sunny place a room with poor air circulation such as a garage or near another heat producing appliance such as a dishwasher oven or refrigerator o With an outlet shared with a refrigerator as the refrigerator will drain power from the wine cellar e Make sure the cooler has proper clearances at side and rear and is located in a well ventilated area Door is not closed tightly or is being opened too frequently Fan is always running e This is simply a function of the cooling system The lower the setting the more the fan will run If the room is very warm the cooler will run more The unit has been designed to run continuously when operating at the lower temperatures Vibrations e Check to make sure the wine cooler is level e The rattling noise may come from the flow of refrigerant As each cycle ends you may hear gurgling noises caused by the flow of the refrigerant This is normal Frost appears in Either too much humidity or too low of temperature inside cabinet Unplug cabinet on back cooler and allow to manually defrost Reconnect when ice has melted If problem persists contact for service instructions Inside light flashes
18. to the base to avoid damage e Tape the door shut e Ensure that the unit stays securely in the upright position during transportation Protect the outside of the appliance with a blanket or similar item ENERGY SAVING TIPS e The unit should be located in the coolest area of the room away from heat sources or direct sunlight e Ensure that the unit has proper allowances on all sides for proper ventilation Never cover any air vents e Only open the cooler door for as long as necessary Frequent opening of the door will affect internal temperature Unotemps WWW VINOTEMP COM Table of Contents IMPORTANT SAFETY INSTRUCTIONS anna a 6 ELECTRICAL CONNECTION ee ee een 7 PARTS AND SPECIFICATIONS ann a 8 INSTALLATION isso ER 9 OPERATING YOUR WV TMP COOLER se aa 9 CARE ANDZMAINTENANEE anne n h ee ee 11 TROUBLEESHOOTING socio ua 13 TERMS OF SALE AND WARRANTY se ea ae 14 SERVIGE amp IMPORTANT NOTREE u Me commana 16 17621 South Susana Road Rancho Dominguez California 90221 info vinotemp com IMPORTANT SAFETY INSTRUCTIONS e Do not operate this or any other appliance with a damaged cord e Do not operate if housing is removed or damaged e Exercise caution and use reasonable supervision when appliance is used near children Never allow children to operate play with or crawl inside the appliance Keep packing materials away from children e Before performing any maintenance or cleaning ensure that the unit is
19. traditional N N i Bordeaux 750 ML bottles and include bulk storage NOTE Wine bottles on bottom shelf cannot be longer than _ 3 Bottle Arrangement approx 12 inches SHELVES To avoid damaging the door gasket ensure that the door is fully opened when pulling the shelves out of the rail compartment The slide out shelves allow bottles of wine to be viewed and removed more easily Any of the shelves can be removed to store larger bottlers For easy access to the storage bottles you must pull the shelf approximately Y out of the rail compartment however this unit was designed with a plastic post on each side of the shelf track to prevent bottles from falling When removing the shelf from the rail compartment make sure to remove all items first Then move the shelf to the position where the notch of the shelf is exactly under the plastic post and lift the shelf In order to replace the shelf repeat steps described above in reverse DOOR LOCK Your unit is provided with a lock and key combination The keys are located inside the plastic bag that contains the Owner s Manual Insert the key into the lock and turn it counterclockwise to unlock the door To lock the door do the reverse operation making sure metal pin is engaged completely Remove the key and place it in a secure place for safekeeping CARE AND MAINTENANCE CLEANING YOUR WINE COOLER IMPORTANT Always unplug the unit before cleaning or performing maintenance Ne
20. unplugged or that the power line is disconnected e Do not clean appliance with flammable fluids Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance The fumes can create a fire hazard or explosion e Exercise caution when moving and installing the unit The cooler is heavy and may require two or more people when moving the unit to prevent strain or injury e To ensure proper ventilation for your appliance the front of the unit must be completely unobstructed Choose a well ventilated area with temperatures above 60 F and below 90 F e Locate the unit away from direct sunlight and sources of heat stove heater radiator etc This unit is intended for indoor use only and must be installed in an area protected from the elements e Place the appliance on a solid level surface e Do not attempt to repair or replace any part of your appliance unless it is specifically recommended in this manual All other servicing should be referred to a qualified technician e Connect to properly polarized outlets only It is recommended that a separate circuit serving only your appliance be provided Use receptacles that cannot be turned off by a switch or pull chain Be sure that the plug is fully inserted into the receptacle e To protect against electric shock do not immerse appliance plug or cord in water or other liquids Avoid locating the unit in moist areas e This appliance is
21. ver use harsh cleansers or scouring pads to clean any part of the unit Turn off the power unplug the appliance and remove all items including shelves Wash the inside surfaces with a warm water and baking soda solution The solution should be about 2 tablespoons of baking soda to a quart of water Wash the shelves with a mild detergent solution Wring excess water out of the sponge or cloth before cleaning control panels or any electrical parts Wash the outside cabinet with warm water and mild liquid detergent Rinse well and wipe dry with a clean soft cloth 17621 South Susana Road Rancho Dominguez California 90221 info vinotemp com POWER OFF ON ELECTRICAL CONNECTION To control this appliance turn on off To turn OFF the appliance touch the and f marks at the same time for 5 seconds Improper use of the grounded plug can result in the risk of electrical shock SET If the power cord is damaged frayed or shows cracks or abrasions across its length have it replaced at an authorized service center To set or view the internal temperature setting for each zone For your protection this unit is equipped with a 3 conductor cord set that has a molded 3 prong LIGHT 9 l l grounding type plug and should be used in combination with a properly connected grounding type To control the inner light turn on off outlet up A e Do not under any circumstances cut or remove the third ground prong from the power cord i R
Download Pdf Manuals
Related Search