Powr-Flite PF53 Use and Care Manual
Contents
1. COMMERCIAL FLOOR CARE EQUIPMENT WET DRY VACUUM Models PF51 PF53 PF55 PF57 OPERATING INSTRUCTIONS COMMERCIAL WET DRY VACUUM Equipment must be operated serviced and maintained in accordance with the manufacturer s instructions as Save These Instructions X8683 11 05 SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE When using a wet dry vacuum basic precautions should be followed Read all instructions before using your vacuum IMPORTANT SAFETY ADVICE READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE When using an electrical appliance basic precautions should always be followed WARNING To reduce the risk of fire electric shock of injury only use dryer as described in this manual You must have training in the operation of this machine before using it Read all instructions carefully before use Keep children and unauthorized persons away from the machine when in use Do not leave the machine plugged in when not in use Switch the machine off before removing the plug from the outlet o When unplugging pull the plug not the cord The machine must be unplugged prior to cleaning or servicing the machine Keep the power cord clear of moving parts Do not run the machine over the power cord Do not operate the machine with a damaged power cord or plug or if the machine malfunctions or is damaged in any way O Do not use where hazardous dust is prese2. into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances This appliance is for use on a nominal 120 volt circuit and has a ground plug see illustration right Make sure that the appliance is connected to an outlet having the same configuration as the plug No adaptor should be used with this appliance i WARNING Improper connection of the equipment grounding conductor can result in a risk of electric shock Check with a qualified electrician or service per son if you are in doubt as to whether the outlet is properly grounded Do not modify the plug provided with the appliance if it will not fit the outlet have a proper outlet installed by a qualified electrician Grounded Outlet o Grounded Outlet Box Grounding pin DRY OPERATION OF VACUUM The wet dry vacuums are equipped with bypass motors Install the cloth filter place the motor head on the canister and snap down the hold down clamps WET OPERATION OF VACUUM The wet dry vacuums are equipped with a bypass motor so that the work ing vacuum is separated from the cooling air flow To pick up water the dry filter must be removed and the float cage assembly must be in place the motor head placed on the canister and the hold down clamps locked down The safety float located in the protective wire frame in the tank stops the vacuum action of the motor head when the maximum recovery of liquids is reach
3. 2 shaft 15 5 8 26 5 13 WD16 middle seat WD93 small wheel WD53 gasket WD94 shaft for small wheel 12 WD15 motor WD95 squeegee long WD54 gasket WD96 squeegee short WD55 gasket WD56 sponge Model PF57 Wiring Diagram SWITCH CAPACIT 210 Loss of Suction CAUSE 1 Tank full 2 Dry filter assembly clogged 3 Clogged hose or wand 4 Tank rim is dented 5 Loose or broken fan 6 Motor not working 7 Float not functioning 8 Seal worn Motor is not running CAUSE 1 Broken switch 2 Defective power cord 3 Defective motor Dust blowing from unit when running CAUSE 1 Cloth filter dirty 2 Cloth filter is torn 3 Cloth filter is not installed chimney soot or sheet rock Water blowing from unit when running CAUSE 1 Tank is full of liquid 2 Sudsy or foamy liquid is being picked up TROUBLE SHOOTING GUIDE SOLUTION 1 Empty Tank 2 Clean cloth filter 3 Remove obstruction 4 Replace tank 5 Contact manufacturer of service center 6 Contact manufacturer or service center 7 Check to see if float moves freely or tank is full 8 Replace seal SOLUTION 1 Contact manufacturer or service center 2 Contact manufacturer or service center 3 Contact manufacturer or service center SOLUTION 1 Clean cloth filter 2 Replace filter 3 Install cloth filter w
4. Ground Model PF53 Parts per T7 free e Model PF53 Parts Dolly Assembly ref 1 ref item description WD78 handle WD17 wire plate WD79 holder 19 WD87 power switch WD80 handle 13 WD16 middle seat WD40 front wheel 11 WD14 base WD61 rear wheel WD69 sponge WD81 rear wheel shaft WD70 sponge WD73 plate WD82 base block WD74 fixed plate WD83 top block WD62 dolly WD84 blocker FM17 hex screw WD68 gasket WD12 screw WD54 gasket top WD52 spring 12 WD15 motor WD85 stopper Tank Assembly ref 2 9 WD87 housing base WD38 stainless tank 8 WD10 base cover WD63 clamp assembly 7 WD9 float WD44 nut 6 WD8 frame WD45 suction coupler 42 WD37 spring WD86 button base 41 WD36 paper filter WD46 button 40 WD35 hook WD47 spring WD50 rubber washer Accessories WD76 rubber washer ref item description WD77 holder 5 WD7 filter frame long WD51 fixed plate 3 WD3 filter and gasket WD59 lock cover 22 WD25 hose assembly WD60 lock button 21 WD24 connector 20 WD23 sea Top Head Assembly 25 WD28 bend connector ref item description 26 WD29 extension wand 10 screw 24 WD27 fixer 17 WD20 handle 23 WD26 connector 16 WD65 top cover 29 WD32 crevice too 18 WD66 power cord 30 WD33 round brush Model PF53 55 Wiring Diagram S
5. WITCH CAPACITOR ERMINAL OCK wa Ground Model PF55 PF57 Parts Model PF55 PF57 Parts ref item description WD85 seal plate Dolly Assembly ref 1 11 WD14 holder WD71 handle 9 WD11 motor seat WD72 holder 8 WD10 base WD75 handle 7 WD9 float WD40 front wheel 6 WD8 frame FM17 hex screw 42 WD37 spring WD41 rear wheel 41 WD36 paper filter WD42 shaft of rear wheel 40 WD35 hook WD43 plate WD12 screw Cord Assembly WD74 fixed plate 18 WD21 power cord WD1 dolly WD17 cord plate WD18 screw Tank Assembly ref 2 19 WD22 power switch WD2 stainless tank WD43 clamp assembly Accessory WD44 nut 22 WD25 hose assembly WD45 suction coupler 21 WD24 connector WD86 button base 20 WD23 seal WD46 button 25 WD28 bend connector WD47 spring 26 WD29 extension wand WD50 rubber washer 24 WD27 holder WD76 washer 23 WD26 connector WD77 holder 29 WD32 crevice tool WD51 fixed plate 30 WD33 round brush WD59 fixed holder WD60 fixed holder Nozzle WD52 spring WD86 squeegee WD87 wheels Filter Assembly WD88 shaft WD4 holder 5 WD7 frame Nozzle Body WD89 bottom plate Top Assembly WD90 base cover 17 WD20 handle WD91 rear wheel 16 WD19 top cover WD9
6. ed WAND AND ATTACHMENT INSTRUCTIONS To assemble the two piece wand 1 Match the alignment ridges of the upper and lower wand sections 2 Push the upper wand into the lower wand To assemble tools 1 Slide the swivel cuff of the tool onto the tapered lower wand 2 Turn swivel cuff 1 4 turn to tighten When the tank is full using the overturning mechanism to empty the tank 1 Remove the top head 2 Take out the filter with frame 3 Unlock the knob 4 Grip the handle with one hand use one foot to brace the dolly and lift the handle by the other hand to empty the tank NOTE When the water level in the tank exceeds the safety level the safety devise will automatically block the inlet and motor turning sound will be changed but power will remain ON The power must be turned OFF before emptying the tank REMOVE THE PAPER FILTER The paper filter must be removed for wet recovery Push the metal ping counterclockwise to release the filter Remove the paper filter HOSE ATTACHMENT INSTRUCTIONS The hose and swivel connector are pre assembled at the factory To attach the swivel connector to the intake fitting of the canister 1 Push the grooved cuff straight into the intake fitting 2 To remove press the release button on top of the intake fitting while pulling the grooved cuff out MAINTENANCE AND SERVICING 1 To dismantle unclip both latches and remove top housing and filter with frame 2 Wash the
7. filter with water and allow it to dry 3 After washing remove excess water with a gentle squeegee 4 Replace the filter and top housing and fasten the latches NOTE This cleaner is designed with a powerful suction Do not be alarmed if the motor noise increases when performing tougher cleaning work PARTS NAME WAND CONNECTOR TOP HEAD 2 BOIA DI FIXED GROOVE CURVE CONNECTOR PAPER FILTER FILTER WITH FRAME mr CLIP SUCTION COUPLER BUTTON OF REVERSING STAINLESS LA I HANDLE TANK nsa A MS l 7 VAL prusH _CREVICE A N TOOL a D BRUSH NOZZLE De SQUEEGEE NOZZLE SUPPORT PIPE DOLLY Model PF51 Parts Model PF51 Parts ref item description 2 WD88 power cord 4 WD89 top cover 7 WD90 sponge WD91 sponge WD92 sponge WD93 sponge 10 WD94 relief valve 11 WD95 gasket motor 12 WD15 motor 13 WD96 motor holder 15 WD97 cover 17 WD99 float 18 WD100 handle 20 WD101 switch 29 WD102 filter 30 WD103 tank 33 WD98 clamp 41 WD104 wheel holder 42 WD105 wheel 49 WD111 hose assy 53 WD106 wand 56 WD107 squeegee nozzle 57 WD108 floor tool 58 WD109 dust brush 59 WD110 crevice tool Model PF51 Wiring Diagram SWITCH CAPACITUR TERMINAL BLOCK
8. hen vacuuming very fine dust SOLUTION 1 Empty tank 2 Add defoamer to tank The Powr Flite Limited Warranty The manufacturer warrants to the original purchaser that products manufactured are free from defects provided such goods are installed operated and maintained in accordance with written manuals or other instructions for a period of 1 year from date of pur chase on workmanship motor and parts In case you as our customer meet any trouble with your machine contact a Powr Flite representative who will be happy to be of service to you and will take care of any warranty issues kovwmhlite COMMERCIAL FLOOR CARE EQUIPMENT 3101 Wichita Court Fort Worth TX 76140 800 880 2913
9. nt Do not use in an explosive atmosphere Do not use where flammable liquids or gasses are present Do not use or pick up flammable chemicals or liquids with this machine Take care when using the machine near the top of stairs to avoid overbalancing Maintenance and repair must be done by authorized personnel only Wear suitable footwear to avoid slipping Do not operate this machine in bare feet or with open toed shoes or sandals O Do not smoke when using the machine o Do not pick up anything that is burning or smoking such as cigarettes matches or hot ashes Do not use without dust bag and or filters in place o Do not pull or carry by cord use cord as a handle close door on cord or pull cord around sharp edges or corners Keep cord away from heated surfaces Store cord properly when not in use STORAGE INSTRUCTIONS Store appliance on floor indoors away from heated surfaces Do not pull or carry by cord use cord as a handle close door on cord or pull cord around sharp edges or corners Keep cord away from heated surfaces Store cord properly when not in use 2 GROUNDING INSTRUCTIONS This appliance must be grounded If it should malfunction or break down grounding provides a path of least resistance for electric current to reduce the risk of electric shock This appliance is equipped with a cord having an equipment grounding conductor and grounding plug The plug must be plugged
Download Pdf Manuals
Related Search