GE CGU366SEHSS Instructions / Assembly
Contents
1. MAIN Nat Use 108XL or ORIFICES 190XN orifices LE for all burners e Turn the grill knob to LO and remove the knob by pulling straight off p Insert a small flat blade screwdriver into the hole in the A Return the unused orifices to the holder Reattach center of the valve stem to engage set screw sure to place the unused the holder and the instruction sheet with screw in e To convert the LO setting from natural gas to LP turn the original storage location the screw clockwise until it stops B Replace the burner heads caps and top grates On about 3 4 turn It may be necessary range models replace rear vent trim to grasp the exterior of the valve stem with a pair of pliers to prevent the valve stem from rotating as the 4 CHANGE GRILL ORIFICE if present set screw is adjusted e To convert the LO setting from the LP Locate the 1 1 2 long Grill orifice to natural gas setting turn the screw Select for your gas type LP 047 NAT 067 counterclockwise about 3 4 turn Installation Instructions for Gas Conversion 5 CHANGE GRIDDLE ORIFICE if present Locate the 3 4 long griddle orifice Select for your gas type LP 047 NAT 076 A Lift off the griddle flue Griddle Flue Cover cover Remove the 2 inside clamping SCrews Lift out the cast iron grease trough Slide the griddle tow2. Installation Instructions 36 Rangetop Caf Safety Information BEFORE YOU BEGIN Read these instructions completely and carefully M PO RTANT Save these instructions for local inspector s use IMPORTANT observe al governing codes and ordinances Note to Installer Be sure to leave these instructions with the Consumer e Note to Consumer Keep these instructions with your Owner s Manual for future reference e Completion Time 1 to 3 hours e Proper installation is the responsibility of the installer Product failure due to improper installation is not covered under the warranty See Owner s Manual for warranty information WARNING This appliance must be properly grounded Follow directions in Electric Supply of this manual Failure to do so may result in electric shock For local service in your area 1 800 444 1845 For Service in Canada call 1 800 561 3344 For Parts and Accessories call 1 800 626 2002 If you received a damaged rangetop you should contact your dealer In the Commonwealth of Massachusetts e This product must be installed by a licensed plumber or gas fitter e When using ball type gas shut off valves they shall be T handle type e A flexible gas connector when used must not exceed 3 feet If sold outside the U S and Canada WARNING If you wish to use this product with Liquefied Petroleum LP gas containing greater
3. CHANGE GRILL ORIFICE cont IMPORTANT Find your model number below Read A Rernove the grill cover each orifice label to identify and install them in the grates and grate frame Lift exact locations shown the radiant baffle straight ZDP304 SIMMER ORIFICES up and off LP Nat e a Remove the 2 hex head e A 34SL or 51SN orifice OOOO e e will be used on all burners screws from the top of the igniter e Remove one screw from a each side of the burner ZDP304 MAIN ORIFICES surround e Lift out the surround 126HXN Carefully push the Burner Use a 108XL BER E or 190XN orifice igniter aside and under Surround A 84XL or for the right the burner Pa not pull 126HXN orifice front burner or pinch the wire will be used Remove 4 burner on these three attachment screws 2 burners at the front and 2 at the back Slide the burner assembly toward the ZDP364 ZDP366 ZDP484 ZDP486 ee and out of the gas inlet SIMMER LP Nat 34SL or 515N orifice will ORIFICES ca be used on all burners Use a 1 2 deep well E socket to remove and replace the orifice Reverse these steps to re assemble the grill Be orifice in the holder for a possible future use Ea E Adjust Grill LO Setting e Make certain gas and electricity to unit are turned off
4. Allow 12 minimum clearance to an adjacent wall on each side Working areas adjacent to the rangetop Back Y_ should have 18 minimum clearance 2 1 2 Min between countertop and the bottom of the wall cabinet For island installation maintain 2 1 2 in minimum from cutout to back edge gt gt Island of countertop and 3 in minimum from Cutout cutout to side edges of countertop see Top View top view combustible 12 Minimum 12 Minimum to Adjacent Wall 12 Minimum to Combustibles or 0 to non combustible material above the cooking surface 48 Min to Combustibles Clearance Design Information INSTALLATION OPTIONS Le 28 13 16 To Front of Control Knobs 27 1 2 To Front of Bullnose 1 2 T eT 3 Countertop lage i Level Finished back edge a 13 32 of control panel u 1 3 16 Countertop Level f 1 1 32 Y Back edge TE Stub of chamfer 23 1 2 26 26 3 4 To Front of Control Panel t Include the overhang of the rear trim when countertop continues behind the product The overhang is decorative only The weight of the rangetop is fully supported by the side trims Minimum cabinet cutout depth from Maximum countertop cutout depth the back of the rear trim to the back from the back of the rear trim finished edge of the control panel to the back edge of chamfer at the typically th
5. trim on ranges only to access the regulator gt gt gt gt Ss The Rangetop regulator is on the left bottom corner Shut off the gas supply by closing the manual shut off valve in the unit or at the wall Convert the pressure regulator e Unscrew the cap with plunger e Place your thumb against flat side of the plunger and press down to snap the plunger out of the cap e Carefully look at the plunger to locate the Cap Gasket NAT or LP position a N e Turn the plunger over so that the desired T p as is showing near e Mecho YNET the bottom LP Positi e Snap the plunger N back into the cap e Screw the cap back onto the regulator Position 7 AL Pressure Regulator 3 CHANGE BURNER ORIFICES 2 to 2 4 mm or 3 32 tip size INSTALLATION TIP First remove all orifices and then start replacing them This will help to prevent the possibility that some may not be replaced A Remove the burner grates burner caps and burner heads B Loosen the top burner Spark orifices using a 7 mmnut Igniter driver Use small pliers to carefully lift out the orifices The main orifice is located low in the center of the burner while the simmer orifice is located higher beside the center of the burner orifice Burner Cap Installation Instructions for Gas Conversion CHANGE BURNER ORIFICES cont 4
6. LE ARE REQUIRED FOR PROPER INSTALLATION Installation must conform with local codes In the absence of local codes the rangetop must comply with the National Fuel Gas Code ANSIZ223 1 NFPA 54 latest edition and National Electrical Code ANSI NFPA 70 latest addition In Canada installation must conform with the current Natural Gas Installation Code CAN CGA B149 1 or the current Propane Installation Code CAN CGA B149 2 and with local codes where applicable This rangetop has been design certified by CSA International according to ANSI 221 1 latest edition and Canadian Gas Association according to CAN CGA 1 1 latest edition Leak testing of the appliance shall be conducted according to the manufacturer s instructions Design Information CONTENTS Design Information Models Available Backsplash Accessories Product Dimensions and Clearances for 48 Wide Models Product Dimensions and Clearances for 36 Wide Models Installation Options Installation Preparation Tools and Materials Required Power Supply Locations Remove Packaging MODELS AVAILABLE Rangetops are factory set for natural gas or LP gas Order the model for your installation situation 48 Natural Gas Models ZGU484NG 4 gas burners grill and griddle ZGU486NR 6 gas burners and grill ZGU486ND 6 gas burners and griddle 48 LP Gas Models ZGU484LG 4 gas burners grill and griddle ZGU486LR 6 gas burners and grill ZGU486LD 6 gas burners an
7. MPORTANT OBSERVE ALL GOVERNING CODES AND ORDINANCES NOTE TO INSTALLER Be sure to leave these instructions with the Consumer NOTE TO CONSUMER Keep these instructions with your Owner s Manual for future reference BEFORE YOU BEGIN This kit provides for the installation of a 12 high backsplash for 30 36 or 48 Professional Ranges and Rangetops TOOLS AND MATERIALS REQUIRED eGloves to protect against sharp edges eT 15 and 2 Phillips screwdrivers e Drill with 3 32 and 9 64 bits eSafety glasses eLevel e Pencil Wall Support Panel Cover Panel This Kit Includes Wall support panel Cover panel e Hardware package with 5 Stainless Steel Torx 15 8 self tapping screws 5 Phillips 2 pan head wood 10 screws Hardware Package 12 INSTALL 12 BACKSPLASH WARNING this backsplash must be securely fastened to the wall Failure to do so could result in damage or personal injury e Install and level the range or rangetop and the range hood according to the installation instructions Remove the backsplash packaging and protective film Use a level to pencil a horizontal line on the wall 1 8 above the range or rangetop The 1 8 gap allows the cover panel to overlap the wall support panel Locate wall studs on each side Where studs are not available plan to use wall anchors not provided Align the wall support panel on the marked horizontal line and centered left to
8. ard the rear and out of the 8 hold down tabs along the bottom Carefully lift and hold the griddle while pulling additional length of the capillary from the entry TH hole Stand the griddle on end in the grease sump Remove the 2 hold down screws at the rear of the burner Pull the burner straight back toward the rear and out of the gas inlet Use a 1 2 deepwell socket to remove and replace the orifice positioned on the inside only Do not remove the outermost screws they are for leveling Leveling Screw Clamping Screws D Back of Range E Front of Range Reverse these de to reassemble the griddle Push excess capillary back into the entry hole Place the unused orifice in the holder for possible future use 17 6 ADJUST BURNER FLAMES Normally burners do not need further adjustment Make adjustments only when necessary A Turn on the gas Plug in electrical cord B Turn all burners on highest setting and check the flames They should be blue in color When using LP gas the flames may have some yellow tipping at the ends of the flame Foreign particles in the gas line may cause an orange flame at first but this will soon disappear C Turn the burner knob to LO while observing the flame Adjust the setting of the upper row of flames using the valve bypass screw as follows Adjustments must be made with two other burn
9. aterial above the cooking surface 48 Min to ADDITIONAL CLEARANCES Combustibles Allow 12 minimum clearance to an adjacent wall on each side Working areas adjacent to the rangetop should have 18 minimum clearance 2 1 2 Min between countertop and the bottom of the wall cabinet Clearance For island installation maintain 2 1 2 in minimum from cutout to back edge lt gt Island of countertop and 3 in minimum from Cutout cutout to side edges of countertop see Top View top view Design Information PRODUCT DIMENSIONS AND CLEARANCES FOR 36 MODELS Universal Utility Locations ass 27 1 2 to a with Front of Bullnose Locate gas inlet on back wall or on floor 2 from back wall 48 Minimum to Combustibles WARNING Installations without a hood Non require 48 minimum to combustibles above the rangetop A custom hood _ installation with exposed horizontal 13 Max combustible surfaces must have an Auto On feature Refer to hood installation instructions for specific hood clearances material The surface of the entire back wall above the countertop and below the hood must be covered with a non combustible material such as metal ceramic tile brick marble or other stone The opening between a 4 high backsplash must be 36 to allow the rangetop to slide back against the wall ADDITIONAL CLEARANCES
10. breaker or fuse box A WARN NG This conversion must be performed by a qualified installer or gas supplier in accordance with the manufacturer s instructions and all codes and requirements of the authority having jurisdiction Failure to follow instructions could result in serious injury or property damage The qualified agency performing this work assumes responsibility for the conversion A WARN NG The rangetop as shipped from the factory is set for use with its intended gas If you wish to use your rangetop with the alternate gas you must first replace the orifices and convert the pressure regulator A WAR N N G The following adjustments must be made before turning on the burner Failure to do so could result in serious injury Be sure pressure regulator has been converted as described in Step 2 TOOLS YOU NEEDED FOR CONVERSION Ecco 1 4 and 7mm Nutdrivers Te Small Flat Head Screwdriver Crescent Wrench Safety Glasses 1 2 Deepwell Socket Wrench 60 mm long ere Philips Small Pliers Screwdriver 1 ORIFICE HOLDER ne The range orifice holder is located behind the front access panel at the bottom of the range The rangetop orifice holder is located inside the range insulation cover Additional orifices may be present Use only the orifices specified in the instructions for your range or rangetop Burner Orifices A Remove the rear vent Range Regulator
11. d griddle BACKSPLASH ACCESSORIES All models require 12 minimum clearance to a vertical combustible surface at the rear If clearance is less than 12 the entire surface of the back wall above the countertop and the full width of the rangetop must be protected by a backsplash The backsplash must be constructed of non combustible material such as metal ceramic tile brick marble or other stone Two Backsplash Accessories Available e The 12 high stainless steel backsplash accessory is available Use this backsplash in combination with a custom non combustible backsplash built beyond the 12 height The combined height of the backsplash accessory and the custom backsplash must reach the bottom of a hood or when there is no hood to 48 above the cooking surface Installation Instructions Step 1 Cut the Countertop Opening Step 2 Install the Rangetop Step 3 Connect Rangetop to Gas Step 4 Connect Electrical Step 5 Check Burners Finalize Installation Installation Checklist Install the Rangetop Backsplash Accessory Install the Adjustable Backsplash Accessory Gas Conversion 36 Natural Gas Models ZGU364ND 4 gas burners and griddle ZGU364NR 4 gas burners and grill ZGU366N 6 gas burners CGU366S 6 gas burners 36 LP Gas Models ZGU364LD 4 gas burners and griddle ZGU364LR 4 gas burners and grill ZGU366L 6 gas burners An adjustable 30 to 36 high backsplash with shelf is al
12. e minimum cabinet depth sides of the control panel typically front to back Maximum cabinet cutout the maximum countertop cutout depth depth is 26 minus the countertop front to back Minimum countertop overhang cutout depth is 25 1 4 Rangetop Rangetop 2 1 2 Above Adjacent O Countertops O 1 2 Above Adjacent Countertops Control panel projects forwards from Front of deep cabinets can align with control standard depth cabinets panel beveled edge Installation Preparation TOOLS REQUIRED Drill and Saber Saw Appropriate Bits Measuring Tape Adjustable Wrench ce o 1 4 Driver or Wrench Carpenter s Square Safety Glasses Ec Phillips 2 Screwdriver POWER SUPPLY LOCATIONS Gas Supply e The natural gas models are designed to operate at 5 water column pressure For proper operation the pressure of the natural gas supplied to the regulator must be between 7 and 13 water column e The LP models are designed to operate at 10 water column pressure For proper operation the pressure of the LP gas supplied to the regulator must be between 11 and 13 water column Locate the pipe stub on the back wall or floor see Product Dimensions and Clearances Use 5 foot maximum length 5 8 O D flexible gas supply line 3 foot in Massachusetts e Install a manual shut off valve in the gas line not provided in an easily accessible locatio
13. ers in operation on a medium setting This prevents the upper row of flames from being set too low resulting in the flame being extinguished when other burners are turned on D To adjust the flame remove the knobs Insert a small flat blade screwdriver into the hole in the center of the valve stem to engage screw e If the flames are too small or flutter turn the screw counterclockwise e If the flames are too large turn the screw clockwise E Make the adjustment by slowly turning the screw until flame appearance is correct Notes Notes 19 Notes 20
14. ion REMOVE PACKAGING e Cut the ties holding the grill grate to the grill frame CAUTION Griddle Flue Cover Stand clear The ends of the cut metal banding may snap toward you Cut the metal banding e Remove packaging tape and foam Dispose of packaging materials properly e Remove grill griddle covers grill grate and burner grates e Lift out cast iron griddle flue cover grease troughs and pads e Lift off burner caps and remove foam pad then lift off burner heads and remove foam pad Installation STEP 1 CUT THE COUNTERTOP OPENING Backsplash Allow Additional Clearance Below the Rangetop Burner Box for the Regulator and Gas Connections p 48 wide models are designed to fit in 48 or wider base cabinets Measure carefully when cutting the countertop Make sure sides of the opening are parallel e Allow 8 free space below the top surface of the countertop e Allow additional clearances below the burner box to install the regulator and make house supply connections Use a 90 elbow to route the gas connections and limit interference with drawers or other cabinetry features e These rangetops are designed to hang from the countertop by their side flanges e Smooth any rough edges on the countertop before installing the rangetop Formica countertop edges must be finished The countertop must be strong enough to support the
15. ld illuminate STEP 5 CHECK BURNERS Check to be sure that burner heads and caps are securely seated Burner Cap Properly Seated Burner Cap Not Properly Seated Check for proper ignition Push in one control knob and turn to LITE position The igniter will spark and the burner will light the igniter will cease sparking when the burner is lit First test may require some time while air is flushed out of the gas line Turn knob to OFF Repeat the procedure for each burner IMPORTANT If the igniter electrodes continue to spark after the burners are lit check that each burner component is assembled properly Refer to the Owner s Manual e Burner flames should be blue and stable with no yellow tips excessive noise or lifting of the flame from the burner If any of these conditions exist check that the burner ports are not blocked If one of these conditions continues call for service FINALIZE INSTALLATION Place the burner grates over the burners The grates should be seated and should nat rock The griddle is secured with screws It is designed to be stationary and should not be removed The griddle has two leveling screws beneath the rear flue cover that can be used to adjust to the desired slope Griddle Flue Cover Clamping Screws The two inner screws are clamping screws for securing the griddle in place Loosen these two screws before leveling Do not remo
16. n Make sure the homeowner knows where and how to shut off the gas supply to the rangetop MATERIALS PROVIDED Hal Da Regulator Strap Joint Sealant Shut Off Valve Pipe Fittings 5 foot maximum length 5 8 O D CSA approved flexible metal gas supply 3 foot maximum length in Massachusetts only NOTE Purchase new flexible line do not use previously used flexible gas line Electric Supply These rangetops must be supplied with 120 volt 60 Hz and connected to a dedicated properly grounded branch circuit protected by a 15 amp circuit breaker or time delay fuse The power cord of this appliance is equipped with a three prong grounding plug which mates with a standard three prong grounding wall receptacle to minimize the possibility of shock hazard from this appliance If the electrical service provided does not meet the above specifications it is recommended that a licensed electrician install an approved outlet DO NOT UNDER ANY CIRCUMSTANCES CUT OR REMOVE THE THIRD GROUND PRONG FROM THE POWER CORD DO NOT USE AN EXTENSION CORD WITH THIS APPLIANCE e Locate the electric supply within the area shown or within reach of the rangetop s four foot power cord To avoid tangling cord with items stored in the cabinet locate the receptacle on rear wall inside the cabinet Receptacle Box Cover Plate f Three Prong Plug Three Prong Receptacle Installation Preparat
17. rence with drawers or other cabinetry features However it is not recommended because it will result in a drop in gas pressure e Make sure the regulator is installed in the right direction See arrow on the underside of the regulator NOTE Instead of using solid piping to connect to pressure regulator an approved flexible metal appliance connector may be used between the pipe stub and the shut off valve to the pressure regulator if local codes permit Turn on gas and check for leaks Use a liquid leak detector at all joints and connections in the system Hold Down Strap Location and Attachment Back Wall Rangetop Burner Box 1 2 N PT Gas Inlet Regulator Supplied Solid Piping or Flexible Connector C AA E zu S Pipe Stub From m House Gas Supply IMPORTANT Disconnect the rangetop and the individual shut off valve from the gas supply piping system during any pressure testing of that system at test pressures greater than 1 2 psig Isolate the rangetop from the gas supply piping system by closing the individual manual shut off valve to the rangetop during any pressure testing of the gas supply piping system at test pressures equal to or less than 1 2 psig 10 Installation STEP 4 CONNECT ELECTRICAL Plug power cord into properly grounded receptacle e Press the button on the left side of the control panel The lights above the knobs shou
18. right The wall support panel must be secured to the wall at all 4 corners Use wood screws provided or wall anchors not provided to secure the support panel to the wall Place the cover panel over the wall support panel and secure with Torx screws provided Install 2 screws on each side Install 4 Wood Screws Install T 15 __ Screws ZXADJB30PSS ZXADJB36PSS ZXADJB48PSS Accessory Installation ACCESSORIES 30 TO 36 ADJUSTABLE BACKSPLASH not included WARNING To prevent ignition of combustible materials the entire back wall above the range must be protected by a backsplash constructed of non combustible material BEFORE YOU BEGIN i n completely IMPORTANT Save these instructions for local inspector s use IMPORTANT OBSERVE ALL GOVERNING CODES AND ORDINANCES NOTE TO INSTALLER Be sure to leave these instructions with the Consumer NOTE TO CONSUMER Keep these instructions with your Owner s Manual for future reference e This backsplash adjusts to fit the space between the top of the range and the bottom of the hood from 30 Min to 36 Max height e Maximum shelf load bearing weight is 40 lbs TOOLS AND MATERIALS REQUIRED eGloves to protect against sharp edges eT 15 and 2 Phillips screwdrivers e Drill with 3 32 and 9 64 bits eSafety glasses Top Wall Support aia Top Cover e Pencil with Shelf lt lt This Kit Includes Top wall support e Bottom wall
19. so available This backsplash fills in the space between the top of the rangetop and the bottom of the hood The shelf is positioned so that heat lamps from the bottom of a professional hood are directed towards the shelf 12 High Backsplash ZX12B48PSS for 48 wide rangetops ZX12B36PSS for 36 wide rangetops 30 to 36 Adjustable Height Backsplash With Shelf ZXADJB48PSS for 48 wide rangetops ZXADJB36PSS for 36 wide rangetops Design Information PRODUCT DIMENSIONS AND CLEARANCES FOR 48 MODELS 27 1 2 to Universal Utility Locations Locate gas inlet on back wall or on floor 2 from back wall 48 Minimum Mini 12 Minimum to to Combustibles Adjacent Wall WARNING Installations without a hood Nom require 48 minimum to combustibles ae 12 Minimum above the rangetop A custom hood en Each Side installation with exposed horizontal 13 Max gt combustible surfaces must have an Auto On feature Refer to hood 18 Mi installation instructions for specific hood clearances The surface of the entire back wall above the countertop and below the hood must be covered with a non combustible material such as metal ceramic tile brick marble or other stone The opening between a 4 high backsplash must be 48 to allow the rangetop to slide back against the wall 12 Minimum to Combustibles or 0 to non combustible m
20. support Top cover with shelf e Bottom cover e Hardware package with 9 Stainless Steel Torx 15 8 self tapping screws 9 Phillips 2 pan head wood 10 screws 3 Stainless Steel 2 truss head 10 screws for alternate installation method Bottom Wall Support Hardware Package INSTALL THE WALL SUPPORT PANELS WARNING The wall support panels must be securely fastened to the wall Failure to do so could result in damage or personal injury IMPORTANT This backsplash is designed to cover the wall between the bottom of the hood and the top of the range The vent hood should be installed over the rangetop or range before installing this backsplash e Install and level the Range Rangetop according to the product installation instructions Remove backsplash packaging and protective film Locate wall studs on each side Where studs are not available plan to use wall anchors not provided Use a level to pencil 2 horizontal lines on the wall one 1 8 below the vent hood and the other 1 8 above the Range Rangetop This 1 8 space allows the cover panels to overlap the wall supports Secure the top wall support panel to the wall with 4 wood screws through the outermost studs Use 4 wood screws to secure the bottom wall support panel The center slot should be positioned at the top The gap between the top and bottom support panels will be covered by the top cover with shelf Secure the top panel to the
21. than 10 butane you must purchase the butane conversion kit WB28K10589 To order please call 1 888 664 8403 or 1 787 276 4051 Failure to do so may result in carbon monoxide or fire hazard Vent hood Combinations It is recommended that these rangetops be installed in conjunction with a suitable overhead vent hood e Install a hood with at least 1200 CFM above a 48 wide rangetop e Install a hood with at least 600 CFM above a 36 rangetop Due to the high heat capacity of this unit particular attention should be paid to the hood and ductwork installation to assure it meets local building codes WARNING Do nat install this product with an air curtain hood or other range hood that operates by blowing air down on the cooktop This airflow may interfere with operation of the gas burners resulting in fire or explosion hazard Clearances to horizontal surfaces above the range measured to the cooking surface are below Failure to comply may result in fire hazard Installations without a hood require 48 minimum to combustibles e A custom hood installation with exposed horizontal combustibles surfaces must have an Auto On feature e For other installations with a hood refer to hood installation instructions for specific hood clearances CAUTION These rangetops are extremely heavy Due to the weight and size of the rangetop and to reduce the risk of personal injury or damage to the product TWO PEOP
22. ve these two Screws The two outer screws are leveling screws Do not remove these two screws They can be turned to level the griddle or to provide a forward slope to help grease and oils to drain away from the food being cooked After leveling the griddle hand tighten the clamping screws do not over tighten INSTALLATION CHECKLIST E Make sure all controls are left in the OFF position E Make sure the flow of combustion and ventilation air to the rangetop is unobstructed M The serial plate for your rangetop is located on the bottom of the rangetop In addition to the model and serial numbers it tells you the ratings of the burners and the type of fuel and pressure the rangetop was adjusted for when it left the factory E Recheck Steps Double check to make sure everything in this manual has been completed Rechecking steps will ensure safe use of the rangetop ZX12B30PSS ZX12B36PSS ZX12B48PSS Accessory Installation OPTIONAL ACCESSORIES 12 HIGH BACKSPLASH WARNING To prevent ignition of combustible materials the entire back wall above the range must be protected by a backsplash constructed of non combustible material This stainless steel backsplash accessory must be installed in combination with a custom non combustible backsplash built beyond the 12 height of the backsplash Read these instructions completely and carefully IMPORTANT Save these instructions for local inspector s use I
23. wall with 4 wood screws Wood secure the SCreWS bottom panel to the wall with 4 wood Screws ZXADJB30PSS ZXADJB36PSS ZXADJB48PSS Accessory Installation INSTALL COVER PANELS See alternate method if side access is blocked e Hold the bottom cover over the bottom support while driving one screw provided into each side e Place the top cover with shelf over the top wall support If you have access to the sides secure the panel with two screws on each side e Secure the top cover with shelf to the top support with screws through the front of the panel at the top corners Use one screw on each side 14 INSTALL COVER PANELS cont ALTERNATE METHOD When side access is blocked e Install bottom cover over the bottom support while driving one screw into each side e Hold top cover in place while marking screw locations just below shelf support and onto bottom cover e Remove the shelf and drill a 9 64 diameter hole in the pencil marked locations e Mount the top cover over the top support and secure the front cover with screws through the drilled holes on each side e Install screws through each top corner Mark Screw Locations for Alternate Method Install Screw X on Each Si A Installation Convert Natural Gas to LP Gas Operation n stru cti ONS Convert LP Gas to Natural Gas Operation CONVERT THE REGULATOR Disconnect all electrical power at the main circuit
24. weight of the rangetop ee ailable i Backsplas Allow Additional Clearance Below the Rangetop Burner Box for the Regulator and Gas Connections 4 36 wide models are designed to fit in 36 or wider base cabinets Cutout Opening with False Bottom Dimensions oa s Pepo e You can construct the cutout with a false bottom to conceal the bottom of the rangetop Build the false bottom using a solid material cut a 7 1 2 x 11 1 8 hole in the left rear corner for the gas inlet and power cord clearances Installation STEP 2 INSTALL RANGETOP Slide the rangetop into the opening Make sure the rangetop is evenly seated and supported eA hold down strap with screws is provided to secure the rangetop to the rear or side cabinet walls e Remove the hold down strap from the back of the rangetop Attach one end of the strap to the back of the rangetop Secure the other end of the strap as high as possible to the cabinet back wall or adjacent cabinet Keep the strap as short as possible for better security STEP 3 CONNECT RANGETOP TO GAS WARNING Do not use a flame to check for gas leaks manual shut off valve must be installed where it will be accessible Assure that gas is turned off at the shut off valve e Install the supplied pressure regulator onto the end of the gas inlet eYou can install a 90 elbow not provided onto the gas inlet and route the gas connections to avoid interfe
Download Pdf Manuals
Related Search