Sharp SMD3070AS Installation Guide
Contents
1. be sure that the screws do not penetrate electrical wiring or plumbing Anti Tip block Figure 8 ELECTRICAL OUTLET The electrical requirements are a 120 volt 60 Hz AC only 15 amp or more protected electrical supply It is recommended that a separate circuit serving only this appliance be provided The drawer is equipped with a 3 prong grounding plug It must be plugged into a wall receptacle that is properly installed and grounded Should you only have a 2 prong outlet have a qualified electrician install a correct wall receptacle Note If you have any questions about the grounding or electrical instructions consult a qualified electrician or service person Can also be installed using an electrical outlet in an adjacent cabinet within the area where the provided electrical cord can reach Always check electrical codes for requirements Suggested electrical outlet location Figure 9 GROUNDING INSTRUCTIONS This appliance must be grounded The Microwave Drawer is equipped with a cord having a grounding wire with a grounding plug It must be plugged into a wall receptacle that is properly installed and grounded in accordance with the National Electrical Code and local codes and ordinances In the event of an electrical short circuit grounding reduces risk of electric shock by providing an escape wire for the electric current NGI E Improper use of the grounding plug can result in a risk of electric s2. 30 cabinet minimum P 15 9 16 opening Figure 5 a a 21 5 8 4 11 16 1 3 4 21 7 8 29 7 8 15 7 8 14 19 32 1 9 64 door thickness 15 auto drawer opening 4 ce rot on o gt Figure 6 This drawing represents a typical standard cabinet If installed in custom cabinets with extended counter tops take into account visibility and access to controls See Figure 7 A Move oven location downward for extended countertops B lt a Extended countertops l 11 lt E C Figure 7 D y G A 25 B 1 2 C 15 7 8 D 36 E Control panel shown in open position F 24 G 34 1 2 F ANTI TIP BLOGK NORMAL INSTALLATION STEPS ANTI TIP BLOCK INSTALLATION INSTRUCTIONS To reduce the risk of tipping of the drawer the Anti Tip block must be properly installed located 14 1 3 16 inches above the floor on which the Microwave Drawer will sit The 6 inch Anti Tip block must be provided by the installer See Figures 1 4 and 5 The Anti Tip block prevents serious injury that might result from spilled hot liquids If the Microwave Drawer is ever moved to a different location the Anti Tip block must also be moved and installed When installed to the wall make sure that the screws completely penetrate the dry wall and are secured in wood or metal so that the block is totally stable When fastening
3. S AND DIMENSIONS e Dimensions that are shown in Figure 1 for 24 or Figures 4 and 5 for 30 must be used Given dimensions provide minimum clearance Locate electrical outlet in the shaded area in the upper left hand corner of the cutout See Figure 9 Contact surface must be solid and level Pay special attention to the floor on which the Microwave Drawer will sit The floor of the opening should be constructed of plywood strong Your oven can be built into a cabinet or wall by itself or under a gas or electric wall oven Be sure that the clearance of the floor between the wall oven and the microwave drawer is a minimum of 2 inches The microwave interior will easily accommodate a 9 x 13 oblong dish or a bag of microwave popcorn The oven can also be mounted flush Please see instructions enough to support the weight of the oven about 100 pounds OGG for flush mounting included with the Flush Mount Deflector e Check location where the Microwave Drawer will be v nt installed for proper electrical supply 24 MICROWAVE DRAWER MEASUREMENTS ee ae a E Figure 2 ay one a A 21 5 8 F 15 7 8 B 4 11 16 G 14 19 32 Cutout Dimension 22 1 8 x 15 9 16 CIs E D 21 7 8 I 15 auto drawer opening 6 E 23 7 8 J 4 Suggested electrical outlet location Anti Tip block a Figures 1 and 2 contain many Microwave Dr
4. SHARP Microwave Drawer SMD2470AS SMD3070AS INSTALLATION MANUAL SPECIAL WARNING INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER IMPORTANT SAVE this installation manual FOR LOCAL ELECTRICAL INSPECTOR S USE READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE CLEARANCES AND DIMENSIONS For SAFETY CONSIDERATIONS do not install drawer in any combustible cabinetry which is not in accord with the stated clearances and dimensions on pages 2 5 See Figure 1 for 24 or Figures 4 and 5 for 30 UNPACKING YOUR MICROWAVE DRAWER e Remove all packing Sealing materials from inside surface the Microwave Drawer DO NOT REMOVE THE WAVEGUIDE COVER which is located on the top of the Microwave Waveguide Drawer _ Sealing e Remove the feature surface sticker if there is one Check the drawer for ale oe Oven cavity any damage such as misaligned or bent drawer damaged drawer seals and sealing surfaces broken or loose Microwave Drawer guides and dents inside the cavity or on the front side of the drawer If there is any damage do not operate the Microwave Drawer and contact your dealer or a SHARP AUTHORIZED SERVICER IMPORTANT NOTES TO THE INSTALLER e Read all of the Installation Manual before installing the Microwave Drawer e Remove all packing material before connecting the electrical supply e Observe all governing codes and ordinances e Be sure to leave these instructions with the co
5. awer measurements r a for reference when planning the drawer s location This Microwave Drawer can be installed below any electric or 22 1 8 opening gas wall oven 14 13 16 to bottom of Anti Tip block Allow 7 8 overlap Canalso be installed using an electrical outlet in an adjacent cabinet within the area where the provided electrical cord can reach Power cord access hole in cabinet should be a minimum 1 1 2 diameter hole and deburred of all sharp edges LU Always allow sufficient power cord length to the electrical outlet to prevent tension 23 1 2 minimum depth Allow 3 16 overlap 36 countertop height Allow 7 16 minimum overlap Floor must support 100 Ib 24 cabinet minimum Always check electrical codes for requirements NOZZrPASHMTAMmmMoOaA gt 15 9 16 opening This drawing represents a typical standard cabinet If installed in custom cabinets with extended counter tops take into account visibility and access to controls See Figure 3 A Move oven location downward for extended countertops B a Extended countertops i P E C Figure 3 D G A 25 B 1 2 C 15 7 8 D 36 E Control panel shown in open position F 24 G 34 1 2 n y F 30 MICROWAVE DRAWER MEASUREMENTS Figures 4 5 and 6 contain many Microwave Drawer measurements Can also be installed using an electrical outlet in an ad
6. hock Do not use an extension cord If the power supply cord is too short have a qualified electrician or serviceman install an outlet near the appliance Permanent and Correct Installation 3 Prong plug i a Sar A Grounding pin 3 Prong receptacle Grounded receptacle box DRAWER INSTALLATION 1 Place the drawer adjacent to the wall or cabinet opening Plug the power supply cord into the electrical outlet 2 Carefully guide the drawer into the prepared opening Avoid pinching the cord between the oven and the wall Parts supplied 3 Slide the drawer all the way until the mounting flange is flush with the face of the cabinet See Figure 10A g 4 Screws 4 Open the drawer Using the 4 holes on the drawer as a Figure 10B template pre drill the cabinet using a 1 16 bit See Figure 10A 5 Secure the drawer with the 4 screws supplied See Figure Figure 10A 10B MODEL AND SERIAL NUMBER LOCATION The name plate includes model and serial number Open the Microwave Drawer fully The label is beyond the back wall of the microwave cavity facing up from the flat surface CARE CLEANING AND MAINTENANCE Refer to the Operation Manual for cleaning instructions BEFORE YOU CALL FOR SERVICE Read the BEFORE YOU CALL and operating instruction sections in your Operation Manual It may save you time and expense The list includes common occurrences that are not the result of defective workmanship or materia
7. jacent for reference when planning the drawer s location cabinet within the area where the provided electrical cord can i i reach Power cord access hole in cabinet should be a minimum This Microwave Drawer can be installed below any electric or il 1 1 2 diameter hole and deburred of all sharp edges gas wall oven ee Always allow sufficient power cord length to the electrical outlet to prevent tension Always check electrical codes for requirements Cutout Dimension 28 7 16 x 15 9 16 A 84 wall cabinet B Optional wall oven cutout illustrated in sketch C Suggested electrical outlet location D 6 E Anti Tip block F 3 1 2 G 5 H 4 I 2 minimum J 28 7 16 opening K Allow 3 16 overlap L 14 13 16 to bottom of Anti Tip block M Allow 3 4 overlap N 23 1 2 minimum depth O 15 9 16 opening P Allow 7 16 overlap Q Floor must support 100 Ib R 30 cabinet minimum es R ia Te Figure 4 Cutout Dimension 28 7 16 x 15 9 16 6 Suggested electrical outlet location Anti Tip block 5 3 1 2 4 28 7 16 opening 14 13 16 to bottom of Anti Tip block Allow 3 4 overlap 23 1 2 minimum depth Allow 3 16 overlap 36 countertop height M Allow 7 16 overlap N Floor must support 100 Ib rAT TI TaADMmMOA Dp O
8. ls in this range Mounting flange Refer to the warranty in your Operation Manual for Sharp s toll free service number and address Please call or write if you have inquiries about your microwave product and or need to order parts SHARP SHARP ELECTRONICS CORPORATION 1 Sharp Plaza Suite 1 e Mahwah New Jersey 07495 1123 1 800 BE SHARP 237 4277 TINSEB539MRRO FEB 10 2015 8
9. nsumer IMPORTANT NOTES TO THE CONSUMER Keep this manual with your Operation Manual for future reference e As when using any microwave oven generating heat there are certain safety precautions you should follow These are listed in the Operation Manual Read all and follow carefully e Be sure your Microwave Drawer is installed and grounded properly by a qualified installer or service technician IMPORTANT SAFETY INSTRUCTIONS NENIT if the information in this manual is not followed exactly a fire or electrical shock may result that could cause property damage personal injury or death NNN To reduce the risk of tipping the Microwave Drawer must be secured by a properly installed Anti Tip block e This Microwave Drawer must be electrically grounded in accordance with local codes e Make sure the wall coverings and the cabinets around the Microwave Drawer can withstand the heat generated by the Microwave Drawer NONIM Never leave children alone or unattended in the area where a Microwave Drawer is in use Never leave the drawer open when the microwave is unattended AAWARNING Stepping leaning or sitting on the drawer may result in serious injuries and can also cause damage to the Microwave Drawer e Do not use the Microwave Drawer as a storage space This creates a potentially hazardous situation e Check that the time of day is in the display If not touch STOP CLEAR to prevent unintended use CLEARANCE
Download Pdf Manuals
Related Search