Extron electronic Extron Electronics Projector Accessories PMK 150 User's Manual
Contents
1. PMK 150 e Installation Guide The Extron PMK 150 Pole Mount Kit is a Gait Pipe Clamp simple solution for mounting Extron devices 5 S and their external power supplies to a projector pole The PMK can be installed on a 1 2 inch pipe within a 4 inch space between the projector TE and the ceiling 2 Hex Bolts K Y 2 Washers K Including the power supply the J following devices can be mounted 4 Pe Tie Wraps e one three inch deep half rack device or e two 3 inch deep quarter rack devices or Figure 1 PMK 150 Parts e an MPA 401 Figure 1 shows the parts that are included in the kit CAUTION The maximum load for the PMK 150 is 5 Ibs 2 25 kg NOTE The PMK 150 is to be used only with Extron UL listed products Installation NOTE Ensure the finished installation is in accordance with local and national building codes fire and safety codes UL requirements and local and national electrical codes To install the PMK 150 with a device on a projector pole 1 Place the plate on the base of the device and align holes in the plate with the mounting holes in the device see figure 2 2 Secure the device to the plate with 4 40 2 4 40 x 3 16 screws see note below Screws CAUTION Use only the screws supplied with the device to avoid damaging it NOTE When installing the MPA 401 onto the PMK 150 install it with the rear panel facing the projector pipe Allow enough space for the con2. nectors on the cables to fit without bending the i N P A holes on opposite corners cables excessively If the space for this is inadequate turn the MPA 401 around and place it on the PMK so the front panel of the device is closest to the pipe and then connect the cables Figure 2 Attaching the Device Continued on side 2 PMK 150 e Installation Guide continued 3 Attach the power supply to the underside of the mounting plate by passing the supplied tie wraps under the power supply through the raised slots in the plate and back over the power supply Ensure the tie wraps sit in the grooves on the power supply Tighten the ties until snug 4 With the installed device uppermost lift the plate up to the installation location on the projector pipe Fit the pipe clamp around the pipe and hold it against the flange on the mounting plate Figure 3 Attaching the Power Supply Insert the two hex bolts through the clamp holes and into the flange 6 Level the plate and tighten the hex bolts firmly to secure it against the pipe Half Rack Device Figure 4 Half Rack Device left and an MPA 401 right Mounted on the PMK 150 7 Attach input and output cables to the mounted device and thread them through the access hole in the projector pipe to the inputs and the display device Use the remaining tie wraps for cable tidying CAUTION DO NOT thread the power cable through the projector pipe Threading
3. the power cable through the pipe violates national electrical regulations 8 Connect the power supply to an electrical outlet and turn on the device For configuration and operation see the user guide for the device Extron USA West Extron USA East Extron Europe Extron Asia Extron Japan Extron China Extron Middle East Headquarters a 800 633 9876 800 3987 6673 800 7339 8766 81 3 3511 7655 400 883 1568 971 4 2991800 800 633 9876 Inside USA Canada Only Inside Europe Only Inside Asia Only 81 3 3511 7656 FAX Inside China Only 971 4 2991880 FAX Inside USA Canada Only 1 919 863 1794 31 33 453 4040 65 6383 4400 86 21 3760 1568 1 714 491 1500 1 919 863 1797 FAX 31 33 453 4050 FAX 65 6383 4664 FAX 86 21 3760 1566 FAX 68 1842 01 1 714 491 1517 FAX Rev A 2010 Extron Electronics All rights reserved www extron com 11 10
Download Pdf Manuals
Related Search