Bullet Tools 613 Instructions / Assembly
Contents
1. 7 MOUNT TO STAND OR CUT STATION Hook square bracket tem 9 under the lower flange of the base Set shear in place on chopsaw stand or on a pair of fastened 2x2s 38mm X 89mm spaced 24 5 622mm apart and bolt or lag into place Bolts and lag screws not included MAKING CUTS The Magnum Siding Shear is operated manually The two part extendable handle is grasped by the operator and pushed down to make a cut IVE EXTREME CAUTION Blade is very sharp CUTTING 1 Unlock safety lock by sliding knob over and down 2 Insert material It is recommended that you HOLD MATERIAL IN PLACE until the cut is complete yiN Always keep hands away from blade 3 PUSH HANDLE DOWN TO CUT Some effort may be required depending on hardness of material b 4 CAUTION Handle is spring loaded DO NOT ALLOW i _ HANDLE TO SLAM BACK AFTER MAKING A CUT SAFETY LOCK For maximum security the safety lock will automatically reset in the locked position unless disengaged The safety lock can be disengaged by sliding the knob over and down hooking into slot Shown Right TRANSPORT It is important to re engage lock and secure unextended handle in down position while storing carrying or transporting your Magnum Siding Shear TIP DOUBLE CUTTING Most materials listed on p 11 shear very well with just one cut However some brands of fiber cement siding and other products may require cutting twice to prod2. Provides a sturdy raised platform for use or display Mounting bracket included with your Magnum Siding Shear ALL ANGLE FENCE 701AF Sets to any angle from 0 to 90 degrees O SLICKSHOT 701SL Dry lubricant for the Magnum Siding Shear LASER REPLACEMENT 900 LAS RP LASER BATTERIES 900 BAT RP Replacement batteries for your laser Your Magnum Siding Shear cuts a wide variety of products Please refer to this cut guide for recommended products and thicknesses Magnum Siding Shear CUT GUIDE Maximum Thickness 25mm or 1 Material Siding Fiber Cement Board Siding Pressboard Lap Siding Wood Trim OSB Trim Fiber Cement Trim Vinyl Shingles Tar or Wood Commercial Vinyl Luxury Vinyl Tile Parquet Laminate Flooring PVC Tile Rubber Cove Base Rubber Tile Soft Plastic Please note Approved materials may vary in density and hardness If extreme pressure is required to cut a product it may result in damage to your machine Please contact Bullet Tools before proceeding Warranty is void if an unapproved product damages the machine 10 WARRANTY 30 Day Satisfaction Guarantee Bullet Tools is confident that you will be absolutely pleased with the purchase of our product If for any reason you are not completely satisfied with your tool we will refund your purchase price at any time within 30 days of your original purchase receipt required If you want to return your pro
3. O HONE There are three situations when it is very important With the blade in the machine it is quick and to hone the blade remove burrs on the flat side of easy to hone Simply pull the Magnum Siding the blade Shear handle down until the blade is just above the blade stop approximately 1 8 Then lay 1 After the first 30 100 cuts on a new blade the wide flat side of the hone stone against the 2 Every 100 cuts on the job flat side of the blade and move hone stone from 3 When the blade has been re sharpened end to end 2 to 3 times to remove any burrs Use Hand Protection Blade is very sharp Note It is not necessary to remove the small nicks or chips from the blade edge when sharpening or honing SHARPENING THE BLADE The blade can be sharpened to restore a one side 21 22 knife edge It is important to note that the blade must be sharpened only on the beveled side leaving the flat side flat We recommend that power grinding only be done professionally as the blade must be fluid cooled during this process Flat Side Table Side ADJUSTING THE BLADE Your Magnum Siding Shear is equipped with adjustment jack screws see pic on next page for fine tuning the angle of your blade or compensating for small blades Blades shrink every time they are re sharpened To tilt your blade turn the machine upside down as when removing the blade loosen but don t remove the Item D screws Adjust t
4. SER GUIDE Read Before Use AGN amp Ve iw HA Iii WA a f f ill Applies to Model Numbers 613 amp 620 b TM ULLEI IVUL Cutting Edge Solutions for Tradesmen Ka 3 aa D Py vi KI mS SSA SGPT Dy NY N OR PRT INS O0600Rev A 12 13 2013 Bullet Tools www BulletTools com 208 772 0175 WARNING FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS INJURY Using This Machine With Respect And Caution Will Considerably Reduce The Risk Of Personal Injury Oo NAM BR Ww 10 11 12 13 14 15 16 SAFETY RULES FOR THE MAGNUM SIDING SHEAR Read and understand this instruction manual before operating the Magnum Siding Shear If you are not thoroughly familiar with the operation of the Magnum Siding Shear obtain advice from a qualified instructor or call 800 406 8998 Stay alert Do not operate while under the influence of drugs alcohol or medication Always wear safety approved eye protection with side shields ANSI Z87 1 Keep work area clean and free of debris Keep children and unauthorized persons away from the Magnum Siding Shear and work area Make sure tool is secure Operate only on a firm substrate or solid stand Use the right tool Do not force the Magnum Siding Shear or use it for a job for which it was not designed use only on approved materials Keep blade sharp A dull blade will not perform properly Al
5. alled in Cam The Hardware Kit is used in 3 multiple models Your Shear may Item G 1 10mm Hex Wrench Not Shown sonucaaall gE heran CE 2 ATTACH TAIL 1 ATTACH RAILS Attach tail and angle brackets to rails using Item C machine screws Make sure holes in tail are facing up Attach rails to base using Item A machine screws fitted with star washers Item B 3 ATTACH TABLE A Attach table to base starting with front start screws with hand using Item D machine screws B Attach back of table to tail using Item E self tapping screws sche Stop AEN aa 4 ATTACH HANDLE Insert handle into cam shaft Note Backstroke Stop must face upward Tighten tem F Bolt pre installed in cam shaft with 10mm hex wrench Item G Included Note Do not remove plastic tie and orange tag until handle is bolted in place Cam Shaft M16 x 50 Bolt 5 PLACE THE FENCE Insert fence into one of the six hole sets on the table there are two 90 and four 45 locations The fence is friction fit requires effort to insert or remove ON Button 6 ALIGN LASER To adjust laser line projection angle turn on laser by pushing the red button Loosen but do not remove laser attachment screw M4x12 PHP by 4 to 5 full turns Firmly press on sides of laser barrel with two fingers of each hand Rotate laser barrel until desired alignment is achieved Tighten the laser attachment screw snugly
6. duct under our 30 day no risk trial offer valid only for purchases made in the US please contact us at 1 800 406 8998 or 208 772 0175 for return instructions BULLETPROOF WARRANTY GOLD 5 Year Bullet Tools warrants only to the original purchaser of this product when purchased from an authorized reseller or distributor that this product will be free from defects in material and workmanship under normal use and service for five 5 years from initial purchase This warranty includes all parts except the blade and cosmetic appearance chips dings scratches caused by normal use and wear This warranty does not cover any damage due to accident misuse abuse or negligence Further it is valid only if the product is used with the cut products specified in the cut guide Please refer to the User Guide for details or call Bullet Tools technical support In order to recover under this limited warranty the purchaser must make claim to Bullet Tools within 60 days of occurrence and must present acceptable proof of original ownership such as original receipt warranty card registration on line registration or other documentation Bullet Tools deems acceptable for the product Bullet Tools at its option shall repair or replace the defective unit covered by this warranty Bullet Tools disclaims all warranties express or implied including all warranties of merchantability and or fitness for a particular purpose Additional r
7. he jack screws to desired position with 5 32 or 4mm Allen wrench MAINTENANCE CHANGING THE BLADE WARNING Blade is extremely sharp Use hand protection when removing honing or sharpening blade 1 TURN SHEAR UPSIDE DOWN Tip put the shear on the edge of a sturdy table 2 LOOSEN BLADE Using a Phillips screwdriver remove the Item D Screws 3 REMOVE BLADE Hold blade by each end and carefully lift out of pocket 4 INSTALL BLADE Hold blade by each end and carefully place into the blade pocket in the head with the flat side of the blade facing the table Be sure that it is firmly seated and the pocket is clear of debris 5 TIGHTEN THE BLADE Using a Phillips screwdriver replace amp tighten the screws Starting with the center screw Hold by ends LUBRICATING It is important to spray a fine layer of Slick Shot lubricant over the power assembly at the points indicated Shown Left once every month Wipe down with WD40 or a light machine oil to prevent corrosion THE BLADE STOP The blade stop may become worn Remove anvil turn blade stop over for more use Replacements can be purchased at your dealer Page 3 AVAILABLE ACCESSORIES REPLACEMENT BLADES 13 Siding Blade 20 Siding Blade 13 All Purpose Premium Blade 20 All Purpose Premium Blade HONE STONE Keep your blade honed for longer use SHEAR STAND 709
8. ights may be available under the laws of your state or province Any and all warranties written or implied are void with any alterations to the product Note Bullet Tools shall not be liable for any special incidental or consequential damages including but not limited to lost revenue lost profits rental or replacement equipment downtime damage to property and third party claims arising out of any theory of recovery including warranty contract statutory or tort To obtain warranty service please contact Bullet Tools at 1 800 406 8998 or 1 208 772 0175 for pre authorization and further instructions
9. uce a better cut Simply make your first cut 1 8 to 1 4 3 to 6mm longer than your mark then go back and make your second cut on your mark This is very useful to create a cleaner cut when a trim molding or transition cannot be used to cover your cut end CUSTOM SETTINGS Set to cut over 3 4 BACKSTROKE STOP ae am To cut approved products over 3 4 19mm thick loosen Phillips head screw on the Backstroke Stop turn the Backstroke Stop 180 and tighten screw For more convenience when cutting thinner products restore factory setting THE ANVIL The Anvil has two edges a 1 32 0 75mm narrow edge and a 3 16 4 5mm wide edge Either edge can be used according to the support needed to make a clean cut Some soft backed products require the wider anvil edge TO CHANGE BETWEEN ANVIL EDGES Simply remove the anvil screws and flip the anvil over Ensure blade stop is in place BLADESTOP BLADESTOP CUTTING DEPTH You may need to adjust the height of the blade to cut all the way through your product You can do this by ADJUSTING THE STOP SCREW 1 Loosen the stop screw nut and turn stop screw until it is loose Release handle to open blade 2 Push the handle down until the blade is resting on the blade stop 3 Adjust the stop screw until it makes contact with the power assembly LASER REALIGNMENT See page 5 step 6 MAINTENANCE WHEN TO HONE T
10. ways keep hands away from blade while operating or carrying Do not alter or misuse this tool The Magnum Siding Shear is precision built modifications not specified in this manual may result in a dangerous condition Maintain Magnum Siding Shear with care Keep blade sharp and clean Follow instructions for lubricating and changing accessories Use only recommended accessories The use of improper accessories may cause hazards or injury Never leave the Magnum Siding Shear unattended Secure the handle with the safety lock when not in use Warning The dust generated by cutting certain wood wood fiber fiber cement and or PVC products can be injurious to your health Bullet Tools does not endorse or warrant inferior knock off imitations of our designs Using these may be dangerous please contact the manufacturer about any defects with these S ET U D You will need 2 amp 3 Phillips head screwdrivers Please Review and Verify Parts Included in Box Power Assembly Handle Assembly Fence Table Tail Rails 2 e Hone Stone i Angle Bracket Square Bracket 10 HARDWARE KIT OO NANAWHN HARDWARE KIT Item A 4 8mm x 60mm PH Phillips Machine Screws Item B 4 M8 Star Washers Item C 4 8mm x 25mm PH Phillips Machine Screws Item D 6 6mm x 16mm PH PHillips Machine Screws Item E 5 10 x 1 PH Phillips Self Tapping Screws AAUMUULLLIIUUL LIIN Item F 1 M16 x 50 BHCS Pre inst
Download Pdf Manuals
Related Search