Typar XHWTPFLRA1-003 Installation Guide
Contents
1. 152 mm vertically and horizontally Ensure proper shingling throughout the installation to properly shed water Once the structure is completely covered tape all seams and penetrations using Typar construction tape Please refer to the Typar flashing instructions for more detailed instruction on penetrations and window flashing installation STEP 4 After the installation complete and before the exterior cladding is installed inspect the Typar for tears Repair the issues with Typar Construction tape or Typar Flashing Made in the U S A Fiberweb Inc e mma 70 Old Hickory Blvd Fiberweb Old Hickory TN 37138 USA 1 615 847 7000 Fax 1 615 847 7068 www Typar com Tilt wall Installation Weather Protection S siem Install Typar HouseWrap over an approved exterior sheathing after the framing is complete and before the windows and doors have been installed Plastic capped fasteners should be used and spaced at 32 OC vertically and horizontally when being applied over 7 16 OSB or 15 32 plywood When installing over metal framing use screws with washers STEP 1 Begin with the wall lying on the ground Start at one corner allowing an extra 12 304mm flap for the corner and align the guide marks on the Typar with the studs Ensure a 6 excess flap on one side to allow for overlap to the next wall section Fasten Typar to the wall at 32 both horizontally and vertically STEP 2 When sta2. gt Tbn Made in the U S A Fiberweb Inc m 70 Old Hickory Blvd Fiberweb ernie DerEeTTeT 1 615 847 7000 Fax 1 615 847 7068 www lypar com TYPAR Weather Protection S siem Flashing Arched Windows STEP 1 Start with the Typar Flashing Flex cut a piece that is 12 longer than the length of the rough opening window sill Carefully pull off the release liner Center the Flashing in the center of the rough opening and work your way toward the corners and then up the sides Note the flex flashing should overlap to the outside of the wall by 2 3 Only stretch the flashing in the corners If needed secure the fanned edges of the Typar Flashing Flex with a plastic capped nail staple STEP 2 Apply a continuous bead of sealant to the back of the window or on the wall Do not apply the sealant across the bottom of the sill or on the bottom of the window This area is left open to allow for proper drainage Install the window according to the manufacturer s installation instructions STEP 3 Cut two pieces of Typar Flashing long enough to extend 1 above the window head flange and 1 below the window sill flange Carefully peel off the release liner and apply the flashing on both sides of the window Make sure to cover the entire window mounting flange press firmly either by hand or using a J roller Ensure there are no wrinkles or bubbles For the head flashing cut a piece of Typar Flashing Flex 12 l
3. TYPAR Weather Protection S siem TYPAR Weather Protection System Installation Instructions Made in the U S A Fiberweb Inc m 70 Old Hickory Blvd Fiberweb Old Hickory TN 37138 USA 1 615 847 7000 Fax 1 615 847 7068 www Typar com Weather Protection System Code Requirements The 2006 international building code IBC and the 2006 International Residential code IRC require a water resistive barrier equivalent to ASTM D226 Type 1 15 felt be installed behind the exterior cladding Typar HouseWrap exceeds these standards Approvals and Reports ICC ESR 1404 CCMC 12892 R amp 12884 R Typar HouseWrap meets AC38 standards Acceptance Criteria for Water Resistive Barriers Typar Flashing products meet the requirements for AAMA 711 Recommended Materials e Typar HouseWrap e Typar Construction tape e Typar RA flashing e Typar BA flashing e Typar Flex flashing Product Size Data Weather Resistive Barriers Size Rolls Pallet Typar HouseWrap 3 x 100 144 3 4 x 100 4 6 x 200 32 9 x 100 40 9 x 150 36 9 x 195 32 9 6 x 95 40 10 x 100 40 10 x 150 36 Accessories Size Rolls Case Typar RA Flashing A x 75 9 6 X75 6 9 x 75 4 12 x75 3 Typar BA Flashing 4 x 75 12 6x75 6 9 x 75 4 Typar Flashing Flex 6 x 75 3 9 x 75 2 Typar Construction Tape 1 7 8 x 165 Typar Construction Tape Canada 60mm x 66m 24 Made in the U S A Fiberweb In
4. c ma 70 Old Hickory Blvd Fiberweb Old Hickory TN 37138 USA 1 615 847 7000 Fax 1 615 847 7068 www Typar com TY PAR Weather Protection oy stem Table of Contents PO CIS aca ates ostos tection ase ie costa Sioesa gen beina EE E A 2 SDECIG INSTAIIGHOR Considera ONS svesisusoncsaunsasdeusinoan en venaphncsenscsivdeaveavebswiepandsneadsas davlesiatsdbddgersaviebseniswsnesaisesdebidulncdwlssswebeamveendpindiebe 2 CS VOI ONEEN A vn tec stearic paca stake ed va te E EAN vande ae AT EE E NE N ENEE NE E E E EET 3 Approvals and Repris aiseria a E A EAE AEAEE EEE AEAEE EET E Aa 3 Recommended IVE CIN Gace anaE E E Meas EE ETA EEE EONA TENA 3 Produc SE DO a E E E ATT E E E 3 Veruca wal InstalatiO cz c ccnatcecacssaretasacatecetnnintt a a a a A a a i 4 TA WO TSN ONO AENA EAEN A S E E O EA A N A EE A E ET AT A E ee 5 Window and Door Preparation sinsivirussiiriiioetirins inini ia sda diced ta NENANA ANE EAA Sars eae E URR 6 Window Flashing General InstrUCtHONS ssasiceansanhapssianhesinnstennubasdaaspeansaensemastassiiwssbastanaanansavnesihexabiasteaianaoneasomnsannapsblanhesieansdanssenssensdeneas 7 Epa ae AA aA A e AAEE E T EE E A A AE E A I A A A E E A I E A 8 Flashning Arched WINOOWS pieces erstnats ten dusaantesnatsnueoanstosaustuiacatotentatcedseiudcenuetaiassadandtstnieteqesheianovanndeedsattadaeeaauieseuatexatossindceinetuticouenii 9 PSIG PROS easiness A acres intone cons A T E AA riod AEEA ATA EE A A AEEA OO 10 These instructions describe h
5. e Flashing in the center of the rough opening and work your way toward the corners and then up the sides Note the flex flashing should overlap to the outside of the wall by 2 3 Only stretch the flashing in the corners If needed secure the fanned edges of the Typar Flashing Flex with a plastic capped nail staple STEP 2 Apply a continuous bead of sealant to the back of the window or on the wall Do not apply the sealant across the bottom of the sill or on the bottom of the window This area is left open to allow for proper drainage Install the window according to the manufacturer s installation instructions STEP 3 Cut two pieces of Typar Flashing long enough to extend 1 above the window head flange and 1 below the window sill flange Carefully peel off the release liner and apply the flashing on both sides of the window Make sure to cover the entire window flange press firmly either by hand or using a J roller Ensure there are no wrinkles or bubbles Cut a piece of Typar Flashing for the head flashing Ensure that the piece is long enough to extend by 1 on both sides of the jamb flashing Remove the release liner and carefully install the flashing Cover the window flange and press firmly by hand or using a J roller STEP 4 Release the upper flap of the WRB that you cut earlier Tape the 45 degree cuts using Typar Construction Tape or Typar Flashing DO NOT tape the WRB along the top of the window flange Wane
6. make a vertical cut running two thirds of the way down the opening STEP3 From that stopping point cut diagonally to both lower left and right corners of the opening STEP 4 Pull each of the flaps tightly inside the rough opening and attach them to the frame with nails Staples or tape STEP 5 At the window header make a 6 diagonal cut at a 45 degree angle on both corners Fold the material up exposing the sheathing Now install the window or door according to the manufacturer instructions The final step is to flash all seams and flanges securely refer to Typar Flashing instructions Typar flashing should also be installed in accordance with window manufacturer instructions and according to the ASTM 2112 standard 1 2 3 4 5 Made in the U S A Fiberweb Inc gt ma 70 Old Hickory Blvd F ibe rweb Old Hickory TN 37138 USA 1 615 847 7000 Fax 1 615 847 7068 www lypar com Weather Protection S siem Window Flashing General Instructions Installations methods approved by the American Architectural Manufacturers Association AAMA are acceptable for TYPAR products and system warrantee Flashing products should always be installed on a dry surface that is free of dirt and debris Wipe surfaces to remove moisture grease and other contaminants that could interfere with adhesion Avoid placing fasteners where the Typar flashing will be installed however the fasteners can be installed over the flashing M
7. onger than the length on the window arc Carefully begin to peel of the release liner and installing the flashing to the contour of the window flange as you go The head flashing should overlap the jamb flashing by at least 6 If needed use button fasteners to secure the outer edges STEP 4 Flip down the WRB that you cut earlier Trim the WRB tight to the window arc if needed Tape the seams using Typar Construction Tape DO NOT tape along the window arc 1 2 y W N W js Mj Made in the U S A Fiberweb Inc gt ma 70 Old Hickory Blvd F ibe rweb Old Hickory TN 37138 USA 1 615 847 7000 Fax 1 615 847 7068 www lypar com TYPAR Weather Protection S siem Flashing Penetrations Penetrations such as exhaust fans exterior electrical outlets dryer vents exterior lights and gas outlets are a common entrance for bulk water into the wall cavity Using Typar flashing will ensure proper water hold out and maintain the integrity of the structure The method is similar to the flashing a window Start by flashing the bottom of the penetration Ensure to shingle the upper tape over the bottom tape Some penetrations have flanges such as dryer vents These penetrations should be flashed according to the details below 1 STEP 1 Install the vent according to the manufacturer s recommendations Trim the housewrap as close as possible around the perimeter of the vent STEP 2 Flash the vent using the same me
8. ost circumstances do not require you to prime the surface before installing Typar Flashing However some adverse weather conditions extreme temperatures or specialty installations such as concrete masonry or fiber face gypsum board may require a primer such as 3M or Super 77 to obtain optimal adhesion Install the primer according to the manufacturer s installation instructions The use of a heat gun will assist in adhesion during colder conditions Do not expose the flashing to direct sunlight for longer than recommended by the manufacturer Do not apply the flashing to a flexible vinyl surface although rigid PVC is acceptable Please check with the window manufacturer for compliance with rubberized asphalt flashing products For more information visit our website at www Typar com or contact your local Typar sales rep Tools Needed e Brush for surface preparation e Utility Knife or Scissors e Gloves e J Roller e Primer optional Made in the U S A Fiberweb Inc gt ma 70 Old Hickory Blvd F ibe rweb Old Hickory TN 37138 USA 1 615 847 7000 Fax 1 615 847 7068 www lypar com TYPAR Weather Protection oy stem Typical Window Flashing STEP 1 Install the window sill pan according to the manufacturer s instructions Alternatively you can create a sill pan using Typar Flashing Flex Cut a piece that is 12 longer than the length of the rough opening window sill Carefully pull off the release liner Center th
9. ow to install the Typar Weather Protection System for exceptional exterior water management For more detail on other Typar products please visit www Typar com Special Installation Considerations Stucco When stucco is installed over wood based sheeting the 2006 IBC section 2510 6 and the 2006 IRC section R 703 6 3 require a water resistive barrier with a performance at least equivalent to two layers of Grade D paper or a layer of water resistive barrier WRB which is separated from the stucco by an intervening layer When Typar WRB is used behind stucco it should be separated from the stucco by a second layer of Typar WRB a layer of Grade D building paper or the Grade D paper backing of paper backed lath Brick The 2006 IRC section R703 7 4 2 requires a min 1 25mm airspace separating the brick from the WRB The Brick Industry Association recommends a 1 25mm air space in front of the wood stud construction and a 2 air space in front of a steel stud construction Stone Veneer The 2006 IBC Section 1405 6 requires two layers of WRB behind stone Over wood frame construction Typar WRB should be installed behind stone the same way as installed behind stucco Wood Siding Typar WRB and wood siding must be installed according to the manufacturer s instruction and the industry standards Wood industry association recommends siding should be primed before installation Typar recommends tha
10. rting a new section fold the beginning side flap over the vertical stud and secure only one side After fastened trim the excess Typar Remember to allow enough so that the bottom excess overlaps the sill plate when the wall is put into place As each wall is put into place ensure that each side flap is on the exterior of the building Fiberweb g STEP 3 Secure the side flaps and the bottom flap using plastic capped nail or staples Typar tape and or a Non Silicone Caulk STEP 4 The second course of Typar should overlap the bottom sheet at least 6 152 mm Both vertical and horizontal seams ensure proper drainage by using the shingling method STEP 5 Tape all seems with Typar Construction Tape Please refer to the Typar flashing instructions for further detail STEP 6 After the installation is complete and before the exterior cladding is installed inspect the Typar for tears If issues are found tape the imperfections with Typar Construction Tape or Typar Flashing Fiberweb Inc 70 Old Hickory Blvd Old Hickory TN 37138 USA 1 615 847 7000 Fax 1 615 847 7068 www lypar com Weather Protection S siem Window and Door Preparation Preparing for Window Installation STEP 1 After wrapping the structure and covering all rough openings Cut a horizontal line across the top of the window opening The cut should not extend past the rough opening STEP 2 Start at the top center and
11. t the installation of any material must first follow the local applicable building codes Made in the U S A Fiberweb Inc gt mm 70 Old Hickory Blvd F ibe rweb Old Hickory TN 37138 USA 1 615 847 7000 Fax 1 615 847 7068 www lypar com a Weather Protection S siem Vertical wall Installation Install Typar HouseWrap over an approved exterior sheathing after the framing is complete and before the windows and doors have been installed Plastic capped fasteners should be used and spaced at 32 OC vertically and horizontally when being applied over 7 16 OSB or 15 32 plywood When installing over metal framing use screws with washers If the windows and doors have already been installed trim the Typar WRB close to the window frame and flash according to the Typar Flashing instructions STEP 1 Start at the bottom of one end of the wall with STEP 2 the printed side facing out When starting at a Fasten the Typar to the stud using plastic corner overlap by a minimum of 12 capped nails or staples at 32 O C both horizontally and vertically Place the housewrap roll horizontally and roll out the first course evenly covering rough window and door openings Allowing for a 2 4 51 102 mm overlap on the sill plate A Pull the Typar snug and avoiding wrinkles and creases Ensure that the product is level STEP 3 The upper layer of Typar housewrap should overlap the bottom layer by a minimum of 6
12. thod as windows Starting at the bottom flange cut the flashing so that it extends past the flanges by 1 on both sides Now apply the flashing to the 2 sides of the vent Remember to extend the flashing 1 on both top and bottom Make sure to smooth out wrinkles and air bubbles The use of a J roller is optional STEP 3 The Final step is to install the flashing across the top Extend the flashing out at least 1 on both sides Note This type of installation is suitable for several different penetrations Always use the 3 shingling method and ensure a tight seal around the flange penetration Typar HouseWrap is part of a complete Weather Protection System which also includes Typar Metro Wrap Typar Flashings and Construction tape For more information visit www Typar com Made in the U S A Fiberweb Inc gt ma 70 Old Hickory Blvd F ibe rweb Old Hickory TN 37138 USA 1 615 847 7000 Fax 1 615 847 7068 www lypar com
Download Pdf Manuals
Related Search