Wagner 0530010 Use and Care Manual
Contents
1. Practice Usage Scan this QR code with your mobile device and you will be directed to a video on Practice E and Usage tips IMPORTANT Make sure your floors and furnishings are covered with drop cloths during usage Break Periods During break periods the handle assembly should be placed flat with the roller sitting on a clean piece of cardboard or on top of the container During break periods make sure that the roller is not saturated with paint or it will drip and accumulate Avoid leaving the roller exposed to the sun or excessive heat during break periods During extended break periods more than 1 2 hour wrap the roller in a plastic bag to keep it from drying out Place it away from any heat sources and out of the sun Handle Button When the handle button is pressed and released the pump motor will turn on and material will begin flowing into the paint hose To shut the motor off and stop the flow of material press and release the handle button again Note Make sure to fully press and release the handle button If the handle button is only partially pressed the motor will start but will shut down again after the button is released IMPORTANT Do not submerge handle into any liquids and avoid getting any spillage around the handle button Practice Usage 1 Turn the ON OFF switch to ON 2 To start the motor fully press and release the handle button When paint st2. arts to show through the roller press and release the handle button to shut off the motor Tips e Practice rolling on a scrap piece of wood or cardboard Press the handle button to start and stop the pump as needed Wagner Spray Tech All Rights Reserved Prepping the Room Painting the Room Remove all pictures mirrors and decorations from Tip If you need more than one gallon of paint to do the walls and draperies from the windows Remove the room s walls mix them together to ensure color all nails hardware and switch and receptacle covers uniformity Cover furniture and floor with drop cloths Always make sure to open a window or door to ensure proper ventilation Surface Preparation fe a rer If you are painting both the ceiling and walls in Always remove wallpaper before painting Wask offoldadhesveand rinse withiwater your room start with the ceiling first and then AA move to the walls Allow the walls to dry before painting Wash and rinse dirt grease and oil build up off Ceilings the walls with soap and water e Paint across the short width of the ceiling Fill all nail holes joints and cracks with patching Walls paste Let dry and sand the surface until smooth Clean sanded area with a damp cloth Paint one wall at a time Spot prime all patched areas and any marker Pick an area to start where you can saturate and or pen marks before applying first coat the roller cover an
3. d evenly distribute the z R paint Working in three foot sections begin by Tip Write the important information from your cutting in around windows doors cabinets paint can color formula brand and paint type on base and other breaks in the wall surface the back of a switch plate for future reference Press and release the handle button until paint appears through the roller cover Start painting at one end of a wall and roll out the letter W Fill it in with crosswise strokes working your way across the wall in 3 x 3 sections Finish the sections by painting one solid swipe from ceiling to floor This will give you a nice even paint finish Press and release the handle button as needed for more paint Be careful not to over saturate the roller cover as it may drip slide on the wall or spatter Make sure to run the roller cover over the areas you cut in around the trim and baseboards to even out the texture If you need to stop and take a break finish painting the entire wall or stop at a break in the wall such as a doorway or corner to prevent lap marks Wagner Spray Tech All Rights Reserved 9 Scan this QR code with your E mobile device and you will be directed to a video on Cleanup m tips IMPORTANT Make sure your floors and furnishings are covered with drop cloths during cleanup You will need A waste container A minimum of one gallon of warm soap
4. hoses and roller arm Note Allow the pump to circulate the cleaning solution for about 10 minutes If desired refill the bucket with new cleaning solution and repeat for another 5 minutes 8 While unit is self cleaning disassemble the roller assembly and thoroughly clean the roller cover core and cap by hand Insert thumb to first knuckle pry and pull the cap from the roller cover Once the cap is removed push the core out the other end DO NOT throw away the core and cap Fully press and release the handle button to switch the motor off Remove suction tube from solution and run motor until all cleaning solution is purged from the unit Turn the switch OFF Unplug power cord Press quick release tabs and remove the roller arm from the roller handle Remove any remaining paint with the appropriate cleaning solution and a damp cloth IMPORTANT If you used mineral spirits to clean your unit you must repeat all the steps on this page using warm soapy water CLEANING SOLUTION Wagner Spray Tech All Rights Reserved
5. y water if you used latex paints A minimum of one quart of mineral spirits if you used oil based paints IMPORTANT DO NOT SUBMERGE THE ROLLER HANDLE INTO ANY LIQUIDS Notes Thoroughly cleaning your unit and its components is the best way to ensure the prolonged life of your unit A light paint film residue may remain in the paint hose after cleaning This is normal and will not affect the future performance of your unit Switch the unit OFF 0 prior to removing any accessories or components A Roller Cleanup Kit is available for separate purchase See Accessories page 44 for ordering information To Clean 1 Submerge suction tube into a bucket of the appropriate cleaning solution 2 Press locking tab and drop roller cover assembly into a bucket of the appropriate cleaning solution 3 Place the roller arm in the material container in order to catch paint 4 Turn the switch ON Fully press and release the handle button to switch the motor on Let the motor run for 15 seconds to push paint from the hoses back into the paint can Fully press and release the handle button to switch the motor off Wagner Spray Tech All Rights Reserved 5 Remove container from pump Leave suction tube submerged into the bucket of the appropriate cleaning solution Hang the roller arm from the bucket Fully press and release the handle button to run the appropriate cleaning solution through the
Download Pdf Manuals
Related Search