Home

Andersen HD20V36WH Installation Guide

image

Contents

1. 1 year after purchase are subject to a flat processing fee OOPS PROOF INSTALLATION LIMITED WARRANTY EMCO Enterprises Inc EMCO warrants that any part lost or mis cut during the original installation of your Andersen storm door will be repaired or replaced at no additional charge within ninety 90 days of the date of original purchase This limited warranty will not apply if the part has been misused abused or altered Cutting parts not specified by the installation guide or mis drilled parts are not included in this warranty In the event a part is lost or mis cut within the limited warranty period EMCO at its option will provide the appropriate replacement part installation is not included Please locate the door serial number and written proof of purchase and contact EMCO Consumer Support at 1 800 933 3626 GENERAL LIMITED WARRANTY INFORMATION The limited warranties set forth in this document are the only express warranties whether written or oral applicable to Andersen storm doors and no one is authorized to modify or expand these limited warranties All warranty claims must be made during the applicable warranty periods ALL IMPLIED WARRANTIES INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO THE APPLICABLE STATUTE OF LIMITATION BUT IN NO CASE WILL EXTEND BEYOND THE TERM OF THE LIMITED WARRANTIES SET FORTH ABOVE EMCO EXCLUDES AND WILL NOT PAY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES WHETHER ARISING O
2. 2 SS SSS LEFT HINGE INTERIOR Views RIGHT HINGE INTERIOR Views In this step you will install the bottom sweep components 1 Slide the sweep fin into the track located on the bottom of the door sweep Figure 24 2 Using scissors trim any excess sweep fin material that extends beyond the door sweep 3 Using pliers crimp each end of the track to prevent the sweep fin from coming out of the track See the close up showing the track as already crimped Figure 24 4 Open the door and slide the sweep onto the bottom of the door frame Make sure that the screw slots on the sweep are towards the interior 5 Position the door sweep so that it is flush with the latch side of the door frame Figure 25 6 Close the door 7 From the interior adjust the sweep up or down until the sweep fins lightly come into contact with the door sill 8 Using the drill and 1 8 drill bit drill a starter hole into the door using the pre drilled hole slots as guides CAUTION Do not drill completely through door This will create an unnecessary hole in the door and may cause water and air infiltration 9 Fasten the sweep to the door using two 2 8 X 1 2 color matched to sweep screws Figure 25 Figure 25 9 INSTALL CLOSER Tools needed AP S 5 32 2e 5 322 In this step you will install a jamb bracket onto the door jamb at the bottom Figure 26 1 Meas
3. WARNINGS AND CAUTIONS IN THIS GUIDE WARNING Aw WARNING Aw WARNING WARNING Entry door Improper use of hand Windows and doors The insect screen is Metal fasteners and other hardware components may hardware or power tools could can be heavy Use safe intended for reasonable corrode when exposed to preservative treated and and handle result in injury and or lifting techniques and insect control and not the _ fire retardant treated lumber Obtain and use the product damage a reasonable number retention of objects or appropriate size stainless steel fasteners and hardware Follow equipment of people with enough persons within the interior as called out by the installation guide to fasten unit manufacturer s strength to lift carry and The insect screen material to any rough opening made from pressure treated instructions for safe install window and door will not stop a person from and fire retardant treated lumber Failure to use the operation Always products to avoid injury falling through the door appropriate materials for the installation may cause a wear safety glasses and or property damage failure resulting in injury property or product damage RECOMMENDED TOOLS e Safety Glasses Drill e Drill Bits e Tape Measure e Square e Hammer _ 3 32 e 1 8 e 5 32 Py Scissors aE e Center Punch e Pliers e Screwdrivers e Pencil gt e Level _ 0 L VERIFY MOUNTING RE
4. door frame 15 Fasten the door bracket to the door jamb using two 2 12 x 5 8 color matched screws Figure 28 Figure 28 10 ADJ UST THE CLOSER Tools needed a In this step you will adjust the door closer Locate the adjustment screw at the end of the closer LEFT HINGE INTERIOR Views that attaches to the door frame Figure 29 RIGHT HNGE INTERIOR VEs 1 Open the door and then let it close to note the speed at which the door closes SLOWER ee 2 Using a Phillips head screwdriver to adjust the Z ray om aie closer to the desired speed O DE p R e For a faster closing speed turn the adjustment screw to the left counterclockwise e For a slower closing speed turn the adjustment nar P screw to the right clockwise wn P 3 Test the speed at which the door closes after each adjustment Adjust the screw more if needed to Figure 29 achieve the desired door closing speed Figure 29 REGULAR MAINTENANCE WINDOW GLASS The glass may be cleaned with any household glass cleaner Keep glass cleaners away from painted parts and brass nickel components PLASTIC PARTS Plastic door components may be cleaned by using a mild soap and water mixture and by gently rubbing the affected area Do not use harsh abrasives or any product that contains chlorine ALUMINUM PARTS Aluminum parts on the door may be cleaned by using a mild soap and water mixture and by gently rubbing the affected area Mineral sp
5. COMPONENTS Tools needed A j 3 eS i LEFT HINGE EXTERIOR Vievs In this step you will finish fastening the rain cap to the top mounting surface 8 8x1 1 Close the storm door 2 Adjust the rain cap so that the gap between the rain cap and door frame is the same along the entire length of the rain cap 3 Using the 1 8 drill bit drill holes in the mounting surface through the pre drilled holes in the rain cap Figure 18 4 Fasten the rain cap to the mounting surface using two 2 8 X 1 screws Figure 18 In this step you will cut the bottom of the latch rail to its proper length 5 Measure the height of the door opening measuring from the underside of the rain cap to the door sill You will use this measurement to cut the latch rail to its proper length 6 Locate the top of the latch rail Figure 19 7 Measure the latch rail starting Figure 19 at the top and then marking the BOTTOM bottom with the measurement that you took of the door Figure 20 epening 8 Using the hacksaw cut the latch rail to its proper length Figure 20 a Ce ee ees ee ee In this step you will attach the latch rail to the mounting surface _ T aii 9 Position the latch rail so that the top end of the latch rail is butted up against the underside of the rain cap Figure 21 10 Close the storm door 11 Measure the space between the latch rail and the sto
6. Fasten the door to the mounting surface using one 1 8 x 1 screw Using the level make sure that the door is plumb straight up and down While holding door in position use the 1 8 drill bit to drill holes in the mounting surface through the pre drilled holes in the hinge rail Fasten the hinge rail to the mounting surface using five 5 8 x 1 screws Figure 14 Open the storm door Using the 1 8 drill bit drill holes in the door jamb through the pre drilled holes in the hinge rail Fasten the hinge rail to the door jamb using eight 8 8 x 1 screws Figure 15 Do not overtighten the Screws In this step you will install the glass panel and retainers into the door frame 12 Starting at the mitered corners remove the clear protective tape from both the interior and exterior of the door frame if applicable 13 Center glass panel in bottom of door frame and carefully tilt it forward into opening in frame 14 While holding glass panel in place start inserting the side retainers Figure 16 e Position the side retainer at the top of the door frame cavity and then press flange of the side retainer firmly into the door channel Figure 17 until you hear a snap Continue this process until the entire retainer is Snapped into door frame e Install the other side retainer and both top and bottom retainers using these same techniques 5 Figure 17 5 INSTALL REMAINING FRAME
7. In this step you will cut the bottom of the hinge rail to its proper length 11 12 13 Measure the height of the door opening on the hinge side measuring from the underside of the rain cap to the door sill You will use this measurement to cut the hinge rail to its proper length Measure the hinge rail starting at the top and then marking the bottom with the measurement that you took of the door opening Figure 12 Using the hacksaw cut the hinge rail to its proper length Figure 9 TOP INTERIOR Figure 12 4 HANG HINGED STORMDOOR Tools needed LEFT HINGE Exterior Views i le a i a ra f Figure 14 I l Figure 17 4 5 14 8x1 In this step you will hang the storm door in the opening 1 Position the door in the opening so that the edge of the hinge rail is flush with the end of the rain cap and the top end of the hinge rail is butted up against the underside of the rain cap Figure 13 While holding door in position mark onto the mounting surface the location of the top most pre drilled hole in the hinge rail Once marked remove door from opening and set aside Using the 1 8 drill bit drill a hole in the mounting surface where you placed the mark Reposition the door in the opening and align the pre drilled hole in the hinge rail with the hole that you drilled in the mounting surface
8. Installation Guide for Andersen 1 1 4 Fullview Storm Doors Please Do Not Return Product to Store PLEASE call the storm door Solution Center at 1 800 933 3626 with any questions regarding installation mis cut part replacement lost part replacement or anything else related to your storm door purchase e If your abilities do not match the requirements of this installation contact an experienced contractor Andersen has no responsibility in regard to the post manufactured assembly and installation of Andersen products PARTS OVERVIEW Your storm door should contain the following parts Rain Cap Door Frame Hinge Rail with 4 hinges Hinge Side Z bar Glass panel Side Retainers 2 Top amp bottom Retainers 2 Latch Rail Handle Side Z bar Sweep Sweep Fin Side Screw Covers 2 Top Screw Cover 1 Not Shown Shipping Clip Door Mounting Screw Bag Handle Set Kit Closer Kit Insect Screen 00000 Figure 1 WINDOWS Da UR A EMCO Enterprises Inc is a wholly owned subsidiary of Andersen Corporation EMCO EMCO Enterprises Inc Andersen AY manufactures and supports the limited warranties for Andersen and EMCO doors PO Box 853 e Andersen EMCO and all other marks where denoted are trademarks of Andersen Des Moines IA 50306 0853 Come hame to Anderse Corporation 2011 Andersen Corporation All rights reserved i ie 11055 1 SAFETY FIRST PLEASE READ AND FOLLOW ALL
9. QUIREMENTS To install the storm door you must verify that there is the necessary opening width and height and a sufficient mounting surface 1 Measure the width at the top middle and bottom of the opening Figure 2 Measure from the inside of the brick mold or exterior trim 2 Measure the height at the center of the opening Measure from the inside of the brick mold or exterior trim down to the top of the bottom sill Use the this table Nominal Storm Opening Sizes to determine if your storm door will fit into Door Sizes W1 3 width H height the opening j i 30 x 80 35 3 4 TO 36 3 8 34 x 80 33 3 4 TO 34 3 8 33 x 80 32 3 4 TO 33 3 8 80 TO 80 7 8 32 x 80 31 3 4 TO 32 3 8 30 x 80 29 3 4 TO 30 3 8 Figure 3 3 Make sure that the brick mold or exterior trim meets the mounting surface requirements to install the rain cap hinge rail and latch rail Figure 3 You must have a minimum of e 1 mounting surface depth 3 4 mounting surface front e 2 1 2 space between the existing door and the mounting surface for the handle set installation 4 Most homeowners prefer to have the storm door handle on the same side as the entry door handle In shallow door openings this can cause the two handles to interfere Check for potential interference using the rough measurements Figure 4 If you anticipate that there will be interference hing
10. UT OF CONTRACT TORT OR OTHERWISE AND ITS LIABILITY WILL IN ALL INSTANCES BE LIMITED TO THE REPAIR OR REPLACEMENT OF THE DEFECTIVE PRODUCT Some states do not allow the exclusion of incidental and consequential damages or limitation of the duration of an implied warranty so the above limitations or exclusions may not apply to you This limited warranty gives you specific legal rights and you may also have other rights that may vary from state to state and in Canada What is NOT covered by this limited warranty damage caused by 1 improper installation maintenance or use 2 chemicals or airborne pollutants such as salt or acid rain 3 acts of God including wind damage 4 products not manufactured by EMCO EMCO Enterprises Inc is a wholly owned subsidiary of Andersen Corporation EMCO manufactures Andersen and EMCO storm doors EMCO supports the limited warranties cov ering Andersen Storm and Screen Doors Andersen EMCO and all other marks where denoted are trademarks of Andersen Corporation 2011 Andersen Corporation All rights reserved Reprinted and effective as of May 2011 10
11. ail on the right side of the storm door Refer to the illustrations in the column on the right side of the installation guide under this heading F j Figure 7 SE Figure 8 3 PREPARE STORMDOOR FOR HANGING Tools needed 4 A MESS LEFT HINGE Exterior View Ficure 9 TOP INTERIOR Figure 11 BOTTOM INTERIOR Figure 12 t In this step you will hang the rain cap against the top mounting surface Figure 9 Center the rain cap in the door opening Using a pencil mark the hinge side hole on the mounting surface Set rain cap aside Using the drill and 1 8 drill bit drill a hole in the mounting surface Place the rain cap back on the door opening Screw the 8 x 1 screw in the hole as indicated by the red arrow fastening the rain cap to the mounting surface Do not install the remaining screws at this time In this step you will attach the hinge rail to the door frame 7 10 Place latch side edge of door frame with holes on the ground TIP Lay on door carton Locate the top of the hinge rail Figure 10 Position the hinge rail along the hinge side edge of the door frame extending the top of the hinge rail 3 16 beyond the top of the door frame Snug the top hinge against the exterior side of the door frame Figure 11 Attach the top and remaining hinges to the door frame using 8 x 1 2 self drilling screws
12. e storm door on opposite side of your entry door For opening widths up to 1 wider or for mounting surface depth between 5 8 3 4 please call our Solution Center at 1 800 933 3626 to purchase a special kit to accommodate your situation 2 INSTALLATION PREPARATION In this step you will remove the insect screen and shipping clip INTERIOR SIDE UP 1 Lay the door flat on a protected surface with the exterior side down TIP Lay on door carton 2 Remove the insect screen by lifting it up and then away from the shipping clip Figure 5 3 Remove and properly discard the shipping clip Figure 5 In this step you will remove the side retainers and glass panel INTERIOR SIDE UP 4 Using your fingers grasp the exposed retainer lip Figure 6 Wf TIP To prevent kinks and damage to the side retainers do not pull 5 f straight up on them 6 a E 5 Pull the side retainer towards the center of the door frame working along the entire length of the side retainer 6 Remove the glass panel and set aside Stand the glass panel on its edge to prevent damage to it Figure 6 7 Left Hinged Figure 7 From the exterior a left hinged storm door will have the hinge rail on the left side of the storm door Refer to the illustrations in the column on the left side of the installation guide under this heading 8 Right Hinged Figure 8 From the exterior a right hinged storm door will have the hinge r
13. irits may be used and will not harm the paint This will remove many items such as glue residue Do not use harsh abrasives or any product that contains chlorine HANDLE COMPONENTS Brass handles and components except caming on windows may be cleaned in the following manner Brass handles and components are coated with a clear urethane finish which protects the brass from tarnishing In order to clean the brass this coating will have to be removed Upon doing this a larger area of brass will be exposed and sub ject to weathering Use a high quality brass polish according to the specific directions on that product A clear urethane may be reapplied to the clean surface to protect the finish Painted handles and components may be cleaned by using a mild soap and water mixture and by gently rubbing the affected area Do not use harsh abrasives or any product that contains chlorine ANODIZED FINISHED SWEEPS The anodized finished sweep may be cleaned with a mild solution of soap and water Do not use harsh abrasives or any product that contains chlo rine BRASS NICKEL GLASS CLEANING Brass and Nickel components may be cleaned with good quality cleaner such as Brasso LIMTED WARRANTIES PRODUCT LIMITED WARRANTY DOOR FRAME EMCO Enterprises Inc EMCO warrants the door frame hinges and painted finish on Andersen aluminum storm door products to be free from defects in manufactur ing materials paint adhesion or workmanship under normal u
14. rm door This space should be 3 16 along the entire length 12 Using the 1 8 drill bit drill holes in the mounting surface through the pre drilled holes in the latch rail Use the pre drilled holes in the latch rail as guides R Figure 21 13 Fasten the latch rail to the door Figure 21 opening using six 6 8 X 1 screws 6 INSTALL HANDLE SET In this step you will install the handle set 1 Refer to the instructions included in the handle set box to install the door handles You can match your Andersen storm door lock to Schlage or Kwikset entry door locks See handle set instructions contained within handle set box for details Kwikset is a registered trademark of Newfry LLC Schlage is a registered trademark of Schlage Lock Company 7 INSTALL SCREWCOVERS Tools needed NGE EXTERIOR Views In this step you will install the screw LEFTH Vi covers over the mounting screws in the rails and rain cap 1 Starting with the rain cap screw cover insert a groove in the screw cover into the bottom track of the rain cap Figure 22 2 Snap the groove in the top of the screw cover into the top track of the rain cap Figure 23 3 Repeat Steps 1 and 2 to install the remaining side screw covers Trim off any excess material Figure 22 Figure 23 Figure 22 Figure 23 amp INSTALL WEATHER SEALING COMPONENTS Tools needed ra 2 8x1
15. se for as long as the original consumer purchaser owns the home in which the door was initially installed COMPONENTS EMCO warrants the non glass and non insect screen fabric components of Andersen storm doors including brass and nickel hardware finish and the mechanical functions of balancers locksets closers windows and insect screens to be free from defects in manufacturing materials and workmanship for a period of five 5 years from the date of Original retail purchase or for as long as the original consumer purchaser owns the home in which the door was initially installed whichever is shorter Insulated glass is also warranted for a period of five 5 years not to develop under normal conditions any material obstruction of vision resulting from manufacturing defects or as a result of premature failure of the glass or hermetic seal In the event a door frame hinges insulated glass or a component fails as a result of a defect in manufacturing materials or workmanship within the limited warranty period specified above and upon written proof of purchase EMCO at its option will provide a replacement door frame hinge insulated glass unit and or components without charge installation is not included Such replacement or repair is warranted for the remainder of the original limited warranty period Please locate the door serial number and written proof of purchase and contact EMCO Consumer Support at 1 800 933 3626 Warranty claims made one
16. ure 5 8 below the window opening at the bottom on the hinge side and mark a line on the sweep or door frame 2 Extend the line onto the door jamb 3 Center the jamb bracket on this line placing it 1 4 behind the hinge rail 4 Using a pencil mark each jamb bracket hole on the door jamb 5 Using the drill and 5 32 drill bit drill a hole in the door jamb where you placed the marks 6 Reposition the jamb bracket and align its holes with the holes that you drilled in the door jamb 7 Fasten the jamb bracket to the door jamb using four 4 10 x 2 color matched screws Figure 26 z In this step you will install and pre set the push button closer Figure 27 ors 8 Attach the push button closer to the jamb bracket using the short pin 9 Attach the door bracket to the push button closer with the long pin 10 Press the push button on the push button closer and then pull extend closer by 1 4 3 8 1 4 3 8 Figure 27 Figure 27 In this step you will install the door bracket Figure 28 11 Close the storm door and then center the door bracket on the line from Step 1 12 Using a pencil mark each door bracket hole on the door frame 13 Using the drill and 5 32 drill bit drill a hole in the door frame where you placed the marks 14 Reposition the door bracket and align its holes with the holes that you drilled in the

Download Pdf Manuals

image

Related Search

Related Contents

Samsung Giorgio Armani    201410 - 小戸サンライズセーリングクラブ  Lorex 100 ft. High Performance Cable  advertencia - Alliance Laundry Systems  Lenovo ThinkPad X250  1.4 System Architecture  KERAGRIP - Kerakoll    ATTIX 9 STANDARD - Operating Instructions  

Copyright © All rights reserved.
Failed to retrieve file