Rust-Oleum Specialty 1936830 Use and Care Manual
Contents
1. TECHNICAL DATA SPC 13 SPECIALTY METALLIC SPRAYS e TRUSTED QUALITY SINCE 1921 RUSTOLEUM SPECIALTY DESCRIPTION AND USES Metallic sprays provide a rich brilliant finish on wood metal and more These sprays add a shiny metallic look to picture frames candle holders holiday crafts and much more This leafing metallic is designed for use on interior decorative items only PRODUCTS SKU Description 1910830 Gold 1915830 Silver 1936830 Brass 1937830 Copper PAINTING CONDITIONS Use outdoors or in a well ventilated area Use when temperature is between 50 90 F 10 32 C and humidity is below 85 to ensure proper drying Do not apply to surfaces when heated exceed 200 F 93 C Do not apply to galvanized steel Avoid spraying in very windy and dusty conditions Cover surrounding area to protect from spray mist PRODUCT APPLICATION SURFACE PREPARATION Remove all dirt grease oil salt and chemical contaminants by washing the surface with a commercial detergent or other suitable cleaning method Rinse with fresh water and allow to thoroughly dry Remove loose paint and rust with a wire brush or sandpaper Previously coated surfaces must be sound and in good condition Smooth hard or glossy finishes should be scarified by sanding to create a surface profile Removal of old paint by sanding scraping or other means may generate dust or fumes that contain lead LEAD IS TOXIC Contact the U S EPA Lead Infor2. 333 Rev 042914 TRUSTED QUALITY SINCE 1921 TECH N ICAL DATA TOLE i RUSTOLEUM PW ONRE TT ee PHYSICAL PROPERTIES Physical Properties METALLIC SPRAYS Resin Type Solvent Acrylic Pigment Type Varies with color Solvents Acetone Toluene Xylene MIR 1 90 Max Fill Weight 11 ounces Practical Coverage at Recommended DFT assumes 15 material loss Approximately 10 12 sq ft can 0 9 1 09 m can Touch Dry Times at 70 80 F OVC 15 minutes 21 272C and 50 Handle 30 minutes Relative Humidity Hocout Within 1 hour or after 24 hours Dry Heat Resistance 200 F 93 C Shelf Life 5 years Flash Point 156F 104 C Safety Information For additional information see MSDS The technical data and suggestions for use contained herein are correct to the best of our knowledge and offered in good faith The statements of this literature do not constitute a warranty express or implied as to the performance of these products As conditions and use of our materials are beyond our control we can guarantee these products only to conform to our standards of quality and our liability if any will be limited to replacement of defective materials All technical information is subject to change without notice ae RUST OLEUM BRANDS Rust Oleum Corporation Form GDH 333 11 Hawthorn Parkway Phone 877 385 8155 Rev 042914 Vernon Hills Ill
3. inois 60061 www rustoleum com An RPM Company
4. mation Hotline at 1 800 424 LEAD or log on to www epa gov lead PRODUCT APPLICATION cont APPLICATION Shake can vigorously for one minute after the mixing ball begins to rattle If mixing ball fails to rattle DO NOT STRIKE CAN Contact Rust Oleum Hold can upright 10 16 from surface and spray in a steady back and forth motion slightly overlapping each stroke Keep the can in motion while spraying Keep the can the same distance from the surface Apply two or more light coats a few minutes apart to avoid drips and runs Metallic sprays are not recommended for outdoor use Do not use near open flame DRY amp RECOAT Dry and recoat times are based on 70 F 21 C and 50 relative humidity Allow more time at cooler temperatures Dries to the touch in 15 minutes to handle in 30 minutes and is fully dry in 24 hours Apply a second coat within 1 hour or after 24 hours A clear coat finish is not recommended CLEAN UP Clean valve immediately after use by turning can upside down and depressing the spray button for 3 5 seconds some paint will be sprayed out so be careful to not inadvertently spray yourself or other objects Clean up wet paint with xylene or mineral spirits Properly discard empty container Do not burn or place in home trash compactor CLOGGING If the valve clogs twist and pull off spray tip and rinse ina solvent such as mineral spirits Do not insert any object into can valve opening Form GDH
Download Pdf Manuals
Related Search