Rust-Oleum Specialty 1918830 Use and Care Manual
Contents
1. LEAD pr log on to www epa gov lead PRODUCT APPLICATION cont APPLICATION Apply only when air and surface temperatures are between 50 90 F 10 32 C and the relative humidity is below 85 to ensure proper drying Use outdoors or in areas with good ventilation Avoid spraying in very windy or dusty conditions Cover surrounding area to protect from overspray Overspray can carry a significant distance Shake can vigorously for one minute after the mixing ball begins to rattle Shake often during use Hold can upright 12 16 from surface and spray in a steady back and forth motion slightly overlapping each stroke Keep the can the same distance from the surface Keep the can in motion while spraying Apply a base coat of one color first Then use leaves and twigs as stencils and lay them on the surface to make a random pattern Then use three or more colors to paint stripes and patterns over the leaves and twigs Do not use near open flame CLEAN UP Clean valve immediately after use by turning can upside down and depressing spray button for 3 5 seconds Clean up wet paint with xylene or mineral spirits Throw away empty can in trash pick up Do not burn or place in home trash compactor CLOGGING If the value clogs twist and pull off spray tip and rinse ina solvent such as mineral spirits Do not insert any object into can valve opening Form CS2434 Rev 042913 TRUSTED QUALITY SINCE 1921 TECH N ICAL DATA RUST2. OLEUM SPECIALTY SPECIALTY CAMOUFLAGE SPRAYS SPECIALTY CAMOUFLAGE SPRAYS Resin Type Acrylic Modified Alkyd Solvents Acetone Toluene Xylene Fill Weight 12 oz MIR 1 20 Max Practical Coverage at Recommended DFT Approximately 6 7 sq ft can 0 54 0 63 m can assumes 15 material loss Dry Times at Touch 20 minutes oes Sates Handle 1 hour Humidity Recoat Within 1 hour or after 24 hours Dry Heat Resistance 200F 93 C Shelf Life 5 years Flash Point 156 F 104 C Safety Information For additional information see MSDS The technical data and suggestions for use contained herein are correct to the best of our knowledge and offered in good faith The statements of this literature do not constitute a warranty express or implied as to the performance of these products As conditions and use of our materials are beyond our control we can guarantee these products only to conform to our standards of quality and our liability if any will be limited to replacement of defective materials All technical information is subject to change without notice ae RUST OLEUM BRANDS Rust Oleum Corporation Form CS2434 11 Hawthorn Parkway Phone 877 385 8155 Rev 042913 Vernon Hills Illinois 60061 www rustoleum com An RPM Company
3. pd TECHNICAL DATA SPC 02 SPECIALTY CAMOUFLAGE SPRAYS TRUSTED QUALITY SINCE 1921 RUSTOLEUM SPECIALTY A flat non reflective spray paint designed for use on wood metal and other surfaces to disguise or break up the outlines of items to blend in with different terrains These durable paints are suitable for outdoor use and resist chipping cracking and peeling Do not use on galvanized surfaces APPEARANCE Flat PRODUCTS FINISHES 1916830 Black 1917830 Khaki 1918830 Earth Brown 1919830 Deep Forest Green 1920830 Army Green 263653 Sand PAINTING CONDITIONS SURFACE PREPARATION ALL SURFACES Remove all dirt grease oil salt and chemical contaminants by washing the surface with a commercial detergent or other suitable cleaning method Mold and mildew must be cleaned with a chlorinated cleaner or bleach solution Rinse with fresh water and allow to thoroughly dry STEEL Scrape and wire brush or power tool clean to remove loose rust scale and deteriorated coatings Use 7569838 Red Primer for sound rusted or clean metal before application of a finish coat PREVIOUSLY COATED Previously coated surfaces must be sound and in good condition Smooth hard or glossy surfaces should be scarified by sanding to create a surface profile Removal of old paint by sanding scraping or other means may generate dust or fumes that contain lead LEAD IS TOXIC Contact the U S EPA Lead Information Hotline at 1 800 424
Download Pdf Manuals
Related Search