BEHR Premium DeckOver 500001 Instructions / Assembly
Contents
1. How to Prepare and Coat a Wood Surface with DECKOVER Coating Preparing an Uncoated Wood Surface Uncoated wood may still have mill glaze or loose wood fibers which can cause a coating to fail The PREMIUM PREP Products will prepare the uncoated surface allow the DECKOVER coating to fully adhere to the wood surface and ensure a longer lasting more durable finish Proper cleaning will help remove dead and loose wood fibers from the wood surface which is especially important for aged wood For Best Results Before applying DECKOVER coating to a wood surface be sure to use BEHR PREMIUM PREP PRODUCTS Whether your existing wood surface is uncoated or coated the BEHR PREMIUM PREP PRODUCTS will allow the newly applied coating to fully adhere to the wood surface and will ensure a longer lasting more durable finish Step 1 Wet surface with water prior to cleaning Using a pump sprayer apply BEHR PREMIUM All In One Wood Cleaner NO 63 to the wood deck surface Keep the surface completely wet with solution for 10 15 minutes Step 2 Scrub surface using a stiff bristle broom or brush Reapply the cleaning solution as needed to keep the surface wet Step 3 Thoroughly rinse the surface area with clean water using either a garden hose with a high pressure nozzle or a pressure washer Step 4 Continue the process until the entire project area is complete Allow the area to dry completely How to Prepare and Coat a Wood Surface with2. a paint tray and work a roller into the tray until it is fully loaded with coating For best results use a 1 2 roller cover TIP For larger areas consider using a 5 gallon bucket and a bucket grid Step 2 For nail holes and cracks up to 1 4 completely fill in with DECKOVER coating using a nylon polyester brush prior to coating Deep holes and cracks may require additional filling Step 3 Using a 2 2 wide brush cut in a 2 3 wide area around the deck floor where the roller cannot reach Start at a corner and follow the grain of the wood TIP To prevent lap marks only cut in a small area of 2 to 3 board widths at a time Apply DECKOVER Coating Step 5 Apply a generous even coat in the same section as the cut in and roll the coating approximately 4 down the boards TIP To avoid lap marks do not roll onto a new section until the previous section has been completed Step 6 Reload the roller with coating and continue to the next 4 section As you go roll back into the section immediately after the coat is applied Continue rolling until the first coat is completely applied Step 7 Once the first coat is completely dry fill in any remaining cracks if necessary and roll out the second coat How to Prepare and Coat a Wood Surface with DECKOVER Coating Bucket Broom Stiff Bristle Brush 2 2 Bucket Grid Chemical Resistant Gloves Drop Cloths Extension Pole Vinyl
3. DECKOVER Coating Step 1 Using a roller or nylon polyester brush apply BEHR PREMIUM Stain amp Finish Stripper NO 64 to a small section of the coated wood deck surface Reapply the stripper as needed to keep the surface wet for at least 15 minutes Do not allow the product to dry TIP Most deteriorated finishes will start to lift after 15 30 minutes Preparing a Coated Deck Surface Faulty existing coating can prevent full adhesion of your new DECKOVER coating The BEHR PREMIUM PREP PRODUCTS will help strip the old finish allow the new coating to fully adhere to the wood surface and ensure a longer lasting more durable finish Step 2 Using a stiff bristle broom or brush scrub the section after the finish begins to lift Step 3 Thoroughly rinse the surface area with clean water using either a garden hose with a high pressure nozzle or a pressure washer Step 4 Repeat the process of applying product and scrubbing in small sections until all peeling coating has been completely removed Step 5 Apply BEHR PREMIUM All In One Wood Cleaner NO 63 to clean and neutralize the surface prior to coating Allow the area to dry completely Stripping Peeling Coating See Label for Proper Protective Equipment How to Prepare and Coat a Wood Surface with DECKOVER Coating Step 1 Replace any rotting or unstable boards You may use a wood filler to fill cracks and holes larger than 1 4 Step 4 Pour DECKOVER coating into
4. Gloves Hose High Pressure Nozzle Paint Can Opener Paint Tray Paint Tray Liner Painters Tape Plastic Sheeting Pressure Washer Protective Apparel Pump Sprayer Rags Roller Cover Roller Frame Stir Stick BEHR PREMIUM Stain amp Finish Stripper NO 64 BEHR PREMIUM All In One Wood Cleaner NO 63 BEHR PREMIUM DECKOVER Coating Recommended BEHR Products Suggested Equipment
Download Pdf Manuals
Related Search