BEHR Premium 87501 Installation Guide
Contents
1. ONLY WITH ADEQUATE VENTILATION To avoid breathing s of use other means to ensure fresh ai tering heads inued difficulty is mediately wi CAUTION KEEP OUT OF REACH OF CHILDREN DO NOT TAKE INTERNALLY2. eRe BE Basement amp Masonry Waterproofer 2 Smooth Decorative Interior Exterior Flat Finish E MASONRY 10 Year Customer Satisfaction Guarantee WATERPROOF Mildew Resistant Film Withstands 12 PSI of Water Pressure Withstands 98 mph Wind Driven Rain Sprayable Saves Application Time Spread Rate Rough 7 Smooth READY TO USE OR ADD TINTING COLORANTS WHERE TO USE Walls subject to hydrostatic pressure Ideal for above or be Basement Walls Retaining Walls Garage Walls Masonry Walls Cinder Blocks Stucco Brick Foundations and Landscape Walls Apply to dry or slighty damp surfaces Not for use on floors or walls with active water leaks PREPARATION Proper surface preparation is required New or Unpainted Surfaces New concrete must cure for a minimum of 30 days Test for loose flaking concrete by pressing a piece of masking or cellophane tape at various places then pul it off with an abrupt action If the tape does from the surface it can be painted I the existing concrete is removed the loose concrete should be removed down to a sound substrate For below grade application All holes or cracks must be properly patched with a fast setting hydraulic cement For above grade application Prime all uncoated patched chalky and adjacent wood and or metal surfaces with a product such as BEHR PREMIUM PLUS NO 436 Exterior Muti Surface Primer amp Sealer Remove mildew stains with a mildew stain removing p
3. er brush or an airless sprayer 2 200 3 200 PSI using a 023 025 spray ip Two coats minimum are required First Coat Using a brush or roller work the waterproofer onto the surface until all pores or voids are covered Second Coat Using a brush or roller cover the entire surface Properly fill any voids left after the first coat Additional spot application may be needed depending on the porosity of the surface Important If leaking is still present after two coats it indicates that voids or pinholes are still open Re apply product to these areas DO NOT thin product or apply ata greater spread rate DRY TIME peratures or high humidity conditions will affect drying time should be reached in 7 14 days Full DISPOSAL Properly dispo ied rags and protect unused product from freezing For disposal of empty containers and unused product contact your household refuse collection service uu SS SUCH AS BRAIN DAMAGE ESPECIALLY IN CHILDREN PREGNANT SHOLLI D aoo EXPOSURE Wear a NIOSH approved respirator rs t yourself and your family by gad Information Hotline at 1 800 424 LEAD or log on tacting the National Li epa govilead WARNING Ti caine WARNING IRRITANT HARMFUL IF SWALLOWED CONTAINS ETHYLENE GLYCOL MAY CAUSE EYE NOSE AND THROAT IRRITATION AVOID CONTACT WITH SKIN AND EYES AND AVOID BREATHING OF VAPORS AND SPRAY MIST WEAR EYE PROTECTION AND PROTECTIVE CLOTHING USE
4. roduct Al surfaces must be clean and free of dirt dust efflorescence and oil Clean surface with a product such as BEHR PREMIUM NO 991 Concrete amp Masonry Cleaner amp Etcher Follow all label instructions Previously Painted Suri BEHR PREMIUM Basement amp Masonry Waterproof when applied to bare or untreated surfaces PREVIOUSLY PANTED SURFACES IN GOOD REPAINTABLE CONDITION MAY BE PAINTED WITH BEHR PREMIUM NO 875 or NO 876 HOWEVER BEHR WILL NOT GUARANTEE THE RESULTS Test for loose flaking paint by pressing a piece of masking at various places then pull it off with an abrupt the paint from the surface it can be painted If the existing paint i the loose paint should be removed down to a sound substrate by brushing or sanding For Interior or Exterior appl we deteriorated coating prior to application Follow all preparation instructions under New or Unpainted Surfaces above WARRANTY Visit www Behr com for complete warranty information 800 854 0133 Ext 2 U S A oniy 02011 Beh Process benne Santa Ana CA SZT USA VOC lt 100 g t A Masco Company p amp Water Clean Up APPLICATION Stir well before use Do not thin product Use with adequate ventilation Use oduct when air and surface temperature are 50 90 F 10 320 Apply to alls Wipe off any visible moisture with a dry painting Apply using a high quality 1 2 3 4 nap roller 4 nylon olyest
Download Pdf Manuals
Related Search