Veranda 73012501 Installation Guide
Contents
1. Baluster Post Sleeve Baluster Post Sleeve ly Add 2 screw covers for both top and bottom Note Repeat installation process for each brackets Add 2 screw caps for each top rail additional rail assembly bracket Top bracket shown only Attach 2 Screw Caps i For Each Top Rail Bracket Only y Attach 2 Screw Covers For Each Bracket H 5 Baluster D Mantin SS Transferable Limited Lifetime Warranty What is covered Barrette Outdoor Living warrants vinyl and aluminum products to include vinyl and aluminum fence vinyl and aluminum railing and plastic lattice against defects or workmanship for as long as you own your home Barrette Outdoor Living will at its option replace the product in question with new product of the same or equivalent value at no charge Barrette Outdoor Living warrants these products against peeling flaking splintering corrosion rusting or abnormal discoloration under normal use and service per ASTMD 2244 This warranty extends to the original purchaser or transferee as specified herein on the products noted above Separate and distinct warranties for hardware and other products are not covered under this warranty What this warranty does not cover This limited warranty does not cover damage resulting from accident unreasonable use neglect alteration improper service improper installation acts of God or any other causes not arising out of defects in materials or workmanship Additionally this war2. PURPOSE ON THE PART OF Barrette OR ITS LICENSORS SOME STATES DO NOT ALLOW THE EXCLUSIONS OF IMPLIED WARRANTIES OR LIMITATIONS OF HOW LONG AN IMPLIED WARRANTY LASTS SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU IF THE PRODUCT IS DEFECTIVE PER THE ABOVE COVERAGES YOUR SOLE AND EXCLUSIVE REMEDY SHALL BE REPAIR OR REPLACEMENT AS PROVIDED ABOVE BARRETTE AND ITS LICENSORS SHALL NOT BE LIABLE FOR ANY DAMAGES LOSS OF USE LOSS OF PROFITS OR INTERRUPTION OF BUSINESS WHETHER SUCH ALLEGED DAMAGES ARE BASED IN WARRANTY TORT CONTRACT OR INDEMNITY SOME STATES DO NOT ALLOW THE EXCLUSION OF LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU This warranty is valid only in the United States and Canada Refer to www BarretteOutdoorLiving com for specific details about warranty limitations 1 800 336 2383 To register your product please visit www barretteoutdoorliving com product registration Se Barrette Barrette Outdoor Living 7830 Freeway Circle e Middleburg Heights Ohio 44130 http www barretteoutdoorliving com 1 800 336 2383 Ds 34106878B0M V3 6 13
3. rail section between the posts each end of top and bottom rails Fasten Bottom Bracket to i Base with 1 10 X 1 Screw OAN As shown in Step 3 Top View Step 4b Mark 4 Screw Holes Each Bracket Mark 4 screw hole locations on each a bracket Set rail section aside then pre drill 1 8 diameter holes in post at each mark 7a J Step 4b Post Sleeve es 7 ey Barrel J Pam Pre drill 1 s diameter hole through top rail and aluminum insert for each side of top rail brackets only Fasten with 10 x 1 flat head screws Mie Attach each 2 top rail bracket with 4 10 x 2 screws Attach each bottom rail bracket with F 4 10 x1 2 screws 10 x 1 Flat Head Screws for Each Side of Top Rail Bracket O I O Q 3 a
4. 34106878B0M V3 6 13 gt ous Barrette amp Railing and Models Stair Railing Kit Assembly and Installation Instructions PLEASE READ OWNER S MANUAL COMPLETELY BEFORE ASSEMBLING YOUR RAIL OR STAIR KIT Traditional and Willlamburg Vinyl Railing Stair Railing amp Angle Bracket Kits Version To register your product please visit www barretteoutdoorliving com product registration Barrette Thank you for choosing the Barrette Outdoor Living Rail or z or Stair Rail Kit Please read the instructions completely before M ate ri a C h ec kl st assembling your rail Retain manual and your dated sales slip for future reference and warranty claims O Tape Measure O Drill Before You Begin O Level O Drill bits O Hacksaw or Chopsaw O 3 Wood Blocks Make sure your project meets local building codes before O Rubber Mallet O Pencil beginning installation 2 person installation recommended ATTENTION Before you assemble the kit PLEASE TAKE A COMPLETE INVENTORY OF ALL PARTS USING THE KIT CONTENTS DO NOT ATTEMPT TO ASSEMBLE THE KIT IF PARTS ARE MISSING OR DAMAGED Please do not return the product to the store for assistance or replacement parts call 1 800 336 2383 Top Rail e f E Balusters Spindles Top Rail Bottom Rail IT Support Brace o i SA Stair Brackets gt Balusters Spindles Bottom Rail Angle Brackets Ey For Vinyl Railing Instal
5. hown Fig A Assemble your rail section by snapping balusters spindles in rails Fig B Lock Tabs Outer edge holes Place assembled stair rail section adjacent to your posts as shown in Fig A Measure the distance from first and last baluster spindle to the top and bottom posts making sure distance is equal on both sides of stair rail section Clamp in place Fig B C Align top and bottom angle bracket on post adjacent to rail Mark rail at end of bracket repeat on all four brackets on rail section Check for proper bracket angle and mark window inside bracket Fig a Pre drill angle bracket through round holes two in top rail bracket one in bottom rail bracket with a s bit and add 10 x 1 screws to lock angle in place Fig b es S N Barrel J y Remove clamped stair kit from posts Locate previous marked rails and add 1 to your pre determined measurement Fig A Cut all four 1 marks on rails at 90 degrees Fig B Note There is a separate screw pack for the top rail brackets and the bottom rail brackets a Slide your angle brackets top bottom onto your rails and place stair rail section between your posts b Determine desired rail height and mark all bracket holes c Pre drill all bracket holes with a 1 8 bit d For Top Rail Brackets Only Position drill bit on center of post 2 from either side and between previously drilled four screw holes Pre drill using 32 dril
6. l bit all the way through steel insert e Attach 2 screw into post all the way through steel insert f Add screws to mount brackets to posts For top rails make sure to use 2 self tapping screws 4 per bracket For bottom rails make sure to use the 1 2 self tapping screws 4 per bracket g Pre drill each side of the top rail brackets using the screw holes provided Use provided 1 flat head screws and plastic caps to complete the installation Ry Barrette LL Angle Bracket Installation These installation guidelines will direct you through the process of installing the angle brackets This process is very similar to the installation of a regular railing installation with a few key differences These instructions depict installation methods that have been proven successful and are therefore recommended by the manufacturer Please keep in mind that they may not cover every installation scenario you may encounter Since each installation is unique in its performance requirements the ultimate installation method used is the sole responsibility of the installer After posts have been installed determine angle Pre drill s diameter holes in base then fasten bracket at and height of railing i the determined angle Determine Angle Fasten bracket to Base with 2 10 x 1 Screws for Top Bracket Only Top View Cut railing to desired length Place bracket on Position the
7. lation Closely follow post installation instructions or sleeve existing wood 4x4 Assembling rail section center of bottom rail For 67 14 rail install center of support brace 33 3 4 from ends of rail b 2 support braces are included with 8 railing kits Measure length of rail divide by 3 and measure that distance from your rail to the center of your first support brace and install support brace Repeat that step from the opposite side of your rail For 92 rail divide 92 by 3 3074 install both support braces 307 from their respective ends Cut two 3 temporary wood spacer blocks not included to insert under ends of railing sections to temporarily assist in aligning railing section 3 Support Brace 3 Wood Block For Bottom Brackets Using a 2 drill bit pre drill first bottom bracket screw hole On angle drill through bracket hole vinyl post jacket and vinyl insert Repeat Steps 5 amp 6 for the remaining three screws for the first bottom bracket Repeat Steps 5 7 for the second bottom bracket Look down from the top of post to make sure screws are penetrating steel post if using steel post install kit 7 N wa A ag s N J Tighten first screw Repeat Steps 8 10 for the second top bracket rs Barrette J e Lock tabs on baluster spindle must face outer edge of routed holes in rails e Assemble your rail section by snapping balusters
8. ranty does not cover costs of installation removal reinstallation or surface mold and mildew created by excessive environmental conditions Any service or repair provided outside the scope of this limited warranty shall be at Barrette Outdoor Living s rate and terms then in effect What do we do to correct the problems Should your Barrette Outdoor Living product prove defective under warranty reference the website or call the phone number listed below Your problem will be assigned a tracking number and an authorized Barrette Outdoor Living representative will contact you to arrange a convenient time to schedule an onsite inspection or request pictures if need be If after inspection product is deemed to be manufacturer defect we will make arrangements to rectify the issue You must have proof of your purchase in order for the problem to be corrected Transferee Coverage Warranty coverage will be extended to one transferee on the above listed products with the following limitations Transferee must obtain an original or copy of the initial sales receipt with proof of date from the previous owner s Additionally if fence is purchased from a builder or installer documentation must be supplied that names the product installed on property and date of transfer THIS WARRANTY IS IN LIEU OF ALL CONDITIONS OR WARRANTIES EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO ANY IMPLIED CONDITIONS OR WARRANTIES OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR
9. spindles in rails a 1 support brace is included with 6 railing kits Measure equal distance from both ends of railing and install support brace in 3 3 SUPPORT BRACE Slide two top and bottom rail brackets on ends of completely built rail sections Slide rail section in between posts and on top of temporary wood spacer blocks position wood spacer blocks next to installed vinyl posts Drive first of the shorter screws 1 through bottom bracket to post For Top Brackets Install the two side screws first Using a 2 drill bit pre drill first hole on angle through first top rail bracket vinyl post jacket and into wood or steel post make sure to have drill at full speed when starting into the steel post and loosely install the first 2 2 screw Repeat pre drilling process for second screw again remember to have drill at full speed when starting into the steel post and tightly install second screw Install final 1 4 screws through bottom of top rail 12 brackets into top rail WS Barrette rr For Vinyl Stair Railing Installation 65 3 4 max am between posts Closely follow post installation instructions or sleeve existing wood 4x4 Mount top post 1 back from edge of landing Mount bottom stair post 1 back from stair tread nose Distance between posts should not exceed 65 Lock tabs on baluster spindle must face outer edge of a routed holes in rails as s
Download Pdf Manuals
Related Search