Veranda 73009370 Installation Guide
Contents
1. E Barrette 2 Gate Installation Self closing hinges are included with all gates Make sure hinges are set the proper direction to accommodate either left or right handed gates or provide an inside or outside swinging gate The post that will have the gate hinges screwed to it will be the thick walled heavy duty gate post _ Make sure the flange side of the hinge is the side the gate and post will be gy installed onto Release tension of hinges with a standard screwdriver prior to installing Take a flathead screwdriver and push in the tension adjuster and turn 1 2 turn If the gate is not attached to fence sections on both sides then it is advised to install the hinge on the side of the gate with the fence section attached D Opening Direction Gate Post Once the concrete has completely set around the gate post s may take L Hang gate to post Make sure the horizontal rails of the gate are at 5 7 days gates may be hung the same level as the horizontal rails of the fence panels Do this me by either lifting gate by hand or by inserting temporary spacer W blocks under the gate to keep gate in2. uwawan Repeat by digging next hole and filling with 6 of gravel Then insert the next panel into the previously installed post Place the next post into the dug hole and slide the post onto the rails of the panel as far as possible Pour concrete around that post and tamp down leaving concrete about 2 from ground level Repeat until end of line Barrette Corner posts require some additional handling on one of the fence panels The rails of one panel need to be notched 1 2 to allow the rails to nest adequately within a corner installation Top view of corner post Once four so panels are installed check to make sure all posts and panels are still level If a correction needs to be made use a rubber mallet while the concrete is still somewhat soft After concrete has set fasten the fence section to the posts using 8 x 1 self tapping screws Be careful not to over tighten screws because screw heads may break off or strip out
3. ALUMFENCEA_BOM V2 11 12 5 Barrette Aluminum y Prebuilt Fence Owner s Manual Installation Instructions PLEASE READ OWNER S MANUAL COMPLETELY Version BEFORE ASSEMBLING YOUR FENCE ALL STATED SIZES ARE NOMINAL DIMENSIONS For Home Haven AFCA BOM VET Select amp Premier Series To register your product please visit www barretteoutdoorliving com product registration Please read these instructions carefully before installing your Barrette fence If you have any questions or issues installing the fence please contact us at 1 800 336 2383 for assistance Barrette Before You Begin Check your local zoning laws e Local zoning laws and Home Owners Associations may regulate the location style and height of your fence or even require a permit signoff beforehand Contact your local utilities companies e You must have the utility companies clearly mark your property for electrical gas or water lines to avoid puncturing any unseen underground utilities Pay to mark your property line e Being proactive will save you time and money from any disputes from neighbors 2012 Barrette Outdoor Living 7830 Freeway Circle Middleburg Heights Ohio 44130 Sketch Plan and confirm materials needs e First draw or sketch out your fence plan to paper This drawing will help you estimate materials and plan location of cor
4. sides to connect fence sections Corner Post Used to connect two sections of fence coming together at 90 End Post Used to end a line of fence Only one section of fence will connect to an end post End Post Corner Post Blank Post Has no holes and is used with a gate latch Heavy Duty Gate Post Features a heavier wall than all other posts to support the weight of the gate attached with hinges Similar to an end post the HD Gate Post only has holes on one side EO nsccnOmrr 2 Product Overview Post Top A 5 N Notch L i A Middle Rail Post Bottom Rail D Barrette 2 5 www Layout installation J Ia I 72 6 e Using the worksheet as a guide establish your fence line by p staking out the areas you wish to enclose Locate each point For 6 sections using 2 posts in which you will need an end corner or gate post and mark it witha stake Actual Panel size is 71 Center to Center post distance is 17 wider than panel e To mark all other posts For 6 sections and using 2 posts from the center of an end point measure 72 146 and mark with stake For 8 sections and using 21 2 posts from the center of an end point measure 96 and mark with stake 96 NOTE If you left with a space less than a full panel the panel can be cut down to fit the space by using a hacksaw For 8 sections
5. arrange a convenient time to schedule an onsite inspection or request pictures if need be If after inspection product is deemed to be manufacturer defect we will make arrangements to rectify the issue You must have proof of your purchase in order for the problem to be corrected Transferee Coverage Warranty coverage will be extended to one transferee on the above listed products with the following limitations Transferee must obtain an original or copy of the initial sales receipt with proof of date from the previous owner s Additionally if fence is purchased from a builder or installer documentation must be supplied that names the product installed on property and date of transfer THIS WARRANTY IS IN LIEU OF ALL CONDITIONS OR WARRANTIES EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO ANY IMPLIED CONDITIONS OR WARRANTIES OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THE PART OF Barrette OR ITS LICENSORS SOME STATES DO NOT ALLOW THE EXCLUSIONS OF IMPLIED WARRANTIES OR LIMITATIONS OF HOW LONG AN IMPLIED WARRANTY LASTS SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU IF THE PRODUCT IS DEFECTIVE PER THE ABOVE COVERAGES YOUR SOLE AND EXCLUSIVE REMEDY SHALL BE REPAIR OR REPLACEMENT AS PROVIDED ABOVE BARRETTE AND ITS LICENSORS SHALL NOT BE LIABLE FOR ANY DAMAGES LOSS OF USE LOSS OF PROFITS OR INTERRUPTION OF BUSINESS WHETHER SUCH ALLEGED DAMAGES ARE BASED IN WARRANTY TORT CONTRACT OR INDEMNITY SOME STATES DO NOT ALLOW THE EXCLUSION O
6. place while mounting it to Set the hinges on the gate Line up the top of hinge with top of top gate gate post rail Line up bottom of bottom hinge with bottom of bottom gate rail Drive two 1 self tapping screws through upper hinge into gate use the inside holes for this step Repeat for bottom hinge la Drive two 17 self tapping screws through upper hinge into post use the inside holes for this step Repeat for bottom hinge Screw additional eight g Screws into hinge Barrette Install latch per instructions Varies by style lam Re tighten the spring tension of hinge to level started at turn cam clockwise 2 turn Transferable Limited Lifetime Warranty What is covered Barrette Outdoor Living warrants vinyl and aluminum products to include vinyl and aluminum fence vinyl and aluminum railing and plas
7. using 21 2 posts Notch the cut ends of the horizontal rails so they will seat inside of post See Illustration Actual Panel size is 9417 Center to Center post distance is 1 wider than panel e Attach string to each stake NOTE the fence will most likely need to be set back from the property line as required by your local codes usually 27 47 Aluminum Fence Rail Notcher can be purchased separately First Post Installation Use a rubber mallet to gently drive the post tops onto the posts Be careful not to damage the post top Mix the concrete on the dry side to allow the posts to set faster See chart below to determine the minimum depth for your fence NOTE In areas where ground frost occurs the concrete footing Should be extended below the frost line generally 12 below This will account for frost heave in which ground water freezes and expands upwards By providing this 12 drainage you can keep the frost heave from affecting the posts Verify depths meet all local building codes Panel Post Hole Post Leave 2 goes into from ground Height Height Depth ground we wf r E gt vaOn wr PEarret e 2 Start post installation with gate corner end Dig post holes p appropriate depth approximately 6 wide Fill bottom of hole with J approximately 6 of peastone gravel and place post onto gravel Fill holes with concrete and tamp down around each post leaving concrete about
8. 2 from ground level L If using a gate the opening between the posts should be 1 wider than the m gate width to allow for hinges Example Use a 48 opening for a 467 wide gate Be sure posts are level and plumb Brace the posts as necessary while the concrete is setting Width of Gate or Panel if not using a gate OC Leave 2 from ground 6 Gravel 9250 Panel Post Installation CAUTION Do not install all posts first Installation should proceed post panel post panel Place the next required post line corner end into the dug hole and Slide the post onto the rails of the panel as far as possible Pour concrete around that post and tamp down leaving concrete about 2 from ground level You now have one fence panel upright between two installed posts NOTE It is a good idea to have the next post hole in the run already dug when attaching panel to the previous post and have the 6 of gravel inside As the gate post or corner is setting up install the first fence panel Insert the horizontal rails from the panel into the punched holes from the previously installed post Place the rails as far into the post as they will go
9. F LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU This warranty is valid only in the United States and Canada gt 1 Barrette Outdoor Living 7830 Freeway Circle Middleburg Heights Ohio 44130 http www barretteoutdoorliving com 1 800 336 2383 ALUMFENCE_BOM V2 11 12
10. ners and gates Show the house driveway deck and property lines Then measure accurately with tape measure and identify those on your sketch e Layout should show fence lines and gate locations Determine number of sections and posts needed The opening left for gates should be the width of the gate ordered A 48 walk gate opening should be left for a 48 gate which is made at an actual width of 46 5 to fit a 48 Opening Installation Tips e Gates need to be installed on level ground e Gates and fence panels should be installed so that the bottom of the fence is 2 above ground level to allow for lawn maintenance cutting e installed the top of the post will be at the same height as the top of the tallest part of the fence panel e Separate and identify your posts The rails from the fence panels will be inserted into the pre punched holes of the posts waww Fsss Material Ghecklist O String Stakes Tape Measure Post Hole Digger Shovel O Level O Hacksaw Rubber Mallet Concrete Mix Peastone ATTENTION Before you assemble the fence PLEASE TAKE A COMPLETE INVENTORY OF ALL PARTS USING THE KIT CONTENTS DO NOT ATTEMPT TO ASSEMBLE THE FENCE IF PARTS ARE MISSING OR DAMAGED Please do not return the product to the store for assistance or replacement parts call 1 800 336 2383 E CHILDREN S PLAY AREA B E E E Line Post Post with holes on two opposite
11. tic lattice against defects or workmanship for as long as you own your home Barrette Outdoor Living will at its option replace the product in question with new product of the same or equivalent value at no charge Barrette Outdoor Living warrants these products against peeling flaking splintering corrosion rusting or abnormal discoloration under normal use and service per ASTMD 2244 This warranty extends to the original purchaser or transferee as specified herein on the products noted above Separate and distinct warranties for hardware and other products are not covered under this warranty What this warranty does not cover This limited warranty does not cover damage resulting from accident unreasonable use neglect alteration improper service improper installation acts of God or any other causes not arising out of defects in materials or workmanship Additionally this warranty does not cover costs of installation removal reinstallation or surface mold and mildew created by excessive environmental conditions Any service or repair provided outside the scope of this limited warranty shall be at Barrette Outdoor Living s rate and terms then in effect What do we do to correct the problems Should your Barrette Outdoor Living product prove defective under warranty reference the website or call the phone number listed below Your problem will be assigned a tracking number and an authorized Barrette Outdoor Living representative will contact you to
Download Pdf Manuals
Related Search