PetSafe PPA00-10984 Instructions / Assembly
Contents
1. To replace the insulated flap remove flap screws and flap support from top of pet door frame Remove vinyl flap and flap clamp with attached insulated flap Remove screws insulated flap and backing plate from back of flap clamp Insert new insulated flap between flap clamp back and backing plate Align screw holes Replace and tighten screws Follow step 3 under Vinyl Flap Replacement and Adjustment on page 9 Replacement Parts and Accessories Replacement flaps can be purchased by visiting www petsafe net or by contacting our Customer Care Center at 1 800 732 2677 10 Customer Care Center 1 800 732 2677 TERMS OF USE AND LIMITATIONS OF LIABILITY 1 Terms of Use This product is offered to you conditioned upon your acceptance without modifications of the terms conditions and notices contained herein Use of this product implies acceptance of all such terms conditions and notices 2 Proper Use This product is designed for use with pets where training is desired The specific temperament of your pet may not work with this product If you are unsure whether this is appropriate for your pet please consult your veterinarian or certified trainer Proper use includes reviewing the entire Installation Guide provided with your product including any specific safety information 3 Limitations of Liability In no event shall Radio Systems Corporation2. protect teach love Extreme Weather Pet Door Installation Guide for Small Medium and Large Please read this entire guide before beginning Model Numbers PPAO0 10984 PPAOO 10985 PPAOO 10986 Important Safety Information Explanation of Attention Words and Symbols used in this guide 1 This is the safety alert symbol It is used to alert you to potential personal ACAUTION AWARNING injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death WARNING indicates a hazardous situation which if not avoided could result in death or serious injury CAUTION used with the safety alert symbol indicates a hazardous situation which if not avoided could result in minor or moderate injury NOTICE is used to address safe use practices not related to personal injury When children are present in the home it is important to consider the pet door during child proofing activities the pet door may be misused by a child resulting in the child accessing potential hazards that may be on the other side of the pet door Purchasers Homeowners with swimming pools should ensure that the pet door is monitored at all times and that the swimming pool has adequate barriers to entry If a new hazard is created inside or outside of your home which may be accessed through the pet door Radio Systems Corporation recommends that you properly guard access to the hazard or remove the pet
3. door The closing panel or lock if applicable is provided for aesthetic and energy efficiency purposes and is not intended as a security device Radio Systems Corporation will not be liable for unintended use and the purchaser of this product accepts full responsibility for oversight of the opening it creates Power Tools Risk of severe injury follow all safety instructions for power tools Be sure to always wear safety goggles The user prior to installation must become familiar with all building codes that may affect the installation of the pet door and determine along with a licensed contractor its suitability in a given installation This pet door is not a fire door It is important for the owner and contractor to consider any risks that may be present inside or outside of the pet door and any risks that may be created by subsequent changes to your property and how they may relate to the existence and use including misuse of the pet door Be sure to use heavy scissors for cutting the core covers If cutting a metal surface be aware of sharp edges to prevent injury Customer Care Center 1 800 732 2677 e Keep these instructions with important papers be sure to transfer these instructions to the new owner of the property e If painting the pet door it is recommended to paint it prior to installation For best results use a primer for plastics before applying paint e If homeowner s door or other application is not le
4. pet door dimensions e Cut Out Size Opening cut in homeowner s door for proper fit and pet door installation e Replacement Flap Size Overall flap size when removed from pet door During extreme changes in weather vinyl flaps can shrink during cold months and stretch in warmer months Flap Opening Size Usable flap size for pet to enter and exit through pet door e Interior Frame Pet door frame on the inside of home e Exterior Frame Pet door frame on the outside of home Insulated Flap Yellow flap located behind the vinyl flap in the interior frame e Plastic Core Covers Plastic pieces that cover the cut out or core of the homeowner s door Snap on Closing Panel Cover that snaps onto the pet door frame to close the pet door opening 4 Customer Care Center 1 800 732 2677 Installation Instructions NOTICE If painting the pet door it is recommended to paint it prior to installation For best results use a primer for plastics before applying paint Determine Pet Door Location 1A Measure and mark your pet s shoulder height on the interior side of door 1B Determine location for the pet door Draw a vertical center line through the shoulder height line using a level NOTICE If homeowner s door or other application is not level the pet door must be marked level to swing properly 2A Remove door by removing door hinge pins 2B Place on a raised level surface such as saw
5. the pet door To Adjust slightly loosen flap screws on top of pet An additional closing panel sold separately can be used door frame on the exterior frame of the Extreme Weather Pet Door for improved weather resistance See Replacement Parts and Accessories on page 10 Customer Care Center 1 800 732 2677 Vinyl Flap Replacement and Adjustment During extreme changes in weather vinyl flaps can shrink during cold months and expand in warmer months Easily replace or adjust to ensure a snug fit during seasonal changes Remove vinyl flap and flap clamp with attached insulated flap MAA Interior flap clamp has insulated flap attached exterior flap clamp does not www petsafe net Replace flap clamp with attached insulated flap Insert new vinyl flap between flap clamp and flap screw holes in top of frame The PetSafe logo Should be readable on vinyl flap Replace flap support Align screw holes in flap support frame vinyl flap and flap clamp Replace and start screws to hold flap in place Adjust flap horizontally until centered in pet door frame Adjust flap vertically until magnet bar on frame jumps to meet magnet on bottom of flap Tighten screws Adjust flap horizontally until centered in pet door frame Adjust flap vertically until magnet bar on frame jumps to meet magnet on bottom of flap Tighten screws Insulated Flap Replacement
6. be liable for any direct indirect punitive incidental special or consequential damages whatsoever arising out of or connected with the use or misuse of this product Buyer assumes all risks and liabilities from the use of this product 4 Modifications of Terms and Conditions Radio Systems Corporation reserves the right to change the terms conditions and notices under which this product is offered www petsafe net 11 Radio Systems Corporation 10427 PetSafe Way Knoxville TN 37932 1 800 732 2677 www petsafe net 400 1352 2007 Radio Systems Corporation
7. bs of frame Hold frame together Insert nylon screws through holes in interior frame into holes in exterior frame Thread a hex nut onto bottom of each screw AK 4A Measure the thickness T of your door Note this measurement 4B Cut the grooved side of the plastic core covers and core cover supports to equal the thickness T of your door Left Support Right Support 5B Start screws but do not tighten at this time Place foam strip under interior frame for additional insulation Cut off any excess Helpful Tip Use a screwdriver to tuck the foam strip under as you work around the frame 5C Use a screwdriver to evenly tighten screws through out frame while keeping core covers in position It may be necessary to adjust screws to make sure pet door fit is correct Helpful Tip Look though flap opening to check if core 4C Place cut edge of bottom core cover toward you covers are in position as you tighten the screws with ribbed side facing up Snap left core cover support into left end of T shaped rib on bottom core cover Snap right core cover support into right end of T shaped rib on bottom core cover With channel sides facing in align uncut edge side with one rib 5D Use wire cutters to trim screws flush with exterior frame NOTICE of side core covers with uncut edge of core cover Optional Use a manual screwdriver to tighten screws Do not supports Slide channel of side core covers ont
8. e will be able to help you faster Most importantly PetSafe will never give or sell your valuable information to anyone Complete warranty information is available online at www petsafe net Kit Includes Tools Needed Snap on Closing Panel gt Hamrick Interior Frame with 2 flaps e Jigsaw Plastic Core Covers j A mo Cutting Template e 2 Drill Bit Installation Guide e Wire Cutters Exterior Frame e Slotted amp Phillips with Flap Screwdrivers Hex Nuts e Tape Measure Small 4 pcs e Tape Medium 6 pcs Large 10 pcs e Pencil Nylon Screws e Level Small 4 pcs e Scissors See ee e Safety Equipment Core Cover Optional Supports e Duct Tape Foam Strip e Caulk Weather Strips NOTE The Extreme Weather Pet Door can be installed in most doors and walls Installation in thinner or thicker applications may not require the Plastic Core Covers If installing in a wall reduce cut out width by 1 for the Small and Medium For the Large reduce cut out width by 1 and cut out height by 1 Additional tools and materials such as wood framing may be required Want Professional Installation Help Invisible Fence Brand installers where available may come to your home and install your new PetSafe Pet Door for an additional cost Contact the Customer Care Center at 1 877 866 DOGS 3647 or visit the website at www invisiblefence com for more information Key Definitions e Outer Frame Size Overall
9. horses Place interior side of door facing up Helpful Tip Clamp down the door to prevent it from moving Dts The Pet Door can be installed with the door hanging based on your skill level 2C Cut out the correct size template Match the marked lines on the door with the shoulder and center lines on the template Tape the template in place and carefully trace template Make sure to trace under neath tape and connect the corners Now remove the template and any excess tape from the door NOTICE Cut out correct size template For the Large no cutting is required If installing in a wall reduce cut out width by 1 for the Small and Medium For the Large reduce cut out width by 1 and cut out height by 1 NOTICE When applying cutting template there should be a minimum of 3 between the bottom and sides of the door and the outer edge of the cutting template to maintain the structural integrity of the door www petsafe net 5 Cut Pet Door Opening 4E Snap uncut edge side with one rib of assembled core covers inside bottom and side tabs of interior frame frame with 2 flaps The bottom core cover should be at bottom of interior frame Weather strips and ribbed sides uncut edges should face flap Snap the uncut edge side with one rib of top core cover inside top tabs of interior frame Uncut edge side with one rib of top core cover should face flap Core covers may need trimming to meet at corner
10. o tab of i ere See P can strip the screws or core cover supports to form a U shape warp the pet door frame y 4D Slide weather strips into channels of side core covers Weather strips should face inside Weather strips may need trimming to meet at end of side core covers lo ateyat ies Caulk around the exterior frame frame with one flap and inside threshold where core covers meet for weather resistance Customer Care Center 1 800 732 2677 www petsafe net 7 Train Your Pet Replacement Flaps 6A Rehang your door and begin training your pet It may help for you to be on one side of the door and your pet on the other Lift or tape open flap and try to talk your pet through the pet door After your pet has gone through a few times allow the flap to touch your pet s back so they will become comfortable using the pet door If your pet will not go through the door tape the flap open until they use it on their own Helpful Tip Try treats or toys to encourage your pet to go through the pet door and become comfortable using it Closing Panel To Replace vinyl flap remove flap screws and flap support from top of pet door frame OAA Interior flap has a flap support exterior flap does not The Closing Panel snaps onto the interior frame of the Extreme Weather Pet Door It is useful during inclement weather or to keep your pet from using
11. s 3A Drill 2 holes in inside corners of drawn template These will be the pilot holes for the saw blade Helpful Tip Use both hands to hold drill steady and straight at a 90 angle 3B Beginning in one of the holes just drilled cut along the drawn template lines After cutting out the opening you may need to recut to square the opening This is necessary for the pet door frame to fit correctly Helpful Tip Use proper saw blade length and type according to door thickness and material for example a wood blade for a wood door and a metal blade for a metal door Cut slowly using both hands to hold the saw steady and straight at a 90 angle This will prevent the blade from cutting unevenly between interior and exterior sides of the door orien oF dteiteleg Use duct tape in the i corners of core covers to help secure in place and to improve weather resistance Cut off any excess tape Install Pet Door NOTICE Fi it HESS aie phate is pay a oe door where an Before putting away jigsaw place the exterior frame frame with 1 flap into aa lk cle A the underside of the opening to check the fit If the screw holes on frame are not visible through cut out you may need to recut opening before proceeding with the installation Fit Core Covers 5A Place interior frame frame with 2 flaps into cut out Next place exterior frame into cut out from under side of door inserting core covers inside ta
12. vel the pet door must be marked level to swing properly e Cut out correct size template For the Large no cutting is required If installing in a wall reduce cut out width by 1 for the Small and Medium For the Large reduce cut out width by 1 and cut out height by 1 e When applying cutting template there should be a minimum of 3 between the bottom and sides of the door and the outer edge of the template to maintain the structural integrity of the door e Make sure there is nothing underneath the door where you will be drilling the holes or cutting out opening e Use a manual screwdriver to tighten screws Do not overtighten Overtightening can strip the screws or warp the pet door frame www petsafe net Thank you for choosing the PetSafe brand You and your pet deserve a companionship that includes memorable moments and a shared understanding together Our products and training tools promote a lifestyle of protection teaching and love essentials that influence memories for a lifetime If you have any questions about our products or training your pet please visit our website at www petsafe net or contact our Customer Care Center at 1 800 732 2677 PRODUCT WARRANTY To get the most protection out of your warranty please register your product within 30 days at www petsafe net By registering and keeping your receipt you will enjoy the product s full warranty and should you ever need to call the Customer Care Center w
Download Pdf Manuals
Related Search