ZyXEL ZyAIR B-320 User's Manual
Contents
1. Windows does not auto detect the ZyAIR Make sure the ZyAIR is inserted into the computer PCI slot properly and then restart your computer Check the LEDs on the ZyAIR Perform a hardware scan by clicking Start Settings Control Panel and double clicking Add Remove Hardware Steps may vary depending on the version of Windows Follow the on screen instructions to search for the ZyAIR and install the driver Check for possible hardware conflicts In Windows click Start Settings Control Panel System Hardware and then click Device Manager Verify the status of the ZyAIR under Network Adapter Steps may vary depending on the version of Windows Install the ZyAIR in another computer If the error persists you may have a hardware problem In this case you should contact your local vendor2. object Remove the computer cover and a slot cover from a PCI slot Insert the ZyAIR into an available PCI slot Make sure the ZyAIR s contacts are fully seated in the slot Secure the ZyAIR to the chassis with a bracket screw Attach the included antenna to the ZyAIR The antenna should be perpendicular to the ground Replace the computer cover and power on your computer 12 Windows 2000 If a warning window displays click Yes 13 Windows XP A Found New Hardware Wizard windows displays Select Install the software automatically recommended and click Next 14 Windows XP If a warning window displays click Continue Anyway Then click Finish to complete the installation process After you install the ZyAIR Utility and insert the ZyAIR an icon appears in the system tray If the ZyAIR Utility icon displays the ZyAIR is installed properly Refer to the ZyAIR Utility User s Guide to configure the ZyAIR LED Display POWER LED The following table describes the LEDs on the ZyAIR LED COLOR STATUS DESCRIPTION POWER Green On The ZyAIR is receiving power Off The ZyAIR is not receiving power LED COLOR STATUS DESCRIPTION WIRELESS Green On The ZyAIR has a connection to a wireless LAN Blinking The ZyAIR is sending or receiving data Off The ZyAIR is not connected to a wireless LAN Troubleshooting PROBLEM CORRECTIVE ACTION
3. ZyAIR B 320 Wireless LAN PCI Adapter Quick Installation Guide Version 1 00 December 2003 ZyXEL Unleash Networking Power Important Note Federal Communications Commission FCC Interference Statement To comply with FCC RF exposure compliance requirements a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons This Transmitter must not be co located or operating in conjunction with any other antenna or transmitter Refer to the User s Guide for general FCC statements Procedure to View a Product s Certification s 1 Go to www zyxel com 2 Select your product from the drop down list box on the ZyXEL home page to go to that product s page 3 Select the certification you wish to view from this page 1 Installation Requirements Before installation make sure you have the following requirements e Pentium II 300MHz or above e A minimum of 6 MB available hard disk space e A minimum of 32 MB RAM e A CD ROM drive e APC slot e Windows 98 SE Me 2000 XP e Windows 98 SE users may need the Windows 98 SE CD 2 ZyAIR Utility and Hardware Installation The installation procedures are similar for all supported Windows versions Windows XP screen shots are shown unless otherwise specified DO NOT insert the ZyAIR at this point 1 Insert the support CD into the CD ROM drive on your computer The CD auto runs Otherwise locate and double click on setup exe A We
4. lcome screen displays Click Next 2 Click Next to accept InstallShield Wizard the default file location Choose Destination Location Select folder where Setup will install files or click Browse to select an alternate Setup will install ZyAIR WLAN Utility in the following folder To install to this folder click Next To install to a different folder click Browse and select folder another folder Destination Folder C Program Files ZyAlR WLAN Utility 11 Ifa warning window Software Installation displays click Yes A The software you are installing has not passed Windows Logo W indows 2000 or testing to verify its compatibility with Windows XP Tell me why j this testing is important Continue Anyway Continuing your installation of this software may impair or destabilize the correct operation of your system Windows XP either immediately or in the future Microsoft strongly recommends that you stop this installation now and contact the software vendor for software that has passed Windows Logo testing Continue Anyway STOP Installation Windows 2000 XP Click Finish to complete the installation Windows 98 SE Me Click Finish to restart the computer Save your work and close all programs Turn off the computer and peripheral devices such as the printer Then disconnect the computer power cord from the power source Ground yourself by wearing an anti static wrist strap or touching a metal
Download Pdf Manuals
Related Search