Zanussi ZT 685 Instruction Booklet
Contents
1. ZANUSSI 152989 03 1 INSTRUCTION BOOKLET A Important safety information It is most important that this instruction book should be retained with the appliance for future reference Should the appliance be sold or transferred to another owner or should you move house and leave the appliance always ensure that the book is left with the appliance in order that the new owner can get to know the functioning of the appliance and the relevant safety information This information has been provided in the interest of your safety You MUST read it carefully before installing or using the appliance Installation This appliance is heavy Care should be taken when moving it It is dangerous to alter the specifications or attempt to modify this product in any way Care must be taken to ensure that the appliance does not stand on the electrical supply cable Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person Any plumbing work required to install this appliance should be carried out by a qualified plumber or competent person Child Safety This appliance is designed to be operated by adults Children should not be allowed to tamper with the controls or play with the product Keep all packaging well away from children Keep all detergents in a safe place out of children s reach During Use Items that are contaminated by petrol paint steel2. Normal soil Cold prewash NORMAL Crockery and ON NORMAL 25g 5g a wash 100 o 65 c 1 cold rinse 65 cutlery OFF 1 hot rinse up to 65 C Thermal dry Cold sh BIO Normal soil ON BIO 25 5 Man whom to 50 C 50 c Crockery and OFF 50 g g 1 cold rinse cutlery 1 hot rinse up to 65 C Thermal dry 1 QUICK Light soil Main wash up to 50 C a Crockery and Lu a 25 g 1 cold rinse 5 cutlery c 1 hot rinse up to 55 C Testing programme according to IEC 436 DIN 44990 Programme NORMAL 65 c with detergent type A and programme BIO 50 c with detergent type B Standard place settings 12 Rinse aid selector on position 3 Recommended quantity of detergent 25 g in the dispenser 5 g in the SID This is a special programme for quick washing approx 40 minutes a full load of lightly soiled crockery etc 15 PWP09UK Operating sequence L Check the filters Ensure they are clean and properly positioned see cleaning instructions Check that there is rinse aid and salt Load the dishes Remove any scraps of food Pull the lower basket out and arrange the saucepans plates and cutlery in it Pull the upper basket out and arrange the plates saucers glasses and cups etc in it Slide the basket back into the machine Ensure that the spray arms can rotate freely Measure out detergent Add the required amount of detergent into the dispenser according to the Washing programmes chart and close the lid Close th
3. Only ASTA or BSI fuses should be used The plug must not be used if the fuse cover carrier is lost The cover carrier is indicated by the coloured insert at the base of the product A replacement cover carrier must be obtained from your local Service Force Centre This appliance complies with the following E E C Directives 73 23 or 19 2 73 Low Voltage Directive and subsequent modifications 89 336 or 3 5 89 Electromagnetic Compatibility Directive and subsequent modifications 26 CE03 YELLOW CORD CLAMP PWAO2UK Building in This dishwasher is designed to be fitted under a kitchen counter or worksurface It is essential that the recess dimensions indicated in the diagram are followed No further openings for venting of the dishwasher are required but only to let the water fill and drain hose and power supply cable pass through The recess height may be anywhere between 820 and 880 mm from the floor as the dishwasher incorporates adjustable feet max 60 mm A distance of 2 mm should be allowed between the top of the dishwasher and the counter top Adjusting the height of the appliance To adjust the height proceed as follows 1 Loosen or tighten the two front feet 2 The rear foot is adjusted by turning the screw in the middle of the front kick plate to the left or right A pad is supplied for the rear foot to make sliding the appliance in and out of the recess easier
4. or iron debris corrosive acidic or alkaline chemicals must not be washed in this dishwasher Under no circumstances should you open the door whilst the appliance is in operation Always turn off the appliance before opening the door Only use detergent specifically designed for use in dishwashers Long blades knives stored in an upright position are a potential hazard Long and or sharp items of cutlery such as carving knives must be positioned horizontally in the upper basket When finishing loading or unloading close the door as an open door can be a hazard Do not sit or stand on the open door m Isolate the appliance from the power supply and turn off the water supply after use Care should be taken when cleaning the bottom door seal and hinge area as any exposed metal edges may cut if care is not taken This product should be serviced by an authorised Service engineer and only genuine spare parts should be used Under no circumstances should you attempt to repair the machine yourself Repairs carried out by inexperienced persons may cause injury or serious malfunctioning Contact your local Service Force Centre Always insist on genuine spare parts Conservation In the interest of the environment Materials marked with the symbol Z5 are recyclable Check with your local Council or Environmental Health Office to see if there are facilities in your area for re cycling this appliance When the appliance
5. required detergent in the SID located in the centre of the upper basket Insufficient quantities of detergent will produce poor washing results whereas an excessive amount of detergent will not improve washing results and is also wasteful Using no more than the correct amount also contributes to reducing pollution PUDO4UK Compact detergents with enzymes In these compact powders the environmently unfriendly components have been replaced by natural enzymes and other more biodegradable substances The enzymes deploy their full dirt dissolving power at a temperature as low as 50 C By choosing the Bio programmes you can therefore achieve the same cleaning results that would otherwise be achievable only with 65 C programmes and conventional detergents For best results we recommend the use of Finish detergents rinse aid and salt O LL DISHWASHER SALT DE15 10 PUD03UK Using your appliance Loading your appliance Before placing dishes in the machine remove any scraps of food to avoid clogging the filters and consequently reducing the performance Do not load very small items which can fall through the baskets Open the door and slide out the baskets to load the dishes The lower basket mm The lower basket is designed to take saucepans lids J plates up to 27 cm in diameter salad bowls cutlery MN
6. 4 25 26 27 27 28 29 30 30 PCO07 1UK Description of the appliance San A Un U N Lm Levelling spacers Upper basket stop Upper spray arm Salt container Large filter Detergent dispenser Control panel Rating plate 9 Rinse aid dispenser 10 Central filter 11 Lower spray arm 12 Upper basket 13 SID Super Intensity Dispenser PDA07 1UK The control panel DI bo ON OFF In this fully integrated appliance the controls are located on the top of the door When selecting a programme the door needs to be open Audible signals have been introduced to help indicate which operations the dishwasher is performing Short signal instruction accepted When any of the buttons are pressed a short audible signal informs you that the machine has accepted the instruction given Long signal programme starting A continuous audible signal lasting about one second heard only when you close the dishwasher door informs you that the washing programme is starting Intermittent signal end of programme An intermittent audible signal lasting for approximately five seconds informs you that the wash programme has finished If you wish to deactivate these audible signals press both the NORMAL 65 c and BIO 50 c programme buttons together for about 3 seconds until the intermittent audible signal can no longer be heard INTENSIVE NORMAL BIO QUICK B
7. 7 8 20 1 YES 18 28 21 40 2 YES 29 42 41 60 3 YES 43 63 61 80 4 YES 64 84 81 120 5 YES factory setting Level 1 RINSE AND HOLD programme button Level 2 INTENSIVE 70 c programme button Level 3 NORMAL 65 programme button Level 4 BIO 50 programme button Level 5 QUICK 50 programme button INTENSIVE NORMAL BIO QUICK E 70 m 65 Bi 50 B 50 0235 PBU04UK Filling with salt If your water is level 0 it is already soft and therefore there is no need to use salt In this case the salt refill indicator light will remain illuminated Salt must be used from level 1 upward Only use salt specifically designed for N use in dishwashers All other types of salt not specifically designed for use in dishwasher especially table salt will damage the water softener Only fill with salt just before starting one of the complete washing programmes not the Rinse and Hold programme This will prevent any grains of salt or salty water which may have been spilled remaining on the bottom of the machine for any period of time which may cause corrosion 1 To fill 1 To fill with salt unscrew the cap of the salt container 2 Pour about 1 litre of water inside the container or until it is full this is necessary only before filling with salt for the first time 3 Then using the funnel provided pour in the salt until the container is full appr
8. 70 Bi 65 Bi 50 Bi 50 ES ES To reactivate the audible signals press both buttons together again for about 3 seconds until an intermittent audible signal is heard RINSE amp HOLD INTENSIVE NORMAL BIO QUICK END OF mx Wc E 65 c m 50 m 50 HI CYCLE 1 On Off pushbutton Depress this button to switch the dishwasher on The On Off indicator light illuminates indicating that the washing programme can be selected and started Depress again this button to switch the appliance off 2 Salt refill indicator light This illuminates when the salt container needs refilling This light will remain on if salt is not added for example in a soft water area where salt is not required 3 On Off indicator light 4 Programme selector buttons Depress the button corresponding to the desired washing programme see Washing programmes chart 5 End of cycle indicator light This light flashes when the programme has finished To switch it off depress the On Off button PCPIIUK Before use Before using your dishwasher for the first time uz ensure that the electrical and water connections comply with the installation instructions m remove all packaging from inside the appliance pz setthe water softener m gt fill the salt container pz fillthe rinse aid dispenser Setting the water softener The dishwasher is equipped with a water softener designed to remove minerals and salts from the water supply whic
9. To fit the pad press it onto the rear foot If required the dimensions of this pads can be reduced by breaking it where marked Good levelling is essential for correct closure and sealing of the door When the appliance is correctly levelled the door will not catch on the levelling spacers either side of the cabinet If the door does not close correctly loosen or tighten the adjustable feet until the machine is perfectly level 27 1152 IN11 IN12 PFI20UK The furniture door The door on this appliance is designed for the overlay of a panel having the following dimensions Width 596 mm Height 664 724 mm max Thickness 20mm max Weight 2 7 5 kg max The panel height should be no more than indicated otherwise complete opening of the door will no longer be possible as the panel hits against the dishwasher plinth Mounting the furniture door onto the door The height of the panel depends on the height of adjacent kitchen units see kitchen plinth adjustment The panel must be fitted with a handle as the dishwasher handle will be hidden by the panel Drill the panel with a 2 x 14 bit according to the dimensions indicated in the figure Screw the two fastening pivots in the holes indicated in the figure Mount the decor panel by inserting the two fastening pivots into the slotted holes of the door Lift the decor panel until perfect alignment with the
10. auc T a etc Al i cd Serving dishes and large lids should be arranged around Il NEM N A hep the edge of the basket ensuring that the upper spray arm AWER SAEK can turn freely m The two rear rows of prongs on the lower basket can be easily lowered to allow you to load pots pans and bowls Slightly pull them upward and let them drop Wr il 7 KJ Nl down see picture LY NI MIA N Wee Vl N Ec To bring them back to the standing position just E pull them up again N UL 11 PBA10UK The cutlery basket AN Long bladed knives stored in an upright position are a potential hazard Long and or sharp items of cutlery such as carvings knives must be positioned horizontally in the upper basket Take care when loading or unloading sharp items such as knives Cutlery should be placed in the removable cutlery basket with the handles facing downwards If the handles protrude from the bottom of the basket obstructing the lower spray arm load the cutlery with the handles facing upwards Mix spoons with other cutlery to prevent them from sticking together Silver cutlery tends to go black if mixed with steel cutlery Place it in the cutlery basket separate from the others The cutlery basket is in two parts which can be separated to give greater loading flexibility To separate the two parts slide them horizontally in opposite directions and pull the
11. d spilt during filling with an absorbent cloth to avoid excess foaming during the next wash Adjusting the dose According to the finish and drying results obtained adjust the dose of rinse aid by means of the 6 position selector C position 1 minimum dosage position 6 maximum dosage Start from position 3 Gradually increase the dose if there are drops of water or lime spots on the dishes after washing Reduce it if there are sticky whitish streaks on the dishes BROL PFROIUK Use of detergent Only use detergents specifically designed for use in dishwashers We recommend the use of Finish detergents which are available in the following options Finish Double Action Tablets Each tablet has the exact amount of detergent required simply place in the dispenser Finish Powder recommended for every day use Finish Liquid Gel ideal for every day use As the gel is extra gentle is it recommended for fine bone china To fill the dishwasher with detergent proceed as follows 1 Open the dispenser lid by pulling the catch D 2 Add the detergent according to the recommendations in the programme chart As all detergents are not the same you should also consult the instructions on the packet To help correctly dose the right amount of detergent inside the container there are two reference marks MIN 15 ml MAX 30 ml Always close the lid If the programme has a prewash add the
12. duct is installed taking in account regulations in your new country Before you move please contact your nearest Customer Care centre listed below to give them details of your new home They will then ensure that the local Service Organisation is aware of your move and able to look after you and your appliance France Senlis 33 0 44 62 29 99 Germany Nurenberg 49 0 911 323 2600 Italy Pordenone 39 0 1678 47053 Sweden Stockholm 46 0 8 738 79 50 UK Newbury 44 0 1635 521313 22 PSNO7UK Installation instructions Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person Any plumbing work required to install this appliance should be carried out by a qualified plumber or competent person Ensure the machine is easily accessible for servicing when installed Technical specifications Electricity DIMENSIONS Width 59 6 cm Height 81 8 87 8 cm Max depth 55 cm Max depth with open door 111 4cm ELECTRICAL CONNECTION Voltage 220 240 V 50 Hz MOTOR RATING DURING WASH 200 W POWER OF HEATING ELEMENT 2100 W OVERALL POWER 2300 W WATER SUPPLY PRESSURE Minimum 50 kPa 0 5 bar Maximum 800 kPa 8 bar CAPACITY STANDARD IEC PLACE SETTINGS 12 CONSUMPTION Water 191 1 4kW h 23 PTS09UK Remove all packaging before positioning the machine If possible position the machine next to a water tap and a drain Water supply c
13. e detergent dispenser lid Select the programme The selection of a programme occurs with the door partially opened Depress the On Off button the On Off indicator light comes on Depress the programme button which corresponds to the washing programme you wish to select the corresponding indicator light will flash Start the programme Close the dishwasher door An audible signal of about 1 second advises you that the programme has started The indicator light which corresponds to the programme under way is now permanently on 9 10 11 A At the end of the washing programme The dishwasher will automatically stop and an intermittent audible signal of about 5 seconds informs you that the programme has finished Wait until the end of the signal before opening the door Switch off the dishwasher Open the door The End of cycle indicator light flashes Depress the On Off button to switch the dishwasher off Cancel the wash programme To change a wash programme in progress depress the button corresponding to the programme you wish to cancel for about 1 second until the relevant control light goes out The dishwasher is now reset and you can select a new programme In general it is not advisable to open the door while the machine is working If the door is opened however a safety device ensures that the machine stops Care must be taken if the door is opened during the hot phase or immediately a
14. f the appliance i The dishwasher must not be used without filters Incorrect repositioning and fitting of the filters will produce poor washing results Cleaning the filters is vital to ensure correct operation of the machine 17 PMC04UK Check that the SID is not clogged with detergent residue If necessary rinse it under running water after having removed it from the basket by twisting it anticlockwise and pulling it upwards Fasten it back onto the support by turning it clockwise Never use your dishwasher without the SID dispenser External cleaning Clean the external surfaces of the machine and control panel with a damp soft cloth If necessary use only neutral detergents Never use abrasive products scouring pads or solvent acetone trichloroethylene etc Prolonged periods of non operation If you are not using the machine for any period of time you are advised to 1 Unplug the appliance and then turn off the water 2 Fill the rinse aid dispenser 3 Leave the door ajar to prevent the formation of any unpleasant smells 4 Leave the inside of the machine clean Frost precautions Avoid placing the machine in a location where the temperature is below 0 C If this is unavoidable empty the machine close the appliance door disconnect the water inlet pipe and empty it Moving the machine If you have to move the machine moving house etc 1 Unplug
15. fascia panel is obtained Once the correct position has been found open the door and fasten the decor panel by means of the six 4 x 40 screws provided using the holes through the inner door 28 596 max 187 1192 1179 PFI16 1UK Securing to the adjacent units To prevent the dishwasher tilting it must be secured to either the worktop or adjacent kitchen cabinet wall using the brackets supplied Insert the two fixing brackets into the slots provided in the top front part of the dishwasher as shown in the figure Secure the brackets to the adjacent units with the 3 5 x 16 screws using the upper or the side holes The appliance must be secured to the underside of the underside of the worktop using the brackets provided Failure to do this could cause damage or injury 29 PFI14 1UK Noise protection Adhesive noise protection ensures excellent noise insulation This should be fitted when the dishwasher has been mounted in the recess and the height adjusted Apply the protection as shown in the drawing making sure that the non adhesive section reaches right down to the floor Kitchen plinth adjustment To allow correct opening of the door it is sometimes necessary to cut the kitchen plinth Refer to the cutting table According to dimensions a and b as shown on the figure you will find on the following table the depth x
16. filters are not in position Not enough detergent has been used or it is unsuitable The detergent is old or has gone hard The salt container cap is not properly closed The washing programme selected is too gentle Visible lime deposits or white film on the dishes m The rinse aid has run out or too little is being used Check that there is salt and that the salt cap is tight m Ensure the water softener has been adjusted to suit the water hardness in your area The dishes are not quite dry m The dishes have been left too long inside the machine 20 PSNO9UK If after all these checks the problem persists contact your local Service Force Centre quoting the model and serial number This information can be found on the rating plate located on the right hand side of the dishwasher door see picture Service and spare parts In the event of your appliance requiring service or if you wish to purchase spare parts please contact your local Zanussi Service Force Centre by telephoning 0990 929929 Your telephone call will be automatically routed to the Service Centre covering your post code area Service Centre addresses can be found in the accompanying Customer Care book Before calling out an engineer please ensure you have read the details under the heading Something Not Working and have the model number and purchase date to hand In guarantee customers should ensure that the check
17. fter a programme has finished as steam may escape When the wash programme has finished it is recommended that the dishwasher is unplugged and the water tap turned off POS06UK Maintenance and cleaning Internal cleaning Ensure that the seals around the door the detergent and rinse aid dispensers are cleaned regularly with a damp cloth We recommend the use of Finish Dishwasher Cleaner every 3 months or run a 65 C wash without dishes using detergent Regular use of Finish Dishwasher Cleaner cleans inaccessible parts eliminates unpleasant food odours and helps prevent the build up of limescale Cleaning the central filter After each wash Scraps of food may accumulate in the drain filter A and should be removed by rinsing the filter under running water gt To remove the drain filter simply pull it out by the handle Once cleaned refit the filter by pushing it back to its original position until it engages Cleaning the large filter Every two months If necessary clean the large filter B on both sides under running water using a brush ri To remove the large filter 1 Remove the spray arm by pulling it upwards on one side 2 Turn the column C anticlockwise by 90 and then slide out the filter 3 Once cleaned refit it following the above instructions in reverse order 4 Ensure the filter is in its original position the handle of the drain filter should be pointing towards the front o
18. h would have a detrimental or adverse effect on the operation of the appliance The higher the content of these salts the harder your water is Water hardness is measured in equivalent scales Clarke degrees and French degrees The softener should be adjusted according to the hardness of the water in your area Your local Water Authority can advise you on the hardness of the water in your area If your water is level 0 it is already soft and therefore there is no need to use salt In this case the salt refill indicator light will remain illuminated The dishwasher is factory set at level 2 If this level is not suitable for your area the softener should be adjusted You may change the factory setting level setting by means of the wash programme selector buttons Each button corresponds to a different level see chart t To select a different level proceed as follows Press the NORMAL 65 c and QUICK 50 c programme buttons simultaneously for about 5 seconds until the short signal instruction accepted is heard The pilot light corresponding to the current level level 2 flashes very rapidly Press the programme button corresponding to the required level 5 seconds after having last pressed any of the programme buttons the dishwasher memorises the level selected and returns to the programme setting mode Water hardness Use Clarke French Level of degrees degrees salt 0 75 0 7 0 NO 6 1
19. hall become the Company s property This guarantee is in addition to your statutory and other legal rights Home visits are made between 8 30am and 5 30pm Monday to Friday Visits may be available outside these hours in which case a premium will be charged Exclusions This guarantee does not cover Damage or calls resulting from transportation improper use or neglect the replacement of any light bulbs or removable parts of glass or plastic Costs incurred for calls to put right an appliance which is improperly installed or calls to appliances outside the United Kingdom Appliances found to be in use within a commercial environment plus those which are subject to rental agreements Products of Zanussi manufacture which are not marketed by Zanussi European Guarantee If you should move to another country within Europe then your guarantee moves with you to your new home subject to the following qualifications The guarantee starts from the date you first purchased your product The guarantee is for the same period and to the same extent for labour and parts as exists in the new country of use for this brand or range of products This guarantee relates to you and cannot be transferred to another user e Your new home is within European Community EC or European Free Trade Area The product is installed and used in accordance with our instructions and is only used domestically i e a normal household The pro
20. he diameter of the hose provided Likewise the internal diameter of the couplings used for connections to the waste outlet must be no smaller than the diameter of the hose provided The sink plug must not be in place when the machine is draining as this could cause the water to siphon back into the machine 25 min 30 cm PWA04UK Electrical connection N this appliance must be earthed The manufacturer declines any responsibility should this safety measures not be observed If the plug that is fitted to your appliance is not suitable for the socket it must be cut off and the appropriate plug fitted Important The wires on the mains lead are coloured in accordance with the following code Green and Yellow Earth Blue Neutral Brown Live If you fit your own plug the colours of the wires in the mains lead of your appliance may not correspond with the markings identifying the terminals in your plug Proceed as follows 1 Connect the Green and Yellow earth wire to the terminal in the plug which is marked with the letter E or the earth symbol or coloured green and yellow 2 Connect the Blue neutral wire to the terminal in the plug which is marked with the letter N or coloured black 3 Connect the Brown live wire to the terminal in the plug which is marked with the letter L or coloured red The plug moulded onto the lead incorporates a 13amp BSI362 fuse
21. is to be scrapped cut off the power supply cable and make the door closing device unusable to prevent young children from being trapped inside Help to keep your country tidy use authorised disposal sites for your old appliance PSIOIUK Contents For the user Important safety information Guide to use the instruction book Description of the appliance The control panel Before use Setting the water softener Rinse aid Use of detergent Using your appliance Loading your appliance Adjusting the height of the upper basket Hints and tips Washing programmes Operating sequence Maintenance and cleaning Internal cleaning Cleaning the central filter Cleaning the large filter External cleaning Prolonged periods of non operation Frost precautions Moving the machine Something not working Service and spare parts Guarantee Conditions G Ana ta A WO N 11 13 14 15 16 17 17 17 17 18 18 18 18 19 21 22 For the installer Installation instruction Technical specifications Water supply connections Water outlet connection Electrical connection Building in Adjusting the height of the appliance The furniture door Securing to the adjacent units Noise protection Kitchen plinth adjustment Guide to use the instruction book The following symbols will be found in the text to guide you throughout the instructions N Safety instructions 13 Step by step instructions i Hints and tips 23 23 2
22. it 2 Turn the water tap off 3 Remove the water inlet and discharge hoses 4 Pull the machine out together with the hoses Avoid over tilting the machine during transport 18 PMCOSUK Something not working Certain problems are due to lack of simple maintenance or oversights which can be solved easily without calling out an engineer Before contacting your local Service Force Centre please carry out the checks listed below The dishwasher is fitted with a number of alarm systems which can help you quickly determine the cause of any problems If the On Off indicator light on the control panel is off and you see the following signals carry out the suggested corrective action switch off the dishwasher switch back on and start the wash programme If the fault code reappears contact your local Service Force Centre Important If you call out an engineer to a fault listed below or to repair a fault caused by incorrect use or installation a charge will be made even if the appliance is in guarantee Symptom Fault code Solution The machine will not start m The On Off button has not been pressed The door has not been properly closed m The plug is not properly inserted in the power socket m Check the plug fuse m There is no current at the socket The dishwasher does not Rinse amp Hold m Ensure the water tap is open fill with water programme light m Ensure the mains water supply ha
23. m apart To reassemble reverse the procedure 12 PBAIIUK The upper basket The upper basket is designed for plates dessert plates saucers dinner plates of up to 24 cm in diameter salad bowls cups and glasses Light items plastic bowls etc should be loaded in the upper basket and arranged so they do not move Arrange items on and underneath the fold down cup racks so that water can reach all surfaces For taller items the cup racks can be folded upwards Long stem glasses can then be suspended from the prongs of the cup racks Before closing the door ensure that the spray arms can rotate freely After loading or unloading your machine always close the door as an open door can be a hazard Adjusting the height of the upper basket If washing very large plates over 27 cm and up to 31 cm in diameter you can load them in the lower basket after moving the upper basket to the higher position To move to the higher position proceed as follows 1 Pull out the basket until it stops 2 Carefully lift both sides upwards until the mechanism is engaged and the basket is stable When the top basket is in the higher position it will only take plates up to 20 cm in diameter and you will not be able to use the raised cup racks To lower the basket to the original position 1 Pull out the basket until it stops 2 Carefully lift both sides upwards and then allow the mechanism to drop back down sl
24. of the cut to be made on the plinth The dimensions a and b of the table are those most frequently used in the kitchen furnitures 30 Height a Depth b 600 mm minimum gt Y 4 Dimensions of the A cut on the plinth dimensions in mm PFII7UK a 102 99
25. onnections This dishwasher must be plumbed into a cold water supply The water pressure must be within the limits given in the technical specifications Your local Water Authority will advise you on the average mains pressure in your area The dishwasher features fill and drain hoses which can be turned either to the left or the right to suit the installation The locknut must be correctly fitted to avoid water leaks Avoid bends or kinks in the hose which could prevent or slow down the water supply If the machine is connected to new pipes or pipes which have not been used for a long time you should run the water for a few minutes before connecting the inlet hose This will prevent deposits of sand or rust clogging the inlet hose filter 24 PWAOIUK Water outlet hose connection The end of the drain hose can be connected in the following ways A To the sink outlet siphon securing it if necessary with a clip B To a wall outlet provided with a vent hole minimum internal diameter 4 cm The waste connection must be at a height of between 30 cm minimum and 100 cm maximum from the floor It makes no difference which way the drain hose faces either to the right or left of the dishwasher Ensure the hose is not bent or squashed as this could prevent or slow down the discharge of water C If you use a drain hose extension it must be no longer than 2 metres and its internal diameter must be no smaller than t
26. or dishwashers The following items should not be washed in the dishwasher unless they are sold as dishwasher proof Cutlery with wooden or horn handles or glued parts bronze cutlery saucepans with wooden handles aluminium ware crystal ware leaded glass plastic items antique or fine decorated china Certain types of decoration can discolour when washed in a dishwasher Crystal ware and plastic objects if not guaranteed dishwasher proof should be washed by hand Certain types of glass can also become opaque after being washed several times in a dishwasher A chemical reaction can occur between silver cutlery and stainless steel cutlery As a precaution do not wash together Iron and cast iron objects can rust and stain other items Aluminium tends to go black copper pewter and brass tend to stain If in doubt check with manufacturer of the item When buying new dishes ensure that they are dishwasher proof PHTOIUK Washing programmes Recommended quantity Programme Degree of soil Required of detergent Cycle and ushbuttons description p in the in the type of load dispenser SID RINSE amp Partial load to be ON 1 cold rinse HOLD completed later in OFF RINSE amp HOLD the day Prewash up to 55 C INTENSIVE Heavy soil ON INTENSIVE 25g log Main wash up to 70 C o Crockery cutlery OFF 70 c 2 cold rinses ne 1 hot ri 65 C pots and pans i e up to Thermal dry
27. owly keeping hold of it Never lift or lower the basket on one side only 13 IEC 436 DIN 44990 US29 US39 PBAI4UK Hints and tips To save energy Place dishes in the machine immediately after every meal and wait until the dishwasher is full before washing If necessary run the Rinse and Hold programme see Washing Programmes chart on the following page so that any food scraps do not become caked on the dishes while you are waiting to run the complete wash programme Do not prewash dishes under running water For best washing results Before loading remove all scraps of food and soak very heavily soiled pots and pans Arrange saucepans cups and glasses etc upside down Tilt items with convex or concave surfaces so that the water drains off easily Avoid contact between the dishes as far as possible You will improve drying results by leaving the dishwasher door ajar for at least 15 30 minutes as soon as the programme finishes Wait a few minutes before removing the dishes in this way they will be cooler and the drying will be improved Empty the lower basket first and then the upper one this will avoid water dripping from the upper basket onto the dishes in the lower one Items not suitable f
28. ox 1 5 1 8 kg Do not worry if water over flows from the unit when filling with salt this is quite normal 4 Replace the cap making sure that there is no trace of salt on the screw thread or on the gasket 5 Screw on the cap tightly The salt container will require topping up periodically You are reminded of this by the Salt refill indicator light on the control panel which comes on when the salt has finished The Salt refill indicator light on the control panel can remain illuminated for 2 6 hours after the salt has been replenished assuming the dishwasher remains switched on If you are using salts that take longer to dissolve then this can take longer The function of the machine is not affected PFS06UK Rinse aid Rinse aid is automatically added during the last rinse ensuring thorough rinsing spot and streak free drying The dispenser which is positioned inside the door holds about 110 ml of rinse aid which is sufficient for 16 40 dishwashing programmes depending upon the dosage setting Filling with Rinse Aid 1 Open the container by turning the lid A anticlockwise 2 Add the rinse aid until the container is completely full approx 110 ml The indicator B will be completely dark 3 Top up the rinse aid when the indicator B becomes clear Ensure that the lid is closed after every refill Do not put liquid detergent in the rinse aid department Clean up any rinse ai
29. s not been cut off flashing very fast m The inlet hose may be squashed or bent Reposition the hose m The inlet hose may be blocked Switch off the water supply and clean the filter The filters are blocked Intensive m Clean the filters refer to Maintenance and programme light cleaning flashing very fast m The spray arms are not rotating Ensure the crockery is loaded correctly The dishwasher will not drain Quick m The drain hose may be squashed or bent programme light Reposition the hose flashing very fast m The sink may be blocked Clear any blockages m The drain hose extension is not correct Follow the instructions for connecting to the waste m There is no vent in the end of the drain hose Normal or Bio m Switch off the dishwasher Switch it back on and programme light start the programme If the alarm reappears call flashing very fast the local Service Force Centre The machine is noisy m Dishes are rattling against each other refer to Loading your machine m The spray arms are knocking against the dishes Refer to Loading your machine The door is difficult to close m The dishwasher is not level or not properly built in 19 PSNOSUK Symptom Solution The dishes are not clean poor wash The baskets are too full The dishes have not been arranged properly The spray arms do not rotate The spray arms are clogged The filters are clogged The
30. s under the heading Something Not Working have been made as the engineer will make a charge if the fault is not a mechanical or electrical breakdown Please note that it will be necessary to provide proof of purchase for any in guarantee service calls Customer Care Department For general enguiries concerning your Zanussi appliance or for further information on Zanussi products please contact our Customer Care Department by letter or telephone as follows Customer Care Department Zanussi Zanussi House Hambridge Road Newbury Berkshire RG145EP Tel 01635 521313 21 PSN06UK Guarantee Conditions Standard guarantee conditions We Zanussi undertake that if within 12 months of the date of purchase this Zanussi appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials we will at our option repair or replace the same FREE OF CHARGE for labour materials or carriage on condition that The appliance has been correctly installed and used only on the electricity supply stated on the rating plate e The appliance has been used for normal domestic purposes only and in accordance with the manufacturer s instructions The appliance has not been serviced maintained repaired taken apart or tampered with by any person not authoried by us All service work under this guarantee must be undertaken by a Zanussi Service Force Centre e Any appliance or defective part replaced s
Download Pdf Manuals
Related Search