Zanussi ZGF 643 User's Manual
Contents
1. OWER NATURAL GAS LPG G20 20 mbar 28 30 37 mbar inj 1 100 inj 1 100 g h 630 g h G31 1 Natural gas Rapid big 3 0 65 119 0 286 203 200 LPG 2 8 38 7 Building In A Auxiliary burner SR Semirapid burner R Rapid Burner These hobs can be inserted in a built in kitchen unit whose depth is between 550 and 600 mm The hobs dimensions are shown in Fig 9 Fig 9 FITTING THE LID We recommend the lid hinge block are fitted before installing the hob into the worktop To install the lid onto the hob proceed as follows a Remove the right and left hand grid blocks fitted to the back of the hob by unscrewing the relevant screws fig 10 b Fit the lid hinge blocks onto the hob using the original screws ensuring that the relevant shims are fitted between the hinge blocks and the hob fig 10 Fit the left hand lid hinge marked S into the hinge block fig 11 d Carry out the same operation with the right hand lid hinge marked 0 ADJUSTING THE LID BALANCE To adjust the lid balance turn clockwise or anti FO 2035 clockwise the central screw of the right and left hand hinges fig 12 Fig 10 FO 2037 Fig 11 INSTALLATION AND ASSEMBLY These hobs can be installed in a kitchen unit with an opening for insertion whose dimensions are shown in Fig 13 The edge of the cut out must have a minimum distance from the rear wall of 55 mm If there are side walls or side2. ZANUSSI TABLE DE CUISSON GASKOOKPLAAT GASKOCHMULDE GAS HOB 643 NOTICE D UTILISATION GEBRUIKSAANWIJZING GEBRAUCHSANLEITUNG INSTRUCTION BOOKLET ENGLISH For Your Safety These warnings are provided in the interest of safety You must read them carefully before installing or using the appliance It is most important that this instruction book should be retained with the appliance for future reference Should the appliance be sold or transferred always ensure that the book is left with the appliance in order that the new owner can get to know the functions of the appliance and the relevant warnings During Operation This appliance has been designed to be operated by adults and children under supervision Young children MUST be allowed to tamper with the controls or play near or with the oven This appliance has been designed for cooking edible foodstuff and to be used for domestic professional purposes only It must not be used for any other purpose It is dangerous to alter the specification in any way Forhygiene and safety reasons this appliance should be kept clean at all times A build up of fats or other foodstuff could result in a fire Accessible parts of this appliance may become hot when it is in use Children should be Kept away until it has cooled Under no circumstances should you attemptto repair the appliance yourself Repairs carried out by unexperienced persons ma
3. a way that the time required to move it and put it back in position exceeds thirty minutes in total the extra expenditures occurred will be billed to the owner of the appliance 8b In case of deterioration due to an irregular installation carried out in agreement with the owner of the appliance the manufacturer and the technical assistance decline all responsibility 8c Damage suchas scratches knocks or breakage of movable or dismountable units which were not notified to the manufacturer at the time of delivery are not covered by the guarantee Important notice This appliance has been made to be safe Inadequate repairs can nonetheless compromise this safety To avoid such problems and to prevent any eventual damage we advise you to have repairs carried out exclusively by qualified personnel We advise you to have repairs or maintenance carried out by the retailer or the Elgroep Service and to request only original spare parts Repairing to customer s house 02 3630444 DISTRI PARTS
4. ctioning with combustible gas lighter than alr The appliance must be electrically disconnected before all interventions If any electric supply to the appliance is required to carry out the work ensure all the necessary precautions are followed A Ramp with ending nut B Seal C Adjustable connection Fig 4 36 Electric Supply 230 V 50 Hz HOB RECESS DIMENSIONS Length 560 mm Width 480 mm GAS CONNECTION It is indispensible that the connection to the gas mains are carried out by means of an AGB tap Choose fixed connections or use a flexible pipe in AGB stainless steel If using flexible metallic pipes be careful they do not come in contact with mobile parts or they are not squeezed Use the same attention when the hob is combinated with an oven This hob can be operated by Slochteren gas G25 with a nominal pressure of 25 mbar or by natural gas with nominal pressure of 20 mbar No regulation is required for use by these two types of gas Before fitting the appliance ensure that the installation has the correct voltage forthe appliance Atfull capacity the drop in pressure must not exceed 5 Such a drop in pressure is caused by the following parameters maximum capacity of meter diameter and lenght of the tube in front and behind the meter section of transit of variuos tubes positioned on the circuit diameter of eventual connections IMPORTANT Toensure acorrect operation a savin
5. esign a lid not provided can be fitted on the hob 4 is meantto avoid dust to settle the hob when itis closed and to collect splashes of oil or fat when it is open Do not use it for any other purpose Always wipe off any splash of liquid before opening the lid Alwaysclean the from cooking residues before opening it or taking it off WARNING The crystal lid can splinter when overheated Always ensure all the burners are off before closing it 2 Cleaning and Maintenance Disconnect the appliance from the electrical supply before carrying out any cleaning or manteinance work Wash the enamelled components with warm soapy water Never use abrasive cleaners Frequently wash the caps and the crowns with hot soapy water carefully taking away any built up of food Carefully wash the stainless steel components with water then wipe them dry with a soft cloth The pan supports are dishwasher proof If the marks are particularly difficult to remove use common non abrasive cleaners or specific products Never use steel wool pads or acids In models provided with electric ignition this feature is obtained through a ceramic candle and a metal electrode fig 1 lett C Keep these components well clean to avoid difficult lighting and check that the burner crown holes lett B are not obstructed PAN SUPPORTS To keep the pan supports in the right position they are hooked to a co
6. g of energy and the long life of the appliance the voltage pressure of the appliance must correspond to the recommended values The adjustable connection is fixed to the comprehensive ramp by means of a threaded nut GJ 1 2 Interpose the sealing between the components as shown in fig 4 Screw the parts without forcing adjust the connection in the required direction and tighten everything IMPORTANT When the final connection has been made it is essential that a thorough leak test is carried out on the hob and installation Use some soapy water never a flame 5 Electrical Connection The appliance is designed to be connected to 230 V monophase electricity supply The connection must be carried out in compliance with the laws and regulations in force Before the appliance is connected 1 check thatthe main fuse andthe domestic installation can support the load see the rating label 2 check that the power supply is properly earthed in compliance with the current rules 3 check the socket or the double pole switch used for the electrical connection can be easily reached with the appliance built in the forniture unit The appliance is supplied with a connection cable This has to be provided with a proper plug able to supportthe load marked on the identification plate To connect the plug to the cable follow the recommendation given in Fig 5 The plug has to be fitted in a proper socket If connecting the applia
7. he new parts fitted on such occasion the client is entitled to repair free of charge The execution of repairs does not prolong the total period of guarantee covering the appliance 3 Technical Assistance at domicile will be provided only for large apparatus which are difficult to transport such as washing machines spin driers dishwashers refrigerators freezers vertical or horizontal ovens cookers and built in appliances 3a The above mentioned conditions are also valid for refrigerators for caravens on condition that they are situated within the national boundaries and are accessible by roads open to traffic Furthermore at the time of the intervention the appliance and its owner or the person so authorized must be present at the place agreed upon for the intervention 4 If in the opinion of the manufacturer the appliance as described in point 3 must be transported to a Technical Assistance laboratory the transportation will be carried out as established by the manufacturer at his expense and under his responsibility 5 All appliances not mentioned under points 3 and includingappliances having the same functional characteristics but whose transport is easy must be sent to the Technical Assistance or taken to them Throughout the period of guarantee the cost of return transportation will be taken care by the manufacturer 6 If during the period of guarantee a disfunction occurs due to a defect which cannot be repai
8. injectors Fig 7 and replace them with the ones required for the type of gas in use see table 2 Reassemble the parts following the same procedu re backwards e Replace the rating label placed near the gas supply pipe with the relevant one for the new type of gas supply You can find this label in the package of the injectors supplied with the appliance Should the feeding gas pressure be different or variable compared with the required pressure an appropriate pressure adjuster must be fitted on the gas supply pipe in compliance with the rules in force ADJUSTMENT OF MINIMUM LEVEL To adjust the minimum level of the burners proceed as follows e Light the burner e Turn the knob on the minimum position e Remove the knob e With a thin screwdriver adjust the by pass screw see Fig 8 If changing from natural gas to LPG completely tighten clockwise the screw until a small regular flame is obtained Finally check the flame does not go out when quickly turning the knob from the maximum position to the minimum position This procedure can easily be carried out anyhow the hob has been positioned or built in the working top Table 2 injectors suitable for G25 too BURNER NORMAL REDUCED POWER POWER kW kW Semi rapid medium Fig 7 FO 0392 By pass screw Table 1 BY pass diameters By pass Tap in 1 100 colour Auxiliary White Semi rapid Blue Rapid White Red NORMAL P
9. nce directly to the electric system it is necessary that you install a double pole switch between the appliance and the electricity supply with a minimum gap of 3 mm between the switch contacts and of a type suitable for the required load in compliance with the current rules The connection cable has to be placed in order that in each part it cannot reach a temperature 90 C higher than the room temperature The brown coloured phase cable fitted in the terminal block contact marked with L must always be connected to the network phase REPLACEMENT OF THE VOLTAGE CABLE The connection of the voltage cable to the appliance s terminal block is of type Y This means that its replacement requires the specific equipment of a technician In this case only cable HO5V2V2 F T90 must be used The cable section must be suitable to the voltage and the working temperature The yellow green earth wire must be approximately 2 cm longer than the phase wires Fig 5 To open the terminal block and reach the terminals proceed as follows insert the point of a screwdriver into the visible protrunding part of the terminal block exert a light pressure and lift Fig 6 Neutral Earth yellow green Fig 5 Fig 6 37 6 Adaptation to different types of gas INJECTORS REPLACEMENT Remove the pan supports Remove the caps and crowns e With a socket spanner 7 unscrew and remove the
10. overhating the building in should be carried out as shown in Figs 18 19 Fig 18 The hob s electric connection and the oven s one must be carried out separately both for safety reasons and to allow the oven to be easily taken off the unit Hanging forniture units or hoods must be placed at 650 mm minimum from the hob Fig 21 FO 2041 FO 2042 Fig 20 Fig 21 550 min 7 2 27222 ZOLA EA 41 GUARANTEE SPARE PARTS When calling for repairs during the period of guarantee ofthe appliance the original invoice or receipt must be shown or sent together with the appliance to be repaired General conditions of guarantee 1 manufacturer guarantees the appliance indicated on the relative invoice for a period of one year from the date of purchase In case of a fault during this period if caused bya defect in materials and or construction the client is entitled to repair free of charge 1a Concerning vacuum cleaners for domestic use the total periodof guarantee is two years Accessories are subject to adirect usage consequently these articles are excluded from the guarantee 2 The manufacturer guarantees technical assistance and repairsfor one year Spare parts fitted during repair are also covered by a one year guarantee from the date of repair In case of fault during this period as a direct result of the repair work carried out or caused by t
11. reasing the electric exhaust fan power Once you removed all packaging from the appliance ensure that it is not damaged and the electric cable is in perfect conditions Otherwise contact your dealer before proceeding with the installation The manufacturer disclaims any responsability should all the safety measures not be carried out This appliance complies with the following E E C Directives 73 23 90 683 Low Voltage Directive 89 336 Electromagnetical Compatibility Directive 90 396 Gas Appliances 93 68 General Directives and subsequent modifications These instructions are only for the countries stated by the symbol printed on the front cover of this instruction book 33 Contents 1 Instruction for the User Pag 34 5 Electrical Connection 37 2 Cleaning and Maintenance Pag 35 6 Adaptation to different types Of 38 Technical Data 36 7 Building Pag 39 4 Instruction for the Installer 36 Guarantee 42 1 Instruction for the User HOB BURNERS CONTROL KNOBS Carefully supervise cookings with fats or The hob burners control knobs are situated on the hob since these types of foodstuff can result in fire front panel The symbols on the knobs mean that if over heated is no gas suppl
12. red the appliance will be replaced free of charge Belgium Tel ELGROEP SERVICE Spare parts Electric Household Appliances Tel Bergensesteenweg 719 1520 Halle Lembeek 42 02 3630555 Fax 02 3630500 Telex 22915 eluxbe Extension of the guarantee 7 Formotorcompressors of refrigerators freezers excluding the starting device and thermal interrupter a decreasing guarantee of 20 per year for a period of five years from the date of purchase of the appliance indicated on the relative invoice with repairs free of charge throughout the entire period under guarantee On completion of the total period of guarantee the cost of travel workmanship and eventual spare parts will be at the expense of the client Exclusion from guarantee 8 Thefree execution of work for the repair and or substitution as set out above will not apply if The purchase invoice or receipt indicating the date of purchase and the identification of the appliance cannot be presented or was not sent with the appliance to be repaired The appliance is used for purposes other than those of the domestic nature for which it was made The appliance was not installed handled or used in conformity with the indications in the instruction manual or in the modalities for use The appliance has been repaired or modified incorrectly by unqualified personnel 8a the appliance has been built in underinserted suspendedor installed in such
13. s of the furniture unit near the hob the cut out edges must have a minimum distance of 100 mm as shown in Fig 13 Carry out the building in of the hob as follows put the relevant sealings supplied with the hob on the edges of the cut out as shown in Fig 14 taking care that the sealings meet without overlapping e place the hob in the cut out taking care of its centring fix the hob with the relevant screws Fig 15 traction of the screws is able to trace the sealing any excess of which can then be easily removed The edge of the hob forms a double labyrinth seal which provides a total guarantee against infiltration of liquids 40 FO 2038 Fig 13 FO 0199 a sealing POSSIBILITIES FOR INSERTION Kitchen unit with door Proper arrangements must be taken in designing the forniture unit in order to avoid any contact with the bottom of the hob which can be heated when it is operated The recommended solution is shown in Fig 16 The panel fitted under the hob should be easily removable to allow an easy access if a technical assistance intervention is needed Kitchen unit with oven The hob recess dimensions must FO 2043 comply the indication given in Figs 17 and 20 and must be a Removable panel provided with brackets to allow a b Space possibly useful for continuous supply of air connections To avoid
14. uple of special hinges in the back of the hob Thanks to these hooks you can lift the pan supports for easier cleaning as shown in fig 2 To take the pan supports completely off the hob proceed as shown in fig 3 PERIODIC MAINTENANCE Periodically ask your local Service Centre to check the conditions of the gas supply pipe and the pressure adjuster if fitted To ensure the good operation of the hob and its safety features it is necessary that the taps are periodically lubricated The periodic lubrication of the taps must be carried out by qualified personnel which you must refer to also in case of malfunctioning FO 2237 FO 2238 Fig 2 Fig 3 35 3 Technical Data Gas Burners Rating Rapid Burner big 3 kW G20 2 8 kW G30 31 Auxiliary Burner small 1 kW Semirapid Burner medium 2 kW Class 3 Appliance Category I 2E 3 Setting Natural Gas 20 mbar G25 25 mbar Gas connection G 1 2 4 Instruction for the Installer The side walls of the unit in which the hob is going to be installed must not exceed the height of the working top Avoid installing the appliance in the proximity of inflammable materials e g curtains tea towels etc The following instructions about installation and maintenance must be carried out by qualified personnel in compliance with the regulation in force The regulation to be applied for this type of installation is NBN D 51 003 Installations fun
15. y there is maximum gas supply QA there is minimum gas supply LIGHTING THE BURNERS Foreasier lighting proceed before putting pan on the pan support Push the relevant knob down and turn anti clockwise until it reaches the maximum position After lighting the flame keep the knob pushed down for about 5 seconds This will allow the thermocouple Fig 1 lett D to be heated and the safety device to be switched off otherwise the gas supply would be interrupted Then check the flame is regular and adjust it as required If you cannot light the flame even after several attempts check the cap Fig 1 lett A and the crown Fig 1 lett B are in the correct position To put the flame out turn the knob to the symbol FO 0204 Always turn the flame down or put it out before taking the pans off the burner USING THE HOB CORRECTLY To ensure maximum burner efficiency it is strongly recommended that you use only pots and pans with bottom fitting the size of the burner used so that flame will not spread beyond the bottom of the vessel see the table beside minimum maximum also advisable as soon as a liquid starts boiling to diameter diameter turn down the flame so that it will barely keep the liquid simmering Big rapid Medium semirapid Use only pans or pots with flat bottom Small Auxiliary 34 THE LID In order to make the appliance match with the kitchen d
16. y cause injury or serious malfunctioning Refer to your local Zanussi Service Centre Always insist on genuine Zanussi spare parts Ensure that all control knobs are in the OFF position when not in use Should you connect any electrical tool to a plug near this cooking appliance ensure that electric cables are not in contact with it and keep them far enough from the heated parts of this appliance If the appliance is out of order disconnect it from the electric supply MANUFACTURER ELECTROLUX ZANUSSI S p A Viale Bologna 298 47100 FORLI Italy About Installation Cleaning and Manteinance It is mandatory that all operations required for the installation are carried out by a qualified or competent person in accordance with existing rules and regulations Disconnect the appliance from the electrical supply before carrying out any cleaning or manteinance work Ensure a good ventilation around the appliance A poor air supply could cause lack of oxygen Ensure that the gas supply complies with the gas type stated on the identification label placed near the gas supply pipe Using a gas cooking appliance will produce heat and moisture in the room which it has been installed in Ensure a continuous air supply keeping the air vents in good conditions or installing a cooker hood with discharge tube In case of intensive or long time use of the appliance make the ventilation more efficient by opening a window or inc
Download Pdf Manuals
Related Search