Zanussi ZCG 7701X Instruction Manual
Contents
1. Please read the following information with care TO LOCK THE OVEN USING THE TIMER Press and hold Buttons 1 and 2 for 3 8 seconds See Fig 12 On will appear in the display See Fig 13 Press Button 2 to change the display to Of SET TIME The key symbol H appears in the display The oven will now not operate After a few seconds the time of day will show in the display Wait 3 seconds before selecting another function SET__ TIME TO UNLOCK THE OVEN Press and hold Buttons 1 and 2 for 3 8 seconds Of will appear in the display See Fig 14 Sg DI Press Button 2 to change the display to p On eo E The key symbol 7 will go out After a few seconds the time of day will show in the display The oven can now be operated normally 20 ZCG E Slow cooking The slow cook setting gives a very low heat in the oven It is particularly useful when you are cooking soups stews and casseroles because the long slow cooking will make cheaper tougher cuts of meat more tender You need to cook food at gas mark 6 for 30 minutes before you turn the oven down to the slow cook setting This makes sure that the temperature of the food gets hot enough to start the food cooking OVEN Some foods such as pastry and biscuits are not suitable for slow cooking because the temperature is too low Cover all food during cooking to prevent it from drying out You2. Drain and make the pudding in the usual way Cook for 30 minutes at gas mark 6 then reduce to the slow cook setting General points for slow cooking Frozen foods Thaw thoroughly before cooking Thickening Toss meat in flour for casseroles Alternatively blend cornflour with water and add atthe end of cooking Flavouring Flavours are retained because there is little evaporation Adjust at the end ofthe cooking time Liquid Reduce normal liquid quantities slightly as there is little evaporation during cooking time Milk and milk products for example cream Add these towards the end of cooking to prevent them from curdling Reheating Left over food should be cooled quickly and refrigerated Do not reheat food using the slow cook setting Reheat food conventionally or in a microwave Only reheatfood once 22 SE E Care and cleaning Do not use any polishes caustic cleaners abrasives washing soda or soap powder except those recommended in this booklet Please note If we recommend you use hot soapy water we mean hot A water with washing up liquid in it and not any other cleaning product If you own a dishwasher please read the operating instructions for the machine before you wash any part of your appliance in it Clean your appliance regularly using a cloth that has been wrung out in hot soapy water Rinse and polish it dry using a soft cloth Stainless Steel cream cleaners are abrasive and should be
3. Tel 08705 727727 calls to this number may be recorded for training purposes The Gas Consumers Council The Gas Consumers Council GCC is an independent organisation which protects the interests of gas users If you need advice you will find the telephone number in your local telephone directory under Gas 36 INSTALLATION INSTRUCTIONS Serial number at the front Rating Plate on top rear of panel Please note that the handle may differ in type and shape from that shown in the diagram 37 TECHNICAL DATA DIMENSIONS Height to hotplate Space for fixing at hotplate level Space for fixing above hotplate level Minimum space above hotplate Weight of appliance Minimum distance from rear wall CONNECTIONS Gas Electric GRILL Heat Input Injector Marking HOTPLATE Heat Input Injector Marking Heat Input Injector Marking Height Wiath Depth 900mm nominal 600mm nominal 600mm to front of door panel 2mm minimum clearance Flush see important note Location of Appliance page 40 787mm If a cooker hood is fitted refer to the cooker hood installation instructions 63 5kg 5mm spacer given by pressed spacer on vent panel Rear left hand side of appliance at hotplate level Re V B S P female 230V 240V 50 Hz mains 3 core cable is supplied with an integral moulded plug fitted with a 3 amp fuse Natural Gas L P Gas 2 7kW 9215 Btu h 2 45kW 176 g h 121 078 N
4. the time of day e g 15 00 To retur the timer to manual press T button 1 again See Fig 8 If using S AC OO the main oven it will come on again once button 1 has been depressed When cooking is complete remove food and turn OFF oven temperature control 18 ZUG 7701X 3 TO CANCEL THE MINUTE MINDER If you change your mind and want to cancel the minute minder Press and release button 1 Press and hold button 1 and the display will count down in one minute intervals to 0 00 See Fig 9 Release button 1 m nn Lt o Lt Ll After a few seconds the time of day will show in the display See Fig 10 H d gn If the main oven is in use this will switch OFF after a few seconds rus SET amp Q TIME Q STOP BOTH To reset press buttons 1 and 2 together See Fig 11 4 THINGS TO NOTE 1 The time of day must be set before the main oven will operate There will be a few seconds delay before the oven switches on 2 The minute minder function controls the main oven only and will Switch the oven OFF at the end of a timed period This function is useful if you want to begin cooking now and have the oven switch OFF automatically 3 If you have used the minute minder to time food cooking in the main oven you will need to reset the timer by pushing button 1 before the oven can operate again 19 ZUG ITULX 5 LOCK FEATURE MAIN OVEN ONLY
5. AND CAPABLE OF OPERATION UP TO 50 mbar AND TO CARRY A RED STRIPE BAND OR LABEL NY NS N LA 700 All dimensions in mm 5 CONNECTION TO THE ELECTRICITY SUPPLY WARNING THIS APPLIANCE MUST BE EARTHED DO NOT EARTH THIS APPLIANCE TO THE GAS BROWN BLUE GREEN SUPPLY PIPING This appliance must be connected to 230V 240V A C 50Hz supply It is supplied with 2 metres of 5 amp 3 core cable incorporating a moulded 13 amp plug fitted with a 3 amp fuse which can be plugged directly into the nearest suitable socket Ensure the plug is accessible to the user If this is not long enough the supply cable can be replaced totally by a longer cable at least 0 75mm nominal cross sectional area 24 0 2mm BROWN GREEN YELLOW IF THE MOULDED PLUG IS CUT FROM THE CABLE FOR ANY REASON IT MUST BE DESTROYED OR DISPOSED OF SAFELY AS THE PROTRUDING WIRES WILL BE AN ELECTRIC SHOCK HAZARD If any other type of plug is used it should incorporate a 3 amp fuse in either the plug or adapter or at the distribution board If the cable has to be threaded through small apertures in cabinets etc it may be disconnected from the appliance then re connected to as shown in Fig 4 Fig 4 DO NOT EXTEND THE CABLE USING PLASTIC OR CERAMIC CONNECTION TERMINAL BLOCKS AND OR INSULATION TAPE ALL EXTERNAL WIRING BETWEEN THE APPLIANCE AND THE ELECTRICAL SUPPLY SHALL COMPLY WITH LEE WIRING REGULATIONS 42 If the wiring is exten
6. Connecting to the electricity supply For your safety This appliance must be earthed and protected by a 3 amp fuse The plug supplied with the appliance can be fitted directly to a suitable three pin earthed socket Ensure the plug is accessible to the user If you have to change the fuse replace it with a 3 amp fuse which has been ASTA approved to BS 1362 Do not use the plug until you have put the fuse cover back on If the fuse cover is lost you can get a replacement from an electrical retailer The correct replacement can be identified by marking or colour coding If you cut the plug off dispose of it safely as it will be a shock hazard if it is inserted into a 13 amp socket elsewhere in the house 31 General information ZUG IJ0LA If the ignition system doesnt work there may be a fault with the electrical supply First check the socket by trying out another piece of electrical equipment in it if that works correctly renew the fuse in the plug If the fuse keeps failing there is a fault in the appliance which must be put right Do not use a fuse with a rating higher than 3 amps Do not carry out other electrical work Unplug the appliance and tell your installer Replacing the oven light bulb You need a 25 Watt small Edison screw with a temperature rating of T300 Make sure the oven is cool before you replace a bulb Unplug the appliance Open the oven door and remove the oven shelves Place palm of hand at to
7. 3 Check the supply pressure by turning the thermostat on and one hotplate tap full on and light the appropriate burner The pressure should be either i For Natural Gas 20mbar ii For LP Gas The pressure must be set to 28 mbar for use on butane or 37 mbar for use on propane 4 Turn off the taps disconnect the pressure gauge and replace oven burner and cover ensuring that the F S D phial is correctly located into the bracket on the burner 5 Check operation of oven 7 CHECKING THE GRILL Place the grill pan containing the grid with handle attached into the grill compartment Light the grill burner by turning the grill tap to its full on position and pushing the ignition button As soon as the burner is lit the button can be released 8 CHECKING THE HOTPLATE Fit the burner crowns and caps ensuring that they are correctly seated Fit the pan supports Check each of the hotplate burners in turn by turning the hotplate tap to it s full on position and pushing the ignition button As soon as the burners are lit the button can be released 43 9 SET THE TIME OF DAY To set the clock See Fig 5 FIG 5 1 Turn on electricity supply and ensure that the thermostat is in the n nn off position D D 2 Press buttons 1 and 2 together 3 Release buttons 0 00 will appear in the display Within 5 seconds press button 2 12 00 will show in the display 1 9 4 Within 5 seconds press and hold either button 1 to de
8. 900mm 20mm L P G cookers MUST NOT be installed below ground level i e in a basement or be fitted aboard any boat yacht or other vessel uade e P2 t ALL ALS ad el dH e ae axe D Moe AA A Ale All dimensions in mm Fig 1a All dimensions in mm Fig 1b 40 INSTALLATION 1 PARTS REQUIRED The loose hotplate parts are packed in the polystyrene fitment on top of the hotplate 2 LEVELLING THE APPLIANCE If the appliance requires levelling or its height adjusting from the hotplate to any working surface the procedure below must be followed 1 Adjustment to suit floor conditions or height is obtained by rotating clockwise or anticlockwise the feet at the front and rear of the appliance 2 A spirit level should be placed on one of the oven shelves to confirm the appliance is correctly levelled 3 FITTING THE STABILITY BRACKET It is recommended that if the appliance is to be installed with a flexible supply pipe a stability bracket SK 4729 A is fitted and is available from your supplier see Important Safety Requirements page 39 These instructions should be read in conjunction with the leaflet packed with the stability bracket 1 Place the appliance in its intended position and level appliance 2 Mark off 300mm from the left hand side of the appliance as shown in dimension A Fig 2a This is the centre line of the fixing bracket 3 Draw a line 100mm from the front edge of
9. a door that opens directly to the outside no air vent is required For room volumes that exceed 11m no air vent is required If there are other fuel burning appliances in the same room BS 5440 Part 2 Current Edition should be consulted to determine the requisite air vent requirements Prolonged intensive use of the appliance may call tor additional ventilation for example opening a window or more effective ventilation for example increasing the level of mechanical ventilation where present 39 LOCATION OF APPLIANCE This appliance must not be installed in a bed sitting room of volume less than 20m or in a bathroom shower room or garage It is essential that the appliance is positioned as stated below see Fig 1a i e shelves wall cabinets and cooker hoods must be fitted a minimum of 787mm directly above the top of hotplate and 400mm above the hotplate when fitted in line with the outside of the appliance If the units are intended to be fitted adjacent to the appliance but less than 400mm above the hotplate then a minimum space of 100mm must be maintained between the sides of the unit and the appliance see Fig 1b Curtains must not be fitted immediately behind the appliance or within 150mm of the sides of the hotplate If fitted next to or between two base units a minimum space of 1mm must be left between each unit and the sides of the appliance The levelling feet fitted to the appliance will achieve a nominal height to hotplate trims of
10. by any person not authorised by us All service work under this guarantee must be undertaken by a Service Force Centre Any appliance or defective part replaced shall become the Company s property This guarantee is in addition to your statutory and other legal rights Home visits are made between 8 30am and 5 30pm Monday to Friday Visits may be available outside these hours in which case a premium will be charged Exclusions This guarantee does not cover Damage or calls resulting from transportation improper use or neglect the replacement of any light bulbs or removable parts of glass or plastic Costs incurred for calls to put right an appliance which is improperly installed or calls to appliances outside the United Kingdom Appliances found to be in use within a commercial environment plus those which are subject to rental agreements Products of Zanussi manufacture which are not marketed by Zanussi ZCG 7701X 311587407 46 NOTES 4 ZANUSSI 55 77 HIGH STREET SLOUGH BERKSHIRE SL1 1DZ TELEPHONE 0870 5 727727 http www zanussi co uk Part Number 311587407 CE Electrolux plc 2002 Hi From the Electrolux Group The world s No 1 choice The Electrolux Group is the world s largest producer of powered appliances for kitchen cleaning and outdoor use More than 55 million Electrolux Group products such as refrigerators cookers washing machines vacuum cleaners chain saws and lawn mowers are sold each year to a v
11. si POY SUA usu ueo aun JO INO Aen dq eun e e ue NOA KO upoo amp uunp punar Ser au dems SIS JO Sayyed ep uexe KOL STUER JILL JO Ae euo uey aau Oupjooo aie nof JI Seynuuu OZ 104 PEQESY Gud usse seu I Jae uso SLA ur upoo 49 ae supna eseu p yeya Burjooo uaAQ Z CG7701X sut GE OZ vz v uuu eoe suu oe OZ vz v LIST upmpues SUD sutu OZ OT det L SUS suU se ST vz S SPIO eUS nUT v v 2 ULU OST euepely noue AZ v c uuu soc SNU Z v c Z ULUO8T Ny Upra SINOU G 7 v c 8 DIED saugsuq E Ge SULU GZ ST c L P O SULU oe SZ c L Sei Duppnd AUSPOA CIL xA Leen JO Suu GT OT EPO ue MO pl e JO IOJ LAM DOO SLA JACO NOK J ano DEA bal e ui Gunseoi uedo Joy aue anoge unb supay uey upoo apq suf LEO mep Ajfonaiou Hums Bupn pu 3406 9 egeo yng anoge se SECH Anpod payms AIL GA d uu GZ v S Duippnp pue gt pnq SULU GT pue OI E pA Jed suL Sr Sp v SOOT Dt ono SULU SZ pue OT Dt Jed suu se v v SQIOT S p Mop A un r SULU OZ pue IT pA Jed suu OZ v S LEO Anod aup upoo uonisod gt pau poo ageuxoddy JPUS Sec 15 usip Aue queh ppe no anq Suu GT Jo ued uedo ue ULLE IO LED sueeg peup Heos asuu noA SEN LUD A002 Buiuim ual SUA OJ 9 gt e a eonpai e g ULI SED 3e SSYNULU OT KOL peag DIE usu ION A gt x lt pm uu OZ OT zZ 48 sung pue soy SULU or OE 48 0q Z B106 0 d suuu OP OF E 48 se eo qir BGO Deag SS 3seeA ig suu o9 OS v Dote N suu o
12. the left and over the central bump on the grill pan Place the grill pan on the shelf so that the pan is positioned centrally beneath the grill burner For storage the handle should be removed from the grill pan To remove the handle slide the handle to the right and lift the handle away from the cut out on the grill pan If you require an additional handle for your grill pan this can be ordered from your local Service Force Centre by quoting part number 311479800 6 ZCG 7701X The hotplate If you have any trouble lighting a hotplate burner turn all hotplate control knobs off and make sure the hotplate burner parts have been replaced correctly See page 24 for more information Heat control The hotplate control knobs turn FRONT LEFT anticlockwise from OFF to HIGH and then to LOW You can adjust the heat by turning the control between the highest and lowest settings These are shown as a large and a small flame symbol Burner sizes The hotplate has three burner sizes to suit different types of cooking Largest burner Rapid use a large NORMAL NORMAL pan for food such as chips Medium burners Normal use for everyday cooking Small burner Simmer use for Simmering food such as soups and Stews The largest pan which you should use on any burner is 230mm 9 The base of the smallest pan should not measure less than 100mm 4 FRONKLEFT 2 ZUG 7701X For yo
13. this is quite normal and is not a fault on the appliance Heat control The grill control has two heat settings The control knob turns to the left from OFF to HIGH and then to LOW Use the high setting for fast cooking such as toast Use the low setting to cook thicker food such as chicken after you have browned it on the high setting Cooking positions There is only one position for the grill shelf Position 2 Positions are counted from the top downwards Most food should be cooked on the grid in the grill pan You can turn the grid over to suit different thicknesses of food You can place some dishes straight on to the grill Shelf This is useful when you are browning the top of food such as cauliflower cheese ZCG 7701X Preheating You don t usually need to preheat the grill You may wish to preheat it for a couple of minutes when you are cooking steak or browning food Positioning food on the grid Place food such as toast tea cakes and muffins towards the centre of the grid Place food which needs a gentle heat such as tomatoes and mushrooms towards the edge of the grid Arrange meat meat products and fish to suit their thickness and how you like them cooked The grill pan and handle The grill pan should be fitted with the handle for grilling To attach the handle place the wirework under the cut out in the pan so that the metal plate hooks over the top of the grill pan Slide the handle to
14. zz ry cooking more than one vegetable in K the same pan for example potatoes and carrots ane Kes II 5 Cut vegetables into smaller pieces This way they will cook more quickly LUE 6 A pressure cooker will save time and energy 10 ZCG 7701X The oven Before you use the oven you should wipe it out with a damp cloth to remove any dust Heat zones There are zones of heat within the oven The temperature in the middle is the gas mark you U have chosen The top of the oven is slighty PP 8s lt sessanesee hotter and the lower shelf slightly cooler The SE base of the oven is quite a lot cooler You can make use of these heat zones when you are cooking foods that need different temperatures all at the same time If you are cooking more than one tray of similar items for example cakes or biscuits swap the trays around during cooking Or you can remove the top tray when the food is cooked and move the lower tray to the higher shelf to finish cooking HOTTER toeerst KT ee COOLER Preheating You do not need to preheat the oven for casseroling and so on Preheat the oven for baking or when you are cooking sensitive food such as Yorkshire puddings souffl s and yeast mixtures When you are cooking or reheating frozen or chilled food read the instructions on the packaging When you need to preheat the oven we recommend you do so for 20 minutes Oven shelves You can slot the oven shelves int
15. All dimensions in mm f a cooker hood is fitted check the cooker hood installation instructions We recommend that cabinets fitted next to or above the appliance meet British Standards Your installer will give you advice if you are not sure Appliance dimensions Height to hotplate 898mm 920mm adjusted by four screw feet Width 600mm Depth 600mm to front of door panel 30 ZCG 7701X General information For your safety Do not block any of the appliance vents Never line any part of the appliance with foil Do not let items which can catch fire or electric mains leads such as kettle flexes trail over any part of the appliance Moving your appliance You may damage some soft or badly fitted floor coverings when you move the appliance The floor covering under the appliance should be securely fixed so it does not ruck up when you move the appliance across it Alternatively you could remove the floor covering To move the appliance open the grill door Raise the appliance off its front feet by lifting it from inside the oven Pull the appliance forward When you replace the appliance push it back to the stop and make sure there is the same gap at each rear corner For your safety Do not try to disconnect the appliance from the gas supply if the supply pipe does not have a bayonet connection as described in the installation instructions If this is the case contact the person who installed the appliance
16. INSTRUCTION BOOKLET ZANUSSI ZCG 7701X Gas Cooker Introduction ZCG 7701X Introduction This gas oven has been designed and manufactured to all the necessary British Standards It also carries the C E mark The appliance complies with European Council Directive 90 396 EEC It is important that you understand how to use and care for the oven properly before you use it for the first time We have written this booklet with your safety in mind Read the booklet thoroughly before you use the oven Keep the booklet in a safe place so that anyone who uses the oven can read it Pass the booklet on with the oven if you give or Sell it to someone else For your safety This appliance is not intended to be operated by means of an external timer or separate remote control system This oven is designed for domestic use to cook food You must not use it for any other purpose It is not designed for commercial use Keep children babies and toddlers away from the oven at all times The installation instructions that came with the oven tell you how and where it can be fitted If the oven is already installed you must make sure that all instructions have been followed If you are in any doubt ask a registered person More details on installation on page 28 We have included several drawings to show the right and wrong way of doing things The right way will have a smiling face by it A sad face shows something is wrong e RATING P
17. If the fuse blows again this indicates that there is a fault on the appliance Do not use a fuse with a higher rating than 3 amps Do not carry out further electrical work Unplug the appliance and inform your installer 34 ZCG 7701X Service and spare parts In the event of your appliance requiring service or if you wish to purchase spare parts please contact your local Service Force Centre by telephoning 08705 929929 Your telephone call will be automatically routed to the Service Force Centre covering your post code area For the address of your local Service Force Centre and further information about Service Force please visit the website at www serviceforce co uk Customers in Ireland should telephone 01 4090751 Before you call an engineer check through the information under the heading What is wrong and why When you report a problem try to describe the nature of the fault Always give your appliance s full name model and serial number Make a note of this information in this space Name Model Number Serial Number P N C Number 35 ZUG 7701X Customer Care Department For general enquiries concerning your Zanussi appliance or further information on Zanussi products please contact our Customer Care Department by letter or telephone to the address below or visit our website at www zanussi co uk Customer Care Department Zanussi 55 77 High Street Slough Berkshire SL11DZ
18. LATE This is situated on the lower front frame of the appliance and can be seen upon opening the door Alternatively the rating plate may also be found on the back or top of some models Where applicable Do not remove the rating plate from the appliance as this may invalidate the guarantee ZCG 7701X Contents Lighting the appliance The grill The hotplate The oven Oven cooking chart The electronic minute minder Slow cooking Care and cleaning Installing the appliance General information Whatis wrong and why Service and spare parts Installation Instructions Technical Data Safety requirements ventilation Location of appliance Installation Testing Guarantee conditions Notes Page 11 14 17 21 23 29 31 33 35 37 38 39 40 41 43 45 46 ZCG 7701X Lighting the appliance The system works by means of an electric spark system Details about the plug are given on page 31 Hotplate amp Grill To light 1 Push in the control knob and turn it to the large flame symbol highest setting and press the ignition button immediately When the burner has lit release the button zy FRONT LEFT o o UI ui 2 Leave the grill door open when you are using the grill Warning If the ignition button is not pressed immediately a build up of gas may cause the flame to spread Please note If you have any trouble lighting a hotplate burner turn all the hotplate control knobs off and make sure the hotplate
19. alue of approx USD 14 billion in more than 150 countries around the world
20. atural Gas R H F R H R L H R L H F 1 0kW 2 0kW 2 0kW 2 8kW 3412 Btu h 6824 Btu h 6824 Btu h 9554 Btu h 079 104 104 130 L P Gas R H F R H R L H R L H F 1 0kW 2 0kW 2 0kW 2 7kW 71 85 g h 143 7 g h 143 7 g h 194 g h 051 072 072 083 38 OVEN Natural Gas L P Gas Heat Input 2 4kW 8189Btu h 2 4kW 172 4 g h Injector Marking 108 078 Thermostat By Pass Marking 69 78 GENERAL Ignition H T Spark Spark Gap 3 4mm IMPORTANT SAFETY REQUIREMENTS This appliance must be installed in accordance with the Gas Safety Installation and Use Regulations Current Editions and the E E Wiring Regulations Detailed recommendations are contained in the following British Standard Codes of Practice BS 6172 BS 5440 Part 2 and B S 6891 All British Standards must be Current Editions PROVISION FOR VENTILATION This appliance is not connected to a combustion products evacuation device It shall be installed and connected in accordance with the current installation regulations Particular attention shall be given to the relevant requirements regarding ventilation The room containing the appliance should have an air supply in accordance with BS 5440 Part 2 Current Edition All rooms require an openable window or equivalent and some rooms will require a permanent vent as well For room volumes up to 5m an air vent of 100cm is required for room volumes between 5m and 10m an air vent of 50cm is required If the room has
21. avoided as they may damage the surface finish When you remove parts of your appliance for cleaning do not plunge them into water whilst they are very hot as this may damage the finish of the parts The hotplate Clean the hotplate top using a mild abrasive such as Cif Take care not to damage the spark electrodes If the spark electrodes are damaged the burners will not light Do not use Cif on the stainless steel finish as damage may occur You can remove the pan supports burner caps and burner crowns to clean them Again take care not to damage the spark electrodes If any food spills during cooking you can place the pan on another burner to finish cooking Then you can remove the dirty parts and clean them before the spill burns on 23 ZCG 7701X Clean the burner crowns by soaking them in very hot soapy water You can remove any stubborn stains by scouring with a soap filled pad such as Brillo If you look after the burner crowns in this way they will stay reasonably clean However the surface will dull with time Aluminium based saucepans can leave shiny metal marks on the pan supports Clean the pan supports regularly to remove the marks using a mild abrasive like Cif with a soft scourer For more stubborn marks you can use a soap filled pad such as Brillo After cleaning the appliance parts dry ze Pm them thoroughly before you put them back SE When replacing hotplate burner parts 1 Crown to body Do
22. burner parts have been replaced correctly See page 24 for more information ZCG 7701X The oven To light 1 Setthe time of day on the clock See page 17 2 Open the oven door 3 Push in the control knob and turn it to gas mark 9 After a few seconds the oven will light automatically and the oven light will illuminate OVEN H e xt CH Pa DI Ou 4 Now turn the control knob back to the gas mark you want 5 Wait until the burner is showing large flames 6 Close the oven door To turn off any burner 1 Push in the control knob and turn it to the off position This is shown by a large dot OVEN FRONT LEFT Oven light The oven light will come on when the oven burner is alight If you need to replace the oven light bulb follow the instructions given on page 32 ZCG 7701X The grill The grill is a high speed grill The instructions below tell you how to vary the heat setting and how to change the height of the grid to suit the food you are cooking You should remember to turn the food regularly You should not use the grill to keep food warm as it will continue to cook the food Prior to using the grill We suggest that you operate the grill for approximately 5 10 mins to burn off any residue from the surface During this period a slight odour may be emitted it is therefore advisable to open a window for ventilation When you first operate the grill you may hear some sounds as the burner heats up
23. can uncover food for the last half hour if it is normally served golden brown Food preparation slow cooking Joints of meat and poultry Do not cook meat joints over 2 7kg 6lb Do not cook poultry over 2kg 4lb 802 Cook on the middle shelf of the oven or above Cook stuffing separately Cook for a minimum of 6 hours Joints of pork must only be cooked if you can ensure by using a meat thermometer that an internal temperature of at least 88 C has been reached For good air circulation always stand joints on a rack in a roasting tin or casserole Thaw all frozen meat and poultry before cooking Prime cuts of meat do not benefit from slow cooking Remove excess fat and skin unless browned first Cook for 30 minutes at gas mark 6 then reduce to the slow cook setting 21 ZCG 7701X Soups casseroles and stews Do not cook casseroles over 2 7kg 6lb Bring to the boil on the hotplate then cook on slow cook Cook in the middle of the oven or above Cover food with tight fitting lid or tin foil Vegetables Cut into small pieces Dried beans must be pre soaked then boiled in an open pan for 15 minutes before adding to any dish Place vegetables under meat in casseroles Cover food with tight fitting lid or tin foil Cook for 30 minutes at gas mark 6 then reduce to the slow cook setting Milk puddings Coverthe cereal with boiling water and allow to stand for 30 minutes
24. crease or button 2 to increase the time until the correct time of day on the 24 hour clock is reached e g 14 30 10 MINUTE MINDER OPERATION To set press button 1 and the display will read 0 00 Release button 1 and press and hold button 2 The display will count up in one minute intervals until the interval to be timed is reached e g 30 minutes If necessary press and hold button 1 to achieve the correct time interval The minute minder will begin to count down once set The time of day will show in the display To show the remainder of the cook time Press button 1 At the end of the timed period the minute minder will click switching the main oven OFF if in use An audible signal will sound for up to 2 minutes The Auto symbol will flash and the cookpot symbol will go out The time of day will show in the display To stop the sound press button 1 The display will stop flashing and show the time of day e g 15 00 To return the timer to manual press button 1 again If using the main oven it will come on again once button 1 has been depressed When cooking is complete remove food and turn OFF oven temperature control 11 CHECKING THE OVEN 1 Turn the oven thermostat to Mk 9 and check that there is sparking from the ignition system This should continue until the oven burner is alight 2 When the oven burner lights up the sparking should cease there should be a low gas rate at first to the oven burner which is t
25. ded or a completely new cable fitted a 3 pin 13 amp plug should be fitted See Fig 4a Connect the wires as follows BROWN to the Live Terminal BLUE to the Neutral Terminal GREEN and YELLOW to the Earth Terminal As the colours of the wires in the mains lead which you fit may not correspond with the coloured markings identifying the terminals in your plug proceed as follows The wire which is GREEN and YELLOW must be connected to the terminal in the plug which is marked with the letter E or by the earth symbol E or coloured GREEN or GREEN and YELLOW The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK Fig 4a The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED FIT A 3 AMP FUSE TO THE PLUG HOLDER Ensure that the supply cable cannot get caught by the stability bracket Plug in the appliance 6 PRESSURE TESTING 1 The oven injector is used as a pressure test point Remove the oven furniture Remove oven burner box retaining clips one spring clip from each side and remove box front cover Replace one clip back into the right hand side of the burner box Remove oven burner by removing the spring clip from the right hand side of the oven burner and slide burner off injector whilst easing it forward and taking care not to strain the F S D phial 2 Connect the pressure gauge to the oven injector
26. he flame supervision device F S D by pass rate 3 When the F S D phial has heated up it opens the F S D valve and the main gas stream flows to the burner 4 After 1 minute check that the flame covers the full width of the burner and is stable 5 Setthe oven thermostat to Mk 2 close the oven door and check that after about 10 minutes the flame has reduced in size 6 Turn off the thermostat and check that the oven flames go out 44 12 CHECKING THE OVEN LIGHT Turn the oven thermostat knob full on and check that the oven light is operative Turn off the thermostat GENERAL NOTE Instruct the user on how to use the appliance and its ignition system Refer the user to the wording in the inside cover which gives advice on the safe operation of the appliance 45 Guarantee Conditions Standard guarantee conditions We Zanussi undertake that if within 12 months of the date of the purchase this Zanussi appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials we will at our option repair or replace the same FREE OF CHARGE for labour materials or carriage on condition that The appliance has been correctly installed and used only on the electricity supply stated on the rating plate The appliance has been used for normal domestic purposes only and in accordance with the manufacturer s instructions The appliance has not been serviced maintained repaired taken apart or tampered with
27. he locators at the bottom of the door Please note that the door glass on your product may differ in type and shape from that shown in the diagram 5 Clean the outer and inner glass using hot soapy water and mild abrasives such as Cif DO NOT try to clean the foil which is inside the door The foil is there to keep the door cool if it is damaged it will not work 6 Replace the glass by holding it in both hands and gently placing the locators into the holes of the brackets at the bottom of the door and make sure the screw location holes line up 7 Hold the glass in place with one hand and replace the cross head screws into the location holes with the other hand 8 Tighten the screws using a pozidrive screwdriver Close the door 28 ZOG 7701X Cleaning The Door Glass AN To prevent damaging or weakening the door glass panels avoid the use of the following Household detergents and bleaches Impregnated pads unsuitable for non stick saucepans Brillo Ajax pads or steel wool pads Chemical oven pads or aerosols Rust removers e Bath Sink stain removers Af the door glass panel becomes chipped or has deep scratches the glass will be weakened and must be replaced to prevent the possibility of the panel shattering Please contact your local Service Force Centre who will be pleased to advise further Installing the appliance For your safety This appliance must be installed and serviced by a competent pe
28. k o OS is reached e g 14 30 See Fig 4 Note The increase and decrease control buttons operate slowly at first and then more rapidly They 7 should be pressed separately let 17 LUG IJIULA 2 TO USE THE MINUTE MINDER IMPORTANT The minute minder can be used to time a set cooking period At the end of the cook time the minute minder will automatically switch off the main oven if in use The minute minder gives an audible reminder at the end of any period of cooking up to 23 hours and 59 minutes To set press button 1 and the display n nn will read 0 00 see Fig 5 LI o hl LI rus Release button 1 and press and hold 6 mwx Oo button 2 The display will count up in one minute intervals until the interval to be timed is reached e g 30 minutes see Fig 6 If necessary press and hold button 1 to achieve the correct time interval o OS TIME The minute minder will begin to count down once set The time of day will show in the display To show the remainder of the cook time Press button 1 At the end of the timed period the minute minder will click switching the main oven OFF if in use An audible signal will sound for up to 2 minutes The Auto symbol will flash and the cookpot symbol will go out The time of day will show in the display See Fig 7 To stop the sound press button 1 The display will stop flashing and show F G
29. not try to force the crown on to the body Make sure that the hole in the crown is over the electrode Check that the two longer location pegs sit in the slots in the body When the crown is in this position let it fall freely on to the body Check that the crown can be moved slightly from side to side s 2 Cap to crown Place cap centrally on the top of crown enamel side up Move sideways and front to back to check the cap is properly fitted 3 Check for ignition If a burner will not light then you need to check the crown and cap positions 24 ZCG 7701X The grill Do not clean the grill burner itself The burner is designed to be self cleaning Cleaning the grill may cause the holes in the burner to become blocked preventing it from operating correctly Please note that due to the nature of stainless steel the grill burner may tarnish through use over a period of time This is quite normal and is not a fault on the appliance Clean the area around the grill frequently using hot soapy water After use you can soak the pan for a few minutes and then clean it using mild abrasives or a soap filled pad such as Blo Clean the grill shelf using hot soapy water Mild abrasives can be used if necessary Grill and oven furniture Clean the grill and oven furniture frequently using hot soapy water After use you can soak the grill pan for a few minutes and then clean it using mild abrasives or a soap filled pad such a
30. o Sp v v Guppnd 6uods pajeg xadde suz Z Guppnd gt N SEO en Gupyeq uo 222d LDEALECLIDILLIU ou e a pue yey que Led IO yer jee LU e UO 00D episuepun ap uo moq Agsed dey oL SULU GZ ST v3c S nsed uep sed SUIN SULU SE SZ Z 9 Gsruxuous ed qru SULU ce GZ c 9 Gsnuauous HE eyed Seujsed eunfbuprjoo uonisod peu DO geuxaddy JESS Sec ZCG 7701X The Electronic Minute Minder 1 J DECREASE CONTROL amp MINUTE MINDER n nn LI LL 2 INCREASE CONTROL 5 COOKPOT SYMBOL The electronic minute minder can indicate the time of day operate as a minute minder and it can be used to time and switch off the main oven Please note that this is a 24 hour clock for example 2 00pm is shown as 14 00 In the following pages we explain how to use the minute minder and set the time of day Read through them until you are familiar with the procedure 1 SET THE TIME OF DAY nn When the electricity supply is first A A ohi LI switched ON the display will flash 0 00 See Fig 1 rus SET Zi Q TIME Q STOP BOTH Press buttons 1 and 2 together Release buttons 0 00 will appear in nn the display as Fig 2 Within 5 uuu seconds press button 2 12 00 will show in the display as Fig 3 2 O bere Within 5 seconds press and hold either button 1 to decrease or button dd BA 2 to increase the time until the correct time of day on the 24 hour cloc
31. o any of five positions in the oven Positions are counted a from the top downwards e For safety the shelves will only pull out so far OO AAS hes If you want to remove a shelf completely pull ee it forward as far as it will go raise the front We edge and lift it out To put the shelf into a different position keep the front edge raised slot the shelf on to the runner lower the front edge and slide the shelf in 11 The oven ZCG 7701X Baking trays and dishes For your safety Never place cooking dishes trays and so on over the oven burner This will damage the appliance as well as the cookware and possibly the floor covering underneath the appliance Leave a gap of 13mm 1 2 between all dishes and the sides of the oven so the heat can circulate properly Do not push dishes too far back as food will burn if it overhangs the burner flames For the best results from the oven we recommend that you use a baking tray which is 310mm 12 square If you use a tray or tin which is larger than this you may need to turn it around during cooking Place single dishes on the centre of the shelf You may need to turn large items around during cooking Roasting For best results we recommend open roasting using minimal fat or oil to prevent splashing It is not necessary to cover meat or poultry or wrap food in foil when roasting as this restricts the circulation of heat and will lead to extended cooktimes If you a
32. our gas supply You can do this by making sure that other gas appliances such as your central heating or gas fire are working Problem Food is cooking too quickly or too slowly Check Check that you are using the recommended gas marks and shelf positions See pages 14 16 Be prepared to adjust the gas mark up or down to get the results you want Problem The oven is not cooking evenly Check Check that the appliance is installed properly and is level Check that the main oven roof is pushed fully back into position Check that you are using the recommended size baking trays See page 12 f you are using a tin which is larger than the one we supplied be prepared to turn it round during cooking f you are cooking a large item be prepared to turn it round during Cooking 33 ZCG 7701X Problem Having difficulty cleaning any part of the appliance Check Check that the instructions for care and cleaning beginning on page 23 are being followed Problem The oven light will not work Check f the light does not work you probably need to replace the bulb To do this see instructions on page 32 Check there is not a fault with the electrical supply Check this by pressing the ignition button If you cannot hear sparking there is probably a fault First check the socket by trying out another electrical appliance in it if that works renew the fuse in the plug Use a 3 amp fuse
33. p of lens flat against oven side Use fingers to lever lens away from housing Unscrew the bulb by turning it to the left Fita new bulb and then replace the glass bulb cover Replace the oven shelves Plug the appliance back into the electricity supply he oven light bulb is not covered by the manufacturer s guarantee Ho PLACE PALM AT TOP OF LENS FLAT AGAINST OVEN SIDE USE FINGERS TO LEVER LENS AWAY FROM HOUSING ZCG 7701X What is wrong and why We strongly recommend that you carry out the following checks on your appliance before calling a Service Engineer Problem The oven grill or hotplate will not light Check f only the hotplate burners will not light make sure that the burner parts have been replaced correctly See instructions on page 24 f you cannot hear any sparking when you press the ignition button there may be a fault with the electrical supply First check the socket by trying out another piece of electrical equipment in it If that works renew the fuse in the plug Use a 3 amp fuse If the fuse blows again there is a fault on the appliance Do not use a fuse with a rating higher than 3 amps Do not carry out other electrical work Unplug the appliance and tell your installer If the appliance will not light because there is an electrical power failure such as a power cut you cannot use the main oven All other burners may be lit with a match Check that there is not a problem with y
34. re using a roasting bag or cover chicken breast with foil be prepared to allow an extra 10 15 minutes for each 1 2kg 1Ib When cooking large items such as turkeys the use of foil may be required to prevent the breast becoming dry before the rest of the bird is fully cooked 12 ZCG 7701X Condensation Condensation may form on the appliance This is quite normal and nothing to worry about The condensation forms when heat and moisture are present for example during cooking Whenever possible try to make sure that food which contains a lot of moisture for example casseroles are covered If you do notice any condensation wipe it up straight away 13 uua burjo eapg AL TOKOLDSLUKOTLESSOUANGIL Uuu Ge pue qr iz Kl suLUGE uod IR SULU oe pue IT 5izA Jed sucu oe LUnipel v S ESA pue gt pod SULU oe pue IT Biz El utu ge aud IM SULU GZ pue IT DS El sutu GZ LUnipel v S que SULU oe pue IT Biz El utu ge uod IM SULU GZ pue IT B1z4 ed SUL GZ LUnipel SULU oe pue IT 5zA Jed sutu OZ eu v S g 3eau Dee aun upoo uonisod peu poo egauroxdcy JPUS Sec Z CG7701X ures anaq oy Budd s poo Pp pap q LEO SU sase UMO NOA TS q Sup amp uprjooo pue speu sebo au e6ueu ue noA JUS 9u JO eaguso SA ul SSYsIp SA Nd QNA 3929 a aN suonisod JUS papua uuo yL EINAID qY MIL a MAPUS PAEA uonisod Jrpus euo SES Je anes SEWN upoo usiuy q Jreus ypy 24 ay Aen vo eun eau pue pe ooo
35. rson as stated in the Gas Safety Installation amp Use regulations current editions and the IEE Wiring Regulations It is important that the appliance is suitable for your gas Supply Your installer should check the rating plate Make sure that a stability bracket is fitted Location For your safety The use of a gas cooking appliance results in the production of heat and moisture in the room in which it is installed Ensure that the kitchen is well ventilated keep natural ventilation holes open or install a mechanical ventilation device mechanical extractor hood Prolonged intensive use of the appliance may call for additional ventilation for example opening of a window or more effective ventilation for example increasing the level of mechanical ventilation where present For further details see page 39 29 Installation ZCG 7701X Positioning The diagram shows how close to the appliance cupboards shelves curtains and so on can be fitted Look at the diagram and carefully read the instructions to make sure your appliance is fitted safely If you are in doubt your installer will give you advice Do not fit any materials which may catch fire for example wood or curtains behind the appliance Base units which are higher than the hotplate must be 100mm away WALL CABINETS COOKER HOODS WALL CABINETS COOKER HOOOS Doerner Ki CABINETS CURTAINS CURTAINS e 400
36. s Brillo Clean the shelf grill pan grid and handle using hot soapy water Mild abrasives can be used for the shelf if necessary The shelves grill pan and grid are dishwasher safe 25 ZCG 7701X The oven The sides and back of your oven are coated in a special material which helps to keep itself clean Follow these simple rules to maintain the appearance of the special finish aH Do not overfill dishes or they will boil over Do not put dishes too high in the oven If 2 you do they may stick tomAetoven roof 3 LED Cover your roasting tins with foil This will ect prevent fat splashing 4 Use a roasting tin which is just large L enough for the meat and potatoes This will help to reduce fat splashing 5 Ato Dry any vegetables that you are going to er EE SS roast If they are wet there will be more fat ES splashing 6 Follow the oven cleaning cycle regularly 26 ZCG 7701X Oven cleaning cycle You need to follow the cycle to keep the inside of the oven in good condition The type of cooking you do will affect how often you need to follow the cycle If you do a lot of roasting and very little other baking you should follow the cleaning cycle once a week If you do very little roasting you will only need to follow the cleaning cycle every 2 3 weeks To carry out a cleaning cycle OVEN 1 Remove the oven shelves 2 Set the oven to mark 5 for at least 30 minutes 3 T
37. the levelling feet see Fig 2a and remove appliance from its position Mark off dimension B see Fig 2a back from this line on the centre line of the bracket to locate the front edge of the lower bracket Fix lower bracket with two fixing holes to the floor then measure the height from floor level to engagement edge on back of appliance dimension C of Fig 2b 4 Assemble upper bracket to lower bracket so that underside of bracket is dimension C 3mm above floor level Reposition appliance and check that top bracket engages into appliance back as shown in Fig 2b Fig 2a Fig 2b 41 4 CONNECTING TO GAS 50 400 This appliance is designed to be installed with an appliance flexible connection only Supply piping should not be less that R3 8 Connection is made to the Rc 2 B S P female threaded entry pipe located just below the hotplate level on the rear left hand side of the appliance NOTE ONLY LIQUID SEALANTS TO BE USED WHEN INLET GAS PIPE IS FITTED TO SHUT OFF VALVE LE DO NOT USE P T F E SEALANT TAPE Check for gas soundness after connecting to the gas supply The gas bayonet connector must be fitted in the shaded area indicated in Fig 3 Take into account that it must be possible to pull the appliance forward sufficiently The hose must not get caught on the stability bracket IMPORTANT FLEXIBLE TUBING USED MUST COMPLY WITH BS 669 CURRENT EDITION L P G FLEXIBLE CONNECTIONS MUST BE OF A TYPE SUITABLE FOR L P G
38. ur safety Take care to avoid burns and scalds when you are reaching across the hotplate Use pans with flat bases They are more stable than pans which are warped Do not use pans with very heavy handles which cause the pan to tip Put pans on the centre of the burners Position pan handles so they cannot be accidentally knocked Take extra care when you are deep fat frying Do not cover the pan with a lid Do not leave a pan unattended If the pan catches fire leave it where it is and turn off all controls Place a damp cloth or a fitting lid over the pan to smother the flames Never put water on the fire Leave the pan to cool for 30 minutes If you are using a Wok we recommend it has a flat base as it will stand stable on the pan supports If you use a round based Wok with a collar support the collar must be of the open wire work type A Closed collar will affect the performance of the burner Before you use the Wok make sure that the collar is stable on the pan supports Always follow the instructions that come with the Wok The hotplate SE EIS Helpful hints E 1 n Keep flames under the base of pans If T the flames lick round the sides of the E pans you are wasting gas E 2 2 Only heat the amount of liquid you Hi need Do not overfill pans fen ut t 3 Cover pans with a lid whenever E possible The food will heat up more OI Quickly and there will be less steam in Se the kitchen 4
39. urn the temperature up to mark 7 for 2 hours or until the oven is presentably clean Some staining will remain 2 hours Do not use any cleaning EAR agents or scrapers on the P amp S inside of the oven Do not A SCH wash the special finish You can replace the oven roof if you need to You may order this from your supplier When you are ordering quote part number 359001018 General Clean the base of the oven the oven shelves the roasting tin and the oven door while they are still slightly warm This way you can easily remove any splashes or spills Wipe the oven base with a cloth that has been wrung out in hot soapy water You may use mild abrasives 2 ZCG 7701X Cleaning between the outer and inner door glass You can remove the glass from the oven and grill doors if you need to Note For grill door it is important not to open the door when the glass is removed because the door is lighter and it will spring shut To remove the outer glass 1 Open the door so you can get at the two cross head screws on the top of the door Note Open the grill door slightly to access screws 2 Loosen these two screws using a pozidrive screwdriver 3 You should hold the door glass securely in place with one hand whilst removing the screws completely with the other hand If you do not do this the door glass could fall forward 4 Using both hands gently tilt the top of the door glass towards you Lift it slightly to disengage t
Download Pdf Manuals
Related Search