Zanussi WD 1250 W Owner's Manual
Contents
1. 30 cm 12 The standpipe should have an internal diameter of approximately 38mm see diagram thus ensuring there is an air break between the drain hose and standpipe 38 mm 1 2 diameter standpipe Min 30 cm 12 When discharging into a standpipe ensure that the top of the curve in the hose end is no more than 90cm 35 4 and no less than 60cm 23 6 above floor level The upright standpipe should have a minimum length of 30cm 12 from the bottom of the elbow to the top of the pipe see diagram Make sure that it is designed in such a way that the end of the drain hose cannot be covered with water The drain hose may be extended to a maximum of 4 metres An additional drain hose and joining piece is available from your local Service Force Centre The joining piece must have an internal diameter of 18mm If you intend the drain hose to empty into a sink make sure that the sink is empty and the plug hole is not blocked Use the plastic U Piece supplied Important Before connecting up the machine to new pipework or to pipework that has not been used for some time run off a reasonable amount of water to flush out any debris that may have collected in the pipes Levelling Level the washing machine by raising or lowering the feet The feet may be tight to adjust as they incorporate a self locking2. 19 Maintenance and Cleaning Before any maintenance or cleaning is carried out you must DISCONNECT the appliance from the electricity supply Descaling The water we use normally contains lime It is a good idea to periodically use a water softening powder in the machine Do this separately from any laundry washing and according to the softening powder manufacturer s instructions This will help to prevent the formation of lime deposits After each wash Leave the door open for a while This helps to prevent mould and stagnant smells forming inside the appliance Keeping the door open after a wash will also help to preserve the door seal Maintenance Wash With the use of low temperature washes it is possible to get a build up of residues inside the drum We recommend that a maintenance wash be performed on a regular basis To run a maintenance wash e The drum should be empty of laundry e Select the hottest cotton wash programme e Use a normal measure of detergent must be a powder such as Ariel Futur External cleaning Clean the exterior cabinet of the appliance with soap and water only and then dry thoroughly Cleaning the dispenser drawer The washing powder and additive dispenser drawer should be cleaned regularly Remove the drawer by pressing the catch downwards and by pulling it out Flush it out under a tap to remove any traces of accumulated powder To aid cleaning the top part of the additi
3. of the environment e Materials marked with the symbol he are recyclable e Check with your local Council or Environmental Health Office to see if there are facilities in your area for re cycling this appliance When the appliance is to be scrapped cut off the power supply cable and make the door lock device unusable to prevent young children from being trapped inside e Help to keep your country tidy use authorised disposal sites for your old appliance How do we help to protect the environment We use recycled paper Your machine is fitted with a balance control device which ensures the machine is stable during the spin If the wash load appears not to have been spun sufficiently at the end of the wash cycle because it is not evenly distributed in the drum the balance control device may have operated It will therefore be necessary to redistribute the wash load manually and select a spin programme For more detailed information see the section headed Something Not Working Deseription of the Appliance 1 Detergent dispenser drawer 2 Control Panel 3 Door locked light 4 Door opening handle 5 Drain pump 6 Adjustable feet Door locked light It stays on during the whole programme indicating that the door is locked When the light goes out the door can be opened see page 13 Detergent dispenser drawer LI Prewash LI Main wash Fabric softener Child safety feature This machine incorporates a
4. 1 Load the laundry 2 Depress the ON OFF button to switch the machine on will show in the display 3 If you wish to carry out the electronic drying depress AUTO DRY button until the light IRON DRY illuminates COTTONS EXTRA DRY STORE DRY SOLIRON DRY SYNTHETICS STORE DRY Woon If you want a timed drying depress the DRYING TIME button until the light COTTONS lights up then depress the same button until the time you want appears on the display amp 3 COTTONS SYNTHETICS 2 Pme W 4 Press the START PAUSE button to start the programme START PAV9 14 5 At the end of the programme press SKIP RESET button to clear the memory and switch the machine off by depressing ON OFF button 6 Remove the laundry Note The programme time will automatically increase by up to 1 minute this is quite normal AUTODRYING 2 KG OF SYNTHETICS You intend to wash and dry automatically 2 kg 4 4 Ib of synthetics which do not need ironing Do not use a dosing device ball when carrying out a washing amp drying programme 1 Load the laundry 2 Add detergent and fabric softener 3 Switch the machine on by depressing the ON OFF button Q 4 Select the wash programme fabric and temperature 5 Select the drying time or degree of drying 6 Select the required options by means of the relevant buttons If possible do not select a spin speed lower than that proposed by the applianc
5. SPIN SPEED RINSE HOLD PREWASH SUPER RINSE QUICK WASH SPIN SPEED RINSE HOLD PREWASH SUPER RINSE QUICK WASH SPIN SPEED RINSE HOLD SPIN SPEED RINSE HOLD Energy Water kWh litres cae The coloured cotton programme at 60 C is the reference programme for the data entered in the energy label in compliance with EEC 92 75 standards This data is given purely as an indication the consumption values may vary in relation to the quantity and type of laundry the temperature of the water supply and the ambient temperature The data refers to the highest temperature provided for each programme 18 Drying Programmes Timed drying Degree of drying Type of fabric Spin speed Drying time mins 1200 80 90 2 5 kg 1300 75 85 Cotton and linen 1400 70 80 bathrobes bath towels etc 1200 60 70 1 5 kg 1300 55 65 1400 50 60 1200 70 80 2 5 kg 1300 65 75 Cotton and linen 1400 60 70 towels T shirts ue 5060 Store dry bathrobes Suitable for items 1 5 kg 1300 45 55 to put away 1400 40 50 without ironing fabrics jumpers blouses underwear household linen 1 kg 35 45 1200 55 65 2 5 kg 1300 50 60 Iron dry Cotton and linen 1400 45 55 Suitable for sheets tablecloths ironing shirts etc 1200 45 55 1 5 kg 1300 40 50 1400 35 45 The STORE DRY drying programme for cotton is the reference programme for the Energy Label data in compliance with EC directive 92 75
6. You must select this option after you have set the programme and before you press the START PAUSE button The time value shown on the display will decrease by one unit every hour You can change the delay time at any moment before you press the START PAUSE button If you have already pressed the START PAUSE button and you wish to change or cancel the delay time proceed as follows set the machine to PAUSE by pressing the START PAUSE button press the DELAY START button until the display shows the desired delay time or press the DELAY START button once to erase the delay time The display will indicate Oh press the START PAUSE button again Important The door will be locked throughout the delay time DOOR LOCKED light lit If you need to open the door you must first set the machine to PAUSE by pressing the START PAUSE button After you have closed the door press the START PAUSE button again 10 13 Programme phase indicator lights When you select a programme the lights relevant to the phases that form the programme light up After you have started the programme only the light relevant to the phase that is currently being carried out will remain lit i Operating Sequence WASHING Before the first wash we recommend that you pour 2 litres of water into the main wash compartment WY of the detergent drawer in order to activate the ECO valve Then run a cotton cycle at 60 C with the
7. cycle the display will still indicate the duration relevant to the maximum load The duration value will be gradually adjusted during the execution of the cycle COTTONS O SYNTHETICS DELICATES WOOL HAND O 2 WASH A4 BRIG 6 Select the temperature Press the TEMPERATURE button if you wish to select a temperature value different from the one proposed by the machine The relevant light will light up 7 Select the spin speed or the RINSE HOLD option Press the SPIN SPEED button repeatedly in order to select the desired spin speed or the RINSE HOLD option The relevant light will light up If you select the RINSE HOLD option the machine will stop at the end of the programme with the water still in the tub 8 Select the desired options If your laundry is very dirty it may be advisable to select the PREWASH option If you wish the laundry to undergo an extra rinse select the SUPER RINSE option If your laundry is only slightly soiled select the EXTRA QUICK option The relevant light illuminates O PREWASH O RISE EXTRA QUICK OPTION 12 9 Select the DELAY START Before you start the programme if you wish the starting to be delayed press the DELAY START button repeatedly or keep it pressed to select the desired delay The selected delay time value up to 24 hours will appear on the display for 3 seconds then the duration of the programme will appear again DELAY ST
8. guide you throughout the instructions A Safety instructions i Hints and tips W Environmental information G Your New Washer Dryer This new machine meets all modern requirements for effective treatment of laundry with low water energy and detergent consumption The special wool programme with its new delicate wash system treats your woollens with extreme care e The anti unbalance device ensures that the machine remains stable when spinning e Automatic cooling of the wash water to 60 C before draining with the 90 C programme This reduces thermal shock to fabrics helping to prevent creasing e The ECO valve allows total use of detergent and reduces water consumption so saving energy e The two drying programmes will give your wash that soft relaxed feel whatever the weather Y Ecological hints To save water and energy and help protect the environment we recommend that you follow these hints e Adjust the quantity of detergent according to the hardness of your water supply the amount of laundry and the degree of soiling e Select a Quick programme for lightly soiled laundry e A programme without prewash is sufficient for normally soiled laundry e Try to load the maximum drying capacity of the machine as small loads are uneconomical e Always load well spun laundry The higher the spin speed the lower the electricity consumption and the shorter the drying times Important In the interest
9. necessary wait until the water has cooled down open the pump door place a bowl on the floor and place the end of the emergency emptying hose into the bowl Remove its cap The water should drain by gravity into the bowl When the bowl is full put the cap back on the hose Empty the bowl Repeat the procedure until water stops flowing out clean the pump if necessary as previously described replace the emergency emptying hose in its seat after having plugged it screw the pump cover again and close the door Something Not Working Certain problems are due to lack of simple maintenance or oversights which can be solved easily without calling out an engineer Before contacting your local Service Force Centre please carry out the checks listed below IMPORTANT if you call out an engineer to a fault listed below or to repair a fault caused by incorrect use or installation a charge will be made even if the appliance is under guarantee During machine operation it is possible that one of the following alarm codes appears on the display E10 problem with the water supply E20 problem with water draining E40 door open Once the problem has been eliminated press the START PAUSE button Q to restart the programme If after all checks the problem persists contact your local Service Force Centre The machine does not start The door has not been closed E40 The plug is not properly inserted in the power socket There is
10. or a bar beneath the circle will indicate the required process to the dry cleaner TUMBLE DRYING with high heat setting C with low heat setting May be tumble dried X A cross through any symbol means DO NOT Important Notes For best results always use the dispenser drawer for fabric conditioner to avoid the conditioner entering the dispensing detergents and liquid additives machine prematurely Once the dispenser has been filled close it by pushing it When using liquid detergent and a prewash programme in gently This is particularly important if you are using place the detergent into the correct compartment in the dispenser drawer after the prewash has finished 17 Washing programmes Type of laundry and symbols on White cotton gt shirts blouses underwear acrylic fabrics viscose poly ester synthetic Programme temperature Synthetics 60 50 40 30 C Delicates 40 30 C Hand wash 40 30 C Description of programme Main wash at 60 90 C 3 rinses Long spin Main wash at 60 50 40 30 C 3 rinses Long spin Main wash at 60 50 40 30 C 3 rinses Short spin Main wash at 40 30 C 3 rinses Short spin Main wash at 40 30 C 3 rinses Short spin Main wash at 40 30 C 3 rinses Short spin Available options SPIN SPEED RINSE HOLD PREWASH SUPER RINSE QUICK WASH SPIN SPEED RINSE HOLD PREWASH SUPER RINSE QUICK WASH
11. remove the hooks e Close poppers and zips and fasten loose buttons It is essential to wash new coloured items separately when washing for the first time e When washing fabrics requiring different wash temperatures together always select the lowest temperature e White items should not be washed with coloured items e Very small items handkerchiefs ribbons socks etc should be washed in a washing bag or a pillow case e Use a good quality detergent suitable for automatic washing machines e Use the correct quantities of detergent e For wool use gentle detergent only in small quantities e Bleach is very corrosive it should be used with care and kept out of reach of children 15 Some stains such as fruit wine grass rust etc are difficult to remove and should be treated before washing with specific products which can be found in most household shops In some cases it may help to soak the stain before washing with a special pre soak product or biological detergent If you have used the machine to wash rinse or spin only non colour fast garments there may be dye left in the sump To ensure any subsequent wash is not contaminated with the dye select and carry out a rinse and spin programme without any garments to ensure that any dye is removed from the sump Do not leave the damp laundry load in a heap too long before drying Avoid drying dark clothes with light coloured fluffy items such as towels as th
12. the same extent for labour and parts as exists in the new country of use for this brand or range of products e The guarantee relates to you and cannot be transferred to another user e Your new home is within the European Community EC or European Free Trade Area e The product is installed and used in accordance with our instructions and is only used domestically i e a normal household e The product is installed taking into account regulations in your new country Before you move please contact your nearest Customer Care Centre listed below to give them details of your new home They will then ensure that the local Service Organisation is aware of your move and able to look after you and your appliances France Senlis 33 0 344 62 29 29 Germany Nurnberg 49 0 800 234 7378 Italy Pordenone 39 0434 39 4700 Sweden Stockholm 46 0 8 672 53 90 UK Slough 44 0 1753 219897 Ireland Dublin 353 0 1 4090751 Installation Instructions It is dangerous to alter the specifications or attempt to modify this product in any way Care must be taken to ensure that the appliance does not stand on the electrical supply cable Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person Any plumbing work required to install this appliance should be carried out by a qualified plumber or competent person Should the appliance power supply cable need to be replaced th
13. until the display shows three blinking dashes 13 How to open the door during the cycle of a programme You can open the door after having set the machine to PAUSE provided the following conditions exist the washing machine is not in the heating phase beyond 55 C the level of the water is not high the drum is not turning If these requirements are met when you pause the machine the DOOR LOCKED light goes out and the door can be opened Should it not be possible to open the door and should it be absolutely necessary to do so switch the machine off by pressing the ON OFF button 13 After approximately 3 minutes you can open the door Pay attention to the level and temperature of the water in the machine When you close the door and press the ON OFF button again the machine will resume the programme from the point where it had been interrupted 14 End of programme At the end of the programme the machine stops automatically gives an audible signal and displays a blinking zero If you had selected the RINSE HOLD option the START PAUSE button light flashes to indicate that the water must be drained The display shows a steadily lit Zero When the programme has been completed a blinking zero appears on the display and the audible signal is given The DOOR LOCKED light goes out at once Press the SKIP RESET button repeatedly to erase the programme that has just been carried out If you omit to d
14. 152992420 ZANUSSI A Electrolux WASHER DRYER WD 1250 W INSTRUCTION BOOKLET A Important Safety Information It is most important that this instruction book should be retained with the appliance for future reference Should the appliance be sold or transferred to another owner or should you move house and leave the appliance always ensure that the book is supplied with the appliance in order that the new owner can get to know the functioning of the appliance and the relevant warnings These warnings have been provided in the interest of safety You MUST read them carefully before installing or using the appliance Installation C This appliance is heavy Care should be taken when moving it It is dangerous to alter the specifications or attempt to modify this product in any way All packing and transit bolts must be removed before use Serious damage can occur to the product and to property if this is not adhered to See relevant section in instructions Any plumbing work required to install this appliance should be carried out by a qualified plumber or competent person Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person Care must be taken to ensure that the appliance does not stand on the electrical supply cable If the machine is situated on a carpeted floor please adjust the feet in order to allow air to circulate freely hild Sa
15. ART e 10 Start the programme Press the START PAUSE button The relevant light will stop flashing the DOOR LOCKED light will light up and only the light relevant to the phase that is in progress will remain lit If you have chosen a delayed start the washing machine will begin the countdown The display will show the duration of the programme or the selected delay START PAUSE l How to change a programme during its cycle Before you make any change you must pause the machine by pressing the START PAUSE button It is possible to change any phase before the programme carries it out Changing the type of fabric or temperature is possible obviously only during the washing phase When you make a change in these two parameters the machine will resume the cycle from the beginning If it is necessary to drain the water in order to change the programme in progress proceed as follows PAUSE the machine by pressing the START PAUSE button press the SKIP RESET button repeatedly until only the DRAIN light kJ remains lit press the START PAUSE button again When the water has been drained the display shows a blinking zero You may now select a new programme and press the START PAUSE button to start it 12 How to cancel a programme during its cycle To cancel a programme that is being carried out first pause the machine by pressing the START PAUSE button then press the SKIP RESET button repeatedly
16. INE DISHWASHER z e RAINWATER RUN OFF FOUL DRAIN SURFACE WATER DRAINS amp SEWERS FOUL SEWERS ie SEWAGE TREATMENT WORKS O t UNTREATED DISCHARGE y TED DISCHARGE RIVER Electrical connection Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person WARNING THIS APPLIANCE MUST BE EARTHED The manufacturer declines any liability should this safety measure not be observed Before switching on make sure the electricity supply voltage is the same as that indicated on the appliance s rating plate The rating plate is located at the top of the rim of the open door Ser No Mod Prod No The appliance is supplied with a 13amp plug fitted In the event of having to change the fuse in the plug supplied a 13amp ASTA approved BS1363 A fuse must be used Should the plug need to be replaced for any reason proceed as described below The wires in the mains lead are coloured in accordance with the following code Green and Yellow Earth Blue Neutral Brown Live GREEN amp YELLOW The wire coloured green and yellow must be connected to the terminal marked with the letter E or by the earth symbol or coloured green and yellow The wire coloured blue must be connected to the terminal marked N or colo
17. PER RINSE this option can be selected with all programmes except the wool and handwash programme The machine performs 4 rinses instead of 3 This option is recommended for people who are allergic to detergents and in areas where the water is very soft e EXTRA QUICK select this option for laundry that is only slightly soiled not for wool and HAND WASH programme The washing time will be reduced according to the type of fabric and the selected temperature The PREWASH and EXTRA QUICK options cannot be selected together 7 AUTO DRY button This button allows you to choose the required degree of drying for cottons and synthetics Extra dry only for cottons Store dry cottons and synthetics Iron dry only for cottons The drying time is automatically adjusted by the machine the laundry will be dried to the selected degree of dryness 8 DRYING TIME button By depressing this button you can select a timed programme for cotton or synthetics the relevant light illuminates To select cottons you have to push the button for about 2 seconds To select the drying time push the button until the time you want appears in the display according to the fabrics cotton or synthetics you have to dry For COTTON you can select a drying time from 10 minutes to 130 minutes 2 72 For SYNTHETICS you can select a drying time from 10 minutes to 100 minutes 1 42 Every time you press the button the time increases b
18. e this is updated every minute indicated by the message Err when a function The washing machine has stopped with water in incompatible with the current programme is selected the tub at the end of a programme with the RINSE HOLD option this is indicated by a static zero The washing machine has completed the programme this is indicated by a blinking zero At the same time the door locked light goes out The zero will reappear when you switch the washing machine on unless the previous programme has been erased by means of the SKIP RESET button Ll The incorrect selection is also indicated by an audible warning signal An alarm code indicates a fault in the machine operation see the relevant chapter on page 22 23 e 10 START PAUSE button lt gt This button has three functions e Start after you have selected the desired programme and options press this button to start the machine The light above the button will stop flashing and remain lit If you have selected a delay time by means of button 12 the countdown will begin and will be shown on the display Pause when you press this button again the programme in progress is interrupted The light above the button will start flashing To restart the programme press the button again Important You must set the washing machine to PAUSE before you make any change in the programme in progress Draining of water and spinning after the execution o
19. e or decrease the temperature if you want your laundry to be washed at a temperature different from the one proposed by the machine The relevant light will light up Maximum temperatures are 90 C for cotton 60 C for synthetic fabrics 40 C for delicate fabrics wool and fabrics to be hand washed HAND WASH programme PREWASH O COTTONS O 90 C O 1200 SYNTHETICS 60 C 900 DELICATES O 50 C 700 SURER O wol O 40 C 500 O NA O 30 C O RINSE OPTIONS DELAY WD 1250 W COTTONS O EXTRA DRY O STORE DRY O IRON DRY 7 COTTONS SYNTHETICS O STORE DRY O SYNTHETICS O D amw ZING AW START PAUSE 7 8 9 10 111213 Important By pressing the TEMPERATURE and SPIN SPEED buttons simultaneously for 3 seconds the acoustic signal is deactivated at the end of the cycle when selecting the programmes and in case of an incorrect option selection By pressing these 2 buttons again the acoustic signal is reactivated 5 SPIN SPEED button Press this button repeatedly to change the spin speed if you want your laundry to be spun at a speed different from the one proposed by the machine The relevant light will light up Maximum speeds are e for cotton 1 200 rpm e for synthetic fabrics wool and fabrics to be hand washed 900 rpm e for delicate fabrics 700 rpm RINSE HOLD position when you choose this option the machine will not drain the water of the la
20. e to avoid a too long drying time so saving energy In any case the reduction of the spin speed is only possible after selecting drying The lowest values you can select are the following 900 r p m for cottons amp synthetics with electronic drying 900 r p m for cottons and 700 r p m for synthetics with timed drying 7 Start the programme by depressing the START PAUSE button 8 At the end of the programme press the SKIP RESET button to clear the memory and press the ON OFF button again to switch the machine off 9 Remove the laundry G Washing and Drying Hints Do NOT overload the machine Weigh the laundry the first few times you use the appliance The average weights of the most common items are listed below as a guide 1000g 1 kg Sheet 700 1000 g Pillow case 100 200 g Tablecloth 400 500 g Serviette 50 100 g Tea towel 70 120 g Linen hand towel 100 150 g Towelling hand towel 150 250 g Towelling bath towel 700 1000 g Bath robe 1000 1500 g Man s shirt 200 300 g Apron 150 200 g e Load the laundry loosely alternating large items with small ones e Sort the laundry according to the type of fabric colour fastness and how dirty it is e Avoid washing unhemmed or torn items as they may unravel e Before washing empty all pockets of small objects which may have been left inside coins keys screws etc as these could damage the drain pump e When washing curtains
21. en used for normal domestic purposes only and in accordance with the manufacturer s instructions e The appliance has not been serviced maintained repaired taken apart or tampered with by any person not authorised by us e All service work under this guarantee must be undertaken by a Service Force Centre e Any appliance or defective part replaced shall become the Company s property e This guarantee is in addition to your statutory and other legal rights Home visits are made between 8 30am and 5 30pm Monday to Friday Visits may be available outside these hours in which case a premium will be charged Exclusions This guarantee does not cover e Damage or calls resulting from transportation improper use or neglect the replacement of any light bulbs or removable parts of glass or plastic e Costs incurred for calls to put right an appliance which is improperly installed or calls to appliances outside the United Kingdom 24 e Appliances found to be in use within a commercial environment plus those which are subject to rental agreements e Products of Zanussi Electrolux manufacture which are NOT marketed by Zanussi Electrolux European guarantee If you should move to another country within Europe then your guarantee moves with you to your new home subject to the following qualifications e The guarantee starts from the date you first purchased your product e The guarantee is for the same period and to
22. ener should be poured into the compartment marked with the symbol BB Follow the manufacturer s dosage instructions and never exceed the MAX level Bounce conditioning sheets for use in a tumble dryer We recommend the conditioning sheets are pinned using a safety pin to an article of laundry and placed in the tumble dryer Wash Care Symbols Wash care labels inside garments recommend how to launder your clothes with the best results The care labelling code is in line with care labelling used in the rest of Europe The symbols used make it easy to select the correct programme on your washing machine WASHING SYMBOL WASH ACTION FABRIC Normal Maximum White Cotton or Linen without Special Finishes Cotton Linen or Viscose Normal Maximum without Special Finishes Colourfast at 60 C Nylon Polyester Cotton Viscose Reduced Medium with Special Finishes Cotton Acrylic Mix Normal Maximum Cotton Linen or Viscose Colourfast at 40 C but not 60 C Acrylics Acetate Triacetate Wool SAQRR aE DEREM EB mixes Polyester wool blends Much Reduced Minimum Wool wool mixtures Silks Hand wash only Do not machine wash BLEACHING A Chlorine bleach may be used IRONING az Hot iron Cotton Linen Viscose cal Warm iron Polyester mixtures Wool co Cool iron Acrylic Nylon Polyester DRY CLEANING May be dry cleaned Other letters and
23. ergent in your everyday wash and only detergents recommended for use in automatic machines To maintain the appearance of your clothes and household textiles and to make them last longer you should use different types of detergent for different washes whether for whites colours or delicates WHITES We recommend the Ariel product range which is biological and designed to provide excellent cleaning and stain removal even at low temperatures NON BIOLOGICAL If you prefer to use a non biological detergent which does not contain enzymes we recommend Fairy Fairy provides good cleaning and stain removal COLOUREDS For coloured items you should usea my detergent which is designed to clean i while maintaining the original colour Ariel Color does not contain bleach and therefore helps to preserve colours DELICATE ITEMS When washing delicates such as woollens you should use a product which is specially designed to care for fine fabrics Dreft Automatic is suitable for woollens and other delicates AUTOMA LAUNDRY BLEACH For additional stain removal you may wish to use a product such as Ace Gentle Bleach which is used in addition to your chosen detergent Ace is suitable for all washable fabrics including silks woollens and coloureds 16 And in which form Not only are there different types of detergent but they are also available in different forms Whether you chose a powder or l
24. ese can attract the fluff If you overdry the laundry besides wasting energy any subsequent ironing may become more difficult because the fabric could be heavily crumpled Remove the laundry when the appliance has finished drying To avoid a static charge when drying is completed use either a fabric softener when you are washing the laundry or a fabric conditioner specifically for tumble dryers Particularly delicate items such as synthetic curtains woollen and silk garments with metal inserts nylon stockings bulky garments such as anoraks bedcovers quilts sleeping bags and duvets must not be machine dried Garments padded with foam rubber or materials similar to foam rubber must not be machine dried they represent a fire hazard Also fabrics containing residues of setting lotions or hair sprays nail solvents or similar solutions must not be machine dried in order to avoid the formation of harmful vapours For drying follow the indications given on the manufacturer s labels May be tumble dried Drying at high temperature Drying at reduced temperature Bl Do not tumble dry Important As a dryer the machine works on the condensation principle Therefore the water tap must be open and the drain hose must drain water into a sink or into the drain pipe even during the drying cycle Which detergent To ensure you obtain the best wash results from your appliance it is important to use the right det
25. f programmes with the RINSE HOLD option l 1 SKIP RESET button This button performs two functions Clears the memory Selects special programmes At the end of every programme the RESET button must be pressed once or repeatedly to clear the programme memory This will be confirmed by three dashes flashing in the display If the previous programme is not cleared the display will show a flashing and an audible signal will sound when you switch the machine on Selecting a special programme A wash programme must be selected in the normal way START button not pressed START PAUS A normal wash cycle consists of the following phases Wash Rinses Spin and is confirmed by the illumination of the corresponding LED s LU prewasy I LJ DRAIN ih paving To select rinse amp spin press the SKIP button once the wash LED goes out To select spin only press the SKIP button twice The wash amp rinse LED s go out To select Drain press the SKIP button three times the wash rinse spin LED s go out If you wish to cancel or advance the running programme to the required phase PAUSE the cycle and then press the SKIP button as previously described I2 DELAY START button This button makes it possible to delay the starting of the programme by up to 24 hours The delay you have selected is shown on the display for about 3 seconds afterwards the duration of the programme reappears
26. fety This appliance is designed to be operated by adults Children should not be allowed to tamper with the controls or play with the product Pets and children have been known to climb into washer dryers Please check your drum before use The glass door becomes very hot during the washing and drying cycle Keep children away from the vicinity of the appliance whilst it is in operation e Keep all packaging well away from children e Keep all detergents in a safe place out of children s reach Use Always unplug the appliance and turn off the water supply after use Do not overload the appliance See relevant section in the instruction book Only wash and dry fabrics which are designed to be machine washed and dried If in doubt consult the care label on the clothes Before washing ensure that all pockets are empty and buttons and zips are fastened Avoid washing frayed or torn articles and treat stains such as paint ink rust and grass before washing Underwired bras must NOT be machine washed Any objects such as coins safety pins nails screws stones or any other hard sharp material can cause extensive damage and must not be placed into the machine Garments which have been in contact with volatile petroleum products should not be machine washed If volatile cleaning fluids are used care should be taken to ensure that the fluid is removed from the garment before placing in the machine Wash small items s
27. formation about Service Force please visit the 5 The purchase date website at www serviceforce co uk Please note that a valid purchase receipt or For Customer Service in Ireland please contact us at the guarantee documentation is required for in address below guarantee service calls Zanussi Electrolux Electrolux Group Irl Ltd Long Mile Road Dublin 12 Republic of Ireland Tel 353 0 1 4090751 Email service eid electrolux ie 23 Customer Care Department For general enquiries concerning your Zanussi Electrolux appliance or for further information on Zanussi Electrolux products please contact our Customer Care Department by letter or telephone at the address below or visit our website at www zanussi co uk Customer Care Department Zanussi Electrolux 55 77 High Street Slough Berkshire SL1 1DZ Tel 08705 727727 calls to this number may be recorded for training purposes Guarantee Conditions Standard guarantee conditions We Zanussi Electrolux undertake that if within 12 months of the date of the purchase this ZANUSSI ELECTROLUX appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials we will at our option repair or replace the same FREE OF ANY CHARGE for labour materials or carriage on condition that e The appliance has been correctly installed and used only on the electricity supply stated on the rating plate e The appliance has be
28. iquid in traditional or compact form is your own personal choice TRADITIONAL POWDERS Pour the powder directly into the dispenser drawer Do not sprinkle powder onto clothes in the machine drum TRADITIONAL LIQUIDS Liquid can be placed in the main wash compartment of the detergent drawer marked with the symbol UI start the machine immediately upon placing the detergent in the dispenser drawer Alternatively the detergent is measured into the specially designed dosing device which should be placed on top of the laundry and at the back of the machine drum COMPACT POWDERS AND LIQUIDS Compact detergents or concentrates as they are also known are available in liquid or powder form and generally require a smaller dosage Follow the manufacturer s instructions to ensure the most economical usage Pour the detergent directly into the dispenser drawer or alternatively measure the detergent into the specially designed dosing device which should be placed on top of the laundry and at the back of the machine drum Tf you use a dosing device in a washer dryer please ensure the dosing device ball is removed before carrying out a drying programme FABRIC CONDITIONERS These are ideal for improving softness and also reduce static cling on synthetics and make ironing easier They are available in two types For example Lenor liquid fabric softener for use in the washing machine washer dryer The liquid fabric soft
29. is should be carried out by our Service Force Centre Technical Specifications gt gt gt gt gt DIMENSIONS Height 85 cm Width 60 cm Depth 57 cm POWER SUPPLY VOLTAGE 230 240 V 50 Hz TOTAL POWER ABSORBED 2050 W 10A Minimum 50 kPa WATER PRESSURE Maximum 800 kPa Washing MAX LOAD CAPACITY Cotton linen 5 kg Synthetics 2 5 kg Delicate fabrics 2 5 kg Wool and Hand Wash 2 kg Drying Cotton linen 2 5 kg Synthetics 2 kg SPIN SPEED Maximum 1200 rpm CONSUMPTION DATA FOR WASHING Energy 0 95 kWh 5 KG NORMALLY SOILED COTTON Water 49 litres ITEMS AT 60 C This appliance complies with the following E E C Directives 73 23 EEC of 19 2 73 Low Voltage Directive and subsequent modifications 89 336 EEC of 3 5 89 Electromagnetic Compatibility Directive and subsequent modifications 25 Unpacking All transit bolts and packing must be removed before using the appliance You are advised to keep all the packaging for re use in case the machine is to be transported again Using a spanner unscrew and remove the two rear bottom screws Slide out the two plastic pins Lay the machine gently on its back making sure that the hoses are not squashed Remove the polystyrene block from the bottom of the machine and release the two plastic bags Very carefully slide out the left polythene bag removing Repeat the operation for the right polythene bag removing it towa
30. isfactory washing results Too little detergent or unsuitable detergent has been used An insufficient amount of detergent leaves the laundry looking grey and causes lime scale to form Stubborn stains have not been treated prior to washing The correct wash programme temperature has not been selected Too much laundry has been placed in the drum 22 Possible causes The machine vibrates when spinning The internal packing has not been removed The machine is in contact with the wall or furniture The machine is not level and stable check diagonally The washing load is badly distributed in the drum Maybe there is very little laundry in the drum The water level is above the bottom edge of the door The machine is heating the water or drying the clothes The drum is turning The door can only be opened when the relevant light has gone out Spinning starts late or the machine J e e The electronic unbalance detection device has cut in because the does not spin laundry is not evenly distributed in the drum The laundry is redistributed by reverse rotation of the drum This may happen several times before the unbalance disappears and normal spinning can resume If after few minutes the laundry is still not evenly distributed in the drum the machine will spin at a lower spin or will not spin In this case redistribute the load manually and select the spin programme The machine makes an unusual e The machine is fitted with a type of mo
31. machine empty in order to remove any manufacturing residue from the drum and tub Pour half a measure of detergent into the main wash compartment and start up the machine Load the laundry Open the door Place the laundry in the drum one item at a time shaking them out as much as possible Close the door 2 Measure out the detergent Pull out the dispenser drawer until it stops Measure out the amount of detergent required and pour it into the main wash compartment LIL If you wish to carry out the prewash pour detergent into the appropriate compartment marked LL 3 Measure out the fabric softener If required pour fabric softener into the compartment without exceeding the MAX mark marked Close the drawer gently 11 4 Switch the machine on Press the ON OFF button to switch the machine on The display will show three blinking dashes or a blinking zero The light above the button will light up O ON Ofe 5 Select the desired programme fabric Press the FABRICS button repeatedly in order to select the desired programme fabric The relevant light will light up The lights relevant to the phases that form the programme will light up The display will show the duration of the selected programme calculated on the basis of the maximum load for each type of fabric The START PAUSE button light will start flashing If the load of laundry to be washed is small at the beginning of the
32. no supply at the socket The main fuse or the fuse in the plug has blown The START PAUSE button has not been depressed The DELAY START option has been selected he machine does not fill The water tap is closed E10 The filter in the inlet hose is blocked E10 The inlet hose may be squashed or kinked E10 The door has not been closed E40 The machine fills then empties The end of the drain hose is too low immediately The end of the drain hose is submerged in water There is no vent in the end of the drain hose The machine does not empty and or The drain hose may be squashed or kinked E20 does not spin The RINSE HOLD option has been selected The drain pump may be blocked E20 The drain hose extension if fitted is not correct Follow the instructions for connecting to the waste The drainage system pipes are blocked The wash load is unbalanced redistribute the clothes inside the drum to allow the machine to spin There is water on the floor Too much detergent or unsuitable detergent has been used creates too much foam Check whether there are any leaks from the inlet hose fittings It is not always easy to see this as the water runs down the hose check to see if it is damp The drain hose may be damaged or not securely positioned The detergent dispenser drawer or recess is clogged The drainage system pipes are blocked The cap on the emergency emptying hose has not been replaced after cleaning the pump Unsat
33. nut but the machine MUST be level and stable check diagonally Any necessary adjustment can be made with a spanner Accurate levelling prevents vibration noise and displacement of the machine during operation Some vibration is inevitable especially if mounted on a wooden floor Sprung wooden floors are particularly susceptible to vibration For advice consult a builder If possible always place the machine on a solid floor Special conditions If the floor is carpeted or covered with crumbly or soft material insert a rigid support base under the feet to prevent noise vibration or displacement The base should protrude a few centimetres beyond the edges of the machine 28 Warning A The machine should NOT be placed on deep pile carpeting Note Please ensure that when the appliance is installed it is easily accessible for the engineer in the event of a breakdown In the interest of the environment Washing machines and dishwashers should be connected to the FOUL drainage system the water will then be taken to a sewage works for treatment before being discharged safely into a river It is essential that these appliances are not connected to the surface water drainage system as this water is discharged directly into a river or stream and may cause pollution If you require any further advice please contact your local water authority t i SHOWER SINK TOILET WASHING MACH
34. o this the next time you switch the machine on the blinking zero will appear on the display and you will hear the audible signal Note when you switch the machine on if you must erase the previously performed programme it is also sufficient to press the FABRICS button and select a new programme Press the ON OFF button to switch the machine off The relevant light will go out Remove the laundry from the machine Check whether the drum is completely empty by rotating it with your hand The purpose of this is to prevent any items of laundry from remaining accidentally in the drum where they might get damaged in a subsequent wash e g by shrinking or bleed colour into another load of laundry We advise you to close the water supply tap and disconnect the plug from the socket Leave the door ajar in order to air the machine DRYING 2 5 KG OF COTTON You have for example just machine washed and spun at 1200 rpm 5 kg 11 Ib of laundry They are cotton fabrics of medium weight which you want to iron as soon as they are dry Press the SKIP RESET button repeatedly to erase the programme that has just been carried out will show in the display and switch the machine off by depressing ON OFF button Then remove the laundry from the appliance and divide the items to obtain two loads of approx 2 5 kg 5 5 1b each The water tap must be open and the drain hose must be positioned in the sink or connected to the drain pipe
35. r qualified plumber Installation on a Suspended Floor Suspended wooden floors are particularly susceptible to vibration To help prevent vibration we recommend you place a waterproof wood panel at least 15 mm thick under the appliance secured to at least 2 floor beams with screws If possible install the appliance in one of the corners of the room where the floor is more stable Water inlet Connect the hose supplied with the machine to a tap with a 3 4 thread Do not use already employed hoses Installation should comply with local water authority and building regulations requirements The appliance must be connected to a cold water supply A minimum water pressure of 50 kPa 0 5 bar is required for safe operation of the appliance If you cannot make the cold water connection direct from the rising mains you may be able to operate the appliance from your cold water storage system There should be a minimum distance of 5 02m 161 2 ft between the appliance s inlet and the bottom of the water storage tank Set the hose correctly by loosening the ring nut After positioning the inlet hose be sure to tighten the ring nut again to prevent leaks Water drainage This appliance is designed to be permanently plumbed into your home s water supply and drainage system The appliance drain hose should hook into a standpipe the hook in the drain hose is formed using the plastic U Piece supplied
36. rds the left and then upwards Remove the polystyrene base Set the machine upright and unscrew the remaining rear screw Slide out the relevant pin Fill all the holes with the plastic plugs supplied with the instruction booklet Important You are advised to keep all the packaging for re use in case the machine is to be transported again In case of moving out the same precautions as per paragraphe The dangers of freezing must be taken i e the residual water in the hoses must be pumped out Positioning Install the machine on a flat hard floor Make sure that air circulation around the machine is not impeded by carpets rugs etc Check that the machine does not touch the wall or other kitchen units Never place cardboard wood or similar materials under the machine to compensate for any unevenness in the floor Your new washing machine has been designed to be permanently plumbed in to your home s water supply and drainage system However if this is not possible it may be connected to a suitable existing tap with the drain hose discharging into a sink The appliance has an inlet hose with female 3 4 BSP thread connector If this connection is not compatible with the plumbing of the existing installation a variety of connectors are available from good hardware stores and plumbers merchants to suit most domestic plumbing Any alteration to your existing plumbing must be carried out by a competent person o
37. special child safety feature to prevent small children from being trapped inside the machine To activate this device rotate the button without pressing it inside the door clockwise until the groove is horizontal If necessary use a coin To disable this device and restore the possibility of closing the door rotate the button anti clockwise until the groove is vertical The Control Panel AR Mn SP see ON OFF button Press this button to switch the machine on The display 9 will show three blinking dashes or a blinking zero You will find more detailed explanations on page 7 e 8 see DISPLAY Press the ON OFF button again to switch the machine off 2 MAINS ON light This light is connected to the ON OFF button It lights up when you press the button and goes out when you press it again 3 FABRICS button Press this button repeatedly to select the programme on the basis of the type of laundry to be washed The light relevant to the selected programme will light up The machine will propose a temperature and automatically select the maximum spin value provided for the programme you have chosen You can change these values by operating buttons 4 and 5 Hand wash When you select this programme you obtain a particularly delicate washing suitable for articles of clothing whose label indicates that they must be hand washed 4 TEMPERATURE button Press this button repeatedly to increas
38. st rinse so as not to wrinkle the laundry At the end of the cycle the START PAUSE button light will flash to indicate that the water must be drained and a static zero will appear on the display To complete the cycle choose one of the following options Draining and spin Press the START PAUSE button The machine will drain the water then spin the laundry at the maximum speed provided for the selected programme Select spin speed by means of button 5 and press the START PAUSE button Drain only Press the SKIP RESET button once so as to cause the DRAIN light by to light up then press the START PAUSE button Important If you accidentally press the SKIP RESET button more than once the display will show three blinking dashes To cause the washing machine to drain the water select any washing programme by means of the FABRIC button then press SKIP RESET three times in order to select the DRAIN position only the DRAIN light will remain lit The RINSE HOLD option cannot be selected for the automatic WASHING amp DRYING programme 6 OPTIONS button Press this button to select the following options e PREWASH select this option if you wish your laundry to be prewashed before the main wash not available for wool and hand wash cycle The prewash ends with a short spin at 650 rpm in programmes for cotton and synthetic fabrics whereas in the programme for delicate fabrics the water is only drained SU
39. t Safety Information Your New Washer Dryer Description of the Appliance Door locked light Detergent dispenser drawer Child safety feature The Control Panel Operating sequence Washing Load the laundry Measure out the detergent Measure out the fabric softener Switch the machine on Select the required programme fabric Select the temperature Select the spin speed or the RINSE HOLD option Select the desired options Select the DELAY TIME Start the programme How to change a programme during its cycle How to cancel a programme during its cycle How to open the door during the cycle of a programme End of programme Drying 2 5 kg of cotton Autodrying 2 kg of synthetics Washing and Drying Hints Which detergent to use And in which form Wash Care Symbols Washing Programmes Drying Programmes Maintenance and Cleaning Descaling After each wash Maintenance wash External cleaning Cleaning the dispenser drawer Cleaning the drawer recess Cleaning the pump Cleaning the water inlet filter The dangers of freezing Emergency emptying out Something Not Working Service and Spare Parts Guarantee Conditions For the Installer Installation Instructions Technical Specifications Unpacking Positioning Water inlet Water drainage Levelling Special conditions In the interest of the environment Electrical connection Guide to use the Instruction Book The following symbols will be found in the text to
40. tor which makes an unusual noise noise compared with other traditional motors This new motor ensures a softer start and more even distribution of the laundry in the drum when spinning as well as increased stability of the machine No water is visible in the drum e Machines based on modern technology operate very economically using very little water without affecting performance The machine does not dry or does The drying time or degree of drying has not been selected not dry properly The water tap is not turned on E10 The drain pump is clogged E20 The machine is overloaded The selected drying time or degree of dryness was not suitable for the laundry j Before calling out an engineer please ensure you have SERVICE FORCE 8 gineer p y Service amp Spare Parts read the details under the heading Something Not In the event of your appliance requiring service or if Working you wish to purchase spare parts please contact your When you contact the Service Force Centre you will local Service Force Centre by telephoning need to give the following details 0870 5 929929 1 Your name address and post code 2 Your telephone number Your telephone call will be automatically routed to the 3 Clear and concise details of fault Service Force Centre covering your post code area 4 The model and serial number of the appliance found For the address of your local Service Force Centre and on the rating plate see picture further in
41. uch as socks laces washable belts etc in a washing bag or pillow case as it is possible for such items to slip down between the tub and the inner drum Only use the advised quantities of fabric softener Damage to the fabric can ensue if you over fill Refer to the manufacturer s recommendations of quantities As some duvets and eiderdowns should be washed dried in large commercial machines because of their bulk please check with the manufacturer of the item before washing in a domestic machine The users should always check that they have not left their gas lighters disposable or otherwise in their clothing Never tumble dry items that have had contact with chemicals such as dry cleaning fluid These are of a volatile nature and could cause an explosion Only tumble dry items which have been washed in water or require airing Plastic detergent dispensers should not remain in the drum during the drying cycle as the plastic used is not designed to withstand the heat If you wish to wash through to dry you should use the conventional detergent dispenser drawer Leave the porthole door slightly ajar between washes to preserve the door seal Under no circumstances should you attempt to repair the machine yourself Repairs carried out by inexperienced persons may cause injury or serious malfunctioning Contact your local Service Force Centre Always insist on genuine Zanussi spare parts Contents For the User Importan
42. ured black 29 The wire coloured brown must be connected to the terminal marked L or coloured red Upon completion there must be no cut or stray strands of wire present and the cord clamp must be secure over the outer sheath WARNING A cut off plug inserted into a 13 amp socket is a serious safety shock hazard Ensure that the cut off plug is disposed of safely Should the appliance power supply cable need to be replaced this should be carried out by our Service Force Centre Note When the appliance is installed the power supply cable must be accessible Permanent connection In the case of permanent connection it is necessary that you install a double pole switch between the appliance and the electricity supply mains with a minimum gap of 3mm between the switch contacts and of a type suitable for the required load in compliance with the current electrical regulations The switch must not break the yellow and green earth cable at any point From the Electrolux Group The world s No 1 choice The Electrolux Group is the world s largest producer of powered appliances for kitchen cleaning and outdoor use More than 55 million Electrolux Group products such as refrigerators cookers washing machines vacuum cleaners chain saws and lawn mowers are sold each year to a value of approx USD 14 billion in more than 150 countries around the world Electrolux ple 2003
43. ve compartment should be removed 20 Cleaning the drawer recess Having removed the drawer use a small brush to clean the recess ensuring that all washing powder residue is removed from the upper and lower part of the recess Replace the drawer and run the rinse programme without any clothes in the drum Cleaning the pump The pump should be inspected if the machine does not empty and or spin the machine makes an unusual noise during draining due to objects such as safety pins coins etc blocking the pump Proceed as follows e Disconnect the appliance If necessary wait until the water has cooled down Open the pump door Place a container close to the pump to collect any spillage e Pull out the emergency emptying hose place it in the container and remove its cap When no more water comes out unscrew the pump cover and remove it Always keep a rag nearby to dry up spillage of water when removing the cover Remove any objects from the pump impeller by rotating it Put the cap back on the emergency emptying hose and place the latter back in its seat e Screw the pump cover fully in Close the pump door A Warning When the appliance is in use and depending on the programme selected there can be hot water in the pump Never remove the pump cover during a wash cycle always wait until the appliance has finished the cycle and is empt
44. y 5 mins 9 Display The following pieces of information are shown on the display Three blinking dashes when a programme is cancelled by means of the SKIP RESET button The three blinking dashes will also appear when you press the ON OFF button to switch the machine on if the previously selected cycle has been erased Duration of washing programme in hours Important and minutes after you have selected a programme The first time you use the machine when you switch it on it may display a blinking zero and give an audible warning signal This is due to the fact that the machine has performed a washing cycle during the manufacturer s inspection tests and this cycle has not been erased after its completion Delay start a time value indicated in hours and selected by means of the relevant button g While the programme is running after you have pressed the START PAUSE button the displayed time value decreases by one unit every minute Selected drying time in minutes or hours and minutes g The delay time is displayed for 3 seconds then the duration of the selected programme reappears After you have pressed the START PAUSE button the countdown begins and the delay time value decreases by one unit every hour You can delay the start of the selected programme by up to 24 hours in one hour intervals 6 After the programme has started the time remaining is An incorrect option selection has been mad
45. y When replacing the cover ensure it is securely retightened so as to stop leaks and young children being able to remove it Cleaning the water inlet filter If your water is very hard or contains traces of lime deposit the water inlet filter may become clogged It is therefore a good idea to clean it from time to time Turn off the water tap Unscrew the water inlet hose Clean the filter using a hard bristle brush Tighten up the inlet hose The dangers of freezing If the machine is exposed to temperatures below 0 C certain precautions should be taken e Turn off the water tap e Unscrew the inlet hose e Place the end of the emergency emptying hose and that of the inlet hose in a bowl placed on the floor and let water drain out e Screw the water inlet hose back on and reposition the emergency emptying hose after having put the cap on again e When you intend to start the machine up again make sure that the room temperature is above 0 C Important Every time you drain the water through the emergency emptying hose you must pour 2 litres of water into the main wash compartment of the detergent drawer and then run the drain programme This will activate the ECO valve avoiding that part of the detergent remains unused at next washing Emergency emptying out If the water is not discharged proceed as follows to empty out the machine e pull out the plug from the power socket close the water tap if
Download Pdf Manuals
Related Search