Zanussi CWH 6065/9065X Instruction Booklet
Contents
1. 2 recirculation venting grilles G 3 1 recirculation ducting spigot F 4 1 extraction ducting spigot A D 1 fixing kit consisting of 3 wall brankets 1 2 3 Rawlplugs and screws Clearance Height The cooker hood is designed to be fitted over a cooking appliance at the clearance heights stated providing the maximum output of the appliance beneath does not exceed the maximums quoted in the Technical Specifications If the output of the appliance below the cooker hood exceeds the maximum outputs quoted please refer to the cooker manufacturer s installation instructions A minimum clearance height of 650mm 25 2 is required when installed above a built in electric hob or 700mm 27 2 when installed above a built in gas hob A minimum clearance height of 685mm 27 is required when installed above a slot in electric cooker or 787mm 30 2 when installed above a slot in gas cooker When installed between adjoining wall cabinets the wall cabinets must not overhang the hob and the distance between the underside of the cabinet and the worktop must be 450mm If the height of the wall cabinet is less than 450mm a gap of 50mm must be maintained either side of the hob This cooker hood must not be installed above a cooking appliance with a high level grill i Fitting the Wall Brackets Draw vertical line on the wall from the centre of the cooking appliance up to the ceili2. AIRFLOW MAX NOISE LEVEL SUITABLE FOR INSTALLATION ABOVE Ce HEIGHT CANOPY HEIGHT CHIMNEY UPPER SECTION Voltage 50Hz OVER ELECTRIC HOB OVER GAS HOB SLOT IN GAS COOKER SLOT IN ELECTRIC COOKER 24cm 40cm 36 cm 60 90 cm 49 cm LOWER SECTION 220 240 V 155 W 140W 15W 650m hr 62db 7KW max 10KW max 13 5KW max 12 4KW max Note CE Marking certifies that this appliance complies with the require ments laid down in EEC directive 89 336 Electromagnetic compatibility and subsequent modifications and Low Voltage directive 72 23 E A This appliance must be earthed Electrical Requirements Any permanent electrical installation must comply with the latest I E E Regulations and local Electricity Board regulations For your own safety this should be undertaken by a qualified electrician e g your local Electricity Board or a contractor who is on the roll of the National Inspection Council for Electrical Installation Contracting NICEIC Electrical Connection Before connecting to the mains supply ensure that the mains voltage corresponds to the voltage on the rating plate inside the cooker hood This appliance is fitted with a 3 core mains cable and must be permanently connected to the electricity supply via a double pole switch having 3mm minimum contact gap on each pole A Switched Fuse Connection Unit to BS1363 Part 4 fitted with a 3 Amp fuse is a recommended mains supply co
3. is not required when installed for extraction To remove see maintenance and cleaning section Recirculation The charcoal filter must be fitted for recirculation When the hood is installed in the recirculation mode the air is recirculated into the kitchen through the two venting grilles located on either side of the lower U shaped section To fit the recirculation mode 1 Fitthe recirculation spigot F to the rectangular outlet on top of the canopy and push it down ensuring that the 4 lugs are fitted into the holes 2 Fit the charcoal filter inside the canopy A RE El he E 7 Note Fitting the Telescopic Chimney The chimney stack consists of two 2 U shaped sections and it is adjustable to different heights To fit the upper section S first widen the two sides of the section slightly so that they can be clamped to the wall brackets 2 and 3 and then ensure that they are correctly fastened The upper section is fixed to the wall bracket 2 by its upper corners Secure the upper section to the bracket 2 using two screws provided with the fixing kit The lower section I of the chimney stack can be fixed in a similar way between the wall brackets 1 and 3 and the wall paying attention to fit the lower part of the section into the recess of canopy Then fix the lower section I to the wall bracket 1 using the two remaining self tapping screws The upper S and lower 1 sectio
4. the Ducting To Fit in the Recirculation Mode Fitting the Telescopic Chimney Guide to use the instruction book The following Symbols will be found in the text to guide you through the instruction book A Safety instructions Step by step instructions These warnings are provided in the interests of your safety Ensure that you understand them all before installing or using this appliance Your safety is of paramount importance If you are unsure about any of the meanings of these warnings contact the Customer Care Department Installation Any installation work must be undertaken by a qualified electrician or a competent person This hood must be installed in accordance with the installation instructions and all measurements must be adhered to If the cooker hood is installed for use above a gas appliance then the provision for ventilation must be in accordance with the Gas Safety Codes of Practice BS 6172 BS 5440 and BS 6891 Natural Gas and BS 5482 LP Gas 1994 the Gas Safety Installation amp Use Regulations the Building Regulations issued by the Department of the Environment the Building standards Scotland Consolidated Regulations issued by the Scottish Development Department The fan motor of this cooker hood incorporates a cut out device which will operate if the cooker hood is installed below the minimum height recommended under section Clearance Height or if the motor becomes overheated If the
5. INSTRUCTION BOOKLET ZANUSSI COOKER HOOD CWH 6065 9065X Thank you for buying a Zanussi product To enable you to use your appliance effectively and safely please read this instruction book carefully before using the appliance and retain for future reference If you require guidance in the use of the appliance or require further information on Zanussi Products please contact our Customer Care Department Customer Care Department Zanussi Limited Zanussi House Hambridge Road Newbury Berkshire RG14 5EP Tel 01635 521313 Fax 01635 42970 To register ownership please ensure you complete and return the guarantee card supplied with the appliance For the User Important Safety Information Your Appliance Recirculation Extraction Operating Instructions Cooker Hood Controls To Operate Maintenance and Cleaning External Cleaning Metal Grease Filters Remove the Metal Grease Filters Charcoal Filter To Remove Replace the Charcoal Filter Changing the Fluorescent Tube Something Not Working Service and Spare Parts Peace of Mind for Twenty Four Months Standard Guarantee Conditions For the Installer Installation Instructions Technical Information Electrical Connections Electrical Requirements Electrical Connection Installing the Cooker Hood Installation Requirements Components for Installation Clearance Height Fitting the Wall Brackets Fitting the Canopy Venting Ducting Recirculation To Fit
6. cut out device is activated switch off the fan motor and allow the cooker hood to cool The cut out device will reset itself when the fan motor has cooled significantly It is dangerous to alter the specifications or modify this product in any way When installed between adjoining wall cabinets the wall cabinets must not overhang the hob If the room where the hood is to be used contains a fuel burning appliance such as a central heating boiler then its flue must be of the room sealed or balanced flue type If other types of flue or appliances are fitted ensure that there is an adequate supply of air to the room The ducting system for this appliance must not be connected to any existing ventilation system which is being used for any other purpose Do not install above a cooker with a high level grill Child Safety This appliance is designed to be operated by adults Children should not be allowed to tamper with the controls or play with the appliance During Use This product is for domestic use only Never leave frying pans unattended during use as over heated fats and oils might catch fire Never do flamb cooking under this cooker hood Do not leave naked flames under the hood Maintenance and Service This appliance can be a hazard if the synthetic paper and charcoal filters are not replaced as recommended Under no circumstances should you attempt to repair the appliance yourself Repairs carried ou
7. ng using a spirit level and marking pen This is to ensure the correct vertical alignment of the appliance SEN Fix wall bracket 1 to the wall aligning its marked centre across the vertical line Ensure that the distance between the lowest point of the hood and cooking appliance beneath meet the clearance requirement quoted above 450 mm min A Built in Electric Hob 650mm minimum clearance B Built in Gas hob 700mm minimum clearance C Slot in Electric Cooker 685mm minimum clearance D Slot in Gas Cooker 787mm minimum clearance gt lam I wi Pe x o ys R A c Fresse o E N o D Lo tO rn a a E EEES Clearance Height as specified Note Ensure that the wall bracket is levelled using a spirit level The hood can be aligned or adjusted in height by rotating the adjustment screw 3 Mark on the wall the centres of the two keyholes of the bracket Fix wall bracket 2 to the wall at about 1 2 mm from the ceiling or from the maximum height required paying attention to the correct vertical alignment Mark on the wall the centres of the two keyholes of the bracket Fix wall bracket 3 to the wall paying attention to the correct vertical alignment at a X distance measured as in Fig 2 The X distance being equal to the upper section S it can vary according to the different height of this section needed to suit the ceiling height Mark on the wall the ce
8. nnection accessory to ensure compliance with the Safety Requirements applicable to fixed wiring instructions This appliance conforms to BS 800 1988 and EEC Directive No 78 308 regarding suppression of radio and television interference Please ensure that when the appliance is installed it is easily accessible to an engineer in the event of a breakdown A All installations must comply with the local authorities requirements for the discharge of exhaust air Incorrect installation may affect the safety of this cooker hood Installation Requirements Before installation check the wall to which the cooker hood is to be fitted for electric cables water pipes or gas This cooker hood is designed to be fixed to any rigid vertical surface over a cooking area and can be used in the extraction ducted to the outside or recirculation mode internal recycling The installation work must be undertaken by a qualified and competent person The manufacturer disclaims any responsibility for damages due to incorrect installation of the cooker hood or if the hood is not installed in compliance with relevant regulations controlling this type of installation The CWH 6065 9065 is Supplied with the Following Components for Installation Ws A canopy C including controls worktop illumination and fan unit lt ga 2 A telescopic chimney stack consisting of u U shaped upper section S oO ae U shaped lower section 1
9. ns are fixed to the wall bracket in the middle 3 through a spring and the connection is made by pushing both sections firmly towards the centre Fit the two venting grilles on both sides of the chimney stack paying attention that the mark is positioned on the upper part and the mark gt is positioned toward the front part When the hood is to be used in the recirculation mode ensure that both grilles fit properly to the recirculation spigot Dir 89 336 CEE 73 23 CEE 4323925 01 0998
10. ntre of the two keyholes of the bracket Pilot drill all the holes positions as marked on the wall using 8mm drill Fix the wall brackets 1 2 3 using the 8mm rawlplugs and screws supplied Fitting the Canopy Rotate halfway the two screws R positioned on the hanging lugs of the canopy Hook the canopy on to the wall bracket 1 ensuring that the two lugs of the bracket are fitted on the keyhole fixing points of the canopy and push downwards as allowed by adjustment screws The canopy can be aligned or adjusted in height using the two adjustment screws Carry out the electrical connection as instructed Once the electrical connections have been completed check the worktop illumination motor and motor speeds work properly Venting The hood is more effective when used in the extraction setting ducted to the outside A The ducting used must be manufactured from fire retardant material Ducting The ducting must be fire retardant 125mm Sins in diameter and the length should be no more than 3 metres with one 90 bend 2 metres with two 90 bend Bends of more than 90 will reduce the efficiency of the hood and reduce the airflow 1 Remove the two screws on top of the canopy and secure the spigot fit the spigot A on the rectangular air outlet on the top of the canopy using the two SCrews 2 Connect the ducting to the ducting spigot A using suitable clamps not supplied 3 The charcoal filter
11. ode the charcoal filter absorbs smells and odours The charcoal filter cannot be cleaned we recommend it should be replaced approximately every three months or more often if used for more than three hours per day a 7 To Remove Replace the Charcoal Filter Be First remove the metal grease filters 2 Unscrew the two screws located on each side of the charcoal filter A This appliance can be a fire hazard if the grease and charcoal filters are not replaced as recommended x To Change the Fluorescent Tube 1 Remove the plastic cover T The glass strip is kept in position by retaining lugs Z 2 Move the glass strip foward the control box until the opposite end is free arrow 1 Pull the glass strip slightly down arrow 2 and then move it back toward the opposite direction arrow 3 until the glass strip can be removed 3 The tube can removed by rotating it 90 4 Replace with a new tube of the same type and then refit the plastic cover by following intructions 1 and 2 in reverse ETHING NOT Wi If having followed these instructions carefully your cooker hood fails to work properly please carry out the following checks Symptom Solution The cooker hood will not start The cooker hood is not working effectively The cooker hood has switched off during operation If after all these checks the problem persists contact your local Service Force Centre quoting the model and se
12. oducts of Zanussi manufacture which are not marked by Zanussi Ltd This guarantee is in addition to your statutory and legal rights ZANUSSI EUROPEAN GUARANTEE If you should move to another country within Europe then your guarantee moves with you to your new home subject to the following qualifications The guarantee starts from the date you first purchased your product The guarantee is for the same period and to the same extent for labour and parts as exists in the new country of use for this brand or range of products This guarantee relates to you and cannot be transferred to another user Your new home is within the European Community EC or European Free Trade Area e The product is installed and used in accordance with our instructions and is only used domestically i e anormal household Before you move please contact your nearest Customer Care Centre listed below to give them details of your new home They will then ensure that the local Service Organisation is aware of your move and able to look after you and your appliances France Senlis 33 0 3 44 62 29 99 Germany Nurnberg 49 0 911 323 2600 Italy Pordenone 39 0 1678 47053 Sweden Stockholm 46 0 8 738 79 50 UK Newbury 44 0 1635 521 313 A It is dangerous to alter the specifications or attempt to modify this product in any way Technical Information DIMENSIONS WIDTH CANOPY DEPTH ELECTRICAL SUPPLY POWER CONSUMPTION FAN MOTOR LAMP MAX
13. rial number Please note that it will be necessary to provide proof of purchase for any in guarantee service calls e Check the hood is connected to the electricity supply Check that the fan speed control is set to 1 2 or3 e The fan speed is set high enough for the task e The grease filter is clean e The kitchen is adequately vented to allow the entry of fresh air e If set up for recirculation check that the charcoal filter is still effective e If set up for extraction check that the ducting and outlets are not blocked The safety cut out device has been tripped e Turn off the hob and then wait for the device to reset In guarantee customers should ensure that the above checks have been made as the engineer will make a charge if the fault is not a mechanical or electrical breakdown If you require an engineer or wish to purchase spare parts contact your local Service Force Centre by telephoning 0990 929929 Your telephone call will be routed to your local Service Force Centre For further details please see the accompanying customer care book For general assistance with your appliance or for information on Zanussi products please contact our Customer Care Department Customer Care Department Zanussi Zanussi House Hambridge Road Newbury Berkshire RG14 5EP Tel 01635 521313 IND FOR TWENTY FO STANDARD GUARANTEE CONDITIONS We Zanussi Ltd undertake that if within twen
14. rying pans unattended during use as over heated fats and oils might catch fire Do not leave naked flames under the cooker hood Ensure heating areas on your hob are covered with pots and pans when using the hob and cooker hood simultaneously A Before carrying out any maintenance or cleaning isolate the cooker hood from the mains supply The cooker hood must be kept clean as a build up of grease or fat can be a fire hazard External Cleaning Wipe the cooker hood frequently with warm soapy water using a mild detergent N Never use scouring pads or abrasive cleaners Never use excessive amounts of water when cleaning particularly around the control panel Metal Grease Filter The grease filter absorbs grease and dust during cooking to help keep the appliance clean inside and should be cleaned approximately once every month or more often according to use y Removing the Metal Grease Filters ky J Remove the metal grease filters one at a time 2 Applying slight inward pressure to the metal bar situated in the slot this will release the securing bolts 3 Once the slot with the metal bar is released the metal grease filter can be removed 4 When replacing the filter panels ensure that the securing bolts face downwards The metal grease filters should be washed by hand in mild soapy water or in a dishwasher Allow to dry completely before replacing Charcoal Filter In the recirculation m
15. t by inexperienced persons may cause injury or more serious malfunction Refer to your local Zanussi Service Force Centre Always insist on genuine spare parts YOUR APPLIANCE The cooker hood is designed to extract unpleasant odours from the kitchen it will not extract steam The appliance can be installed to recirculate or extract contaminated air Recirculation The air is cleaned by passing through the filters and then back into the kitchen Extraction The contaminated air enters the hood passing through the grease filter and out through the ducting into the atmosphere Cooker Hood Controls The cooker hood controls are located in a concealed control panel on the right hand side of the canopy beneath the front trim Apply slight pressure to the panel covering the controls and release To close control panel just push it back in To Operate To obtain the best performance it is advisable to switch on the hood a few minutes before you start cooking and leave it running for approximately 15 minutes after finishing Open the control panel and select the required functions A Light ON OFF control 0 Off 1 On B Fan ON OFF control O Off 1 On C Fan Speed control 1 Low 2 Normal 3 Boost When the red pilot light is on the cooker hood is in operation A When used in the ducting mode the charcoal filter is not required Never do flamb cooking under this cooker hood Never leave f
16. ty four months of the date of the purchase this ZANUSSI built in appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials the company will at our option repair or replace the same FREE OF ANY CHARGE for labour materials or carriage on condition that The appliance has been correctly installed and used only on the electrical supply stated on the rating plate e The appliance has been used for normal domestic purposes only and in accordance with the manufacturer s operating and maintenance instructions The appliance has not been serviced maintained repaired taken apart or tampered with by any person not authorised by us All service work under this guarantee must be undertaken by Zanussi Service Force Centre Any appliance or defective part replaced shall become the property of this company Home visits are made between 8 30am and 5 30pm Monday to Friday Visits may be available outside these hours in which case a premium will be charged EXCLUSIONS This Guarantee does not cover Damage or calls resulting from transportation improper use or neglect the replacement of any light bulbs or removable parts of glass or plastic e Costs incurred for calls to put right appliances improperly installed or calls to appliances outside the United Kingdom Appliances found to be in use within a commercial environment plus those which are the subject of rental agreements e Pr
Download Pdf Manuals
Related Search