Yamaha ACD1 Owner's Manual
Contents
1. T 8 2 hi AMP ID 31 Maximum of dente EH ON T ON The total maximum length of Ethernet cable that can be used is 500 meters e Use CATS or higher UTP straight Ethernet cable or STP straight Ethernet cable that connects all eight pins e Both PC N series units and Tn series units can be connected to the same ACD1 e You can make connections to either of the two DATA PORT connectors on the amplifier 7 2 ACD1 Owner s Manual Connection Examples Connections with the KP KM or KH series Up to eight XP XM or KH series units can be connected to the ACDI via the MONITOR REMOTE connectors Connection procedure 1 e Connect the ACD1 s MONITOR REMOTE connector to the MONITOR REMOTE connector of the XP XM or XH series unit using a D Sub 15 pin cable such as a commercially available VGA cable for a com puter monitor as shown below MONITOR REMOTE connector XP series AMP ID 35 MONITO REMOTE x LI LI r H connector Maximum of 8 amps e Use a D sub straight cable that has all fifteen pins connected e The maximum D sub cable length that can be used is 50 meters Connections with controllers from other manufacturers An Ethernet compatible2. YAMAHA AMPLIFIER CONTROL DEVICE ACD1 errr GC lt gt YAMAHA tnt O es YAMAHA ES YAMAHA Owner s Manual Bedienungsanleitung Mode d emploi Manual de instrucciones Manuale di istruzioni PyKOBOACTBO MnoJib30BaTena CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO GUALIFIED SERVICE PERSONNEL The above warning is located on the top of the unit NOT PONA 10 Explanation of Graphical Symbols The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the product IMPORTANT SAFETY INSTRUCTIONS Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with dry cloth Do not block any ventilation openings Install in accordance with the manufacturer s instructions Do not install near any heat sources such as radiators heat registers stoves or ot
3. The LCD is not backlit LCD Backlight is set to Auto OFF To set the unit so that the LCD remains backlit at all times access 5 Utility then LCD Backlight and set it to ON Initializing the internal memory You can initialize the ACD1 s internal memory NOTE e The log data is preserved even if you execute initialization When you initialize the internal memory the content that had been saved in memory scenes for each amp and ACD1 settings will be lost CAUTION Use caution when performing the following steps 1 e Power off the ACD1 2 While holding down the BACK button turn the power on 3 Press the AINC YES button to initialize the internal memory When initialization is completed the ACD1 will automatically restart e During initialization the message Do not turn off will be shown in the display Never power off the amplifier while this message is displayed CAUTION ACD1 Owner s Manual 15 mmm Information for Users on Collection and Disposal of Old Eguipment This symbol on the products packaging and or accompanying documents means that used electrical and electronic products should not be mixed with general household waste For proper treatment recovery and recycling of old products please take them to applicable collection points in accor dance with your national legislation and the Directives 2002 96 EC By disposing of these products corr
4. When mounting multiple ACD1 units in a rack ACD1 ventilation panel amplifier amplifier ventilation panel ACD1 ventilation panel amplifier amplifier Do not mount another ACD1 unit or amplifier above or below the ACD1 CAUTION amplifier amplifier ACD1 ACD1 ACD1 amplifier ACD1 Owner s Manual 9 mmm Preparation Connecting the AC power cable e Be sure to turn all devices OFF before connecting AC mains power CAUTION First plug the female connector end of the included AC cable into the AC IN socket on the rear panel of the ACD1 then plug the male plug into an appropriate AC outlet Be sure to use an AC outlet of the voltage specified for the device Turning the power on and off e To prevent the initial power on surge from generating a large noise spike or damaging your speaker system turn
5. COUNTRIES Yamaha Music Europe GmbH SiemensstraBe 22 34 25462 Rellingen Germany Tel 49 4101 3030 AFRICA Yamaha Corporation Asia Pacific Music Marketing Group Nakazawa cho 10 1 Naka ku Hamamatsu Japan 430 8650 Tel 8 1 53 460 2313 MIDDLE EAST TURKEY CYPRUS Yamaha Music Europe GmbH SiemensstraBe 22 34 25462 Rellingen Germany Tel 04101 3030 OTHER COUNTRIES Yamaha Music Gulf FZE LOB 16 513 P O Box 17328 Jubel Ali Dubai United Arab Emirates Tel 971 4 881 5868 ASIA THE PEOPLE S REPUBLIC OF CHINA Yamaha Music amp Electronics China Co Ltd 2F Yunhedasha 1818 Xinzha lu Jingan qu Shanghai China Tel 021 6247 2211 INDIA Yamaha Music India Pvt Ltd SF Ambience Corporate Tower Ambience Mall Complex Ambience Island NH 8 Gurgaon 122001 Haryana India Tel 0124 466 5551 INDONESIA PT Yamaha Music Indonesia Distributor PT Nusantik Gedung Yamaha Music Center Jalan Jend Gatot Subroto Kav 4 Jakarta 12930 Indonesia Tel 21 520 2577 KOREA Yamaha Music Korea Ltd SF 9F Dongsung Bldg 158 9 Samsung Dong Kangnam Gu Seoul Korea Tel 080 004 0022 MALAYSIA Yamaha Music Malaysia Sdn Bhd Lot 8 Jalan Perbandaran 47301 Kelana Jaya Petaling Jaya Selangor Malaysia Tel 3 78030900 SINGAPORE Yamaha Music Asia Pte Ltd 03 11 A Z Building 140 Paya Lebor Road Singapore 409015 Tel 747 4374 TAIWAN Yamaha KHS Music Co Ltd 3F 6 Sec 2 Nan J
6. Ethernet cable D Sub cable Ethernet straight cable Tn series E XP series Maximum of 8 amps Maximum of 32 amps TXn series Connections between the ACD1 and computer e Use a network switch that is compatible with 100Base TX 10Base T e The network switch is not necessary H the computer and ACD1 are directly connected e The Ethernet cable between the computer or network switch and the ACD1 can be no longer than 100 meters However due to variations in computers network switches and cable quality proper operation at the maximum length cannot be guaranteed in some cases e In the United States or Canada the Ethernet cables that connect the ACD1 to the computer or network switch should be STP cables in order to avoid electromagnetic interference e Since the ACD1 supports Auto MDI MDI X it will automatically detect whether the connected cable is of the straight type or crossover type and will configure itself to create the appropriate connection Therefore you can use either a straight or crossover cable ACD1 Owner s Manual 11 mmm Connection Examples Connections with the PC N or Tn series The ACDI allows daisy chain connection of up to 32 PC N or Tn
7. Umwelt die andernfalls durch unsachgere fe chte M llentsorgung auftreten k nnten Fur weitere Informationen zum Sammeln und Wiederaufbereiten alter Elektroger te kontaktieren Sie bitte Ihre rtliche Stadt oder Gemeindeverwaltung Ihren Abfallentsorgungsdienst oder die Verkaufsstelle der Artikel Information fur geschaftliche Anwender in der Europaischen Union Wenn Sie Elektrogerate ausrangieren m chten kontaktieren Sie bitte Ihren Handler oder Zulieferer f r weitere Infor mationen Entsorgungsinformation fur Lander auBerhalb der Europ ischen Union Dieses Symbol gilt nur innerhalb der Europ ischen Union Wenn Sie solche Artikel ausrangieren m chten kontak tieren Sie bitte Ihre rtlichen Beh rden oder Ihren Handler und fragen Sie nach der sachgerechten Entsorgungsmeth ode rn Information concernant la Collecte et le Traitement des d chets d quipements lectriques et lectroniques Le symbole sur les produits emballage et ou les documents joints signifie que les produits lectriques ou lectron iques usag s ne doivent pas tre m lang s avec les d chets domestiques habituels Pour un traitement une r cup ration et un recyclage appropri s des d chets d quipements lectriques et lectron iques veuillez les d poser aux points de collecte pr vus a cet effet conform ment a la r glementation nationale et aux Directives 2002 96 EC En vous d barrassant correctement des d chets d quipements lec
8. Yamaha service personnel anne f i Data items maintained in the internal memory by the backup battery are as Do not rest your weight on the device or place heavy objects on it and follows avoid use excessive force on the buttons switches or connectors e Current scene parameters and number e Device parameters Device Setup Utility Network Setup etc Yamaha cannot be held responsible for damage caused by improper use or modifications to the device or data that is lost or destroyed Always turn the power off when the device is not in use The performance of components with moving contacts such as switches volume controls and connectors deteriorates over time Consult qualified Yamaha service personnel about replacing defective components European models Purchaser User Information specified in EN55103 1 and EN55103 2 Inrush Current 45A Conforms to Environments E1 E2 E3 and E4 O SPECIAL NOTICES The illustrations and LCD screens as shown in this manual are for instructional purposes only and may appear somewhat different from those on your instrument e Windows is a registered trademark of Microsoft Corporation in the United States and other countries e The company names and product names in this manual are the trademarks or registered trademarks of their respective companies For customers using the PC9500N PC4800N or PC3300N power amplifiers If your system con
9. address will be set automatically from Amp Editor DHCP or set manually Manual IP Address Specifies the ACD1 s IP address MAC Address Displays the ACD1 s MAC address IP Ctrl Port Specifies the port number used when controlling the ACD1 via Ethernet from an external controller such as AMX Crestron 14 ACD1 Owner s Manual Troubleshooting Symptom Possible causes Response All scene data saved in the ACD1 has disappeared The power was turned off while the ACD1 s data was being saved Synchronize with Amp Editor once again to transmit the set tings from Amp Editor The backup battery has run down Check 5 Utility gt Battery for the state of the backup bat tery If the state shows any message other than OK ask qualified Yamaha service personnel to replace the backup battery An alert message is displayed An incorrect or abnormal connec tion with the amplifier or other alert event related to the connections has occurred For details on the meaning of each alert message and the appropriate measures to take refer to the Amp Editor Owner s Manual Panel operations are not accepted The unit is locked For details refer to 5 Utility in the ACD1 reference manual A scene can be saved but not recalled Scene Recall is set to Disable Access 5 Utility then SceneRecall and set it to Enable
10. controller such as AMX or Crestron can be connected allowing remote control of the ACD1 and the amplifiers connected to the ACD 1 If you connect an Ethernet compatible remote controller you must set the ACD1 IP Port number by using 6 Network Setup gt IP Ctrl Port on the ACDI unit Alternatively in Amp Editor you can click the Device Setup menu command IP Control Port No and open the IP Control Port No dialog box and then specify the ACD1 s IP port number in the External Device Port field For details of the remote control communication protocol please refer to the TXn ACDI remote control protocol specification provided on the website http www yamahaproaudio com ACDI Owner s Manual 13 mmm Operations that can be performed from the panel The following operations can be performed from the ACD1 s front panel YAMAHA A INC YES BACK NEXT v DEC NO e For details refer to the ACD1 Reference Manual e Before use remove the transparent protective film that was applied to the LCD prior to shipment from the factory Category Sub category Operation performed 1 Scene Recall Recalls a scene on the specified amplifier Store Saves a scene for the specified amplifier 2 Amp Control Standby On Switches the power of the specified amplifier between On and Standby Mute Mutes or unmutes the channel of the specified amplifier Attenuation Adjusts
11. for future reference A WARNING Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock short circuiting damages fire or other hazards These precautions include but are not limited to the following Power supply Power cord e Only use the voltage specified as correct for the device The required e Do not expose the device to rain use it near water or in damp or wet voltage is printed on the name plate of the device conditions or place containers on it containing liquids which might spill e Use only the included power cord If you intend to use the device in an area into any openings If any liquid such as water seeps into the device turn off other than in the one you purchased the included power cord may not be the power immediately and unplug the power cord from the AC outlet Then compatible Please check with your Yamaha dealer have the device inspected by qualified Yamaha service personnel e Do not place the power cord near heat sources such as heaters or radiators e Never insert or remove an electric plug with wet hands and do not excessively bend or otherwise damage the cord place heavy objects on it or place it in a position where anyone could walk on trip over If you notice any abnormality or roll anything over it i e lfthe power cord or plug becomes frayed or damaged or if there is a Be sure to connect to an appropriate outlet wit
12. series units using Ethernet cable via the DATA PORT con nector Connection procedure 1 e Make the appropriate AMP ID and terminator settings using the JAMP ID switches located on the rear panel of the connected amplifiers Specify a different AMP ID for each amplifier that is connected to the same ACD1 The AMP ID will be the total of the values of the switches that are set to ON Set the T terminator switch to ON for the last amplifier in the daisy chain Le 4 1 H H H P B In the example shown in this illustration the AMP ID is 28 16 8 4 and the terminator is ON ON AMP ID 2 Use Ethernet cables to daisy chain the ACD1 s DATA PORT connector and the DATA PORT connector of the amplifiers as shown in the illustration It is not necessary to connect the amplifiers in order of their AMP ID but connecting them in this order will make it easier to determine the AMP ID without looking at the rear panel ACD1 ng DATA PORT connector T 2 1684 1 AMP ID 0 So ARANA o ot PHH En kill T OFF aie 82 DATA PORT ON ioe T 8 2 161411 AMP ID 1 So AAA rawa e rsa PHI BAHAN OFF WM Se a H DATA PORT ON oo LULUH T 8 2 1614 11 AMP ID 2 sasen T OFF ON DATA PORT
13. Manual UL60065_03 FCC INFORMATION U S A 1 IMPORTANT NOTICE DO NOT MODIFY THIS UNIT This product when installed as indicated in the instructions contained in this manual meets FCC requirements Modifi cations not expressly approved by Yamaha may void your authority granted by the FCC to use the product 2 IMPORTANT When connecting this product to accesso ries and or another product use only high quality shielded cables Cable s supplied with this product MUST be used Follow all installation instructions Failure to follow instruc tions could void your FCC authorization to use this product in the USA 3 NOTE This product has been tested and found to comply with the requirements listed in FCC Regulations Part 15 for Class B digital devices Compliance with these require ments provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices This equipment generates uses radio frequencies and if not installed and used according to the instructions found in the users manual may cause interference harmful to the opera tion of other electronic devices Compliance with FCC regu lations does not guarantee that interference will not occur in all installations If this product is found to be the source of interference which can be determined by turning the unit OFF and ON
14. a a ian 7 TEMS iii oi 8 Supported IMPI Sacris rias o pai a Ba a wawa 8 Regarding firmware updates 8 Precautions when rack mounting the um 9 PLOMO Dl ila 10 Connection Examples ai 11 Connections with the PCNorfnseres umimi niwimaazim wwe 12 Connections with the XP XM or XH series anana anana anane nenen nenen nana nana eenene 13 Connections with controllers from other manufacturers ii 13 Operations that can be performed from the panel 14 Algo lo EE plo 2 4 12 E 15 Initializing the internal Memory e 15 EE 6 ACDI Owner s Manual Introduction Thank you for purchasing the Yamaha ACDI Amplifier Control Device In order to take full advantage of the ACDI s functionality and to ensure trouble free operation please read this owner s manual carefully before use After you have read the manual keep it in a safe place for reference when needed Related manuals and software This document explains mainly the initial connection Manuals that contain detailed explanations of the ACD1 and Amp Editor as well as the Amp Editor software itself can be downloaded from the following page of the web site http www yamahaproaudio com downloads O List of related manuals ACDI Reference Manual Provides a detailed explanation of the ACD1 s panel operations etc Amp Editor Installation Guide Explains the installation procedure for Amp Editor a
15. bH Branch Austria Schleiergasse 20 A 1100 Wien Austria Tel 01 602039025 PA24 Die Einzelheiten zu Produkten sind bei Ihrer unten aufgef hrten Niederlassung und bei Yamaha Vertragsh ndlern in den jeweiligen Bestimmungsl ndern erh ltlich Para detalles sobre productos contacte su tienda Yamaha m s cercana o el distribuidor autorizado que se lista debajo POLAND Yamaha Music Europe GmbH Branch Sp z 0 0 Oddzial w Polsce ul 17 Stycznia 56 PL 02 146 Warszawa Poland Tel 022 868 07 57 THE NETHERLANDS BELGIUM LUXEMBOURG Yamaha Music Europe Branch Benelux Clarissenhof 5 b 4133 AB Vianen The Netherlands Tel 0347 358 040 FRANCE Yamaha Musique France BP 70 77312 Marne la Vall e Cedex 2 France Tel 01 64 61 4000 ITALY Yamaha Musica Italia S P A Combo Division Viale Italia 88 20020 Lainate Milano Italy Tel 02 935 771 SPAIN PORTUGAL Yamaha M sica Ib rica S A Ctra de la Coruna km 17 200 28230 Las Rozas Madrid Spain Tel 91 639 8888 SWEDEN Yamaha Scandinavia AB J A Wettergrens Gata 1 Box 30053 S 400 43 G teborg Sweden Tel 031 89 34 00 DENMARK YS Copenhagen Liaison Office Generatorvej 6A DK 2730 Herlev Denmark Tel 44 92 49 00 NORWAY Norsk filial av Yamaha Scandinavia AB Grini N ringspark 1 N 1345 ster s Norway Tel 67 16 77 70 RUSSIA Yamaha Music Russia Office 4015 entrance 2 21 5 Kuznetskii Most street Moscow 107996 Russia Tel 495 626 0660 OTHER EUROPEAN
16. eceived including interference that may cause undesired operation See user manual instructions if interference to radio reception is suspected This applies only to products distributed by FCC DoC YAMAHA CORPORATION OF AMERICA IMPORTANT NOTICE FOR THE UNITED KINGDOM Connecting the Plug and Cord WARNING THIS APPARATUS MUST BE EARTHED IMPORTANT The wires in this mains lead are coloured in accordance with the following code GREEN AND YELLOW EARTH BLUE NEUTRAL BROWN LIVE As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows The wire which is coloured GREEN and YELLOW must be connected to the terminal in the plug which is marked by the letter E or by the safety earth symbol or colored GREEN or GREEN and YELLOW The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED This product contains a battery that contains perchlorate material Perchlorate Material special handling may apply See www dtsc ca gov hazardouswaste perchlorate This applies only to products distributed by Perchlorate YAMAHA CORPORATION OF AMERICA ADVARSEL Lithiumbatteri Eksplosionsfare ved fejlagtig h ndtering Udskif
17. ectly you will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling For more information about collection and recycling of old products please contact your local municipality your waste disposal service or the point of sale where you purchased the items For business users in the European Union If you wish to discard electrical and electronic equipment please contact your dealer or supplier for further information Information on Disposal in other Countries outside the European Union This symbol is only valid in the European Union If you wish to discard these items please contact your local authori ties or dealer and ask for the correct method of disposal Verbraucherinformation zur Sammlung und Entsorgung alter Elektrogerate Befindet sich dieses Symbol auf den Produkten der Verpackung und oder beiliegenden Unterlagen so sollten benutzte elektrische Ger te nicht mit dem normalen Haushaltsabfall entsorgt werden In Ubereinstimmung mit Ihren nationalen Bestimmungen und den Richtlinien 2002 96 EC bringen Sie alte Ger te bitte zur fachgerechten Entsorgung Wiederaufbereitung und Wiederverwendung zu den entsprechenden Sammelstellen Durch die fachgerechte Entsorgung der Elektroger te helfen Sie wertvolle Ressourcen zu sch tzen und verhindern m gliche negative Auswirkungen auf die menschliche Gesundheit und die
18. formance To ensure that the heat produced by this device can be dissipated appropriately please ensure the following conditions when rack mounting it When mounting this device together with other heat producing equipment such as power amplifiers leave 1U or more space between it and other devices including other ACDI units Install a ventilation panel in this vacant space or leave it open to ensure adequate cooling e Leave the back of the rack open and allow at least 10 cm of space between the rack and the wall and ceiling to ensure ade quate cooling If you ve installed a fan kit there may be cases in which closing the back of the rack will produce a greater cooling effect For details refer to the owner s manual of your rack or fan kit E When mounting the ACD1 together with compatible amplifiers 1 When mounting only one ACDI in a rack ACD1 ventilation panel amplifier amplifier amplifier amplifier amplifier amplifier YAMAHA 2
19. h a protective grounding sudden loss of sound during use of the device or if any unusual smells or connection Improper grounding can result in electrical shock smoke should appear to be caused by it immediately turn off the power switch disconnect the electric plug from the outlet and have the device Do not open inspected by qualified Yamaha service personnel e Do not open the device or attempt to disassemble the internal parts or e If this device should be dropped or damaged immediately turn off the modify them in any way The device contains no user serviceable parts If it power switch disconnect the electric plug from the outlet and have the should appear to be malfunctioning discontinue use immediately and have device inspected by qualified Yamaha service personnel it inspected by qualified Yamaha service personnel N CAUTION Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others or damage to the device or other property These precautions include but are not limited to the following Power supply Power cord e f several of the devices are mounted in an ElA compliant rack carefully e Remove the electric plug from the outlet when the device is not to be used read the section Precautions when rack mounting the unit on page 9 for extended periods of time or during electrical storms e Do not expose the device to excessive dust or vibrations or extreme c
20. her apparatus including amplifiers that produce heat Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus Only use attachments accessories specified by the manufacturer Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus e When acartis used use caution when moving the cart apparatus combination to avoid injury from tip over Unplug this apparatus during lightning storms or when unused for long periods of time Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped LA 4 WARNING MOISTURE TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS APPARATUS TO RAIN OR Rm 2 ACDI Owner s
21. ing E Rd Taipei Taiwan 104 R O C Tel 02 2511 8688 THAILAND Siam Music Yamaha Co Ltd 4 6 15 and 162 floor Siam Motors Building 891 1 Rama 1 Road Wangmai Pathumwan Bangkok 10330 Thailand Tel 02 215 2626 OTHER ASIAN COUNTRIES Yamaha Corporation Asia Pacific Music Marketing Group Nakazawa cho 10 1 Naka ku Hamamatsu Japan 430 8650 Tel 81 53 460 2317 OCEANIA AUSTRALIA Yamaha Music Australia Pty Ltd Level 1 99 Queensbridge Street Southbank Victoria 3006 Australia Tel 3 9693 5111 COUNTRIES AND TRUST TERRITORIES IN PACIFIC OCEAN Yamaha Corporation Asia Pacific Music Marketing Group Nakazawa cho 10 1 Naka ku Hamamatsu Japan 430 8650 Tel 81 53 460 2313 HEAD OFFICE Yamaha Corporation Pro Audio 4 Digital Musical Instrument Division Nakazawa cho 10 1 Naka ku Hamamatsu Japan 430 8650 Tel 81 53 460 2441 YAMAHA Yamaha Pro Audio global web site http www yamahaproaudio com Yamaha Manual Library http www yamaha co jp manual U R G Pro Audio amp Digital Musical Instrument Division Yamaha Corporation 2009 Yamaha Corporation WM15360 909POCP 02B0 Printed in Japan
22. lifiers E Scene link Settings for simultaneously recalling scenes for multiple amplifiers within an area are called a scene link By recalling a scene link scenes can be simultaneously recalled for multiple amplifiers Scene links can be created and recalled using Amp Editor Supported amplifiers As of September 2009 the following amplifiers support connection with the ACDI e XP series XP7000 XP5000 XP3500 XP2500 XP1000 e XM series XM4180 XM4080 e XH series XH200 e PC N series PC9501N PC6501N PC4801N PC3301N PC2001N PC9500N PC4800N PC3300N e Tn series Tbn T4n T3n For the most recent information refer to the following website http www yamahaproaudio com Regarding firmware updates The firmware version of the ACDI itself can be checked from the ACD1 s panel and from Amp Editor You can update the firmware via Amp Editor For the update procedure refer to the Amp Editor owner s manual You can download the latest firmware from the download page of the following Yamaha website http www yamahaproaudio com downloads Rm 8 ACDI Owner s Manual Precautions when rack mounting the unit This unit will operate stably in an environmental temperature of 0 40 C If you install this device together with multiple units of the same device or other devices in a EIA standard rack the heat produced by the various devices may raise the ambient temperature inside the rack resulting in inefficient per
23. nd the uninstallation procedure Amp Editor Owner s Manual Explains how to set up Amp Editor and the ACDI and how to use Amp Editor e In order to view the downloaded manuals Adobe Reader must be installed in your computer If you don t have Adobe Reader please access the Adobe Corporation s website at the following URL and download Adobe Reader free of charge http www adobe com Features of the ACD1 The ACDI is an amplifier control device with the following features E Monitor and control amplifiers from Amp Editor The ACDI and amplifiers connected to the ACDI can be monitored and controlled from a LAN connected computer in which the Amp Editor application software is installed The ACD1 can also monitor the output signal of the connected amplifiers and control their power supply On Standby status E Monitor and control up to 40 amplifiers A single ACDI unit is able to monitor and control up to 40 connected amplifiers a maximum of eight XP XM XH series units and a maximum of 32 PC N Tn series units can be connected By connecting multiple ACDI units in a single network a larger number of amplifiers can be monitored and controlled via Amp Editor ACD1 Owner s Manual Terms This section explains terminology specific to the ACD1 E Scene Settings such as power on standby or mute for each amplifier are called a scene By recalling a scene the saved settings can be immediately applied to the amp
24. nects the PC9500N PC4800N or PC3300N power amplifiers to the ACD1 there may be cases in which Amp Editor will not display the meters correctly for some power amplifiers Please check whether this problem has been corrected for the power amplifier you re using If not please contact your Yamaha dealer Checking for the correction If the two alphabetical characters at the beginning of the serial number label on the back of the power amp are IL IM IN IO IP IX IY IZ or JH and no green circular label is affixed immediately nearby it then the product has not been corrected For customers using the T5n T4n or T3n power amplifiers When monitoring or controlling the T5n T4n or T3n power amplifiers set the GAIN switch of the T5n T4n or T3n to 26 dB to avoid clipping if you plan to input signals with a maximum input level of 24 dBu When the power amplifier is connected to the ACD1 the electronic volume control inside the amplifier will become effective and the maximum input level will become 18 dBu if the GAIN switch has been set to 32 dB Included Accessories e AC power cord e Euroblock connector 16P e Rubber feet x 4 e Owner s Manual this document 5 6 2 2 ACD1 Owner s Manual 5 mmm Contents o ON anae A E aaa na edaja ae aaa aaa agan dak aaa awa ajaa aenak a aaa aan aaa da aaa aaa aa 7 Related manuals and software i 7 Features of the ACD mic aa aaa a agak aba p
25. ntario MIS 3R1 Canada Tel 416 298 1311 U S A Yamaha Corporation of America 6600 Orangethorpe Ave Buena Park Calif 90620 U S A Tel 714 522 9011 CENTRAL amp SOUTH AMERICA MEXICO Yamaha de M xico S A de C V Calz Javier Rojo G mez 1149 Col Guadalupe del Moral C P 09300 M xico D F M xico Tel 55 5804 0600 BRAZIL Yamaha Musical do Brasil Ltda Rua Joaquim Floriano 913 4 andar Itaim Bibi CEP 04534 013 Sao Paulo SP BRAZIL Tel 011 3704 1377 ARGENTINA Yamaha Music Latin America S A Sucursal de Argentina Olga Cossettini 1553 Piso 4 Norte Madero Este C1107CEK Buenos Aires Argentina Tel 011 4119 7000 PANAMA AND OTHER LATIN AMERICAN COUNTRIES CARIBBEAN COUNTRIES Yamaha Music Latin America S A Torre Banco General Piso 7 Urbanizaci n Marbella Calle 47 y Aquilino de la Guardia Ciudad de Panam Panam Tel 507 269 5311 EUROPE THE UNITED KINGDOM Yamaha Music U K Ltd Sherbourne Drive Tilbrook Milton Keynes MK7 8BL England Tel 01908 366700 GERMANY Yamaha Music Europe GmbH SiemensstraBe 22 34 25462 Rellingen Germany Tel 04101 3030 SWITZERLAND LIECHTENSTEIN Yamaha Music Europe GmbH Branch Switzerland in Ziirich Seefeldstrasse 94 8008 Ziirich Switzerland Tel 01 383 3990 AUSTRIA Yamaha Music Europe GmbH Branch Austria Schleiergasse 20 A 1100 Wien Austria Tel 01 60203900 CZECH REPUBLIC SLOVA KIA HUNGARY SLOVENIA Yamaha Music Europe Gm
26. oductos viejos por favor ll velos a puntos de recolec ci n aplicables de acuerdo a su legislaci n nacional y las directivas 2002 96 EC Al disponer de estos productos correctamente ayudar a ahorrar recursos valiosos y a prevenir cualquier potencial efecto negativo sobre la salud humana y el medio ambiente el cual podr a surgir de un inapropiado manejo de los desechos Para mayor informaci n sobre recolecci n y reciclado de productos viejos por favor contacte a su municipio local su servicio de gesti n de residuos o el punto de venta en el cual usted adquiri los art culos Para usuarios de negocios en la Uni n Europea Si usted desea deshacerse de equipamiento el ctrico y electr nico por favor contacte a su vendedor o proveedor para mayor informaci n Informaci n sobre la Disposici n en otros pa ses fuera de la Uni n Europea Este s mbolo s lo es v lidos en la Uni n Europea Si desea deshacerse de estos art culos por favor contacte a sus autoridades locales y pregunte por el m todo correcto de disposici n Informazioni per gli utenti sulla raccolta e lo smaltimento di vecchia attrezzatura Questo simbolo sui prodotti sull imballaggio e o sui documenti che li accompagnano significa che i prodotti elettriche e elettroniche non dovrebbero essere mischiati con i rifiuti domestici generici Per il trattamento recupero e riciclaggio appropriati di vecchi prodotti li porti prego ai punti di raccolta appr
27. old e When removing the electric plug from the device or an outlet always hold or heat such as in direct sunlight near a heater or in a car during the day the plug itself and not the cord Pulling by the cord can damage it to prevent the possibility of panel disfiguration or damage to the internal components e Do not place the device in an unstable position where it might accidentally fall over e Before moving the device remove all connected cables e Do not use the device in the vicinity of a TV radio stereo equipment e When setting up the device make sure that the AC outlet you are using is mobile phone or other electric devices Doing so may result in noise both easily accessible If some trouble or malfunction occurs immediately turn in the device itself and in the TV or radio next to it off the power switch and disconnect the plug from the outlet Even when the power switch is turned off electricity is still flowing to the product at the minimum level When you are not using the product for a long time make sure to unplug the power cord from the wall AC outlet 5 6 1 2 4 ACD1 Owner s Manual Handling caution e Condensation can occur in the device due to rapid drastic changes in ambient temperature when the device is moved from one location to another or air conditioning is turned on or off for example Using the device while condensation is present can cause damage If there is reason to belie
28. opriati in accordo con la Sua legislazione nazionale e le direttive 2002 96 CE Smaltendo correttamente questi prodotti Lei aiuter a salvare risorse preziose e a prevenire alcuni potenziali effetti negativi sulla salute umana e l ambiente che altrimenti potrebbero sorgere dal trattamento improprio dei rifiuti Per ulteriori informazioni sulla raccolta e il riciclaggio di vecchi prodotti prego contatti la Sua amministrazione comu nale locale il Suo servizio di smaltimento dei rifiuti o il punto vendita dove Lei ha acquistato gli articoli Per utenti imprenditori dell Unione europea Se Lei desidera disfarsi di attrezzatura elettrica ed elettronica prego contatti il Suo rivenditore o fornitore per ulteriori informazioni Informazioni sullo smaltimento negli altri Paesi al di fuori dell Unione europea Questo simbolo validi solamente nell Unione europea Se Lei desidera disfarsi di questi articoli prego contatti le Sue autorit locali o il rivenditore e richieda la corretta modalit di smaltimento ACD1 Owner s Manual ra WE ACDI Owner s Manual For details of products please contact your nearest Yamaha representative or the authorized distributor listed below Pour plus de d tails sur les produits veuillez vous adresser Yamaha ou au distributeur le plus proche de vous figurant dans la liste suivante NORTH AMERICA CANADA Yamaha Canada Music Ltd 135 Milner Avenue Scarborough O
29. please try to eliminate the problem by using one of the following measures Relocate either this product or the device that is being affected by the interference Utilize power outlets that are on different branch circuit breaker or fuse circuits or install AC line filter s In the case of radio or TV interference relocate reorient the antenna If the antenna lead in is 300 ohm ribbon lead change the lead in to co axial type cable If these corrective measures do not produce satisfactory results please contact the local retailer authorized to distrib ute this type of product If you can not locate the appropriate retailer please contact Yamaha Corporation of America Electronic Service Division 6600 Orangethorpe Ave Buena Park CA90620 The above statements apply ONLY to those products distrib uted by Yamaha Corporation of America or its subsidiaries This applies only to products distributed by YAMAHA CORPORATION OF AMERICA class B COMPLIANCE INFORMATION STATEMENT DECLARATION OF CONFORMITY PROCEDURE Responsible Party Yamaha Corporation of America Address 6600 Orangethorpe Ave Buena Park Calif 90620 Telephone 714 522 9011 Type of Equipment Amplifier Control Device Model Name ACD1 This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference r
30. the devices on in the following order audio sources mixer such as M7CL or PM5D ACD1 and finally power amplifi CAUTION ers Reverse this order when turning power off e If you power on the amplifier before the ACD1 the amplifier may be ready before the mute or level setting of the ACD1 becomes effective resulting in an unexpected loud sound e If you power off the ACD1 before your XP XM XH series amplifiers the amplifier s settings will return to their default state 1 e Press the POWER switch to power on the ACD1 2 Press the POWER switch again to turn off the power Noya e The settings at the time you powered off are remembered When you turn on the power again the unit will start up with the same settings You can use the Last Mem Resume setting to set up the unit so that at startup it will recall the scene number selected before you turned off the power to the device Do not power off the unit while its LCD indicates Do not turn off Otherwise a malfunction may occur CAUTION e A small amount of current is flowing even when the power switch is off If you will not be using this device for an extended period of time be sure to disconnect the power plug from the AC outlet CAUTION TO ACD1 Owner s Manual Connection Ekamples To construct an amplifier control system connect the ACDI to your amplifiers and computer as follows Amp Editor
31. the channel attenuator value of the specified amplifier PC N and Tn series only 3 Output Monitor Displays the output level of the specified amplifier 4 Device Setup Device ID Specifies the ACD1 s Device ID address Device Label Displays the name of the ACD1 assigned by Amp Editor Identify Blinks the Identify icon of the corresponding ACD1 in Amp Editor 5 Utility Battery Displays the state of the ACD1 s internal backup battery Firmware Ver Displays the ACD1 s firmware version LCD Backlight Selects whether the ACD1 s LCD backlight will be always lit ON or lit only during operation Auto OFF Panel Operation Restricts panel operations of the ACD1 Scene Recall Specifies whether scene recall from the ACD1 s panel is enabled Enable or dis abled Disable EMG Scene Setup Specifies the scene number that will be recalled when the EMG Emergency sig nal is received from an external controller Last Mem Resume Specifies whether the ACD1 will start up with the settings that were in effect when the power was last turned off ON or whether it will start up by recalling the amp s scene number that was in effect when the power was last turned off OFF Clock Setup Sets the date and time of the ACD1 s internal clock GPI Calibration Calibrates the GPI IN connector input voltage 6 Network Setup IP Address Mode Selects whether the ACD1 s IP
32. tning m kun ske med batteri af samme fabrikat og type Lev r det brugte batteri tilbage til leverandoren VARNING Explosionsfara vid felaktigt batteribyte Anv nd samma batteri typ eller en ekvivalent typ som rekommenderas av apparat tillverkaren Kassera anv nt batteri enligt fabrikantens instruktion VAROITUS Paristo voi r j ht jos se on virheellisesti asennettu Vaihda paristo ainoastaan laitevalmistajan suosittelemaan tyyppiin H vit k ytetty paristo valmistajan ohjeiden mukaisesti lithium caution NEDERLAND THE NETHERLANDS e Dit apparaat bevat een lithium batterij voor geheugen back up e This apparatus contains a lithium battery for memory back up e Raadpleeg uw leverancier over de verwijdering van de bat terij op het moment dat u het apparaat ann het einde van de levensduur of gelieve dan contact op te nemen met de verte genwoordiging van Yamaha in uw land e For the removal of the battery at the moment of the disposal at the end of life please consult your retailer or Yamaha repre sentative office in your country e Gooi de batterij niet weg maar lever hem in als KCA e Do not throw away the battery Instead hand it in as small chemical waste This applies only to products distributed by 3 wires Yamaha Music U K Ltd lithium disposal ACD1 Owner s Manual 3 PRECAUTIONS PLEASE READ CAREFULLY BEFORE PROCEEDING Please keep this manual in a safe place
33. triques et lectroniques vous contribuerez la ki sauvegarde de pr cieuses ressources eta la pr vention de potentiels effets n gatifs sur la sant humaine qui pour raient advenir lors d un traitement inappropri des d chets Pour plus d informations a propos de la collecte et du recyclage des d chets d quipements lectriques et lectron iques veuillez contacter votre municipalit votre service de traitement des d chets ou le point de vente o vous avez achet les produits Pour les professionnels dans l Union Europ enne Si vous souhaitez vous d barrasser des d chets d quipements lectriques et lectroniques veuillez contacter votre vendeur ou fournisseur pour plus d informations Information sur le traitement dans d autres pays en dehors de l Union Europ enne Ce symbole est seulement valables dans Union Europ enne Si vous souhaitez vous d barrasser de d chets d quipements lectriques et lectroniques veuillez contacter les autorit s locales ou votre fournisseur et demander la m thode de traitement appropri e WE ACD1 Owner s Manual Informaci n para Usuarios sobre Recolecci n y Disposici n de Equipamiento Viejo Este s mbolo en los productos embalaje y o documentaci n que se acompa e significa que los productos electr ni cos y el ctricos usados no deben ser mezclados con desechos hogare os corrientes Para el tratamiento recuperaci n y reciclado apropiado de los pr
34. ve that condensation might have occurred leave the device for Backup battery This device has a built in backup battery that maintains data in internal memory even when the device s power is switched off The backup battery will eventually become depleted however and when that happens the contents of he internal memory will be lost To prevent loss of data be sure to replace the backup battery before it becomes fully depleted When the remaining capacity several hours without turning on the power until the condensation has of the backup battery becomes so low that it needs to be replaced a Low completely dried out Battery Critical Battery or No Battery message will appear on the display Do not insert your fingers or hands in any gaps or openings on the device during operation or when the device is powered on If either of these ports etc messages appears do not turn off the power and immediately transfer any data Avoid insert dolia sia obiect lasti tal etc int you want to save to a computer or other external storage device then have vor Insa rung or jaka du 0 Di LI i le P e er qualified Yamaha service personnel replace the backup battery The average a OPERE MINIS AL ee ports etc If this happens turn off the life of the internal backup battery is approximately 5 years depending on power immediately and unplug the power cord from the AC outlet Then operating conditions have the device inspected by qualified
Download Pdf Manuals
Related Search