Xpelair SL100T User's Manual
Contents
1. as Se a m C7 y SL100 SL100T SL150 SLISOHT Slimline Axial Fan Range Installation and maintenance instructions SL100P SLIO0HT SL150P 9 Xpelair SLIMLINE Series LIA IPX4 INSTALLATION Begin the installation by making a circular opening of 100 mm SL100 150 mm SL150 diameter in the ceiling or wall where the extractor is to be installed Remove the front cover A by removing screw SL150 only and pressing the catch 1 with the tip of a screwdriver until it is freed and then pulling it forward Place the exhaust conduit D in the hole in the ceiling or wall for exhaust of the air Fix the base of the housing B in place using the plugs and screws provided It may also be fixed to the interior of the ceiling using the 2 quickfit Loosen the screws 4 until the wedges 5 are fully concealed in the housings 6 and can be easily introduced inside the pipe Tighten the screws until the wedges 5 firmly fix the extractor to the exhaust conduit Note All installations must be supervised by a qualified electrician Installations and wiring must conform to current IEE regulations UK local or appropriate regulations other countries Do not install the exhaust pipe D of the extractor unit to a chimney ventilation pipe or hot air conduit Before connecting the unit to pipelines consult the local municipal regulations regarding exhaust air and ask the permission o2. d energy com booklet are as accurate as printing processes allow
3. f the person in charge of the building Make sure that the ventilation is appropriate especially when the extractor is used in conjunction with an appliance with a combustion chamber This extractor is designed for the ventilation of homes or similar premises Do not use in premises where the room temperature is above 40 C This extractor does not cause any interference in radio television sets C E E regulation No 89 336 ELECTRICAL CONNECTION The unit must be connected to a single phase mains power supply network at the voltage and frequency indicated on the rating plate of the extractor unit The electrical installation must include a double pole isolating switch with a distance between contacts of at least 3 mm Make the electrical connection by loosening the screw 2 until the cover 3 is free and connect the power supply cables to the connection strip E the blue cable to N and the brown cable to L Replace the cover 3 fixing it in place with the screw 2 and finally press home the cover A until it 1s firmly held by the clip 7 and the catch 1 Fig T Refit the screw SL150 only The appliance must be permanently connected to a fixed electrical supply installation using twin conductor cable of at least 1 mm in section and a maximum of 1 5 mm No earth installation 1s required as the appliance has double insulation Class II A IPX4 NOTE TIMER and HUMIDITY connection Must he carried out by followi
4. installation Do install each fan with a double pole isolating switch Do make sure the mains supply 1s switched off before attempting to make electrical connections or carry out any maintenance or cleaning Guarantee Customers outside UK see international below UK The fan is guaranteed against defects for 2 years from the date of purchase Please keep your purchase receipt f you have any problems contact Xpelair s Head Office at the address shown below Technical advice and service Customers outside UK see international below UK Xpelair have a comprehensive range of services including Free technical advice help desk from Engineers on all aspects of ventilation Free design service quotations and site surveys e Service and maintenance contracts to suit all requirements Please ask for details By telephone on Techline 44 0 8709 000430 By fax on Techfax 44 0 8709 000530 e At the address below International e Guarantee Contact your local distributor or Xpelair direct for details Technical Advice and Service Contact your local Xpelair distributor Xpelair Applied Energy Products Ltd Morley Way Peterborough PE2 9JJ t 01733 456789 Xpelair is a registered trademark of Applied Energy Products Limited f 01733 310606 Applied Energy Products reserve the right to alter product specifications or appearance without prior notice All finishes and diagrams in this www applie
5. ng the wiring diagram for SLIOOT SLIOOHT SLISOHT Connect the wires to the connection strip by using a pointed instrument the tip of a screwdriver for example to apply pressure to x xl x2 x3 and pushing the striped wires L N SL into the holes y yl y2 y3 SL100T A IPX4 Adjust the timer by turning the knob 4 in a clockwise direction to increase the operating time 3 15 SLI00HT and SLISOHT LA IPX4 Adjust the operating time by turning the red knob 4 in a clockwise direction Adjust the level of humidity by turning the blue knob 5 in a clockwise direction to increase the level The Slimline HT series incorporate a LED indicator The LED is lit when the extractor is functioning either activated by the switch fitted to the appliance itself or another exterior switch When the extractor is activated by the level of humidity the LED 1s not lit When the extractor is not operating the LED does not light SL100P and SL150P LIA IPx4 This model is fitted with a Start stop pull switch 6 Fig P Wiring Diagrams FAN FERMINAES DU Le LE iscLATINO BATE SL100P SL150P FAN TERMINALS i JUBLE POLE BOLATING S TCH INTERMAL PULL CORD SWITCH AND MOTOR CONNECTRONE SL100T FAN SL1 OOHT iNIIEFE TEHRMIISAL Ei SLI50HT SWITCH A LAMP Q9 eun FN DOUBLE POLE EOLAING SWITCH Fig T Pull switch circuit Do s and dont s Do read all the instruction leaflet before commencing
Download Pdf Manuals
Related Search