Woodstock D4041 User's Manual
Contents
1. of two M8 1 25 x 50 hex bolts into each T track 9 Place the miter saw over the bolts and secure each location with one washer and two hex nuts see Figure 5 when securing these tighten the top hex nut against the bottom one so they do not work loose from the vibrations that occur while cutting Adjusting Work Stand Extension Arms 1 Slide the extension arms out to their maximum reach and place a straight 2x4 across the miter saw table and rollers 2 Loosen the crossbar knobs and rotate the roller assemblies until the rollers almost touch the 2x4 as shown in Figure 6 Then loosen the roller assembly lock knobs slide the rollers up to touch the 2x4 and re tighten the lock knobs Folding Miter Saw Stand for Storage 1 Remove the support braces retract the extension arms and rotate the support rollers flat 2 Push in the locking pins shown in Figure 7 and fold the legs up into the stand Locking Pin un nm il Figure 7 Folding the miter saw stand lbs D4041 Miter Saw Stand Instructions D4041 Parts sO gt 34 a 1 30 8 24 3 25 N a ADE 29 N FR 28 6 2 REF PART DESCRIPTION REF PART DESCRIPTION 1 XD4041001 ROLLER 18 XD4041018 SMALL AXLE 2 D4041002 3 D4041003 4 D4041004 5 D4041005 6 D4041006 7 D4041007 8 D4041008 9 D4041009 10 __ XPBO6M 11 D4041011 12 XPNO3M 13 XPWFO8M 14__ XPB166M 15 __ xD4041015 16__ XD4041016 17___ XD40410172. saw work stand MITER SAW WORK STAND USAGE Only use EXPERIENCING DIFFICULTIES If at any time the miter saw work stand to support a miter you are experiencing difficulties performing saw This stand is NOT intended for use as a the intended operation stop using this stand ladder or scaffolding Contact Tech Support at 360 734 3482 for help COPYRIGHT JULY 2010 BY WOODSTOCK INTERNATIONAL INC WARNING NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL INC Printed in China ibe D4041 Miter Saw Stand Instructions Inventory In the event that any nonproprietary parts are missing e g a nut or a washer we would be glad to replace them or for the sake of expediency replacements can be obtained at your local hardware store Box Contents Figure 2 Qty A Stand not SHOWN sen 1 B Roller Assembly ss re 2 C Roller CrossDar scecseese ses nennen rriki sait 2 D Wheel Brackets uuu cn ne 4 E WICE eer EEE E E EEA EEEE EREE 2 Hardware Qty Support Braces uusuu BR 2 Hex Bolts M8 1 25 X 45 cece cece ecw ce cece nn 2 Hex Bolts M6 1 x 45 cece cece eee e cee eeees 12 Flat Washers 6MM cccce cece ccc cccececcvces 12 Hex Nuts M6 1 ccc cece cece cece cece ce cececeees 12 Lock Nuts MG 1 25 une 2 Knobs M8 1 25 x 50 ccccceeecececeececesecesesesess 4 Figure 2 Model D4041 inventory Knobs M
3. 8 1 25 X 20 ccc cece cece ccc c ec ee cece ce ceeees 2 Hex Bolts M8 1 25 x 50 cece cece ce cee ee ees 4 Hex Nuts M8 T1 23 2 20 ae 8 Flat Washers 8MM ccccccecececcccececcccvees 6 Assembly 1 Lay the work stand upside down and unfold the top set of legs inset in Figure 3 Make sure the locking pins snap into place 2 Place a wheel bracket on both sides of the wheel and thread 1 M8 1 25 x 45 hex bolt through the assembly see Figure 3 then secure it with 1 8mm flat washer and 1 M8 1 25 lock nut 3 Place each wheel bracket assembly over the stand leg thread 4 M6 1 x 45 hex bolts through each wheel bracket see Figure 3 and secure them with flat washers and hex nuts 4 Unfold the remaining legs install the support braces between the legs with the remaining M6 1 x 45 hex bolts flat washers and hex nuts 5 Place the work stand upright move the bottom of the wheels approximately an s above the floor and tighten the hex nuts 6 Place the roller crossbar between the extension arms Roller and secure them with the M8 1 25 x 50 knobs as M8 1 25 x 20 Knob Assembly shown in Figure 4 Figure 4 Support roller assembly D4041 Miter Saw Stand Instructions 7 Slide the roller assemblies into the crossbars and secure them with the M8 1 25 x 20 knobs see Figure 4 8 Loosen the T track lock knobs and adjust the T tracks to the width of your miter saw then slide the heads
4. Model D4041 Miter Saw Stand Instruction Sheet Introduction The Model D4041 Miter Saw Work Stand Figure 1 features a universal adjustable T track mounting system for securing miter saws without modification Laterally and vertically adjustable ball bearing rollers on each end of the stand support long workpieces Roller mounts rotate incrementally for fine height adjustment Folding legs and rubber wheels make this work stand portable Unpacking This item was carefully packaged for safe transportation Figure 1 Model D4041 If you notice that it was damaged during shipping please contact your Shop Fox dealer immediately AWARNING TO REDUCE THE RISK OF SERIOUS PERSONAL INJURY WHEN USING THIS ITEM 1 MITER SAW SAFETY Follow all safety instruc 5 WORKPIECE BALANCE Use extra support tions in the miter saw manual tables or get assistance when working with large workpieces to prevent the stand from MITER SAW WORK STAND SET UP Make sure tipping over the leg locking pins are fully snapped into place before mounting the miter saw 6 ATTACH MITER SAW SECURELY DO NOT operate the miter saw unless it is securely MITER SAW WORK STAND PLACEMENT Only attached to the miter saw work stand operate the miter saw work stand on a hard flat and level surface DO NOT set up the LOCK WORK SUPPORTS Tighten lock knobs miter saw work stand on a soft surface such to secure the work supports before using the as sand or mud miter
Download Pdf Manuals
Related Search