Winegard TRAVELNET TN-2033 User's Manual
Contents
1. Restart button and confirm by clicking the Restart button again and wait 30 seconds 22 Do a hard restart of all network devices in order first the Cellular Router I the WiFi Router and finally laptop Setting Up WiFi Security on the Edimax BR 6204WG Refer to the Edimax users guide CD for additional information Once you have an internet connection and an unsecure WiFi connection established proceed to setup WiFi security for your Edimax router Ver 1 5 4 1 2009 11 LAN Ports 1 through 4 WAN Por Figure 20 WEP Key Setup G Wem Figure 21 Log into the Edimax WiFi Router at 192 168 2 1 Enter the Username admin and Password 1234 Go to WIRELESS SETTINGS gt SECURITY Encryption type select WEP Key Length 64 bit Key Format Hex 10 Characters Default Tx Key Key 1 Encryption Key 1 Enter your 10 Characters Key see chart below Do not place an x in the selection box labeled Enable 802 1x Authentication for normal installations If there are any questions call TravelNet Technical Support Por O SYS Ver 1 5 4 1 2009 _12 DI NETWORKING PEOPLE TOGETHER gt 44 wy 4 Setup W4Ganeral Setup security This page allows you setup the wireless security Turn on WEP or WPA by using Encryption Keys could prevent any unauthorized access to your wireless network Encryption WEP Me Key Length past Key Format Hex 10 characters v Default2. Edimax Wireless router use the WAN port Figure 19 not the 4 LAN ports Ver 1 5 4 1 2009 sc Figure 6 6 Carefully attach the antenna cables to the SMA Antenna Mounts on the TravelNet router Caution should be taken to not over tighten the SMA cable connectors DB9 Serial Port Ethernet Port Figure 7 7 Connect power supplies for both devices to AC source or 12VDC source When a 12 VDC source order the appropriate pigtail accessories and please save the 12 volt power supply for the coach owner Note that if using RV s DC power the power inputs are polarity sensitive NOTE The lead with the white stripe is 12 VDC Ver 1 5 4 1 2009 5 F rw Ln Pn ry T gt gt A Wi g a EF eget a WY FN i LERN zi ah A Pu X A ae A n P n ne a ya ee m x b mo Mi 4 m 7 z ra a sr y zi Say a vs Tr pleh sd a ll ope fw yd GN Se F W OZ wae Prej 1 Pe y 5 Vie ue Yg W iP We a ep YM Z 4 wa A 7 IF ai z s x a a JA ri 4 ai ry k A ia ij F k n k e r Li f Fw y od kw Toy Y j 4 wY h 4 a a ie ee eee Lee cn PRA ran y aka HI O SMA Antenna Reset Defaut k Senice LAN o SMAAntenna Figure 8 8 Check table below for LED status IP address I XRTT Connection No Signal RSSI Connected to LAN EV DO Connection RSSI lt 88 ss RSSI gt 88 9 If you are activating the TravelNet Cellular Router precede to the activation instruc
3. Tx Key Key 1 z Encryption Key 1 ri NM Encryption Key 2 fo Encryption Key 3 pon Encryption Key 4 fo Enable 802 1x Authentication Apply Y Cancel Figure 22 WEP Key Setup Parameters Default Description Z O Z S O oes Length 64 bit You can select the WEP key length for encryption 64 bit el P or 128 bit Larger WEP key length requires 26 hexadecimal characters Key Format Use hexadecimal digits in the A F a f and 0 9 range to be the WEP Key Examples Hexadecimal Digits 12345abcde or abcdef0123 10 Write key on piece of paper or on Edimax manual and keep in a safe place with other important documentation 11 Click on the Apply Button and wait for the System to automatically Restart Click OK button and security setup is complete 12 Call TravelNet Technical Support 877 475 7771 if there are questions concerning Apple Computers or if you prefer to use other encryption methods Ver 1 5 4 1 2009 13 To connect your XP computer to your wireless network Configuring the Windows XP Wireless Clients With WEP Configuration of the Windows XP wireless clients for WEP key authentication depends on whether you are using Windows XP with SP2 or Windows XP with SP1 and whether the wireless network adapter driver supports Wireless Auto Configuration Wireless Network Adapter Driver Supports Wireless Auto Configuration with Windows XP with SP2 Use the following procedure to con
4. WINEGARD TravejNet A eo TravelNet Internet Only Cellular Router Installation Guide ATTENTION INSTALLER Parts List e TravelNet Cellular Router TN 2033 TN 2055 110 volt adapter with green connector Edimax BR 6204WG WiFi Preconfigured Router 110 volt adapter with plug connector 3 foot Ethernet Cable 2 External Antenna white 2 External Antenna mount with 14 cable 2 Stainless Antenna Mounts Cable Entry Cover Aluminum Ground Plane 7 x 7 Customer Package clear envelope o 7 foot Red Ethernet Cable o 2 Black SMA Antenna o TravelNet Ouick Start o TravelNet User CD e User Manual e Troubleshooting Guide Other items not included e Sealant Consult your vehicle manufacturer for the best sealant for your roof material Ver 1 5 4 1 2009 1 TravelNet s Cellular Router System is Preconfigured And Ready to Install with these Easy Steps Installation Instructions 1 Install the TravelNet Router and Edimax Router equipment in a convenient place such as upper cabinet Velcro works well on the base of the each unit Mount the unit so that the diagnostic lights can be viewed without moving the TravelNet Router and the Edimax Wireless Router 2 Locate the 2 antennas on the roof away from other obstructions Also you will need sealant as recommended by your coach manufacturer stainless screws 4 to anchor the aluminum ground plane to roof cable clips to anchor cable cable entry cover plate Warning You m
5. ability is Ok for Activation then go to step 9 if Not Ok then wait 3 minutes If still Not Ok call support Ww ee Travel Z Over The Air Activation Net vver Ire AIT Acuvatori Adivete otatus Details Back Figure 17 10 Click on the Activate button 11 Wait 3 minutes then click the Status button If still in progress then wait an additional 3 minutes If still in progress or failed contact support 12 When status changes to Activated click the Back button 13 Click on the Home button 14 Click on the Interfaces Wireless button and change the Wireless connection type to Enable refer to fig 17 Ver 1 5 4 1 2009 10 Travels A Trave A Wireless interface Configuration Net guration Network Select 0 Auto Change to Enable User Name Wireless Connection Disabled Password Inactivity Timeout Never Use network provided dynamic IP address Use the following static IP address Enable LCP echo packets O Figure 18 15 At the bottom of the page click the Update button 16 Ok then click the Home button 17 Click on the Restart button and confirm by clicking the Restart button again and wait 30 seconds Admin Screens Activation Restart Winegard Website Figure 19 18 Click on the Home button 19 Click the Status Wireless button verify that there is a Current IP address 20 Click on the Home button 21 Click on the
6. e oLaLus Current IP Address ESN Dec 09603911949 ESN Hex 6087FCA4D System ID 20 Phone Number MDN 0000004665 Network Status In Service Signal Level RSSI H9dEm Service Type 1xRTT EvDO Rev A Current IP Address Band Cellular Call Status Idle Roam Status Not Roaming Temp Alert Temp OK Home Refresh Details Figure 13 20 Click on the Home button 21 Click on the Restart button and confirm by clicking the Restart button again and wait 30 seconds 22 Do a restart of all network devices in order first the TravelNet Router 2nd the Edimax Router and finally laptop Sprint TN 2033 Activation 1 Connect an Ethernet Cable directly to the TravelNet Cellular Router and the Laptop Enable the Local Area Network when connected go to the next step Open a web browser Internet Explorer Firefox Chrome Mozilla Enter the IP address 192 168 1 10 aW mau T Figure 14 a WINEGARD Travel Net Internet Only User Name etek Password popa Log In Figure 15 Ver 1 5 4 1 2009 9 Enter the user name ctek and password ctek Click the Log In button Click on the Activation button Click on the Over the Air Activation button aa o om D TravelNet 5 Wireless Activation Services J Wireless AcLIVall l Services Local PRL Update select Over The Air PRL Update Select Over The Air Activation Select Manual Configuration select Home Figure 16 9 If Network St
7. figure Windows XP with SP2 for your infrastructure mode wireless network when the wireless network adapter supports Wireless Auto Configuration l D 8 9 When the computer is within range of the wireless router or Access Point AP operating in your home or small business Windows XP should detect it and prompt you with a Wireless networks detected message in the notification area of your taskbar Click the notification message If you are not notified right click the wireless network adapter in Network Connections then click View Available Wireless Networks In either case you should see a Choose a wireless network dialog box with the name of your wireless network If the TravelNet xxxx wireless network is not displayed it may be necessary to reset the unit by removing its power plug for 10 seconds then reinsert the power plug and wait 45 to 60 seconds Then select the View Available Wireless Networks again Double click your wireless network name Windows XP will attempt to connect to your wireless network Because Windows XP has not been configured with the WEP key for your wireless network the connection attempt will fail and Windows XP will prompt you with a Wireless Network Connection dialog box Type the WEP key in Network Key and Confirm network key and then click Connect If the status message for your wireless network in the Choose a wireless network dialog box is Connected you are done If the status
8. message for your wireless network in the Choose a wireless network dialog box is Authentication did not succeed click Change the order of preferred networks in the list of Related tasks From the Wireless Networks tab of properties of your wireless network adapter click the name of your wireless network in Preferred networks and then click Properties In Network Authentication click WEP In Network key type the WEP key as configured on the wireless Access Point AP In Confirm network key retype the WEP key Click OK to save changes to the wireless network Click OK to save changes to the wireless network adapt Ver 1 5 4 1 2009 APA To connect your Windows Vista computer to your wireless network View and connect to available wireless networks T Applies to all editions of Windows Vista If you have a mobile PC you can see a list of available wireless networks and then connect to one of those networks no matter where you are The wireless networks appear only if your computer has a wireless network adapter installed and the adapter is turned on 1 Open Connect to a Network by clicking the Start button and then clicking Connect to 2 In the Show list click Wireless You ll see a list of the wireless networks currently available If you do not see a network listing similar to this example TravelNet 1234 it may be necessary to reset power on the WiFi router wait 45 to 60 seconds and refresh the View Available Wirele
9. ss Networks You ll see a list of the wireless networks currently available 3 Click a network and then click Connect If you don t see the network you want to connect to click Set up a connection or network A list of options will appear that includes manually searching for and connecting to a network as well as creating a new network connection Some networks reguire a network security key or passphrase To connect to one of those networks ask the network administrator or the service provider for the key or passphrase Enter WEP encryption key in same manner as described on previous page for Windows XP Whenever possible you should connect to security enabled wireless networks If you i do connect to a network that is not secure be aware that someone with the right tools can see everything that you do including the websites you visit the documents you work on and the user names and passwords that you use After you re connected you can close the Wireless Network Connection window Now you re ready to browse the Web wirelessly You can also create a wireless network in your home RV or boat that connects your computers printers cameras games and other accessories for easy access and enjoyment Ver 1 5 4 1 2009 15 QUESTIONS CALL OUR SUPPORT LINE 877 475 7771 or visit our website FAQ at htip www winegard com TravelNet Winegard Company Support 877 475 7771 FAX 847 991 3328 Ver 1 5 4 1 2009 16
10. tions for the correct TravelNet model See below Sprint or Verizon 10 If the unit has been previously activated now start your computer connect to the wireless network launch a browser window and open a website to test your internet connection If this test is successful then your setup and the installation is complete If a problem arises check our troubleshooting guide in the User Manual CD or call our support line 11 Attention Installer Place consumer information package in cabinet or drawer for your customer Ver 1 5 4 1 2009 _6 Activation Instructions for model TN 2055 and TN 2033 Sprint TN 2033 users skip to page 9 Verizon TN 2055 Activation 1 Connect an Ethernet Cable directly to the TravelNet Cellular Router and the Laptop 2 Enable the Local Area Network when connected go to the next step 3 Open a web browser Internet Explorer Firefox Mozilla Safari 4 Enter the IP address 192 168 1 10 dah http jj192 168 1 10 Figure 9 WINEGARD TravelNet gt internet Only Log ln Figure 10 5 Enter the user name ctek and password ctek 6 Click on the Login button 7 Click on the Activation button Ver 1 5 4 1 2009 7 WINEGARD TravelNet A Internet Only Wed Jan 15 07 55 4009 Release CK415 3 00 0 INTERFACES STATUS SERVICES OPTIONS Wireless Wireless Password Applications Ethernet Ethernet Routing Tools Racie TCF FAD Relay Input UDF FAD Rela
11. ust connect antennas to the SMA style antenna connectors on the TravelNet Cell Router before turning it on Failure to do this could result in erratic start up behavior and could possibly damage the unit Figure 1 Position the antennas near the cable entry point Here the TravelNet unit was located in the front overhead Figure 1 with the antennas mounted close by on the roof Ver 1 5 4 1 2009 yee Figure 2 Note that the antenna mounts are anchored to the 7 x 7 aluminum ground plane and that everything is well sealed Brass Antenna Figure 3 3 Insert the small end of the cable through the 34 diameter hole in the stainless antenna mount and feed the cable through Next screw the brass antenna mount nut to the antenna mount as shown above with the O ring down and attach the Antennas Locate the antenna mounts as shown and attach the stainless Antenna mounts securely to the ground plane and coach roof as shown Secure the antenna cable to the roof as shown Ver 1 5 4 1 2009 ne Figure 4 4 Route the 2 antenna cables to the cable entry hole in the coach roof Securely attach the cable entry cover over the cable entry point on the coach roof using screws and caulk Figure 6 Antenna cables should be directed to the TravelNet Router M Figure 5 5 Attach the 3 foot Ethernet cable to the TravelNet router s Ethernet port and the Edimax wireless router Note there are 5 ports on the
12. y Qutput Admin screens Actrvation Festart Winegard Website Figure 11 8 Click on the Over The Air Activation button 9 If Network Stability is OK For Activation if Not Ok for Activation wait 3 minutes If Not OK for Activation for 15 additional minutes contact Support 10 Click the Activate button 11 Wait 3 minutes then check status If still in progress wait an additional 3 minutes If still in progress or failed contact support 12 When Activated click Back button 13 Click the Home button 14 Go to Interfaces Wireless and Wireless Connection and Select Enable refer to figure 11 WIN E GAR D TravelNet 5 Wireless Interface Configuration a Network Select 0 Auto d Change to Enable User Name Wireless Connection Disabled gt Password Inactivity Timeout Never Use network provided dynamic IP address Use the following static IP address Enable LCP echo packets I Figure 12 15 At the bottom of the page click the Update button 16 Click on the Home button 17 Click on the Restart button and confirm by clicking the Restart button again and wait 30 seconds 18 Click on the Home button Ver 1 5 4 1 2009 _Q 19 Click on the Status Wireless button and verify that there is a Current IP address This may take several minutes depending on the carrier network Tavla A Trave a Wireless Interface Status Net yW EI amp CSS iT1L6TlaC
Download Pdf Manuals
Related Search