Whirlpool RHH 2300 User's Manual
Contents
1. are in the narrow neck of the keyhole stot Figure 2 10 Complete electrical wiring in the juction box according to the National Electrical Code and applicable local codes 11 Replace junction box cover 12 Seal holes around ventilating pipe and wiring passing through ceiling or outside wall with caulking or insulation to prevent energy loss NOTE It has been found that a large part of the energy loss of the average home is due to outside air infiltrating the structure Seal around duct work where it passes through outside walls or ceiling Seal around electrical wiring and be sure the damper is working properly TO INSTALL RANGE HOOD KEYHOLE SLOTS a gt VENTING x KNOCKOUT er 47 9 CM gt Si I ecm Luena KNOCKOUT FIG 1 KEYHOLE SLOT IN CANOPY pra SCREW IN INSTALLATION PARTS BAG JUNCTION BOX COVER LIGHT LENS FIG 2 ALUMINUM FILTER CABINET CUTOUTS 4 10 2 CM Mai vaii 133M STARTER HOLES FIG 4 6 92 OPERATION AND CARE OF UNIT CARE OF FILTERS ALUMINUM FILTER For greater efficiency the permanent type aluminum filter should be removed and cleaned periodically To clean the filter should be soaked in hot water and detergent and thoroughly rinsed The aluminum filter can be cleaned in a dishwasher LIGHTS Do not use bulb larger than 60 watts in light socket CARE OF FAN MOTOR Fan motor has life time sealed bearings2. INSTALLATION and OPERATING INSTRUCTIONS for lt gt Whirlpool VENTED RANGE HOOD ren 2300 senes For most efficient operation the top of the hood should be approximately 66 inches 137 6 cm from the floor See Figure 5 for examples of two typical ductwork installations Choose the best method for your installation 1 Mark locations for ventilating duct and electrical wiring from dimensions given in figure 1 2 Cut holes at marked locations to accomodate ventilating duct and electrical wiring Allow 1 91 cm extra on ventilating opening toward the front of the cabinet directly above the hood See Figure 4 Be sure to minimize openings through the outside walls or ceiling These will have to be sealed later 3 Run the wire through the wall or cabinets according to the National Electrical Code and applicable local codes DO NOT turn power on until installation is complete 4 Remove the screws holding the junction box cover See Figure 3 5 Lift the hood into position and mark the hole locations on the cabinet for each of the four keyhole mounting slots 6 Remove the hood and start all four screws in the center of the narrow neck of the keyhole slot marked on the cabinet bottom See Figure 2 7 Install proper ductwork Lift the hood into position simultaneously feeding the electrical wire through the knockout 9 Tighten the four mounting screws to secure the hood to the cabinet Be sure the screw heads
3. g or Servicing Should you not find a listing dial free the Whirlpool COOL LINE service assistance telephone number 800 253 1301 When calling from Michigan 202020005 Dial 800 632 2243 Alaska amp Hawaii Dial 800 253 1121 If you move Call the TECH CARE service representative in your local area He ll see to the installation of WHIRLPOOL appliances in your new home promptly expertly and fairly priced to you Helpful hints You can help your TECH CARE service representative give you faster service if you include the model and serial number of your appliance when requesting service Also retain your sales slip and warranty to verify your warranty status Remember Your TECH CARE service representative is specially trained in the expert repairing and servicing of your WHIRLPOOL appliances He can help you maintain the quality originally built into your WHIRLPOOL appliance So why not take the time now to look up his telephone number and jot it down in the space provided below My TECH CARE Service representative s telephone number is Range hood model number Range hood serial number Purchase and or installation date lt gt Whirlpool CORPORATION Benton Harbor Michigan Automatic Washers Clothes Dryers Freezers Refrigerator Freezers Ice Makers Dishwashers Built in Ovens and Surface Units Ranges Microwave Ovens Food Waste Disposers Compactors Room A
4. ir Conditioners Dehumidifiers Central Heating and Air Conditioning Systems P N 830721 7 20 79 A625 788
5. that never need oiling under normal usage A few drops on each bearing after three years of heavy usage will prolong the motor life Clean motor with a damp cloth and grease cutting detergent when a heavy coating of grease has accumulated CARE OF EXTERIOR SURFACES Your range hood is a beautifully finished addition to your kitchen and requires only the care you give your range to preserve its lasting beauty Clean with a mild detergent to preserve finish DO NOT use abrasive cleaners HOOD WIRING DIAGRAM HORIZONTAL VENTING IF RAIN CAP HAS A DAMPER REMOVE DAMPER BLADE DAMPER FROM HOOD H IF RAIN CAP HAS A DAMPER REMOVE DAMPER BLADE FROM HOOD VERTICAL VENTING 34 x10 RECTANGULAR FIG 5 PULL TAB TOWARD CENTER AND OUT TO REMOVE FILTER PRESS IN TOWARD CENTER AND OUT TO REMOVE LIGHT LENS CLEAN WITH WATER AND MILD DETERGENT FIG 6 Whirlpool tranchised TECH CARE service If your WHIRLPOOL appliance ever needs service any where in the United States help is just a phone call away to your nearest TECH CARE service representative Whirlpool maintains a nationwide network of franchised TECH CARE service companies to fulfill your warranty and provide after warranty service and maintenance to keep your WHIRLPOOL appliance in peak condition You ll find your nearest TECH CARE service company listed in your local telephone book Yellow Pages under Washers Dryers Repairin
Download Pdf Manuals
Related Search