Home

Westell Technologies Versalink 327W User's Manual

1. 6 4 1 Installation via 10 100 Base T Ethernet NOTE Before you connect via 10 100 Base T you must have an available Ethernet card installed in your computer If your Ethernet card does not auto negotiate you must set it to half duplex Refer to the Ethernet card manufacturer s instructions for installing and configuring your Ethernet card 1 Connect the power supply cord to the power connector marked DC 12V on the rear panel of VersaLink Plug the other end of the power supply into a wall socket and then turn on the modem 2 Connect the DSL phone cable from the connector marked kA on the rear panel of VersaLink to the DSL equipped telephone line jack on the wall IMPORTANT Do not use a DSL filter on this connection You must use the phone cord that was provided with the kit a a el 3 Connect the yellow Ethernet cable from any one of the Ethernet jacks marked i on the rear panel of VersaLink to the Ethernet port on your computer Repeat this step to connect up to three additional PCs to VersaLink NOTE You may connect to any of the four Ethernet jacks on the rear panel as they serve as an Ethernet switch However when using the optional uplink port E1 Ethernet LAN connection is limited to ports E2 E3 and E4 4 Check to see if the DSL LED is solid green If the DSL LED is solid green VersaLink is functioning properly 5 Check to see if the Ethernet LED is solid green Solid green indicates that the Ethern
2. Bppvlce Mame Service Mode Host Device SI veuwr feel is enabled phe All molec ake precedence over the Znruteee dating custom service S If you selected new from the preceding Service Configuration screen the Create new Service Profile pop up screen will be displayed Click on OK to begin creating your new NAT service profile Click Cancel if you do not want to create a new NAT service profile Microsoft Internet Explorer 2 Create new Service Profile Cancel 030 300500 Rev A 48 October 2006 M User Guide VersaLink Gateway Model 327W If you clicked OK the following screen will be displayed Select A New Service Profile 1 from the Current Profile drop down arrow WESTELL Diisi Beatie eaa Here Stata Configuration Mainkenance Troubleshooting Hein Sorvior CGopnflgtrrotbon Curent Profile Defeat mg 8 Darata Quinton Serve UPHP Enable J Sarvicn Anmut Service Moda Host Device P IF yai firewall Geratiecd he firewall rund oke Gegcgcdgecg over be Ganvices del Ine custom SEI LUC ug If you selected A New Service Profile 1 from the Current Profile drop down arrow the following screen will be displayed This screen shows that you have chosen to create a new NAT service profile You may create up to four NAT service profiles and attach an unlimited number of services to each profile Via WESTELL tuacover Wetter Broadbans Home Status Configuration Mainten
3. 1 Goto the Apple icon in the upper right corner of the screen and select System Preferences 2 From the System Preferences screen click on the Network icon The Network screen will be displayed 3 From the Configure field in the Network screen select Built in Ethernet 4 View the IP address field An IP address that begins with 192 168 1 should be displayed NOTE The DHCP server provides this IP address If this IP address is not displayed check VersaLink s wiring connection to the PC If necessary refer to section 5 for hardware installation instructions yt Et Network Ce A Show All Displays Sound Startup Disk Network Location Westell EN Configure Built in Ethernet EA f TCP IP PPPoE li AppleTalk Y Proxies Configure Using DHCP ai Domain Name Servers Optional IP Address 192 168 1 15 Provided by DHCP server DHCP Client ID Optional Search Domains Optional Ethernet Address 00 30 65 e1 84 ba Example apple com earthlink net O Click the lock to prevent further changes 030 300500 Rev A 29 October 2006 We WESTELL User Guide VersaLink Gateway Model 327W Create a User Account In the address window of your Internet Explorer web browser type http dslrouter Press Enter on your keyboard OO WireSpeed Dual Connect e P G amp Refresh Home AutoFill Print Mail R a eed T Live Home Page CY Apple 2
4. If you click on the drop down arrow at DHCP Server a list of options will be displayed If you want to disable your DHCP server select Off from the DHCP Server drop down arrow Click on save 3 DHCP Configuration Microsoft Internet Explorer File Edit View Favorites Tools Help WESTELL yaaa Discover Better Broadband Home Status Configuration Maintenance Troubleshooting Help DHCP Configuration DHCP Server Private LAN D Off Private Frese ICP Settings DHCP Start Address 192 168 1 15 DHCP End Address 192 168 1 47 DHCP Lease Time fi fo ID fo Days Hours Minutes Seconds 030 300500 Rev A 73 October 2006 WESTELL User Guide VersaLink Gateway Model 327W If you selected Off at DHCP Server the following screen will be displayed Click on save to save the DHCP Server setting DHCP Configuration Microsoft Internet Explorer Discover Setter Broadband Home Status Configuration Maintenance Troubleshooting Help H DHCP Configuration DHCP Server or D If you clicked on save in the preceding DHCP Configuration screen the following pop up screen will appear Click on OK Microsoft Internet Explorer 2 Save and reconfigure DHCP IMPORTANT After you disable the DHCP server you must reboot your PC 030 300500 Rev A 74 October 2006 User Guide VersaLink Gateway Model 327W 12 5 4 Enabling the DHCP Server If you want to enable your DHCP Server settings select Private LAN at the DHC
5. User Guide VersaLink Gateway Model 327W 13 5 Static NAT If you select Services from the Configuration menu the following screen will be displayed showing the static NAT button Static NAT allows you to configure VersaLink to work with the special NAT services NOTE When the Gateway is configured for Static NAT any unsolicited packets arriving at the WAN would be forwarded to this device This feature is used in cases where the user wants to host a server for a specific application IMPORTANT Single Static IP must be disabled if it has been enabled previously before you enable static NAT To disable Single Static IP select Single Static IP from the Configuration menu Next click on the disable button and then click on OK in the pop up screens to allow the Gateway to be reset As explained in section 12 1 Single Static IP you must reboot your computer after you enable or disable Single Static IP After you have rebooted your computer return to static NAT configuration screen by selecting Services from the Configuration menu and clicking on the static NAT button WESTELL Disses Heter Beste Home Status Configuration Malnienan ce Troubleshooting Help 030 300500 Rev A 119 October 2006 A WESTELL User Guide VersaLink Gateway Model 327W 13 6 Enabling Static NAT Before you enable static NAT you must select Default from the Current Profile drop down box Static NAT must be configured for the Gateway s defaul
6. WESTELL VERSALINK GATEWAY MODEL 327W USER GUIDE Copyright 2006 Westell Inc 030 300500 Rev A Pa WESTELL User Guide VersaLink Gateway Model 327W TABLE OF CONTENTS 11 12 PRODUCT DESCRIPTION eege 4 SAFETY CNR ET e NL KEE 4 REGULATORY INFORMATION ENEE 5 3 1 PG Oi TAC EE 5 52 Canada Cori ication EE 6 NETWORKING EIB EIER KT 8 SERRURIER BU EE 9 5 1 EE 9 52 Cable Connectors and Switch Locanons eeens sses ssssssssssssssssssssssssssssssssssssssssssssssssssssssssse 10 5 3 Connec or TEE II 5 4 reet E 1 INSTALLING THE HARDW AR E 12 6 1 Tris Call ster e remens senisesse E ari 12 6 2 CLOGS VOU EE Ee 12 6 3 ere 12 6 4 Hardware Installations yo ceonceccieeevanccnnseasicoteranceun snaokeunsuenceeetnatie sbesenseensuacteunesanseenenasieuboneomeensnacboumepensemeenaates 13 CONFIGURING VERSALINK FOR INTERNET CONNECTION 17 7 1 Setting Up an Account Profile eneeneesssssseeoeeeeeeressssssssssssecereereesssssssssssseeerereresssssssssseeeeeerressssssssssseees 17 pe EEN 22 7 3 Establishing a PPP S68 EE 24 7 4 Disconn cting a PPP EENEG EE 26 SETOING UP MACINTOSH OS XAecnciciesniipii iin aE E O aE S 2 SETTING UP ADVANCED CONFIGURATION EEN 32 Le E 33 101 Adding Account D re 34 102 Edin Account Prolls eses E R EE EE E E aE 35 SLATO E 37 lil eene e e E E 37 M2 SRD OUL E A A E A EE E E A E E A N A E 38 CONFIGURA UN RE 39 12 1 Single Static IP Single IP Address PassThrough eeeseesossssssssooeeen
7. select box 030 300500 Rev A 116 October 2006 Pe WESTELL User Guide VersaLink Gateway Model 327W The NAT service for which you are configuring Port Forwarding The type of NAT service configuration you selected Protocol The type of Protocol that is used to run this NAT service TCP Transmission Control Protocol UDP User Datagram Protocol UDP Local IP Address If a static IP address has been assigned it will be displayed here Base Host Port The port on the WAN that will host the NAT service selected Base Host Port is the first port that will be used for a specific service when configured for a range of ports 13 3 Port Forwarding Trigger Ports To select Port Forwarding Trigger Ports click on define custom service from the Service Configuration screen and then select Trigger Ports from the Custom Service screen Click on next The follow settings will be displayed in the Trigger Ports screen Enter your values in the Local Trigger Port Range fields and click on next to continue 28 Custom Service Microsoft Internet Explorer El Trigger Ports Microsoft Internet Explorer Custom Service Trigger Ports Set Up a Port Forwarding entry based on your specific Set Up a Trigger Port Forwarding entry based on your ports specific ports C Port Fowarding Forward a range of WAN ports ta Service Name Custom Trigger Port an IP address on the LAN The above name will be saved Forward a range of ports to an
8. DSLATM PORT or ETHERNET PORT 1 However all menu options are displayed if VersaLink is configured for DSLATM PORT 1 The following sections provide further details on the Troubleshooting menu L n aiband Home Status Configuration Maintenance Troubleshooting Help System Self Tests Diagnostic Logs Statistics Status 15 1 System Self Tests The following settings will be displayed if you select System Self Tests from the Troubleshooting menu Click on test all to run a diagnostic test on VersaLink s connection Discover Setter Broadband Home Status Configuration Maintenance Troubleshooting Help System Self Tests Connection Status DSL Up PPPoE Session up PPP Connection up Test Description Test Results Self Test PING ISP s Router DNS E www yahoo com host name IP Address PING S e 4 23 144 67 IP address or host name EZB Trace Route 030 300500 Rev A 133 October 2006 WESTELL User Guide VersaLink Gateway Model 327W If you want to PING using the System Self Test screen diagnostics page shown above enter your DNS or IP address in the fields provided and click on the test button The System Self Test will run a diagnostic test that executes independent of firewall security settings See the following table for test descriptions and possible responses If you want to PING using the MS DOS shell window first you will need to check your firewall security setting If you PING via DO
9. VC 1 Bridge Settings Proxy Bridge 030 300500 Rev A 100 October 2006 WESTELL User Guide VersaLink Gateway Model 327W If you selected VLAN Bridge under VC 1 Bridge Settings the following screen will be displayed Enter the appropriate values in the fields and click on set VC Configuration verb vcas perho Qos UBR sl Protocol Bridge sl Status Enabled MCL Bridge Settings Mode WYLAN Bridge e 3 YLAN ID E LAN Priority 3 gt VLAN on WAN C Enable Disable Help x ite T lee VC 1 Bridge Settings VLAN Bridge Mode The Mode you have selected to use with Bridge protocol VLAN is used to assign VLAN tags to individual data ports on the modem VLAN ID Assigns a VLAN ID to the port VLAN Priority This will set the VLAN priority for the port VLAN on WAN Factory Default DISABLE Selecting Enable allows VLAN tagging to occur according to the data port s configuration 030 300500 Rev A 101 October 2006 Pe WESTELL User Guide VersaLink Gateway Model 327W After you have configured the VC 1 Configuration screen you must click the set VC button to save your VC settings VC 1 Configuration vil vc perho Qos UBR sl Protocol Bridge H Status Enabled VC 1 Bridge Settings Mode Routed Bridge DHCP Client Enable Disable IP Address nunn o Subnet Mask 255 255 255 255 E Gateway nunn DNS Primary nun DNS Secondary nunn l set VC Cancel Help If you clic
10. 0 0 0 0 20 US Tx Power 11 1 DS Tx Power 8 7 0 0 0 20 US DSL Rate 992 kbits sec DS DSL Rate 8064 kbits sec 0 0 0 20 WanMor reports DSL is UP 0 0 0 14 Set time zone offset to 6 00 0 0 0 0 Model Number 490 327W10 06 0 0 0 0 Software Version YER 03 00 41 0 0 0 0 Product WireSpeed Data Gateway Model 4 Port Gateway 0 0 0 0 YVLYNQ_WLAN successfully started end of diagnostic log file Clear diagnostic log printable savable format 030 300500 Rev A 137 October 2006 WESTELL User Guide VersaLink Gateway Model 327W 15 2 1 Saving the Diagnostic Log File If you want to save the diagnostic log file go to your Browser s menu and select File then select Save As from the drop down menu e Diagnostic Logs Microsoft Internet Explorer File Edit View Favorites Tools Help New D Open Chat Edit with Netscape Navigator Save Etits Page Setup Print Ctrl P Print Preview Send Import and Export Properties Work Offline Close Date March 18 2004 Time 14 14 55 LOGS Select a log D Ra Genen Remote Logging Enable I Remote IP Address 192 168 1 47 At the Save Web Page dialog box select a destination for your log file from the Save in drop down arrow Next enter a name for your log file in the field labeled File name and click on Save save Web Page EZ x Save in Ca Diagnostics Log ES File name Log File Name Save as type Web Page complete
11. 0 0 0 0 Subnet Mask 255 255 255 255 Gateway 0 0 0 0 DNS Primary 0 0 0 0 DNS Secondary 0 0 0 0 Help H lfae einen OO 030 300500 Rev A 106 October 2006 M WESTELL User Guide VersaLink Gateway Model 327W If you click on set the following pop up screen will be displayed Click on OK Microsoft Internet Explorer 2 Set this WAX configuration Cancel If you clicked on OK in the preceding pop up screen the following pop up screen will appear VersaLink must be reset to allow the new configuration to take effect Click on OK Microsoft Internet Explorer The modern must be reset in order for the new configuration to take affect Do you wish to reset now If you clicked on OK in the preceding screen the following screen will be displayed VersaLink will be reset and the new configuration will take effect E Edit View Favorites Tools Help Wk L cl Links se D Discover Setter Broadband Home Status Configuration Maintenance Troubleshooting Help Resetting Modem Please Wait The modem is resetting in order for the requested changes to take effect Your page will be reloaded shortly 4 L E Done a Internet 7 030 300500 Rev A 107 October 2006 M User Guide VersaLink Gateway Model 327W After the modem has been reset the WAN Configuration screen will display Routed Bridge as the protocol for ETHERNET PORT 1 WAN Configuration Microsoft Internet Explore
12. 1 47 00 50 da b2 d9 fl salle 982 Active sii 030 300500 Rev A 144 October 2006 Pe WESTELL User Guide VersaLink Gateway Model 327W 15 5 2 Wireless Stations The following settings will be displayed if you select Wireless from the Status menu NOTE A Wireless device must be connected to the Gateway for the fields in this screen to be populated Wireless Stations Microsoft Internet Explorer File Edit view Favorites Tools Help address http 192 168 1 1 802_11_stations htm a At Discover Better Broadband Home Status Configuration Maintenance Troubleshooting Help Wireless Stations Wireless Station List Station MAC Address State PBCC Active Rate 1 00 03 2f 25 ef c9 Authorized Active 54 Mbit sec Wireless Stations List This number indicates the order in which the stations are first accessed by VersaLink Packet Binary Convolutional Code modulation Active Rate The current transmit and receive rate 030 300500 Rev A 145 October 2006 WESTELL User Guide VersaLink Gateway Model 327W 15 5 3 RIP Table The following settings will be displayed if you select RIP Table from the Status menu NOTE RIP must be enabled for this table to be populated 3 RIP Statistics Microsoft Internet Explorer Discover Better Broadband Home Status Configuration Maintenance Troubleshooting Help RIP Statistics RIP Network Routing Table Destination Netmask Gateway Metric RIP Host Rou
13. 11b only Communication with VersaLink is limited to 802 1 1b 11b Stations using any of the 802 11b and 802 11b rates can communicate with VersaLink 11g only Communication with VersaLink is limited to 802 11g 4x Support Factory Default Disabled When selected this enables disables the 4X option If enabled 4X support provides additional algorithms for increased throughput The station cards must also support this option Hide SSID Factory Default Disabled wf If Enabled VersaLink will not bradcast the SSID Stations must configure the SSID to match the Network Name SSID to connect to VersaLink If you click save in the Wireless Configuration screen the following pop up will be displayed Click OK to save the settings Microsoft Internet Explorer X 5 a K Wireless access will be interrupted and the wireless stations may require reconfiguration continue Cancel 030 300500 Rev A 61 October 2006 M User Guide VersaLink Gateway Model 327W 12 4 2 Wireless Security The following screen will be displayed if you select Wireless and then select Security from the Configuration menu WESTELL Discover Better Broadband Wireless Securit Home Status Configuration Maintenance Troubleshooting Help Wireless Security Wireless Security Disabled D 030 300500 Rev A 62 October 2006 a WESTELL User Guide VersaLink Gateway Model 327W At the Wireless Security drop down menu s
14. 2006 Pa WESTELL User Guide VersaLink Gateway Model 327W FY preamble algorithm is used Otherwise the long preamble algorithm is used Slot Time Algorithm Factory Default Local STA s Possible Response Always Off Transmissions are done using a 20 usec slot time Always ON Transmissions are done using a usec slot time SST Local STA s If all associated stations support SST then the 9 usec slot time is used Otherwise the 20 uses slot time is used Enhanced Dynamic Similar to Local STA s with the following extension If associated stations that do not support SST do not transmit for a period of time the 9 usec slot time is used PBCC Algorithm Factory Default Enhanced Dynamic Possible Response Always Off PBCC is not used operation at 22 Mbps is not possible Always ON PBCC is used Local STA s If all associated stations support PBCC then PBCC is used Otherwise PBCC is not used Dynamic Similar to local STA s with the following extension PBCC setting is also dependent on Beacon frames from overlapping BSS If Beacon frames are received that do not support PBCC then PBCC 1s not used Enhanced Dynamic Similar to Dynamic with the following extension If associated stations that do not support PBCC do not transmit for a period of time then PBCC is not used ERP Protection Algorithm Factory Default Dynamic Possible Response Always Off ERP is not used Always ON ERP is used Local STA s If
15. 256 bit WEP encryption If WEP is selected any station can connect to the AP as long as its SSID matches the AP SSID If wireless security is disabled the risk of someone nearby accessing the AP is maximized Authentication Type Factory Default Open System Possible Response Open System Open System authentication is the default selection Shared Key To use Shared Key authentication WEP must be enabled and a valid WEP key must be present Enabling WEP does not force the use of Shared Key authentication It is permissible to have WEP enabled and still use Open System authentication Key Select If selected the WEP Key is treated as a string of text characters and the number of characters must be either 5 for 64 bit encryption or 13 for 128 bit encryption or 29 for 256 bit encryption If not selected the WEP key is treated as a string of hexadecimal characters and the number of characters must be either 10 for 64 bit encryption 26 for 128 bit encryption or 58 for 256 bit encryption The only allowable hexadecimal characters are 0 9 and A F NOTE The WEP key must be the same value and type for both VersaLink and the wireless network adapter Pass Phrase is not the same as text and should not be used 030 300500 Rev A 65 October 2006 Ww WESTELL User Guide VersaLink Gateway Model 327W 12 4 3 Wireless MAC Filter Table The following screen will be displayed if you select Wireless and then select MA
16. 2644 TCP 8000 TCP a 3 27660 UDP Each computer playing QuakellII must use a different port number starting at 27660 and incrementing by 1 You ll also need to do the following 1 Right click on the QIII icon 2 Choose Properties 3 In the Target noe you ll see a line like C Program Files Quake III Arena quake3 exe 4 Add the Quake III net_port command to specify a unique communication port for each system The complete field should look like this C Program Files Quake HI Arena quake3 exe set net_port 27660 5 Click OK 6 Repeat for each system behind the NAT adding one to the net_port selected 27660 27661 27662 6970 32000 UDP 554 TCP UDP ment TT OoOO UDP 6970 to 7170 UDP 3783 BaseStation BBTO o Tiberian Sun amp Dune 2000 1140 1234 4000 TCP UDP Ultima Online 5001 5010 TCP 7775 7777 TCP 8800 8900 TCP 9999 UDP 7875 UDP Unreal Tournament server 7777 default gameplay port 7778 server query port 7779 7779 are allocated dynamically for each helper UdpLink objects 030 300500 Rev A 152 October 2006 a WESTELL User Guide VersaLink Gateway Model 327W Application Game Port Protocol including UdpServerUplin objects Try starting with 7779 7781 and add ports if needed 27900 server query if master server uplink is enabled Home master servers use other ports like 27500 Port 8080 is for UT Server Admin In the UWeb WebServer section of the server ini file set the ListenPort to 8080 and
17. Address RulesPassurDP pass protocol udp to port 53 gt gt done pass protocol udp from port 53 gt gt done Rulestdropicup drop protocol icmp gt gt alert 4 ICMP Message To HAN IF end NOTE The information displayed in this screen depends on the level of security you have selected g KE Dones OO O O l e O If you clicked save in the User Define Firewall Rules screen the following pop up screen will be displayed Click OK when asked Do you wish to save these Rules to Flash and switch you Security Level to User This will save your new firewall settings If you click Cancel your new firewall settings will not be saved Microsoft Internet Explorer KS in S Do wish to save these Rules to Flash and switch your Security Level to User Cancel 030 300500 Rev A 58 October 2006 User Guide VersaLink Gateway Model 327W If you select Help in the screen labeled User Defined Firewall Rules the following screen will be displayed This screen gives a detailed explanation of the Firewall Rules 030 300500 Rev A FileButfer Format The ADL file or buter bemat Lo died into teg sections The ties portion ofthe din denos any nyniber of keys and associahed vals The SECON De Cortana Ihe D enpo rule detnitierrs Key Definition Section Aker datindion consists of tee key followed by the accociaied value Awalue is achially a charecier string The siring ig delimited Fo the open e ORE SQudne bret kets A
18. Apple Support en Apple Stare Tools Mac 0S 3 GH Microsoft MacTopia Office for Macintosh GH MSN dil 3 The Getting Started screen will be displayed You may now begin your Account Setup Refer to section 7 of this User Guide to configure your Westell VersaLink for Internet connection E Welcome Microsoft Internet Explorer O x Getting Started Welcome to the Westel Setup wizard The following screens will ask you a few simple set up questions that you will need to answer to establish a connection profile Click next to start 030 300500 Rev A 30 October 2006 WESTELL User Guide VersaLink Gateway Model 327W The following sections explain the advanced features of VersaLink This Page Intentionally Left Blank 030 300500 Rev A 31 October 2006 Pa WESTELL User Guide VersaLink Gateway Model 327W 9 SETTING UP ADVANCED CONFIGURATION Advanced Configuration instructions are explained in Section 10 through Section 16 If you want to set up advanced features for VersaLink follow the instructions provided in sections 10 through IMPORTANT The following sections assume that you have active DSL and Internet service VersaLink allows you to make changes to advanced features of your Gateway such as account profiles routing configurations and firewall settings The following sections explain each feature and show you how to make changes to VersaLink s settings A menu is displayed at the top o
19. Fragment Size 244 D e e Factory Default DISABLED If this box is checked Quality of Service QOS will be Enabled Factory Default DISABLED If this box is checked Turbo TCP will be Enabled QOS Configuration QOS Filter Enable Factory Default DISABLED If this box is checked this will Enable the QOS filter QOS Classification This feature provides the capability to partition network traffic into multiple priority levels or classes of service After packet classification other QoS features can be utilized to assign the appropriate traffic handling policies including congestion management bandwidth allocation and delay bounds for each traffic class 030 300500 Rev A 109 October 2006 Pa WESTELL User Guide VersaLink Gateway Model 327W Possible responses are Best Effort BE Assured Forwarding AF1 Assured Forwarding AF2 Assured Forwarding AF3 Assured Forwarding AF4 Expedited Forwarding EF Network Control NC Peak Information Rte The maximum allowed rate for this priority expressed as a percentage of the DSL rate Committed Information Rate The committed rate for this priority expressed as a percentage of the DSL rate Latency Boundary This configures the maximum latency boundary in milliseconds that a specific packet may be delayed by Latency Threshold ms This setting configures the maximum latency boundary in milliseconds that a specific packet may be delayed by Possible r
20. Gateway Model 327W 14 3 Administrative Password The following settings will be displayed if you select Administrative Password from the Maintenance menu After you enter your data into the appropriate settings click on change NOTE If the Gateway is password protected and you are not an authorized user you will not be able to change the values The Gateway cannot be configured unless the user is logged in Contact your network administrator for further instructions 3 Change Password Microsoft Internet Explorer File Edit View Favorites Tools Help E A a Discover Better Broadband Home Status Configuration Maintenance Troubleshooting Help Enter Administration Name Enter Administration Password verify Administration Password changes the systems administration password not the ppp password Enter Administrative Name Type the name of your network administrative NOTE This changes the Systems Administrator password not the PPP password Enter Administrative Password Type your network administrator s password Verify Administrative Password Re type your network administrator s password 030 300500 Rev A 126 October 2006 a WESTELL User Guide VersaLink Gateway Model 327W 14 4 Remote Access The following screen will appear if you select Remote Access from the Maintenance menu To enable Remote Access type in a password and click the enable remote access button NOTE The password should
21. Guide VersaLink Gateway Model 327W 8 SETTING UP MACINTOSH OS X This section provides instructions on how to use Macintosh Operating System 10 with VersaLink Follow the instructions in this section to create a new network configuration for Macintosh OS X NOTE Macintosh computers must use VersaLink s Ethernet installation Refer to section 6 INSTALLING THE HARDWARE Open the System Preference Screen After you have connected the Westell VersaLink to the Ethernet port of your Macintosh the screen below will appear Click on the Apple icon in the upper right corner of the screen and select System Preferences F E Grab File Edit Captu About This Mac Get Mac 05 X Software System Preferences Dock Location Recent Items Force Quit Sleep Restart Shut Down Log Out Choose the Network Preferences After selecting System Preferences from the previous screen the System Preferences screen will be displayed From the System Preferences screen click on the Network icon System Preferences H d e A CG Show All Displays Sound Drag your favorite preferences to the toolbar abov OR rl bal 5 EK 030 300500 Rev A 27 October 2006 WESTELL User Guide VersaLink Gateway Model 327W Create a New Location After selecting the Network icon at the System Preferences screen the Network screen will be displayed Select New Location from the
22. NOTE If the IP or PPP session is dropped due to an idle timeout the light will remain solid green if an ADSL connection is still present If the session is dropped for any other reason the light is turned OFF The light will turn red when it attempts to reconnect and DHCP or PPP fails Device attempted to become IP connected and failed no DHCP Solid Red response no PPP response PPP authentication failed no IP address from IPCP etc Modem power is OFF Modem is in Bridge Mode or the connection 1s not present NOTE Safe Boot is reflected when the Power and Internet LEDs are both Red and all other LEDs are off Flashing Green INTERNET 030 300500 Rev A 9 October 2006 Pe WESTELL User Guide VersaLink Gateway Model 327W 5 2 Cable Connectors and Switch Locations e DSL connector RJ 11 e Reser button e 4 Ethernet connector RJ 45 with optional uplink port NOTE When using the optional uplink port E1 Ethernet LAN connection is limited to E2 E3 and E4 e Power connector barrel e ON OFF Switch e Wireless IEEE 802 11b g SMA connector and antenna NOTE When using the optional uplink port E1 Ethernet LAN connection is limited to E2 E3 and E4 The UPLINK feature is optional If UPLINK is not enabled VersaLink will use DSL and wireless only leTmeRNeT e np pn du E O DSL RESET DC 12V POWER e DSL Line Reset Ethernet Connectors Power ON OFF Wireless Antenna Connector Butto
23. ServerName to the IP assigned to VersaLink from your ISP USENET News Service 143 TCP VNC Virtual Network Computing 5500 TCP 5800 TCP 5900 TCP Westwood Online C amp C 4000 TCP UDP 1140 1234 TCP UDP World Wide Web HTTP 80 TCP 443 TCP SSL 8008 OR 8080 TCP PROXY XBOX Live TCP UDP 88 and 3074 Yahoo Messenger Chat 5000 5001 TCP Yahoo Messenger Phone 5055 UDP IPSec Encryption IPSec using AH can not be supported through NAT IPSec using ESP and L2TP can be supported via an ALG ZER IPSec using ESP and L2TP can be supported via an ALG PPTP Works through NAT 030 300500 Rev A 153 October 2006 a WESTELL User Guide VersaLink Gateway Model 327W 17 TECHNICAL SUPPORT INFORMATION Westell Technical Support If technical assistance is required contact Westell by using one of the following options North America U K Europe Phone 1 630 375 4900 Phone 44 01256 843311 Visit Westell at www Westell com to view frequently asked questions and enter on line service requests or send email to global_support westell com to obtain additional information 18 WARRANTY AND REPAIRS Warranty Westell warrants this product free from defects at the time of shipment Westell also warrants this product fully functional for the period specified by the terms of the warranty Any attempt to repair or modify the equipment by anyone other than an authorized representative will void the warranty Repairs Westell wil
24. Services from the Configuration menu Next Select a NAT service from the options provided at the Service Name drop down arrow NOTE You can attach multiple NAT services to your profile However for each NAT service that you attach to your profile you must first select the new NAT service Then you must load the new NAT Configuration as explained in section 12 2 2 In the following screen the Default profile has been selected as the profile that will host the selected NAT service However you can attach a NAT service to any profile WESTELL Discover Better Broadteed Home Status Configuration Maintenance Troubleshooting Help Service Contiguration Current Profile Detault v Amence Onine Service Name gt Select A Service UPNP Enable NO 2001 b AOL Instant Messenger Aliens vs Predator Anarchy Onine Age of Empires H The Conquerors Service Name Ash 5 Host Device f your firewal the Services Fagiter Ace Il tor OX play FTP 030 300500 Rev A 52 October 2006 a WESTELL User Guide VersaLink Gateway Model 327W For example the screen below displays America Online as the NAT service selected After you have selected a service click enable a Bi Contiguration Curent Profila Dedteult Service Name Amenta Online 1 Depates Custom Service UPNP Enable Servio Name Service Mode Host Device if your firewall is enabled the firewall rules take precedence over the Ser
25. assigned to the Host Name 030 300500 Rev A 69 October 2006 User Guide VersaLink Gateway Model 327W Discover Local Devices This field displays a list of the computers on the LAN that were assigned a DHCP Address The DNS name and IP address entry of each discovered device is displayed NOTE The values in this field will be displayed barring any propagation delays If No Discovered Devices is displayed manually refresh the screen If you want to add a new Host Name and IP address to your DNS server enter VersaLink s Host Name and IP Address in the fields provided in the Static Host Assignment section ZA DNS Configuration Microsoft Internet Explorer File Edt View Favorites Tools Help Discover Better Broadband Home Status Configuration Maintenance Troubleshooting Help 3 DNS Configuration User Assigned DNS Domain Name myhome westell com Static Host Assignment Host Name IP Address dslrouter 192 168 1 1 deviceweb 192 168 1 1 SmartDevice 192 168 1 1 0 0 0 0 Discovered Local Devices No Discovered Devices 030 300500 Rev A 70 October 2006 User Guide The following screen displays a Host Name and an IP Address in the fields Now click on add t Explorer WESTELL Discover Better Broadband Home Status Configuration Maintenance Troubleshooting Help DNS Configuration User Assigned DNS Domain Name myhome westell com Static Host Assignment Host Name IP Address
26. be at least 4 characters long and should not exceed 32 characters Do not type a blank space or asterisks in the Password field The password is also case sensitive Remote Access User Name Password Tim gut DI Minutes Gisable Timecnst Ia Enable Ramote Arrc zs LI Bomotg URL hrpu 172 25 3 tee g Displays your current User Name Static field Field for entering your password URL Displays the IP address of the remote management VersaLink The following screen displays a message that the remote access is currently enabled After 20 minutes of inactivity or on reboot remote access will be automatically disabled To disable remote access click on the disable remote access button WES TELL EE Rane Here Brmz paog Home Status Configuration Maintenance Troubleshooting Help Bernie Access Remote accass is currently enabled After 20 minutes of inactivity OF on reboot remote access will bo automatically disabled Le Hamit fta ie Password CELTI Treo fa Mit bot Dez able Tout Enable Rernote Access F Bemote LPL hita 172 20 3 15656 2420 2peh 030 300500 Rev A 127 October 2006 a WESTELL User Guide VersaLink Gateway Model 327W 14 5 Update Device The following screen will be displayed if you click on Update Device from the Maintenance menu This screen is used to update the firmware that controls the operation of VersaLink The updated firmware may be loaded from either a file that is located on
27. be served from the Private LAN pool Private LAN Enable Default CHECKED If this box is CHECKED it enables the addresses from the Private LAN to use the NAT interface Modem IP Address Displays VersaLink s IP address 030 300500 Rev A 71 October 2006 Pa WESTELL User Guide VersaLink Gateway Model 327W Subnet Mask Displays the Subnet Mask which determines what portion of an IP address is controlled by the network and which portion is controlled by the host DHCP Start Address Displays the first IP address that the DHCP server will provide DHCP End Address Displays the last IP address that the DHCP server will provide DHCP Lease Time Displays the amount of time the provided addresses will be valid after which the DHCP client will usually re submit a request NOTE DHCP Lease Time value must be greater than 10 seconds The default 01 00 00 00 Seconds must be between 0 and 59 minutes must be between 0 and 59 and hours must be between 0 and 23 If the settings you have entered in the Private LAN Configuration screen are incorrect the following warnings messages may be displayed via pop up screens If this occurs check the settings in the Private LAN Configuration screen 030 300500 Rev A 78 October 2006 WESTELL User Guide VersaLink Gateway Model 327W 12 5 6 Public LAN Configuration Multiple IP Address PassThrough The following screen will be displayed if you select Public LAN from the Adv
28. oe an IP Ping of the Service Provider s VersaLink This test verifies that VersaLink can exchange IP traffic with an entity on the other side of the DSL line Possible responses are Success VersaLink has detected an IP Remote VersaLink connection No Response The IP Remote VersaLink does not answer the IP Ping Could not test The test could not be executed due to VersaLink settings Check your DSL sync or your PPP session You must have both a DSL sync and a PPP connection established to execute a PING Performs a test to try to resolve the name of a particular host The host name is entered in the input box Possible responses are Success VersaLink has successfully obtained the resolved address The IP address is shown below the host name input box No Response VersaLink has failed to obtain the resolved address 030 300500 Rev A 134 October 2006 Pe WESTELL User Guide VersaLink Gateway Model 327W Host not found The DNS Server was unable to find an address for the given host name No data enter host name No host name is specified Could not test The test could not be executed due to VersaLink settings Check your DSL sync or your PPP session You must have both a DSL sync and a PPP connection established to execute a PING PING Performs an IP connectivity check to a remote computer either within or beyond via IP Address or Host Name the Service Provider s network You can PING a remote computer via
29. profile click on Close in the New Connection screen NOTE NAT Profiles allow you to create specific service settings A NAT Profile may be associated with a certain connection setting or NAT services This allows you to customize the profile for specific users You may store up to eight unique user profiles in your Gateway Details on the New Connection screen are located at the end of this section 3 WireSpeed Dual Connect Microsoft Internet Explorer De Edit View Favorites Tools Help Discover Better Broadband Home Status Configuration Maintenance Troubleshooting Help Advanced Home EE eS New Connection Connection Name My Connection ss SSSSSSCSCi S User provided name for connection profile Account ID Provided by your ISP Account Password Provided by your ISP Service Profile Default P Manual OnDemand Always On Connection Overview C Time Out Enable M Save Password eo Minutes for Connection Time Out D ES DSL Connect Rate Down Up 8000 KBits Sec by 0992 KBits Sec Connection Name PPP Status i a i lt i sconnec edit new Connection The new connection link allows the user to add more connections ED give 7 If you clicked OK in the Save new connection pop up screen the following screen will be displayed This screen will allow you to edit a connection profile Select a profile name from the Connection Name field and click on the edit button adjacent
30. solid Green VersaLink is functioning properly 7 Check to see if VersaLink s Wireless LED is solid Green This means that the Wireless interface is functioning properly Congratulations You have completed the Wireless installation VersaLink You must now go to section 7 to configure VersaLink for Internet connection Figure 2 Connection via Wireless 030 300500 Rev A 15 October 2006 WESTELL User Guide VersaLink Gateway Model 327W 6 4 3 Installation via Ethernet and Wireless Combination The VersaLink supports simultaneous use of 10 100 Base T Ethernet and Wireless configurations The following instructions explain how to install VersaLink for simultaneous use of Ethernet and Wireless ports NOTE Refer to Figure and Figure 2 for instructions on hardware installation via Ethernet and Wireless connections 1 Ensure that an 802 11b g g wireless network adapter has been installed in each PC on your wireless network 2 Install the appropriate drivers for your Wireless EEE802 11b or IEEE802 11g adapter 3 Make sure the SMA antenna connector is loose Orient the antenna in the proper configuration Then tighten the antenna knob to lock it into place 4 Connect the power supply cord to the power connector marked DC 12V on the rear panel of VersaLink Plug the other end of the power supply into a wall socket and then turn on the modem 5 Connect the DSL phone cable from connector marked LJ on the rear panel of Ve
31. the IP address or the DNS address If your PING fails try a different IP or DNS address Possible responses are Success The Remote Host computer was detected No Response There was no response to the Ping from the remote computer No name or address to PING No host name or IP address was specified Could not test The test could not be executed due to VersaLink settings Check your DSL sync or your PPP session You must have both a DSL sync and a PPP connection established to execute a PING Determines the route taken to destination by sending Internet Control Message Protocol ICMP echo packets with varying IP Time To Live TTL values to the destination Trace Route is used to determine where the packet is stopped on the network 15 2 Diagnostic Logs If you select Diagnostic Log from the System Self Test menu the following screen will be displayed 3 Diagnostic Logs Microsoft Internet Explorer File Edit Yiew Favorites Tools Help Discover Better Broadband Home Status Configuration Maintenance Troubleshooting Help Date March 18 2004 Time 14 10 35 LOGS Select a log D Clear EISE log printable savable format Remote Logging Enable I Remote IP Address 192 168 1 47 030 300500 Rev A 135 October 2006 NW User Guide VersaLink Gateway Model 327W To see a list of the log options click on the arrow at the LOGS drop down menu Select an option from the list provided at the Diag
32. to the name 030 300500 Rev A 34 October 2006 User Guide VersaLink Gateway Model 327W 3 Application image Microsoft Internet Explorer Wu Atl e WESTELL EE Discover Better Broadband Home Status Configuration Maintenance Troubleshooting Help Advanced Home Connection Overview DSL Connect Rate Down Up 8064 KBits Sec by 1024 KBits Sec Connection Name PPP Status edit My Connection DOWN new connection The new connection link allows the user to add more connections 10 2 Editing Account Profiles If you clicked Edit in the preceding screen the Edit My Connection screen will appear Follow the steps in the Edit My Connection screen to change your existing connection profile which you set up in section 8 If you do not want to change your connection profile click on close in the screen Click on delete if you want to delete your connection profile T Appbcation Sa Mvroolt lntemet Colores Edit My Connection tn GMT EN Connection Alvari Horna Connection Name MyConnection its sSSCis User provided name for connection profile Account ID stell local Provided by your ISP Account Password ees Ve dite ge OR CW AEN Provided by your ISP Manual OnDemand Always On T Time Out Enable M Save Password Connectlon Name PPP Status e Ea ci a Ce fo Minutes for Connection Time Out Help The new connection ink alow the user to add more connections
33. 030 300500 Rev A 35 October 2006 WESTELL User Guide VersaLink Gateway Model 327W characters Account ID The account ID that you used in section 8 if you are connecting to the same Service Provider If you have multiple Service Providers you can enter this information at this time Account Password The account password that you used in section 8 if you are connecting to the same Service Provider If you have multiple Service Providers you can enter this information at this time Service Profile Westell recommends that you use the Default parameter Factory default MANUAL Selecting this feature allows you to manually establish your PPP session On Demand Selecting this feature allows the Gateway to automatically re establish your PPP session on demand anytime your PC requests Internet activity for example browsing the Internet email etc When you have traffic it may cause a delay session when you log on or if the PPP session goes down Time Out Enable Factory Default DISABLED Selecting this feature allows you to enable the timeout parameter of your PPP session which is set to a factory default of 20 minutes Selecting this feature allows you to save the password for your new connection profile in VersaLink so that you will not have to re enter it in case of a re boot Minutes for Connection Time Out This option allows you to specify the number of minutes that you want a PPP session to stay active before it is disconnect
34. 2 5 Advanced LAN This section explains the configurable features of VersaLink that are available if you select Advanced LAN from the Configuration menu NOTE If VersaLink is configured for ETHERNET PORT 1 VLAN will not be displayed You must configure VersaLink for DSLATM PORT to access VLAN in the Advanced LAN drop down menu Refer to section 12 6 2 1 for details 12 5 1 DNS Configuration The following settings will be displayed if you select DNS from the Advanced LAN menu 3 DNS Configuration Microsoft Internet Explorer File Edit View Favorites Tools Help Ae Discover Better Broadband Home Status Configuration Maintenance Troubleshooting Help DNS Configuration User Assigned DNS Domain Name myhome westell com Static Host Assignment Host Name IP Address dslrouter 192 168 1 1 deviceweb 192 168 1 1 SmartDevice 192 168 1 1 0 0 0 0 Discovered Local Devices No Discovered Devices User Assigned DNS Domain Name This field allows you to enter a Domain Name for VersaLink NOTE Some ISP s may To add a Domain Name in the field under User Assigned DNS type in your new require the name for domain name and click Set identification purposes Static Host Assignment Host Name This field allows you to enter a HOST name for VersaLink To add a new Host name in the field under Static Host Assignment type in the Host Name and the IP address and click Set IP Address Displays the IP address that is
35. 4 KBits Sec by 1024 KBits Sec Connection Name PPP Status My Connection DOWN Connect qx Profile with the is your default profile To make changes to your default profile click on the profile editor button 030 300500 Rev A 23 October 2006 M WESTELL User Guide VersaLink Gateway Model 327W 7 3 Establishing a PPP Session View the PPP Status at the Home page If the PPP Status displays DOWN click the Connect button to establish a PPP session NOTE Whenever the PPP Status displays DOWN you do not have a PPP session established If your Gateway s connection setting is set to Always On or On Demand after a brief delay the PPP session will be established automatically and the PPP Status will display UP If the connection setting is set to Manual you must click on the Connect button to establish a PPP session Once the PPP session has been established PPP Status displays UP you may proceed with your Gateway s configuration Section 10 2 provides instructions on editing the connection settings Refer to the Edit My Connection screen VersaLink s factory default connection setting is Manual If you click the Connect button the following screen will appear briefly The PPP Status in the Connection Overview window allows you to view the state of your ISP connection When the PPP Status displays Connecting this means that you are establishing a PPP session SI Application im
36. 991 2 ANSI T1 413 e Upgradeable to ADSL2 ADSL2 READSL Protocol Features e Bridge Encapsulation per RFC2684 Formerly RFC1483 Logical Link Control Subnetwork Access Protocol LLC SNAP Software Upgradeable PPPoE Support ATM SAR Internal to Modem System Requirements for 10 100 Base T Ethernet e Pentium or equivalent and above machines e Microsoft Windows 95 98 ME 2000 NT 4 0 or XP Macintosh OS X or Linux installed e Operating system CD Internet Explorer 4 x or Netscape Navigator 4 x or higher 64 MB RAM 128 MB recommended Ethernet 10 100 Base T interface 10 MB of free hard drive space TCP IP Protocol stack installed System Requirements for Wireless e Pentium or equivalent and above class machines e Microsoft Windows 98 ME 2000 or XP or Macintosh OS X installed e Operating System CD on hand 030 300500 Rev A 155 e Internet Explorer 4 x or Netscape Navigator 4 x or higher e 64 MB RAM 128 MB recommended e 10 MB of free hard drive space e IEEE 802 11b g g PC adapter LEDs e Power e Ethernet e Wireless e DSL e Internet Connectors e DSL RJ 11 6 pin modular jack DSL e Ethernet RJ 45 8 pin modular jack e Power Connector e SMA antenna Power e Power Supply External 120 VAC to 12V DC wall mount power supply e Power Consumption Less than 6 watts typical from 120 VAC Environmental e Ambient Operating Temperature 32 to 104 F 0 to 40 C e Relative Humidity 5 to 95 no
37. B RAM 128 MB recommended 10 MB of free hard drive space An available IEEE 802 1 1b g g PC adapter ETHERNET WIRELESS IEEE 802 11 030 300500 Rev A 8 October 2006 a WESTELL User Guide VersaLink Gateway Model 327W 5 HARDWARE FEATURES 5 1 LED Indicators This section explains the LED States and Descriptions LED indicators are used to verify the unit s operation and Status LED States and Descriptions Description Modem power is ON Modem power is OFF POWER POST Power On Self Test Failure not bootable or Device Solid Red Malfunction NOTE The Power LED should be red no longer than two seconds after the power on self test passes Powered device is connected to the associated port includes devices with wake on LAN capability where slight voltage is Solid Green supplied to an Ethernet connection ETHERNET NOTE When using the optional uplink port E1 Ethernet LAN E1 E2 E3 E4 connection is limited to E2 E3 and E4 Flashing Green 10 100 Base T LAN activity is present traffic in either direction FF Modem power is OFF no cable or no powered device is connected to the associated port Link Established WIRELESS Wireless LAN activity is present traffic in either direction Modem power is OFF or No Link Good DSL syne DSL DSL attempting to sync Modem power is OFF Internet link established IP connection established and IP Traffic is passing through device in either direction
38. C Filter from the Configuration menu To enable MAC Address filtering click the box adjacent to Enable MAC Address Filtering A check mark will appear in the box Next click save to save the setting To add or edit a MAC Address setting click the add button Wirth MAC Address Filter Table Enable MAC Address Fatenng save When the MAC Address Filter is enabled only the stathons that are in this table and eet to Allowed will he accapted All others will be blocked Currently the MAC Address table is empty If you click add in the preceding screen the following screen will be displayed Enter the appropriate values for your MAC Address settings and then click save to save the settings Click cancel if you wish to return to the preceding screen E HAC Information Microsoft Internet Explorer x MAC Address Settings Traffic Allowed MAC Address 00 00 00 00 00 00 Station Name 030 300500 Rev A 66 October 2006 WESTELL User Guide VersaLink Gateway Model 327W Traffic Allowed When the MAC Filter is enabled only stations in the MAC Filter Table which are set to Allowed will have access to the AP Blocked This allows the station to remain in the table but no access to the VersaLink is allowed MAC Address The MAC address assigned to the station that you want to allow access to Station Name The station name or description that the MAC address is assigned to This is an optional field t
39. DOWN This means that you no longer have a PPP session no IP connection to your Internet service provider However your DSL session will not be affected When you are ready to end your DSL session simply power down VersaLink via the power switch on VersaLink s rear panel Z Application image Microsoft Internet Explorer File Edit View Favorites Tools Help SH Discover Better Broadband Home Status Configuration Maintenance Troubleshooting Help Connection Overview Connection Name PPP Status o My Connection DOWN Connect enki Profile with the Is your default profile To make changes to your default profile click on the profile editor button When you are ready to establish a PPP session click on the connect button If you powered down VersaLink you must first power up VersaLink and log on to your account profile before you establish a PPP session NOTE When you are ready to exit VersaLink s interface click on the X close in the upper right corner of the window Closing the window will not affect your PPP Status your PPP session will not be disconnected You must click on the disconnect button to disconnect your PPP session When you are ready to restore this interface you must launch your Internet browser and type http dslrouter or type http 192 168 1 1 in the browser s address window and press Enter on your keyboard 030 300500 Rev A 26 October 2006 M WESTELL User
40. E After a brief delay the home page will be displayed Confirm that you have a DSL sync and that your PPP session displays UP Click on the connect button to establish a PPP session 030 300500 Rev A 89 October 2006 a WESTELL User Guide VersaLink Gateway Model 327W 12 6 2 2 Disabling DSLATM PORT Enabling ETHERNET PORT 1 To configure the VersaLink so that it uses the WAN Ethernet Port select ETHERNET PORT 1 from the WAN PORT drop down arrow By selecting ETHERNET PORT 1 you will disable the VersaLink s DSL transceiver This will disable the DSL Port and allow the WAN interface to use the WAN Ethernet Port NOTE If ETHERNET PORT 1 is configured the VersaLink s menu options may or may not be displayed The sections explained throughout this document will indicate when a menu item is unavailable The UPLINK feature is optional and if UPLINK is not enabled in the ini file the Gateway will use DSL and Wireless only ki WAN Configuration Microsoft Internet Explorer File Edit View Favorites Tools Help WAN PORT DSLATM PORT D Status ETHERNET PORTI Enable D 36 PPPoE Disable zl 43 Bridge Disable zl 37 Bridge Disable zl 38 Bridge Disable 39 Bridge Disable 40 Bridge Disable zl 41 Bridge Bridge Broadcast Iv Bridge Multicast I Spanning Tree Protocol Save filter settings NOTE If you experience any problems please reset VersaLink via the external hardware reset button or via the p
41. Gateway Model 327W 12 6 4 Configuring VersaLink s Protocol Settings for PPPoE Mode To configure VersaLink s protocol settings for PPPoE mode select WAN from the Advanced WAN menu The WAN Configuration screen will be displayed Next click on the edit button adjacent to any of the existing Enabled VC Virtual Connection protocols NOTE The protocol status must display Enable to allow edits to its VC configuration 23 WAN Configuration Microsoft Internet Explorer Fi e e Discover Better Broadband Home Status Configuration Maintenance Troubleshooting Help A WAN PORT DSLATM PORT v Status YPI YCI Protocol Enable D 0 36 PPPOE ed t Disable 9 43 Bridge T Disable zl 9 37 Bridge S Disable 9 38 Bridge Disable 9 39 Bridge Disable 9 40 Bridge Disable 0 41 Bridge Bridge Broadcast M Bridge Multicast Iv Spanning Tree Protocol l Save filter settings 030 300500 Rev A 95 October 2006 WESTELL User Guide VersaLink Gateway Model 327W If you clicked edit in the WAN Configuration screen the following VC 1 Configuration screen will be displayed Select PPPoE from the options listed in Protocol drop down arrow After you have made the configuration for this protocol select the set VC button aq C 1 Configuration Microsoft Internet Explorer File Edt Yiew Favortes Tools Help VC 1 Configuration vrb vas perho Qos UBR sl Protocol PPPoE R Status PPPOA o VC 1
42. Gateway Model 327W 12 6 9 RIP The following details will be displayed if you select RIP from the Advanced WAN menu If you change any settings in this screen click on save If you click on reset this screen will refresh and display your last saved RIP configuration RIP Routing Interface Protocol is a dynamic inter network routing protocol primarily used in interior routing environments A dynamic routing protocol as opposed to a static routing protocol automatically discovers routes and builds routing tables ae WESTELL SS SSE ESS Discover Better Broadband Home Status Configuration Maintenance Troubleshooting Help RIP Enable r RIP Configuration Interface Type Receive Transmit RIPv2 Authentication Mode Advanced Default Gateway Border Gateway Filtering RIP Timer Rate RIP Supply Interval RIP Expire Time RIP Garbage Collection Time NOTE In this screen VersaLink represents Gateway 030 300500 Rev A 113 October 2006 a WESTELL User Guide VersaLink Gateway Model 327W RIP Enable Factory Default DISABLED If this box is checked RIP will be Enabled turned ON RIP Configuration LAN Select this if you are configuring RIP for the LAN side Interface Type WAN Select this if you are configuring RIP for the WAN side WAN side is receive only Receive The version of RIP to be accepted Possible responses are None RIPv1 RIPv2 RIPv1 or RIPv2 Transmit The version of RIP to
43. Help j Single Static IP Configuration Please select which device will share your Single Static IP if User Configured PC is selected 2 local PC must be manually configured to have the Single Static iP address WAN IP Address 172 24 48 4 Single Static IP is currently disabled If you select a device and clicked on enable the following pop up screen will appear Click on OK to enable this device for Single Static IP Click on Cancel if you do not want to enable Single Static IP NOTE The actual device name may differ from the name displayed in this screen Microsoft Internet Explorer Enable IP Passthrough for salle 9827 Cancel 030 300500 Rev A 40 October 2006 Ww WESTELL User Guide VersaLink Gateway Model 327W If you clicked OK in the preceding pop up screen the following pop up screen will appear VersaLink must be reset to allow the new configuration to take effect Click on OK Microsoft Internet Explorer NI K The modem must be reset in order for the new configuration to take affect Do pou wish to reset now If you clicked OK in the preceding screen the following screen will be displayed VersaLink will be reset and the new configuration will take effect File Edit View Favorites Tools Help e SI Links sl WEE Discover Better Broadband Home Status Configuration Maintenance Troubleshooting Help d Resetting Modem Please Wait The modem is resetting in ord
44. IP as this Services description address on the LAN only after Local Trigger Dp DR specific outbound traffic Port Range d D Global Port Gu sg PE When outbound traffic is detected on the Frigger Port Fort Forwarding is enabled through the Range of the Global Farts back cancel The NAT service you selected Local Trigger Port Range The local LAN side TCP UDP port Global Port Range The WAN side TCP UDP port range 030 300500 Rev A 117 October 2006 Pe WESTELL User Guide VersaLink Gateway Model 327W 13 4 Adding Local Trigger Ports If you made changes in the Local Trigger Port Range screen and clicked next the following screen will be displayed Click on close to accept the changes or click on add to go back to the Trigger Ports screen and enter additional port range values You can repeat this step for each port range that you want to add up to 10 trigger ports When you are finished adding ports to the Local Trigger Port Range you must click on close to accept the information you have entered and to return to the Service Configuration screen S Service Details Microsoft Internet Explorer Service Details Service Name Custom Trigger Port Type Trigger Ports Port 1 Protocol TCP UDP Global Port si 1 12 Trigger Port s 1 12 After clicking Close you can enable your new service from the Senice Mare select box close 030 300500 Rev A 118 October 2006 Pe WESTELL
45. Internet Service Provider ISP Refer to the Internet service provider s installation manual to install the software required for your Internet connection NOTE Internet service provider subscriber software and connection requirements may vary Consult your Internet service provider for installation instructions 7 1 Setting Up an Account Profile After connecting VersaLink bring up your Web browser and type either http dslrouter or http 192 168 1 1 in the browser s address window and then press Enter on your keyboard The Getting Started screen will appear Click on next e Welcome Microsoft Internet Explorer Oy x Getting Started Welcome to the Westell Setup wizard The following screens will ask you afew simple set up questions that you will need to answer to establish a connection profile Click next to start m 030 300500 Rev A 17 October 2006 Pe WESTELL User Guide VersaLink Gateway Model 327W If you clicked Next the following screen will be displayed This screen will allow you to set up your account profile NOTE Before you set up your account profile you must obtain your Account ID Account Password and VPI VCI values from your Internet service provider You will use this information when you set up your account parameters If you are at a screen and need help click on the Help button to learn more about the screen User Name Connection Name ha Connection User
46. Ir bim html Lancel Encoding Western European I d mdowsl 030 300500 Rev A 138 October 2006 WESTELL User Guide VersaLink Gateway Model 327W 15 3 Statistics NOTE If VersaLink is configured for ETHERNET PORT 1 only Ethernet and Wireless statistics will be displayed in the Statistics menu The DSL Transceiver statistics and the WAN VC statistics will not be displayed If you want to view DSL Transceiver and WAN VC statistics you must configure VersaLink for DSLATM PORT Refer to section 12 6 2 1 for additional details Discover Better Broadband Home Status Configuration Maintenance Troubleshooting Help System Self Tests Diagnostic Logs Statistics Status Ethernet DSL Transceiver WAN YC Connection Overview Wireless 15 3 1 Ethernet Port Statistics The following settings will be displayed if you select Ethernet from the Statistics menu Z Ethernet Port Statistics Microsoft Internet Explorer File Edit View Favorites Tools Help At Discover Better Broadband Home Status Configuration Maintenance Troubleshooting Help Ethernet Port Statistics Packet Information Port 2 In Errors In Discard Packets In Non Unicast Packets In Unicast Packets In Octets Out Errors Out Discard Packets Out Non Unicast Packets Out Unicast Packets Out Octets MTU 1600 1600 1600 1600 Interface Type 6 7 8 9 Interface Description EtherPort1 EtherPort2 EtherPort3 EtherPort4 The number of error pac
47. Iv Spanning Tree Protocol J Gui If you select DSLATM PORT from the WAN Port drop down arrow the following screen will be displayed Click OK Microsoft Internet Explorer Ea AN This change will disable your WAN ethernet port The WAN interface will use the OSL port 030 300500 Rev A 88 October 2006 Ww WESTELL User Guide VersaLink Gateway Model 327W If you click OK in the preceding pop up screen the following screen will be displayed Click on OK If you click on Cancel the change will not take effect Microsoft Internet Explorer E4 2 Are pou sure you wish to change your WAN port and enable CSL Cancel If you clicked on OK in the preceding pop up screen the following pop up screen will appear VersaLink must be reset to allow the new configuration to take effect Click on OK Microsoft Internet Explorer EJ The modem must be reset in order for the new configuration to take affect Do pou with to reset now If you clicked on OK in the preceding screen the following screen will be displayed VersaLink will be reset and the new configuration will take effect File Edt View Favorites Tools Help poe Links addess E WESTELL Discover Better Broadband Home Status Configuration Maintenance Troubleshooting Help Resetting Modem Please Wait The modem is resetting in order for the requested changes to take effect Your page will be reloaded shortly ha E
48. LL User Guide VersaLink Gateway Model 327W Indicates the DiffServ Queue Possible responses are 0 Best Effort BE 1 Assured Forwarding 1 AF1 2 Assured Forwarding 2 AF2 3 Assured Forwarding 2 AF3 4 Assured Forwarding 2 AF4 5 Expedited Forwarding EF 6 Routing Protocols DiffServ priorities 6 and 7 Max Queue Size The maximum number of packets that can be queued for this priority lack of buffer space or filtering rules Total Enqueued Packets Current Depth Deepest Depth Displays the most number of packets that have been queued at once for this priority Queue Number Peak Info Rate The maximum allowed rate for this priority expressed as a percentage of the DSL rate Committed Info Rate The committed rate for this priority expressed as a percentage of the DSL rate Peak Burst ms Displays the interval in milliseconds for averaging the peak offered rate Committed Burst ms Displays the interval in milliseconds for averaging the committed offered rate Total Packets Received Displays the total number of packets of this priority that are destined for the LAN Total Marked Packets Displays the number of packets of this priority that exceeded the committed rate but not the peak rate and were marked with a higher drop priority Total Filter Packet Drops Displays the number of packets of this priority that exceeded the peak rate and that were therefore dropped Avg DSL Bytes Per Pack
49. Location field Network i LA oz a amp 4 SC Show All Displays Sound Startup Disk Network Location Automatic Configure Internal Modem New Location Edit Location Name the New Location After selecting New Location from the Network screen the following screen will be displayed In the field labeled Name your new location change the text from Untitled to Westell Click OK Name your new location Westell All users of this computer will be able to choose this location in the Apple menu without entering a password f Cancel A TI OK Y ell ene 030 300500 Rev A 28 October 2006 Ww WESTELL User Guide VersaLink Gateway Model 327W Select the Ethernet Configuration After clicking on OK in the preceding screen the Network screen will be displayed The Network screen shows the settings for the newly created location From the Configure field in the Network screen select Built in Ethernet Click on Save NOTE Default settings for the Built in Ethernet configuration are sufficient to operate VersaLink 8 9 Network Lal A Rute amp 3 z va X gt Show All Displays Sound Startup Disk Network Location Westell ei Configure Internal Modem e Built in Ethernet a oxies Modem SS Advanced SE Configure Using PPP ei Check the IP Connection To verify that the computer is communicating with VersaLink follow the instructions below
50. Model 327W If you click on the settings button in the Update Device screen the following screen will appear This screen displays the location of the software update file Auto Update Device Microsoft Internet Explorer De Edit View Favorites Tools Help At WESTELL Discover Better Broadband Auto Update Device Home Status Configuration Maintenance Troubleshooting Help Auto Update Device Update File Location htto Awww westell com upgrades model32 W A99 32 V 1 0 00 xml 030 300500 Rev A 129 October 2006 Ww WESTELL User Guide VersaLink Gateway Model 327W Click on the local update now button in the Update Device screen to select the upgrade file from your PC s hard drive This screen allows you to upgrade the software on VersaLink Click Browse and go to the location where the upgrade file is stored E Application image Upgrade Software Microsoft Internet Explorer Software Upgrade Click browse to select the upgrade file Then start the transfer by clicking the upioad file button Upgrade File Browse Look in E pdate Software E Til cl NOTE The actual information displayed in this screen may vary Filename peroxa oo Files of type fan Files fi sl Cancel ME Select the appropriate upgrade file from your browser The file name will appear in the field labeled Upgrade File Click on upload file SI WireSpeed Dual Connect Upgrade Software Microsoft In
51. OR A PARTICULAR PURPOSE 6 Limitation of Liability Licensor s cumulative liability to you or any other party for any loss or damages resulting from any claims demands or actions arising out of or relating to this Agreement shall not exceed the license fee paid to Licensor for the use of the SOFTWARE In no event shall Licensor be liable for any indirect incidental consequential special or exemplary damages or lost profits even if Licensor has been advised of the possibility of such damages SOME STATES DO NOT ALLOW THE LIMITATION OR EXCLUSION OF LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU 7 Governing Law This License Agreement shall be construed and governed in accordance with the laws of the State of Illinois You submit to the jurisdiction of the state and federal courts of the state of Illinois and agree that venue is proper in those courts with regard to any litigation arising under this Agreement 8 Costs of Litigation If any action is brought by either party to this License Agreement against the other party regarding the subject matter hereof the prevailing party shall be entitled to recover in addition to any other relief granted reasonable attorney fees and expenses of litigation 9 Severability Should any term of this License Agreement be declared void or unenforceable by any court of competent jurisdiction such declaration shall have no effect on the remainin
52. OS with VLAN tagging HotSpot Simultaneous public private network support Hereafter the Westell VersaLink Gateway will be referred to as VersaLink or Gateway 2 SAFETY INSTRUCTIONS Never install any telephone wiring during a lightning storm Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations Never touch non insulated telephone wires or terminals unless the telephone line has been disconnected at the network interface Use caution when installing or modifying telephone lines AA warning Zi Risk of electric shock Voltages up to 140 Vdc with reference to ground may be present on telecommunications circuits 030 300500 Rev A 4 October 2006 Pa WESTELL User Guide VersaLink Gateway Model 327W 3 REGULATORY INFORMATION 3 1 FCC Compliance Note FCC ID CH8 327WXX 6 This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the Federal Communication Commission FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this eq
53. P Server drop down arrow l e DHCP Configuration Microsoft Internet Explorer Eie Edit View Favorites Tools Help WESTELL Discover Better Broadband DHCP Configuration DHCP Server Private LAN x Private HCH Settings DHCP Start Address fi 92 168 1 15 DHCP End Address fi92 168 1 47 DHCP Lease Time fi fo fo fo Days Hours Minutes Seconds ZA DHCP Configuration Microsoft Internet Explorer De Edit View Favorites Tools Help At WESTELL EE Discover Better Broadband Home Status Configuration Maintenance Troubleshooting Help J DHCP Configuration DHCP Server or D 030 300500 Rev A 75 October 2006 WESTELL User Guide VersaLink Gateway Model 327W If you selected Private LAN the following screen will be displayed automatically Click on save to save your DHCP Server setting If you click on reset your DHCP Server will be reset to factory default Private LAN is the factory default for the DHCP Server el DHCP Configuration Microsoft Internet Explorer File Edit View Favorites Tools Help WES TELL e Discover Better Broadband Home Status Configuration Maintenance Troubleshooting Help DHCP Configuration DHCP Server Private LAN D Private LAN DHCP Settings DHCP Start Address 192 168 1 15 DHCP End Address 192 168 1 47 DHCP Lease Time fi fo i lo 0 Days Hours Minutes Seconds If you clicked on save the following pop up screen will appear Click on OK Microsoft Internet Explore
54. P Server on VersaLink e Public LAN Configuration Microsoft Internet Explorer I File Edit View Favorites Tools Help Discover Better Broadband Home Status Configuration Maintenance Troubleshooting Help Public LAN Configuration Public LAN DHCP Server Enable WM Public LAN Enable C Public LAN IP Address 192 168 21 Public LAN Subnet Mask 255 255 255 0 Public LAN DHCP Settings DHCP Start Address 192 168 2 15 DHCP End Address 192 168 2215 DHCP Lease Time hh hh fo Days Hours Minutes Seconds 030 300500 Rev A 80 October 2006 Pe WESTELL User Guide VersaLink Gateway Model 327W If you clicked the Public LAN Enable box the following screen will be displayed showing the Public LAN Enable box selected Click on save 3 Public LAN Configuration Microsoft Internet Explorer File Edit View Favorites Tools Help fica WE T SE rou Discover Setter Broadband Home Status Configuration Maintenance bleshooting Help Public LAN Configuration Public LAN DHCP Server Enable Public LAN Enable Public LAN IP Address 92168 21 Public LAN Subnet Mask 255 255 255 0 Public LAN DHCP Settings DHCP Start Address 192 168 2 15 DHCP End Address 192 168 2 215 DHCP Lease Time fi b i D fo Days Hours Minutes Seconds Gam a If you selected Public LAN Enable or if you made other changes in the Public LAN Configuration screen and clicked save the following pop up screen will be di
55. PPPS IP Address Classical IPoA Gateway 0 0 0 0 ONS Primary 0 0 0 0 DNS Secondary 0 0 0 0 MPU Negotiation D LCP Echo Disable D LEP Echo Failures e Must De between 1 and 30 inctuisiyve LCP Echo Duration feo Must be between 5 and 300 seconds inchisive and greater or egual ta Retry Duration ee ee ee R E d Done PTS Internet g If you click the set VC button the following pop up screen will be displayed Click on OK in the pop up screen If you click on Cancel the new settings will not be saved After you click on OK follow the instructions to reset the Gateway as previously discussed in section 12 6 3 Microsoft Internet Explorer x Domm o See S Set this PPPoE VC configuration i Cancel 030 300500 Rev A 96 October 2006 Pe WESTELL User Guide VersaLink Gateway Model 327W 12 6 5 Configuring VersaLink s Protocol Settings for Bridge Mode To configure VersaLink s protocol settings for Bridge mode select WAN from the Advanced WAN menu The WAN Configuration screen will be displayed Next click on the edit button adjacent to any of the existing Enabled VC Virtual Connection protocols The VC1 Configuration screen will be displayed NOTE The protocol status must display Enable to allow edits to its VC configuration If you select Bridge protocol from the Protocol drop down arrow the following screen will be displayed Select a mode from the options listed
56. S shell you are susceptible to firewall rules as this PING is dependent on VersaLink s firewall settings If your firewall is set to Medium or High you will not be able to PING You must set your firewall security setting to Low or None Po onnection Status e VersaLink checks the status of the DSL connection Possible responses are UP VersaLink is operating correctly and has obtained synchronization with the opposing network device DOWN VersaLink is operating correctly but has not synchronized with the opposing device PPPoE Indicates that a PPPoE session is or is not established Possible responses are Session UP A valid PPPoE session has been detected No Session Currently there is no active PPPoE session established Initiating Session A PPP session must be connected from the homepage screen Indicates that a PPPoE or PPPoA session must already be established Possible responses are Connection UP VersaLink has established a connection No Connection There is no PPP connection Initiating Connection The PPP connection process has been initiated Connection Halted A successful PPP connection was halted Cannot Connect A PPP connection could not be made because of a PPPoE session failure Authorization Failure The user name or password is incorrect Link Control Protocol Failed Re establish the session from the home page Test Descri i tion Test Results Self Test S PING ISP s VersaLink Performs an IP network check
57. Secondary 0 0 0 0 MEJ Negotiation D LCP Echo Disable M LCF Echo Failures b iust De between i and 30 inclusive LCF Echo Duration Ip ust De between 5 and 300 seconds inclusive and greater or equal to Retry Duration LCP Echo Retry Duration DU ust be between 5 and 300 seconds inchusive Tunneling Enable Disable cancel 030 300500 Rev A 92 October 2006 a WESTELL User Guide VersaLink Gateway Model 327W VC 1 Configuration This setting allows you to change your VPI Virtual Path Indicator value for a particular VC which is defined by your Service Provider This setting allows you to change your VCI Virtual Channel Indicator value for a particular VC which is defined by your Service Provider PCR Factory Default 100 Peak Cell Rate PCR The maximum rate at which cells can be transmitted across a virtual circuit specified in cells per second and defined by the interval between the transmission of the last bit of one cell and the first bit of the next This value is a percentage of the current data rate 100 allows this VC to use 100 of the available bandwidth 80 allows this VC to use 80 of the available bandwidth Quality of Service which is determined by your Service Provider Possible Responses CBR Constant Bit Rate UBR Unspecified Bit Rate VBR Variable Bit Rate Protocol The Protocol for each VC which is specified by your Service Provider Possible Responses PPP
58. Single Static IP is disabled as shown in the following screen 030 300500 Rev A 43 October 2006 Ww WESTELL User Guide VersaLink Gateway Model 327W Ki Single Static IP lt br gt Configuration Microsoft Internet Explorer File Edit View Favorites Tools Help At WESTELL SS Discover Better Broadband Home Status Configuration Maintenance Troubleshooting Help Single Static IP Configuration Please select which device will share your Single Static IP if User Configured PC is selected 2 local PC must be manually configured to have the Single Static IP address WAN IP Address 172 24 48 4 User Configured PC salle 982 Single Static IP is currently disabled IMPORTANT After you disable Single Static IP you must reboot your computer 12 2 Service Configuration The following settings will be displayed if you select Services from the Configuration menu Westell has developed an extensive list of NAT services and you may select any service from this list By selecting your specific NAT service and setting up a NAT profile you will ensure that the appropriate ports on VersaLink are open and that the required application traffic can pass through your LAN For a list of supported services go to section 16 NAT Services NAT Profiles allow you to create specific service settings The NAT profile may then be associated with a connection profile allowing you to customize profiles for specific users For ex
59. T in packets IP Network Address PPP An IP address identifies your device on the Internet Primary DNS Provided by your Service Provider Secondary DNS Provided by your Service Provider 030 300500 Rev A 37 October 2006 Pe WESTELL User Guide VersaLink Gateway Model 327W Ethernet Status This field will display your Ethernet information that was received IN or sent OUT in packets on your Ethernet port Firewall Status This field will display your firewall traffic in packets Passed Monitors information traffic that was successfully received IN or transmitted OUT in packets Dropped Monitors information traffic that was not successfully received IN or transmitted OUT due to your firewall settings PPP Connection Information This is from the connection profile that you established in section 8 This field will display how long your PPP session has been connected Status This field will display the status of your PPP session UP Connected DOWN Disconnected Number of Reconnects This field will display the number of attempts that were made to establish a PPP session 11 2 About The following settings will be displayed if you select About from the Status menu Z About Microsoft Internet Explorer I Fie Edit View Favorites Tools Help i At Discover Better Broadband Home Status Configuration Maintenance Troubleshooting Help NOTE The actual values may differ from the values displayed i
60. TCP 5190 TCP ICUII Client 2000 2038 TCP 2050 2051 TCP 2069 TCP 2085 TCP 3010 3030 TCP ICUII Client Version 4 xx 1024 5000 TCP 2050 2051 TCP 2069 TCP 2085 TCP 3010 3030 TCP 2000 2038 TCP6700 6702 TCP 6880 TCP 1200 16090 TCP IMAP 119 TCP UDP IMAP v 3 220 TCP UDP IPSEC ESP PROTOCOL 50 IPSEC IKE 500 UDP KALI Doom amp Doom II 2213 UDP 6666 UDP EACH PC USING KALI MUST USE A DIFFERENT PORT NUMBER STARTING WITH 2213 1 KaZaa 1214 1214 TCP UDP e DP Medal Of Honor Allied Assault TCP 80 UDP 53 UDP 2093 UDP 12201 TCP 12300 UDP 2135 UDP 2139 TCP UDP 28900 mIRC Chat 6660 6669 TCP 030 300500 Rev A 151 October 2006 a WESTELL User Guide VersaLink Gateway Model 327W Application Game Port Protocol Motorhead Server 16000 TCP UDP 16010 16030 TCP UDP MSN Game Zone 6667 TCP 28800 29000 TCP MSN Game Zone DX 7 amp 8 play 6667 TCP 6073 TCP 28800 29000 TCP 47624 TCP 2300 2400 TCP UDP MSN Messenger n MaN Messenger 6891 6900 6891 6900 TCP 1863 TCP UDP 5190 UDP 6901 TCP UDP si 1863 TCP UDP 5190 UDP 6901 TCP UDP Need for Speed 3 Hot Pursuit 1030 TCP Need for Speed Porsche 9442 UDP Net2Phone 6801 UDP NNTP 119 TCP UDP Operation FlashPoint 47624 UDP 6073 UDP 2300 2400 TCP UDP 2234 TCP 5310 TCP UDP Pal Talk 2090 2091 TCP UDP 2095 TCP 5001 TCP 8200 8700 TCP UDP 1025 2500 UDP pcAnywhere host host 5631 5631 TCP 5632 UDP 22 UDP e 5632 UDP 22 UDP eh TCP UDP 9900 9901 UDP
61. User Guide VersaLink Gateway Model 327W 12 5 7 VLAN The following settings will be displayed if you select VLAN from the Advanced LAN menu ZA Y LAN Configuration Microsoft Internet Explorer File Edit View Favorites Tools Help Discover Better Broadband Home Status Configuration Maintenance Troubleshooting Help LAN Enable E YLAN Configuration LAN Port Ethernet Port D YLAN ID D YLAN Priority ER Outgoing YLAN Tag REMOVE D GC VLAN Enable Factory Default DISABLED If this box is check VLAN will be Enabled This will allow VLAN tagging to occur according to the data port s configuration LAN Port This allows you to select the LAN port that you wish to configure Possible responses are Ethernet Port 1 Ethernet Port 2 Ethernet Port 3 Ethernet Port 4 WLAN Port VLAN ID This allows you to assign a VLAN ID to the port Possible responses are 1 through 8 VLAN Priority This allows you to set the VLAN priority for the port Possible responses are O through 7 outgoing 030 300500 Rev A 83 October 2006 WESTELL User Guide VersaLink Gateway Model 327W To enable VLAN click on the box adjacent to the VLAN Enable field A check mark will appear in the box Click on save NOTE For VLAN to function properly the VLAN ID must be set to a value other than 1 in VLAN Configuration screen and in the VC 1 Configuration screen when the you are using the Bridge VLAN Bridge protoc
62. age Microsoft Internet Explorer File Edit View Favorites Tools Help Discover Better Broadband Home Status Configuration Maintenance Troubleshooting Help Home Connection Overview DSL Connect Rate Down Up 8064 KBits Sec by 1024 KBits Sec Connection Name PPP Status My Connection Connecting RECHT T GED Profile with the is your default profile To make changes to your default profile click on the profile editor button 030 300500 Rev A 24 October 2006 M User Guide VersaLink Gateway Model 327W After a PPP session has been established the PPP Status will display UP Congratulations You may now browse the Internet amp Application image Microsoft Internet Explorer Ele Edit View Favorites Tools Help Discover Better Broadband Home Status Configuration Maintenance Troubleshooting Help Connection Overview DSL Connect Rate Down Up 8064 KBits Sec by 1024 kKBits Sec Connection Name PPP Status My Connection UP disconnect profile editor Profile with the Is your default profile To make changes to your default profile click on the profile editor button For example if you want to visit Westell s home page type http www westell com in your browser s address window e Westell com Microsoft Internet Explorer File Edit View Favorites Tools Help Address SI http www westell com pages index jsp At WESTELL Discover Better Broad
63. alified installer This equipment cannot be used on public coin phone service provided by the telephone company Connection of this equipment to party line service is subject to state tariffs 3 2 Canada Certification Notice The Industry Canada label identifies certified equipment This certification means that the equipment meets certain telecommunications network protective operations and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document s The department does not guarantee the equipment will operate to the user s satisfaction This equipment meets the applicable Industry Canada Terminal Equipment Technical Specification This 1s confirmed by the registration number The abbreviation IC before the registration number signifies that registration was performed based on a Declaration of Conformity indicating that Industry Canada technical specification were met It does not imply that Industry Canada approved the equipment The Ringer Equivalence Number REN is 0 0 The Ringer Equivalence Number that is assigned to each piece of terminal equipment provides an indication of the maximum number of terminals allowed to be connected to a telephone interface The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed five Before installing this equipment users should e
64. allow the modem to be reset and the new configuration will take effect Click on OK Microsoft Internet Explorer E an D D D P The modem must be reset in order for the new configuration to take affect Do pou wish to reset now If you clicked on OK in the preceding screen the following screen will be displayed VersaLink will be reset and the new configuration will take effect Fie Edit Yiew Favorites Tools Help e gt toe Cep iscov ver Setter Broadband Home Status Configuration Maintenance Troubleshooting Help Resetting Modem Please Wait The modem is resetting in order for the requested changes to take effect Your page will be reloaded shortly Internet After a brief delay the home page will be displayed Confirm that you have a DSL sync and that your PPP session displays UP Click on the connect button to establish a PPP session NOTE Whenever the PPP Status displays DOWN you do not have a PPP session established If your Gateway s connection setting is set to Always On after a brief delay the PPP session will be established automatically and the PPP Status will display UP If the connection setting is set to Manual you must click on the Connect button to establish a PPP session Once the PPP session has been established PPP Status displays UP you may proceed with your Gateway s configuration 030 300500 Rev A 82 October 2006 WESTELL
65. allow you to enter the port forwarding and trigger ports ranges of your choice Go to Configuration at the homepage menu and select Services When you click on define custom service in the Service Configuration screen the Custom Service screen will guide you through the steps of creating an advanced NAT service entry via the define custom service button NOTE Westell strongly recommends that you do not change any values in this section If you experience any problems please reset VersaLink via the external hardware reset button or the procedure defined under the Maintenance menu a Z Custom Service Microsoft Internet Explorer Custom Service Set Up a Port Forwarding entry based on your specific ports WESTELL ww Sete Scotts Home Siba Configuration Maintesance Treetleshootng Heip Port Fowarding Forward a range of WAN ports to Ranges of Ports an IP address on the LAN C Trigger Ports Forward a range of ports to an IP address on the LAN only after specific outbound traffic the LAN LAN only after specific outbound traffic 030 300500 Rev A 115 October 2006 a WESTELL User Guide VersaLink Gateway Model 327W 13 1 Port Forwarding Ranges of Ports To select Port Forwarding Ranges of Ports click on define custom service from the Service Configuration screen and then select Port Forwarding Ranges of Ports from the Custom Service screen Click on Next The Port Range screen will be displayed Enter your values in the Glo
66. ample if you want to attach specific NAT services to a profile or if you want to set up a different connection setting for a profile you can create new NAT profiles and customize them to your preference NOTE You may create up to four NAT profiles and attach an unlimited number of services to each profile 030 300500 Rev A 44 October 2006 M User Guide VersaLink Gateway Model 327W E Service Configuration Microsoft Internet Explorer File Felt View Fransie Tonk Help Address ier 19 LE 1 tat bem WES TELL ce Be GEGROEI Home Statue Configuration Maintenance Troubleshooting Help Service Conflguration Current Profile Default e e Rardin Mes Legende Daes Guster Serve UPMP Enable II Service Mame Service Mode Host Devine Ire firewal e enabled the Greecll rules take procedisse over the Servicer define custom service State AAT Current Profile Displays the NAT Network Address Translation services that you have selected Service Name Drop down selection menu of NAT Network Address Translation service you can select to configure you VersaLink UPNP Enable Factory Default Disable Enabling UPNP Universal Plug and Play allows automatic device discovery by your operating system 030 300500 Rev A 45 October 2006 Pe WESTELL User Guide VersaLink Gateway Model 327W 12 2 1 Configuring UPNP on the VersaLink To enable UPNP on the Gateway perform the following steps 1 Selec
67. ance Troubleshooting Help Service Confiquration gt em Current Profile A New Service Prosle 1 si Select AS Service Name SeleciA Senice ep 4D e Denotes Custam Service UPNP Enable D Service Name Service Mode Host Devica if your firewall is enabled the firewall rules take precedence over the Services PIER Custom service Gane 030 300500 Rev A 49 October 2006 WESTELL User Guide VersaLink Gateway Model 327W 12 2 3 Editing a NAT Service Profile After you have created a NAT service profile you may edit the profile s name If you select edit from the Service Configuration screen the following screen will be displayed By selecting the edit button you can make changes to your profile name and then add NAT services to or delete them from your profile Type your new NAT service profile name in the field labeled Profile Name Zb Edit Service Profile Microsoft Internet Explorer Edit Service Profile Profile Name A New Service Profile 1 ave The following screen shows that a new profile name called My NAT Profile was entered into the Profile Name field If you want save the new profile click on save If you do not want to save the new NAT profile click close Zb Edit Service Profile Microsoft Internet Explorer Edit Service Profile Profile Name My NAT Profile save 030 300500 Rev A 50 October 2006 WESTELL User Guide VersaLink Gateway Model 327W If you clicke
68. anced LAN menu Click in the Public LAN DHCP Server Enable box A check mark will appear in the box NOTE The Public LAN feature if available from your service provider allows VersaLink to use LAN IP addresses that are accessible from the WAN Public LAN allows your computer to have global address ability To utilize the Public LAN feature on VersaLink your ISP must support Public LAN and Static IP Contact your ISP for details E Public LAN Configuration Microsoft Internet Explorer File Edit View Favorites Tools Help Discover Better Broadband Home Status Configuration Maintenance Troubleshooting Help Public LAN Configuration Public LAN DHCP Server Enable T Public LAN Enable LI Public LAN IP Address fi92 168 2 1 Public LAN Subnet Mask 255 255 255 0 030 300500 Rev A 79 October 2006 M WESTELL User Guide VersaLink Gateway Model 327W Public LAN DHCP Server Enable Default NOT CHECKED If this box is CHECKED it enables DHCP addresses to be served from the Public LAN pool Public LAN Enable Default NOT CHECKED If this box is CHECKED it enables the addresses from the Public LAN to bypass the NAT interface automatically provide one automatically provide one If you clicked the Public LAN DHCP Server Enable box the following screen will be displayed Click on the Public LAN Enable box to enable Public LAN NOTE By enabling the Public LAN DHCP Server you automatically disable the Private LAN DHC
69. and Home Status Configuration Maintenance Troubleshooting Help Single Static IP Services Firewall Wireless Basic Advanced LAN Security Advanced WAN MAC Fitter Advanced 12 6 1 ATM Loopbacks If you select ATM Loopbacks from the Configuration menu the following settings will be displayed NOTE When the Enable ATM 0 21 box is checked this feature is enabled If the box does not display a check mark this feature is disabled If you change the setting in this screen you must click on save Westell does not recommend that you change this setting e ATM Loopback Microsoft Internet Explorer File Edit View Favorites Tools Help At Discover Better Broadband Home Status Configuration Maintenance Troubleshooting Help ATM Loopback Te Enable ATM 0 21 Loopback M lt a ha DDoS eg intemet 3 Enable ATM 0 21 Loopback Factory Default ENABLED This option enables the 0 21 loopback which is used by your ISP NOTE Westell does not recommend that you change this setting 030 300500 Rev A 85 October 2006 M WESTELL User Guide VersaLink Gateway Model 327W 12 6 2 WAN Configuration The following settings will be displayed if you select WAN from the Advanced WAN menu If you change the Bridge Broadcast Bridge Multicast or Spanning Tree Protocol configurations in this screen click on the save filter settings button to allow these changes to take effect If yo
70. atus Configuration Maintenance Troubleshooting Help p Single Static IP Configuration WAN IP Address 172 24 48 5 Single Static IP is currently enabled for salle 982 030 300500 Rev A 42 October 2006 y WESTELL User Guide VersaLink Gateway Model 327W If you clicked disable in the preceding screen the following pop up screen will be displayed Click on OK Microsoft Internet Explorer S Disable IP Passthrough f Cancel If you clicked OK in the Disable IP Passthrough screen the following pop up screen will be displayed This screen will allow the modem to be reset and the new configuration will take effect Click on OK Microsoft Internet Explorer KEN 2 The modem must be reset in order for the new configuration to take affect Do wou wish to reset now If you clicked OK in the preceding screen the following screen will be displayed VersaLink will be reset and the new configuration will take effect Ee Em ge me Ze merase Resetting Modem Please Wait The neem 15 resetting in order for ihe requested changes to take efhect Your page will be reloaded shorthy aft we WEIER After a brief delay the home page will be displayed Confirm that you have a DSL sync and that your PPP session displays UP Click on the connect button to establish a PPP session Next Select Single Static IP from the Configuration menu to confirm that
71. aved or printed Selecting this button opens a new window that contains configuration settings for selecting the information that you want logged The packet number The number of days passed since that the packet was sent The time that the packet was sent The direction of transmission The internal rule that caused the logged event The internal rule is set up under Firewall rules Displays a description of the logged event 124 October 2006 WESTELL User Guide VersaLink Gateway Model 327W If you clicked on details in the Firewall Log screen the Packet Details screen will be displayed Click on close S Firewall Details Microsoft Internet Explorer Packet Details Source IP 192 168 1 47 Destination IP 204 221 192 174 Protocol TCR Source Port 2887 Destination Port 80 TCP Flags O4 rst 3 close To clear the Firewall log click clear log in the Firewall Log screen The following pop up screen will be displayed Click OK when asked Do you wish to clear the Firewall log file If you click Cancel the firewall log will not be cleared Microsoft Internet Explorer SC en l 7 Do you wish to clear the Firewall log file To obtain a printable format of the Firewall Log at the Firewall Log screen click Printable Savable Format This will allow you to send a copy of the Firewall log to your designated printer 030 300500 Rev A 125 October 2006 We WESTELL User Guide VersaLink
72. bal Port Range fields and click next to continue e Custom Service Microsoft Internet Explorer Ri Port Range Microsoft Internet Explorer Custom Service Set Up a Port Forwarding entry based on your specific ports Port Range Set Up a Port Forwarding range entry based on your specific ports Port Fowarding Forward a range of WAN ports to Service Name My New Service The above name will be saved as this Services description Global Port Range fo 0 Base Host Port fo Ranges of Ports an IP address on the LAN C Trigger Ports Forward a range of ports to an IP address on the LAN only after specific outbound traffic EGD CD Protocol TCP UDP G7 Gu 13 2 Adding Port Forwarding Ports If you made changes in the Port Range screen and clicked on next the following screen will be displayed Click on close to accept the changes or click on add to go back to Port Range screen and enter additional port range values You can repeat this step for each range of ports that you want to add up to 62 port forwarding ranges When you are finished adding ports to the Global Port Range you must click on close to accept the information you have entered and return to the Service Configuration screen Service Details Service Name My New Service Type Port Forwarding Port 1 Protocol TCP Global Porte 2 20 Base Host Port 2 enn After clicking Close you can enable your new service from the Serivce Name
73. band Latest News Products amp Services Where to Buy Technical Support News amp Events Careers About VVestell Investor Relations Business Development Contact New Managing Director for VVYestell Limited U K Subsidiary VWestell Appoints Wiliam Nack Regional Vice President of Sales T rourgil hie OU GI se conferenceplus TL 9000 bm The Telecom Quality Measurement System Home Products amp Services Where to Buy Technical Support News amp Events Careers About Westell Investors Contact Terms amp Conditions Privacy Statement Westell Technologies Inc 750 N Commons Drive Aurora IL 60504 f Omet 030 300500 Rev A 25 October 2006 Pe WESTELL User Guide VersaLink Gateway Model 327W 7 4 Disconnecting a PPP Session If you have finished browsing the Internet and want to disconnect from your Internet service provider click on the Disconnect button in the Connection Overview screen the preceding screen The following pop up screen will appear Click on OK to disconnect the PPP session CAUTION If you disconnect the PPP session this will disconnect the Gateway from the Internet and all users will be disconnected until the PPP session is re established Microsoft Internet Explorer Do you want to disconnect the PPP session j Cancel If you clicked the Disconnect button in the preceding Connection Overview screen the PPP Status should display
74. be transmitted WAN side RIP never transmits Possible responses are None RIPv1 RIPv1 Compatible RIPv2 RIPv2 Authentication Mode If using RIP V2 you must select the type of authentication to use Possible responses are None Clear Text MD5 If MDS authentication the password Default VersaLink Factory Default DISABLED If this box is check Enabled this feature will determine whether the modem advertises itself as a VersaLink 1 e the default route Border VersaLink Filtering Factory Default ENABLED If this box is unchecked Disabled the modem will not summarize subnets into a single route before advertising RIP Timer Rate Indicates how often to update the local routing table RIP Supply Interval Indicates how often to advertise routes to neighbors RIP Expire Time Indicates how long routes received from neighbors become invalid if no refresh of the route is received RIP Garbage Collection Time Indicates how long to advertise invalid routes after they have expired If you change any settings in the RIP Configuration screen and clicke on save the following screen will be displayed Click on OK to save your new RIP settings Microsoft Internet Explorer S Save and contigure AIF Cancel 030 300500 Rev A 114 October 2006 WESTELL User Guide VersaLink Gateway Model 327W 13 SETTING UP ADVANCED SERVICE CONFIGURATION You can set up additional Service Configuration options for VersaLink that
75. ble the following Service Configuration screen will display Static NAT is now enabled for the device you selected fe fi fo Favors Tee p D Bred CEDC Sa wee Cuasenp Profile CetezbR Saraca Homa iw Ende Servion Norme Bordon Moda Host Device a wee irren iz enablac Ae Greeff sauder tobe precedence over the Services Gane Enabled for traaih 1p 13 7 Disabling Static NAT If you click on static NAT in the Service Configuration screen the following screen will be displayed select a device name from the Static NAT Device drop down arrow or type the IP address of the device in the field labeled IP Address Click on disable This will automatically disable the Static NAT feature for that device Static NAT Microsoft Internet Explorer Static NAT Set Up an IP Address to be your Default NAT Destination Static NAT Device salle 982 D or specify IP Address All unsolicited inbound traffic will be sent to the above device Note Static Nat and IP Passthrough are mutually exclusive features enable disable cancel 030 300500 Rev A 121 October 2006 WESTELL User Guide VersaLink Gateway Model 327W If you click disable the following Service Configuration screen will be displayed Static NAT is now disabled for the device you selected No device is displayed in the field adjacent to the static Nat button WESTELL Discover Mamer frssassnd Home Statu
76. ces connected on the LAN Westell advises setting this to enabled for the private LAN Off DHCP Server is disabled Private LAN DHCP addresses will be saved into the Private LAN configuration Public LAN DHCP addresses will be saved into the Public LAN configuration This option is only available if the Public LAN DHCP server is enabled NOTE These addresses will be overwritten if the Internet Service Provider supports dynamic setting of these values DHCP Start Address Factory Default 192 168 1 15 This field displays the first IP address that the DHCP server will provide The DHCP Start Address must be within the IP address and lower than the DHCP End Address You may use any number from 0 to 254 in this address DHCP End Address Factory Default 192 168 1 47 This field displays the last IP address that the DHCP server will provide The DHCP End Address must be within the IP address and higher than the DHCP Start Address You may use any number from 0 to 254 in this address DHCP Lease Time Factory Default 01 00 00 00 Displays the amount of time the provided addresses will be valid after which the DHCP client will usually re submit a request NOTE DHCP Lease Time value must be greater than 10 seconds Seconds must be between 0 and 59 minutes must be between 0 and 59 and hours must be between 0 and 23 030 300500 Rev A 72 October 2006 WESTELL User Guide VersaLink Gateway Model 327W 12 5 3 Disabling the DHCP Server
77. d save in the Edit NAT Profile screen the following pop up screen will be displayed Click OK to save your new profile settings If you click on Cancel your new profile settings will not be saved Microsoft Internet Explorer Save this Profile Cancel The following screen displays the current profile If desired you may create a new profile and delete or edit an existing profile Home Status Configuration Maintenance Troubleshooting Help Service Configuration delete dit Santen E ane Kg Gus service Name Sted Semion KZ FT Depotesz Custom Service UPNP Enable Service Name Service Mode Host Device Tf your frrewall is enabled the firewall rules take precedence aver the Services define custom service amp ic 030 300500 Rev A 51 October 2006 WESTELL User Guide VersaLink Gateway Model 327W 12 2 4 Adding NAT Services to a Profile This section explains how to add NAT services to your NAT service profile Remember you may attach an unlimited number of NAT services to any profile NOTE Westell has developed an extensive list of NAT services and you may select any service from this list By selecting your specific NAT service and setting up a NAT profile you will ensure that the appropriate ports on VersaLink are open and that the required application traffic can pass through your LAN For a list of supported NAT services go to section 16 NAT Services To add a NAT service select
78. d to the modem VLAN Assigns VLAN tags to individual data ports on the modem 030 300500 Rev A 98 October 2006 Pe WESTELL User Guide VersaLink Gateway Model 327W If you selected the Routed Bridge mode under VC 1 Bridge Settings the following screen will be displayed Enter the appropriate values in the fields and click on set VC 4 C 1 Configuration Microsoft Internet Explorer File Edt View Favorites Tools Help VC 1 Configuration verfo verbs perho Qos UBR Protocol Bridge sl Status Enabled VCi1 Bridge Settings Mode Routed Bridge DHCP Client Enable Disable IP Address nun oo Gateway nunn 80t S ONS Primary nun o oo DNS Secondary nunn Help H E Done E Internet Z VC 1 Bridge Settings Routed Bridge Mode DHCP Client IP Address Gateway DNS Primary 030 300500 Rev A 99 October 2006 WESTELL User Guide VersaLink Gateway Model 327W If you selected Proxy Bridge mode under VC 1 Bridge Settings the following screen will be displayed Enter the appropriate values in the fields and click on set VC 4 C 1 Configuration Microsoft Internet Explorer File Edit View Favorites Tools Help VC 1 Configuration vib verbs perho Qos UBR Protocol Bridge sl Status Enabled Vci1 Bridge Settings Mode Frox Bridge Gateway booo o gt gt DNS Primary boon DNS Secondary 0 0 0 0 SCH SR Help ET Doe i nene Z
79. dslrouter 192 168 1 1 deviceweb 192 168 1 1 SmartDevice 192 168 1 1 dnsnamehere fi 92 168 1 25 Discovered Local Devices No Discovered Devices VersaLink Gateway Model 327W lt ED If you clicked add the following screen will be displayed The Host Name and IP Address have been added to the Static Host Assignment WESTELL Discover Better Broadband Home Status Configuration Maintenance Troubleshooting Help DNS Configuration User Assigned DNS Domain Name myhome westell com Static Host Assignment Host Name IP Address dslrouter 192 168 1 1 deviceweb 192 168 1 1 smartdevice 192 168 1 1 dnsnamehere 192 168 1 25 0 0 0 0 Discovered Local Devices No Discovered Devices 030 300500 Rev A 71 October 2006 Pe WESTELL User Guide VersaLink Gateway Model 327W 12 5 2 DHCP Configuration Private LAN The following settings will be displayed if you select DHCP from the Advanced LAN menu Si DHCP Configuration Microsoft Internet Explorer File Edit View Favorites Tools Help Discover Better Broadband Home Status Configuration Maintenance Troubleshooting Help DHCP Configuration DHCP Server Private LAN sl Private LAN DHCP Settings DHCP Start Address 192 168 1 15 DHCP End Address f192 168 1 47 DHCP Lease Time fi fo f Do A b Days Hours Minutes Seconds am as DHCP Server This setting allows VersaLink to automatically assign IP addresses to local devi
80. e cord and modular plug is provided with this product It is designed to be connected to a compatible modular jack that is also compliant See installation instruction for details If this terminal equipment Model 327W causes harm to the telephone network the telephone company may request you to disconnect the equipment until the problem is resolved The telephone company will notify you in advance if temporary discontinuance of service is required If advance notification is not practical the telephone company will notify you as soon as possible You will be advised of your right to file a complaint with the FCC if you believe such action is necessary If you experience trouble with this equipment Model 327W do not try to repair the equipment yourself The equipment cannot be repaired in the field Contact your ISP or contact the original provider of your DSL equipment The telephone company may make changes to their facilities equipment operations or procedures that could affect the operation of this equipment If this happens the telephone company will provide advance notice in order for you to make the modifications necessary to maintain uninterrupted service If your home has specially wired alarm equipment connected to the telephone line ensure that the installation of this equipment Model 327W does not disable your alarm equipment If you have questions about what will disable alarm equipment consult your telephone company or a qu
81. ed due to inactivity This feature works if you have selected the Time Out Enable feature explained above 030 300500 Rev A 36 October 2006 WESTELL User Guide VersaLink Gateway Model 327W 11 STATUS A Discover Better Broadband Home Status Configuration Maintenance Troubleshooting Help Home Connection Summary About 11 1 Connection Summary The following settings will be displayed if you select Connection Summary from the Status menu 3 Connection Summary Microsoft Internet Explorer E SS Discover Better Broadband Home Status Configuration Maintenance Troubleshooting Help F summar NOTE The actual values may differ from the values displayed in this screen DSL Connection Information Connection Rate Down Up 8064 KBits Sec by 960 KBits Sec Connection Status In Packets 106 Out Packets 100 In Error Packets 0 Out Error Packets 0 IP Network Address PPP 172 24 48 3 Primary DNS 10 16 88 116 Secondary DNS 10 16 16 2 Ethernet Status In Packets 1255441284 Out Packets 194498765 ATM NetworkAddress YPI 0 Y CI 35 Firewall Status Passed In 7 Out 7 Dropped In 6 Out O Connection Information Connection Name Connection Duration Status Number of Reconnects My Connection 00 42 36 UP 0 DSL Connection Information This field will let you know if you have a DSL signal and the DSL rate at which you are connected This field will show how much information was received IN or sent OU
82. een 7 and 20 inctusive LCP Echo Duration feo ust be between 5 and 300 seconds inctusive and greater or equal to Retry Duration LCP Echo Retry Duration fio Must De between 5 and 300 seconds inclusive Tunneling Ge Enable Disable Help 030 300500 Rev A 105 October 2006 WESTELL User Guide VersaLink Gateway Model 327W To configure the WAN Ethernet port for routed bridge protocol select ROUTED from the Protocol drop down arrow SI Ethernet WAN Configuration Microsoft Internet Explorer Pfeil E4 De Edit View Favorites Tools Help WAN Ethernet Configuration Protocol PPPoE D Status PPPoE ROUTED IP Address nun Gateway unn DNS Primary nun DNS Secondary ooo o Subnet Mask MRU Negotiation I LCP Echo Disable LCP Echo Failures D Must be between and 30 inclusive LCP Echo Duration en Must be between 5 and 300 seconds inclusive and greater or equa to Retry Duration LCP Echo Retry Duration UU Must be between 5 and 300 seconds inclusive Tunneling Enable Disable l Done g inteme A If you select ROUTED the following screen will be displayed Enter the appropriate values in the fields and click on set gt Ethernet WAN Configuration Microsoft Internet Explorer Pf E File Edit Yiew Favorites Tools Help WAN Ethernet Configuration Protocol ROUTED Status Enabled Router Settings DHCP Client Enable GG Disable IP Address
83. egez doniga Io Opie The Serhan bee epee ned By Ihe ier engine stain Specifies thal tha TCPICMPORMP geasion particular tha sequences numeer in ihe cage ee TCP ane the paekel he Ae SOUN idto SRR eSees Sed POS in h Coe OPC and SMPs ASS IaERO ith DIS Gar k t ell bd added bp the dale table mainiened by he Wiering engine Aa berg as thal asador remaina in the ele lable all paskala aprorialed vith Dal spe ane passed etin coenparing tenn bo mp mules decision tep The toning mngirestate table login maintains Te Hale of lhe tettiin wilh dietai DaCkete and closes or Serves I1 Oud rere Iii Shee alate lable eft ngegt appmpreate 59 October 2006 WESTELL User Guide VersaLink Gateway Model 327W 12 4 Wireless Configuration Discover Better Broadband Home Status Configuration Maintenance Troubleshooting Help y Single Static IP Services Firewall Wireless Hasic Advanced LAN Security Advanced WAN MAC Filter Advanced 12 4 1 Wireless Basic The following fields will be displayed if you select Wireless and then select Basic from the Configuration menu Wireless Operation Enabled ei Network Mima 5510 MiZ407001 768 Channel ml Mince Mixed AN Support Disabled Hide SSID Disabled ml IMPORTANT If you are connecting to VersaLink via a wireless network adapter the service set ID SSID must be the same for both the Westell VersaLink and your PC s wireless network adapter The default SSID for VersaLink is the seria
84. elect the desired security option IMPORTANT Client PCs can use any Wireless Fidelity Wi Fi 802 11b g g certified card to communicate with VersaLink The Wireless card and VersaLink must use the same security code type If you use WPA PSK or WEP wireless security you must configure your computer s wireless adapter for the security code that you use PECH WESTELL Home Status Configuration Maintenance Troubleshooting Help 030 300500 Rev A 63 October 2006 WESTELL User Guide VersaLink Gateway Model 327W If you select WPA PSK from the Wireless Security drop down menu following screen will be displayed Enter you WPA Shared Key in the field provided Next enter the WPA Group Rekey Interval value Click save to save the settings WESTELL Desire Halter Bie RD ta Status Configuration Maintenance Troubleshooting Help Wireless Security WPA PSE aw Wireless Securit Wireless Security Factory Default Disabled Possible Response Disabled Wireless security will be disabled on the VersaLink WPA PSK Selecting this will enable you to set up WPA PSK security on the VersaLink WEP Selecting this will enable you to set up WEP security on the VersaLink The AP card supports 64 bit 128 bit or 256 bit WEP encryption If WEP is selected any station can connect to the AP as long as its SSID matches the AP SSID If wireless security is disabled the risk of someone nearby accessing the AP is maximized WPA Shared Key T
85. ep ferae he guer rabori Species the OHF packet hee found im the ROMP header The report bpe cheeks ke both eeraigon 3 and version 2 Spe codes Mo bock is made by the parser to voir that ge IGMP eme gl is specitied Go itis up pe the usm ig Inthe he Polo Kemp rati in a cule wing Pre ig ype Core kmp ipe resi ron Species the GMP packet type found in the IMA header No check es mathe by tee parses iy wiriy Dote ICRP pertetol is Spc chee Eat up Ss Dip wee D include P photo MAP Condon in a rule using Ihe mp be Cppngdpon Alen kaywnnis Species zem further aiiin mp be Saken upih Seton Baten Iie rule pondon and the packed Content ing Gave Spaeifies thal tha contania of any malehing parket header ghould Be recorded inthe lng tabla The evel parametar L CPG Sr Ip m BAS The Siwca of ES Lon aniy This wale ule mane is Sigg wih g ch Log eny resulting foe mis rule The beg may subsequently be searched e fected by Drz waluee rule name Log erter appear in Pre lable wth a deiaull seventy od 0 Te kenteakip is presented by a decimal ar hemdecimal walur between D ang 255 glen seventy het ted Soecitesd Dat e contents of any etching patkel header should be recoded cin ihe beg able with Te Onresponding severity value ard teed explanation Severity is a decimal number behewan D acd 4 The atest tect ic Geint by brackets Beaches Galil he Berl leet dona Species that tre fitering engine should sion checking any subsequent mules should tis mle maich Thes acton Erp
86. er for the requested changes to take effect Your page will be reloaded shortly EE EES After a brief delay the home page will be displayed Confirm that you have a DSL sync and that your PPP session displays UP Click on the connect button to establish a PPP session Next Select Single Static IP from the Configuration menu to confirm that Single Static IP is enabled as shown in the following screen 030 300500 Rev A 4 October 2006 WESTELL User Guide VersaLink Gateway Model 327W SI Single Static IP lt br gt Configuration Microsoft Internet Explorer Eile Edit View Favorites Tools Help WESTELL GE Discover Better Broadband Home Status Configuration Maintenance Troubleshooting Help i Single Static IP Configuration WAN IP Address 172 24 48 5 Single Static IP is currently enabled for salle 982 IMPORTANT After you enable Single Static IP you must reboot your computer NOTE If you chose to enable User Configured PC wait for the Gateway to reset and then manually enter the WAN IP Gateway and Subnet mask addresses you obtained from your Internet service provider into a PC 12 1 2 Disabling Single Static IP Single IP Address PassThrough To disable Single Static IP select Single Static IP from the Configuration menu Click on disable e Single Static IP lt br gt Configuration Microsoft Internet Explorer File Edit View Favorites Tools Help WESTELL Discover Better Broadband Home St
87. esPropd ddress drop from addr 0 0 0 0 gt gt done alert 4 0 0 0 0 Source IP Address RulesPassUDP pass protocol udp to port 53 gt gt done pass protocol udp from port 53 gt gt done RulesDropIcCMP drop protocol icmp gt gt alert 4 ICMP Message To WAN IP end NOTE The information displayed in this screen depends on the level of security you have selected S Internet A If you clicked Apply in the User Define Firewall Rules screen the following pop up screen will be displayed Click on OK if you want your new firewall setting to take effect If you click Cancel your new firewall settings will not take effect Microsoft Internet Explorer E4 P Do wish to apply these Rules and switch your Securty Level to User H Cancel 030 300500 Rev A 57 October 2006 Pe WESTELL User Guide VersaLink Gateway Model 327W If you want to save your new firewall settings click save in the screen labeled User Define Firewall Rules NOTE Westell recommends that you do not change the settings in the User Defined Firewall Rules screen If you need to reset VersaLink to factory default settings push the reset button on the rear of VersaLink 4 Firewall Rules Microsoft Internet Explorer File Edt View Favortes Tools Help WEST BE Sincere cea inbound L Security Level 1 IN rules FulesFass pass all RulestDropa ddress drop from addr 0 0 0 0 gt gt done alert 4 0 0 0 0 Source IP
88. esponses are Boundary 1 0 ms Boundary 2 10 ms Boundary 3 30 ms Boundary 4 40 ms Boundary 5 100 ms Boundary 6 1000 ms Boundary 7 3000 ms IP Fragmentation Enable Factory Default DISABLED If this box is checked IP Fragmentation will be Enabled If Enabled and packets larger than 1500 bytes total are received they will be fragmented IP Fragment Size This is the IP Packet Size Possible responses are 100 148 244 292 340 388 or 436 If you made changes to the QOS Configuration and clicked on save the following screen will be displayed Click on OK This will save your new QOS settings Microsoft Internet Explorer Save and configure QOS Cancel 030 300500 Rev A 110 October 2006 p User Guide VersaLink Gateway Model 327W 12 6 8 Route The following settings will be displayed if you select Route from the Advanced WAN menu The Route table maintains the routes or paths of where specific types of data shall be routed across a network A WESTELL Discover Setter Broadband Home Status Configuration Maintenance Troubleshooting Help IP Interfaces Address Subnet Mask 192 168 1 1 255 255 255 0 127 0 0 1 255 0 0 0 Network Routing Table Destination Subnet Mask Gateway Interface Metric Rip 192 168 1 0 255 255 255 0 192 168 1 1 eth 0 N A Host Routing Table Destination Gateway Interface Metric Rip 127 0 0 1 127 0 0 1 loQ 0 N A 192 168 1 1 127 0 0 1 loQ 0 N A Inactive Routes Dest
89. essages are included in this count IN Fragments The number of fragments successfully received This may not be equal to the sum of the Unicast and Multicast frames because large frames are broken into multiple transmissions The number of fragments per frame is based on the Fragmentation Threshold setting not user configurable on the source station IN Frames after one or more The number of frames that successfully transmitted after more than one retrie retry Any fragment of a frame that required multiple retries would increment this counter for the whole frame IN Drops due to insufficient Rx The number of received frames discarded due to lack of buffer space buffers 030 300500 Rev A 143 October 2006 User Guide VersaLink Gateway Model 327W 15 5 Status ouer Better Broadband Home Status Configuration Maintenance Troubleshooting Help Home System Self Tests Diagnostic Logs Statistics F Status E Wireless Stations Connection Overview RIP Table 005 DSL Connect Rate Down Up 8064 KBits Sec by 1024 KBits Saye 15 5 1 LAN Devices The following settings will be displayed if you select LAN Devices from the Status menu J LAN Statistics Microsoft Internet Explorer Eile Edit View Favorites Tools Help WESTELL EE Discover Better Broadband Home Status Configuration Maintenance Troubleshooting Help LAN Statistics HHH will Devices On LAN IP Address MAC Address Name Status 192 168
90. estination Address The IP address or subnet of the Route Subnet Mask If the Route is a network route Subnet Mask is used to specify the subnet address If the Route is a Host route then the Host Route check box is used Indicates were to send the packet if it matches this route Indicates were to send the packet if it matches this route The RIP metric to be assigned to this route if and when it is advertised using RIP RIP Indicates whether a static route should be advertised via RIP VersaLink Interface Metric Inactive Routes Inactive Routes Static routes whose interface is currently not in service Destination Address The IP address or subnet of the Route Subnet Mask If the Route is a network route Subnet Mask is used to specify the subnet address If the Route is a Host route then the Host Route check box is used Subnet Mask Host Route If the Route is a network route Subnet Mask is used to specify the subnet address If the Route is a Host route then the Host Route check box is used VersaLink IP Address The interface to use for sending the packet if it matches this route Only active VersaLinks can be used to create a static route The RIP metric to be assigned to this route if and when it is advertised using RIP enabled before the route will be advertised not checked the route will disappear the next time the modem restarts 030 300500 Rev A 112 October 2006 WESTELL User Guide VersaLink
91. et Avg Packet Rate Per second Queue Number Not Time Stamped The packets with no incoming time stamp Often these are generated internal to the modem A ms to B ms The number of packets of this priority whose time in the modem fell between A and B milliseconds Time is measured from the point the packet arrives at the modem s processor until is passed to the ATM hardware for transmission Queue Number Possible ranges are A ms to B ms 0 ms to 10 ms 10 ms to 20 ms 20 ms to 40 ms 40 ms to 100 ms 100 ms to 1000 ms 1000 ms to 3000 ms Larger than 3000 ms 030 300500 Rev A 148 October 2006 WESTELL User Guide VersaLink Gateway Model 327W 15 5 5 VOIP Status The following settings will be displayed if you select VOIP from the Status menu NOTE A VOIP device must be connected to the Gateway for this table to be populated YDIP Status Microsoft Internet Explorer File Edit View Favorites Tools Help Discover Better Broadband Home Status Configuration Maintenance Troubleshooting Help YOIP Status SIP Registry Information Local IP Addr Expiration SIP Registry Information URI The SIP URI that is trying to register This field only indicates that a SIP device ku tried to register not that it succeeded 030 300500 Rev A 149 October 2006 a WESTELL User Guide VersaLink Gateway Model 327W 16 NAT SERVICES For your convenience VersaLink supports protocols for Applicati
92. et connection is functioning properly Congratulations You have completed the Ethernet hardware installation No software installation is required when using only an Ethernet connection Proceed to section 7 to configure VersaLink for Internet connection 030 300500 Rev A 13 October 2006 Pe WESTELL User Guide VersaLink Gateway Model 327W Computer ES Ethernet Card o ei Gonnector L a eg ei Figure 1 Connection via 10 100 Base T Ethernet 6 4 2 Connecting PCs via Wireless IMPORTANT If you are connecting to VersaLink via a wireless network adapter the SSID must be the same for both VersaLink and your PC s wireless network adapter The default SSID for VersaLink is the serial number of the unit located below the bar code on the bottom of the unit and also on the Westell shipping carton Locate and run the utility software provided with your PC s Wireless network adapter and enter the SSID value The PC s wireless network adapter must be configured with the SSID in order to communicate with VersaLink before you begin the account setup and configuration procedures Later for privacy you can change the SSID by following the procedures outlined in section 12 4 Wireless Configuration NOTE Client PCs can use any Wireless Fidelity Wi Fi 802 1 1b g certified card to communicate with VersaLink The Wireless card and VersaLink must use the same Wired Equivalent Privacy WEP security code type The factory default fo
93. f each screen and will allow you to navigate you to the various configuration options of your VersaLink Gateway If you are at a screen and need help click on the Help button to learn more about that screen Please note that the menu options displayed will vary according to the WAN configuration you have chosen to use DSLATM PORT or ETHERNET PORT1 However all menu options are displayed when VersaLink is enabled for DSLATM PORT Instructions on enabling and disabling DSLATM PORT and ETHERNET PORT 1 are explained in section 12 6 Advanced WAN This document was created with the VersaLink DSLATM PORT enabled The sections explained throughout this document will indicate when a menu item is unavailable 030 300500 Rev A 32 October 2006 A WESTELL User Guide VersaLink Gateway Model 327W 10 HOME As you navigate through the various screens of VersaLink the name of the active page that you have selected will appear in the upper left corner of the screen as shown below Please note that the actual values may differ from the values displayed in the screens E wire peed Dual Connect Microsoft internet Eapkaen EEN bh WESTELL ana Status Configuration Maintenance Troubleshooting Hein If you have set up your account profile and established your PPP session as discussed in section 7 the following settings will be displayed when you click on your Home page Click on profile editor to edit your connectio
94. fer pledge lease rent or share your rights under this License Agreement You agree that you may not nor allow others to reverse assemble reverse compile or otherwise translate the SOFTWARE You may retain the SOFTWARE CD for backup purposes only In addition you may make one copy of the SOFTWARE in any storage medium for backup purposes only You may make one copy of the User s Manual for backup purposes only Any such copies of the SOFTWARE or the User s Manual shall include Licensor s copyright and other proprietary notices Except as authorized under this paragraph no copies of the SOFTWARE or any portions thereof may be made by you or any person under your authority or control 2 Licensor s Rights You acknowledge and agree that the SOFTWARE and the User s Manual are proprietary products of Licensor protected under U S copyright law You further acknowledge and agree that all right title and interest in and to the SOFTWARE including associated intellectual property rights are and shall remain with Licensor This License Agreement does not convey to you an interest in or to the SOFTWARE but only a limited right of use revocable in accordance with the terms of this License Agreement 3 License Fees The fees paid by you under the support agreement are paid in consideration of the licenses granted under this License Agreement 4 Term This License Agreement is effective upon your opening of this package and shall continue until termi
95. g terms hereof 10 No Waiver The failure of either party to enforce any rights granted hereunder or to take action against the other party in the event of any breach hereunder shall not be deemed a waiver by that party as to subsequent enforcement of rights or subsequent actions in the event of future breaches 21 PUBLICATION INFORMATION Westell VersaLink Gateway Model 327W User Guide Part Number 030 300500 Rev A Copyright 2006 Westell Inc All rights reserved Westell Inc 750 North Commons Drive Aurora Illinois 60504 USA www westell com All trademarks and registered trademarks are the property of their respective owners 030 300500 Rev A 157 October 2006
96. hat is useful in identifying the station 12 4 4 Wireless Advanced Configuration The following screen will be displayed if you select Wireless and then select Advanced from the Configuration menu WESTELL Diicower UH Broeabend Home Statue Configuration Maintenance Trowbleahooting Help Wireless Advanced Gonfiguration Wireless Advanced Contiquration Beacon Pano ATS Thrashald Fragmentation Threshold 3 Slot Time Alganthm PACE Algorithm Wireless Advanced Configuration Beacon Period The time interval between beacon frame transmissions Beacons contain rate and capability information Beacons received by stations can be used to identify the access points in the area RTS Threshold RTS CTS handshaking will be performed for any data or management MPDU containing a number of bytes greater than the threshold If this value is larger than the MSDU size typically set by the fragmentation threshold no handshaking will be performed A value of zero will enable handshaking for all MPDUs Fragmented Threshold Any MSDU or MMPDU larger than this value will be fragmented into an MPDU of the specified size Preamble Algorithm Factory Default Local STA s Possible Responses Always Long Transmissions are done using the long preamble algorithm Always Short Transmissions are done using the short preamble algorithm Local STA s If all associated stations support short preamble then the short 030 300500 Rev A 67 October
97. he ACTA A label on the bottom of this equipment contains among other information the Ringer Equivalence Number REN and the product identifier For products approved after July 23 2001 the product identifier is in the format US AAAEQ TXXXX The digits represented by are the REN without a decimal point e g 03 is a REN of 0 3 The REN is used to determine the number of devices that may be connected to a telephone line For earlier products the REN is separately shown on the label If requested this number must be provided to the telephone company Excessive RENG on a telephone line may result in the devices not ringing in response to an incoming call In most but not all areas the sum of RENs should not exceed five 5 0 To be certain of the number of devices that may be connected to a line as determined by the total RENs contact the local telephone company This equipment is designated to connect to the telephone network or premises wiring using a compatible modular jack that is Part 68 compliant An FCC compliant telephone cord and modular plug is provided with the equipment See the Installation Information section of this User Guide for details 030 300500 Rev A 5 October 2006 WESTELL User Guide VersaLink Gateway Model 327W A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA A compliant telephon
98. hernet Bridge Bridge Protocol Classical IPoA Internet Protocol over ATM Asynchronous Transfer Mode This is an ATM encapsulation of the IP protocol VC 1 Bridge Settings Bridge A bridge is a layer 2 device that connects two segments of the same LAN that use the same protocol such as Ethernet The modem does not have a WAN IP address in this mode The client PC will typically get an IP address from a DHCP server in the network or the IP address can be assigned to the client PC statically Routed Bridge Routed Bridged Encapsulation RBE is the process by which a bridged segment is terminated on a routed interface Specifically VersaLink 1s routing on an IEEE 802 3 or Ethernet header carried over RFC 1483 bridged ATM RBE was developed to address the known RFC1483 bridging issues including broadcast storms and security The modem will get a WAN IP address through Mode DHCP or can be assigned statically NAT will use the global address assigned to the modem Proxy Bridge Proxy Bridge is the process in which the modem acts as a proxy ARP agent for a local public subnet The modem will be assigned an IP address from within that public subnet The modem will direct all traffic to a VersaLink which is configured statically VersaLink address must not reside within VersaLink s assigned public subnet All traffic will be sent via VersaLink s MAC address The LAN may also have a private NA Ted network NAT will use the global address assigne
99. his is a passphrase also called a shared secret that must be entered in both the wireless router and the wireless client This shared secret can be between 8 to 63 text characters or 64 hexadecimal characters and can include special characters and spaces The WPA Shared Key should be a random sequence of either keyboard characters upper and lowercase letters numbers and punctuation at lease 20 characters long or hexadecimal digits numbers 0 9 and letters A F at least 24 hexadecimal digits long The more random your WPA Shared Key the safer it is to use WPA Group Rekey Factory Default 3600 Interval The number of seconds between rekeying the WPA group key A zero 0 means that rekeying is disabled 030 300500 Rev A 64 October 2006 WESTELL User Guide VersaLink Gateway Model 327W If you select WEP from the Wireless Security drop down menu the following screen will be displayed After you have entered the appropriate values in the fields provided click save to save the settings WESTELL Danmar Peer Bpsipaea Hees Status Configuration Maintenance Troubleshooting Help Wireless Security Wireless Security Factory Default Disabled Possible Response Disabled Wireless security will be disabled on the VersaLink WPA PSK Selecting this will enable you to set up WPA PSK security on the VersaLink WEP Selecting this will enable you to set up WEP security on the VersaLink The AP card supports 64 bit 128 bit or
100. in the Mode drop down arrow under VC 1 Bridge Settings E C 1 Configuration Hicrosoft Internet Explorer File Edit Wiew Favorites Tools Help VC 1 Configuration vil vc pcr hoo aos UBR sl Protocol Bridge H Status Enabled VC 1 Bridge Settings en a E eiweg 030 300500 Rev A 97 October 2006 WESTELL User Guide VersaLink Gateway Model 327W VC 1 Configuration This setting allows you to change your VPI Virtual Path Indicator value for a particular VC which is defined by your Service Provider This setting allows you to change your VCI Virtual Channel Indicator value for a particular VC which is defined by your Service Provider PCR Factory Default 100 Peak Cell Rate PCR The maximum rate at which cells can be transmitted across a virtual circuit specified in cells per second and defined by the interval between the transmission of the last bit of one cell and the first bit of the next This value is a percentage of the current data rate 100 allows this VC to use 100 of the available bandwidth 80 allows this VC to use 80 of the available bandwidth Quality of Service which is determined by your Service Provider CBR Constant Bit Rate UBR Unspecified Bit Rate VBR Variable Bit Rate Protocol The Protocol for each VC which is specified by your Service Provider PPPoA Point to Point Protocol over ATM Asynchronous Transfer Mode PPPoE Point to Point Protocol over Et
101. ination Subnet Mask Gateway Interface Metric Rip Add Route Destination Address 0 000 Subnet Mask bunn op HostRoute Gateway None op LAN Gateway Address Metric fo RIP Config NEVER d M Save To Modem add NOTE In this screen VersaLink represents Gateway 030 300500 Rev A 111 October 2006 a WESTELL User Guide VersaLink Gateway Model 327W To add a Route enter a Subnet Mask address or check the Host Route box Click on the add button to establish a Static route IP Interfaces The list of active interfaces on the modem and their IP and Subnet mask address EthO is the local LAN interface IP Interfaces Lol is the loopback interface Address The IP interface address Subnet Mask The IP interface subnet address Name The IP interface device name Network Routing Table Network Routing Table The list of network routes These can be either routes for directly connected interfaces or static routes Destination Address The IP address or subnet of the Route If the Route is a network route Subnet Mask is used to specify the subnet address Subnet Mask If the Route is a Host route then the Host Route check box is used VersaLink Interface Metric RIP Host Routing Table The list of host routes A host route is an IP route with a 32 bit mask indicating a Host Routing Table single destination as opposed to a subnet which could match several destinations D
102. ing Tree Protocol will allow the bridges to exchange information so that only one of them will handle a given message that is being sent between two computers within the network NOTE Spanning Tree can t be enabled if VLAN is enabled 030 300500 Rev A 87 October 2006 a WESTELL User Guide VersaLink Gateway Model 327W 12 6 2 1 Enabling DSLATM PORT Disabling ETHERNET PORT 1 if Applicable NOTE When using the optional uplink port E1 Ethernet LAN connection is limited to E2 E3 and E4 The UPLINK feature is optional If UPLINK 1s not enabled VersaLink will use DSL and wireless only To configure the VersaLink so that it uses the DSL port select DSLATM PORT from the WAN PORT drop down arrow By selecting DSLATM PORT you will enable the VersaLink s DSL transceiver This will disable the WAN Ethernet port and allow the WAN interface to use the DSL port NOTE All of VersaLink s menu options are displayed if VersaLink is configured for DSLATM PORT E WAN Configuration Microsoft Internet Explorer File Edit View Favorites Tools Help A j Discover Better Broadband Home Status Configuration Maintenance Troubleshooting Help WAN Configuration EX WAN PORT DSLATM PORT D DSLATM PORT lt Status ETHERNETPORTI H Enable PPPoE Disable D Bridge Disable D 37 Bridge Disable 38 Bridge Disable D 39 Bridge Disable D 40 Bridge Disable D 41 Bridge Bridge Broadcast kW Bridge Multicast
103. k the set VC button the following pop up screen will be displayed Click on OK in the pop up screen If you click on Cancel the new settings will not be saved After you click on OK follow the instructions to reset the Gateway as previously discussed in section 12 6 3 Microsoft Internet Explorer 2 Set this Bridge YC configuration Lancel 030 300500 Rev A 102 October 2006 Pe WESTELL User Guide VersaLink Gateway Model 327W 12 6 6 Configuring VC Protocol Settings for ETHERNET PORT 1 To configure the Gateway s VC settings via the Ethernet uplink port select ETHERNET PORT 1 at the WAN Port drop down arrow Z WAN Configuration Microsoft Internet Explorer File Edit View Favorites Tools Help Discover Better Broadband Home Status Configuration Maintenance Troubleshooting Help WAN Configuration WAN PORT DSLATM PORT D DSLATM PORT Status ETHERNET PORT Enable D 0 36 PPPOE Disable D 43 Bridge 37 Bridge 0 Disable Disable 9 38 Bridge Disable 39 Bridge Disable o Disable D 40 Bridge 41 Bridge Bridge Broadcast Vv Bridge Multicast Vv Spanning Tree Protocol l save filter settings If you select ETHERNET PORT 1 the following pop up will be displayed Click on OK Microsoft Internet Explorer sl N This change will disable your DSL port The WAN interface will be changed to ethernet port 1 030 300500 Rev A 103 October 2006 a WESTELL U
104. kets received on the Ethernet interface In Discard Packets The number of discarded packets received 030 300500 Rev A 139 October 2006 Pe WESTELL User Guide VersaLink Gateway Model 327W Out Non Unicast Packets The number of non Unicast packets transmitted on the Ethernet interface Out Unicast Packets The number of Unicast packets transmitted on the Ethernet interface Out Octets The number of bytes transmitted on the Ethernet interface Maximum Transmission Unit The number of data bytes contained in the Ethernet frame Interface Type A unique identifier that represents the interface type Interface Description A description field that refers to the interface type 15 3 2 DSL Transceiver Statistics The following settings will be displayed if you select DSL Transceiver from the Statistics menu NOTE If VersaLink is configured using ETHERNET PORT 1 the following screen will not be available Z Transceiver Statistics Microsoft Internet Explorer Ele Edt View Favorites Tools Help ver Better Broadband Home Status Configuration Maintenance Troubleshooting Help Transceiver Statistics Transceiver Revision 01 00 09 00 vendor ID Code 4 Line Mode G DMT Mode Data Path Fast Transceiver Information Down Stream Path Up Stream Path DSL Speed Kbits Sec 8064 992 Margin db 11 0 5 0 Line Attenuation db 5 0 3 5 Transmit Power db Hz 9 0 11 1 The operational mode Modes supported are No M
105. ketwill ba paged pr groppeg The condition deine the paion ofthe packed and the Eil stinging which twil p companied The action keyed max pici baiana Achoris bh bp biki Filter Keywords Thre ROL filler lokari m r be ether padded or droped pees Species that ie matching pockot is in be passed onin the associated intenmaor or the BENS ML ep Species thal the matory packel will eet be Kceearded lo the ageocialed interface or lhe SEHE MUH Condition Reeg The condition mgenssion determines H We ulie bs a maleh torte ghen packet ll Specifies all packels Ifthe all coercion ia specified in a rule all other carilat are ignored Ich bya affzeilbNMtzkpotoasbh Speri ane or more Geplicl bi Strings and z zels inte Pet layer header to Conpare This hepword a followed bry three Garpmelera The Msl oorhet parancvet r ia Pre hedder larer vad vaiet include 2 thowgh 4 tRthamate 3 ine 3 toplucddicenplign 4 The second numeric parameter is the cfset inin he pachat iy bagin the companson T aed lhi Sind hid parameter H he nopneseniabon of F bil Shing and comparsion bil meesktsell The bil singh ia dabredied wh the spen ane cage cory braces On A colon delimita fe bi sting and mask Eno maak ia priden 3 Paaek waht fat ongs b aS Sune Each be of ihe bi Sting and midek ig r brgzenle Eat A et chariyta F ec nal rartiber and ra separated by wide pace fom lhe peeves bde repredeniaben from dp addr ipsa pon port pert gt pert a pert gt porte Species particula
106. l i S 35 NOTE Depending on your Internet Service VERO Baas Provider the VPI VCI screen may come pre configured and it will be displayed here next In this case you should not change any values in this screen Click on next to go to the PROTOCOL screen Help 030 300500 Rev A 19 October 2006 M WESTELL User Guide VersaLink Gateway Model 327W Select the Protocol type that you obtained from your Internet service provider Click on next PROTOCOL Protocol PPPoE D PPPoA NOTE Depending on your Internet Service SS Provider the PROTOCOL screen may next come pre configured and it will be displayed here In this case you will need to click on next to go to the SET UP COMPLETE screen When the SET UP COMPLETE screen appears you have successfully completed your Account Profile setup Click done e Done Microsoft Internet Explorer SET UP COMPLETE Congratulations you have successfully established a connection profile one 030 300500 Rev A 20 October 2006 We WESTELL User Guide VersaLink Gateway Model 327W If you changed the VPI VCI settings and clicked done in the SET UP COMPLETE screen the following pop up screen will appear Click OK NOTE The following pop up will appear only if you have changed the VPI VCI or Protocol values in the preceding screens If you did not change any of these values this pop up screen will not appear and the Gateway will not be reset If you
107. l number of the unit located below the bar code on the bottom of the unit and also on the Westell shipping carton Locate and run the utility software provided with your PC s Wireless network adapter and enter the SSID value The PC s wireless network adapter must be configured with the SSID in order to communicate with VersaLink before you begin VersaLink s account setup and configuration procedures For privacy you should change the Network Name SSID value in the Wireless Configuration screen to your desired value 030 300500 Rev A 60 October 2006 Pe WESTELL User Guide VersaLink Gateway Model 327W Wireless Configuration Wireless Operation Factory Default Enabled When disabled no stations will be able to connect to the VersaLink Network Name SSID This string 32 characters or less is the name associated with the AP To connect to the AP the SSID on a Station card must match the SSID on the AP card or be set to ANY Channel Factory Default 6 The AP transmits and receives data on this channel The number of channels to choose from is pre programmed into the AP card Station cards do not have to be set to the same channel as the AP the Stations scan all channels and look for an AP to connect to Mode Factory Default Mixed This setting allows station to communicate with VersaLink Possible Responses Mixed Station using any of the 802 11b 802 11b and 802 11g rates can communicate with VersaLink
108. l repair any defective Westell equipment without cost during the warranty period if the unit is defective for any reason other than abuse improper use or improper installation or acts of nature Before returning the defective equipment request a Return Material Authorization RMA number from Westell An RMA number must be quoted on all returns When requesting an RMA please provide the following information Product model number on product base Product serial number on product base Customer ship to address Contact name Problem description Purchase date After an RMA number is obtained return the defective unit freight prepaid along with a brief description of the problem to one of the following options North America U K Europe Westell Inc Westell Ltd ATTN R G M Department Ringway House 750 N Commons Drive Bell Road Aurora IL 60504 7940 USA Daneshill Basingstoke RG24 8FB United Kingdom Westell will continue to repair faulty equipment beyond the warranty period for a nominal charge Contact a Westell Technical Support Representative for details 030 300500 Rev A 154 October 2006 Pa MESS TELL User Guide 19 PRODUCT SPECIFICATIONS VersaLink Gateway Model 327W e DSL Line Code Discrete Multi Tone DMT e DSL Rates 32 kbps to 8 Mbps downstream and 32 kbps to 800 kbps upstream e Power spectral density less than 34 dBm Hz e DSL Impedance 100 Ohms e DSL Performance per ITU Recommendation G
109. layed if you select Firewall from the Configuration menu SI Firewall Configuration Microsoft Internet Explorer EE Discover Better Broadband Home Status Configuration Maintenance Troubleshooting Help Firewall Configuration Security Level Control outbound traffic initiated from within the local network inbound traffic may be controlled by configuring Port Forwarding High Blocks all outgoing traffic except Mail News Web FTP and IPSEC Same as high end user can set custom rules through NAT Medium configuration Low Only known security holes are protected None All traffic is allowed Custom Customize settings Remote Logging Enable I Remote IP Address 192 168 1 47 Security Level High security level only allows basic Internet functionality Only Mail News Web FTP and IPSEC are allowed All other traffic is prohibited Medium Like High security Medium security only allows basic Internet functionality by default However Medium security allows customization through NAT configuration so that you can enable the traffic that you want to pass Low Factory Default Low pe The Low security setting will allow all traffic except for known attacks With Low security VersaLink is visible to other computers on the Internet Custom Custom is an advanced configuration option that allows you to edit the firewall configuration directly NOTE only the most advanced users should try this Remote Logging Enable Factor
110. loading File Erasing Flash Erasing Flash Flash Erased Programing Flash 030 300500 Rev A 131 October 2006 a WESTELL User Guide VersaLink Gateway Model 327W The screen below shows that the upload was successful The Gateway will not reboot WireS peed Dual Connect Upgrade Software Microsoft Internet Explorer Miel EG Software Upgrade Click browse to select the upgrade file Then start the transfer by clicking the upload file button Upgrade File Browse Upload file Help File Uploaded Update Complete Please wait 15 seconds as your modem reboots The following screen will be displayed as VersaLink is being reset A Reset Microsoft Internet Explorer Bisi E File Edit View Favorites Tools Help ww Discover Better Broadband Home Status Configuration Maintenance Troubleshooting Help Resetting Modem Please Wait The modem is resetting in order for the requested changes to take effect Your page will be reloaded shortly l SI Done g Intenet After a brief delay the home page will be displayed Confirm that you have a DSL sync and that the PPP Status displays UP Click on the reset button to re establish your PPP session 030 300500 Rev A 132 October 2006 M WESTELL User Guide VersaLink Gateway Model 327W 15 TROUBLESHOOTING NOTE Options in the Troubleshooting menu may or may not be displayed depending on VersaLinks WAN Configuration
111. ly RJ 45 Ethernet cable RJ 11 Phone cable SMA Antenna Westell CD ROM containing User Guide in PDF format Quick Start Guide 6 3 Microfilters ADSL signals must be blocked from reaching each telephone answering machine fax machine computer modem or any similar conventional device Failure to do so may degrade telephone voice quality and ADSL performance Install a microfilter if you desire to use the DSL equipped line jack for telephone answering machine fax machine or other telephone device connections Microfilter installation requires no tools or telephone rewiring Just unplug the telephone device from the baseboard or wall mount and snap in a microfilter next snap in the telephone device You can purchase microfilters from your local electronics retailer or contact the original provider of your DSL equipment 030 300500 Rev A 12 October 2006 WESTELL User Guide VersaLink Gateway Model 327W 6 4 Hardware Installations NOTE If you are using VersaLink in conjunction with an Ethernet Hub or Switch refer to the manufacturer s instructions for proper installation and configuration When using a Microfilter be certain that the DSL phone cable is connected to the DSL HPN non filtered jack Please wait until you have received notification from your ISP that your DSL line has been activated before installing VersaLink Westell recommends the use of a surge suppressor to protect equipment attached to the power supply
112. n ETHERNET through E4 Connector Switch Connector VersaLink Model 327W Rear View 030 300500 Rev A 10 October 2006 a WESTELL User Guide VersaLink Gateway Model 327W 5 3 Connector Descriptions The following chart displays the connector types SYMBOL NAME TYPE FUNCTION Connects to an ADSL equipped telephone jack or DSL LINE 6 pin RJ 11 modular jack DSL connection of a POTS splitter ETHERNET 8 pin RJ 45 modular jack Connects the Ethernet device to the PC Wireless ANTENNA SMA connector and antenna Connects to wireless IEEE 802 1 1b g g 5 4 Pin out Descriptions The following tables list the pin out descriptions DSL Pin outs Ethernet Optional Uplink Port Pin outs Rx 4 5 7 8 a es 030 300500 Rev A 11 October 2006 Pa WESTELL User Guide VersaLink Gateway Model 327W 6 INSTALLING THE HARDWARE 6 1 Installation Requirements To install VersaLink you will need the following e A Network Interface Card NIC installed in your PC or e An IEEE 802 11b g adapter NOTE Internet service provider subscriber software and connection requirements may vary Consult your ISP for installation instructions Please wait until you have received notification from your ISP that your DSL line has been activated before installing VersaLink and the software 6 2 Before you begin Make sure that your kit contains the following items Westell VersaLink Gateway Power Supp
113. n profile NOTE If you have created multiple account profiles select the option button for the active account profile 3 Application image Microsoft Internet Explorer File Edit View Favorites Tools Help WESTELL Discover Better Broadband Home Status Configuration Maintenance Troubleshooting Help Wl ul Ht Connection Overview DSL Connect Rate Down Up 8064 KBits Sec by 1024 KBits Sec Connection Name PPP Status My Connection UP disconnect ED Profile with the is your default profile To make changes to your default profile click on the profile editor button This Connection Name is from the connection profile that you established in section 8 PPP Status UP PPP session established DOWN No PPP session established Connect Disconnect CONNECT Establish a PPP session DISCONNECT Disconnect a PPP session Profile Editor This allows you to make changes to the profile that you created in section 8 030 300500 Rev A 33 October 2006 p WESTELL User Guide VersaLink Gateway Model 327W 10 1 Adding Account Profiles If you select the Profile Editor button from your Home page the Advanced Home screen will appear as shown below Click on the new connection button in the Advanced Home screen The New Connection screen will appear Enter your account profile information and click on New Next click on OK in the pop up screen to save your new connection If you do not want to add a connection
114. n Greco of 3 keep dotinibon would Keis iki the follereving Deel ROG ec MOL ie Tht piekel ee Grrr does nol ese bie There are intended So provide n gbop aoooceted wih the Ale The user iertece eats the kiy Gr npon and valve pair ae andara bari Rulz Section Trt Pubes Secon ofthe ROL gie cu puter is ApEmdet By the agin an ceed rreng The rules listed Baten hese Himig ant parsed ard corrected lo a deticion bee dala sbuachg uted by lhe packet Mier engive The rules Kaled ace mmgiereged sequentially ap lished in Fre ROL soute Ontre the packet fier engine finds a match fora nig wil node thie iher action to be taken pass ordmph and continue to compare ihe Gilet cules wilh Se ghen g tt unless ohentaa inskuced gee Pre desoripbon of the done acho in serion 22313 0 Rube Hames ADL ruler may be ghen names The packed logging facility and the user internace uses Tece miia names Anama apples in all mules Pollo ht g ta inte Bulge Becton unt anihi harmi i ed Ce Dr ong SHO An donee ee or med Sph ren characters Beginning Wah an Slip character on a lise by Baahi deslarga a mew P pp for the sipeng rulete ROL Comments Comments pegi wih fee charatier Tet parser ignores HI tharis following the commend character bo Prt ard of Be lire ROL Command Syntax Be REL cornered pirti of a Hier kezeeord follegt by a condilion expression oplercally followed By one or more arian keywerds Fr Sabre Caia ee Aor Ae The filter keyword Epptlf ez tthe par
115. n condensing EMC Safety Regulatory Certifications e EMC FCC Part 15 Class B UL Standard 60950 3 Edition CAN CSA Standard C22 2 No 60950 UL CSA ACTA 968 A Industry Canada CS03 October 2006 Pa WESTELL User Guide VerrsaLink Gateway Model 327W 20 SOFTWARE LICENSE AGREEMENT READ THE TERMS AND CONDITIONS OF THIS LICENSE AGREEMENT CAREFULLY THIS SOFTWARE IS COPYRIGHTED AND LICENSED NOT SOLD BY INSTALLING AND OPERATING THIS PRODUCT YOU ARE ACCEPTING AND AGREEING TO THE TERMS OF THIS LICENSE AGREEMENT IF YOU ARE NOT WILLING TO BE BOUND BY THE TERMS OF THIS LICENSE AGREEMENT YOU SHOULD PROMPTLY RETURN THE SOFTWARE AND HARDWARE TO WESTELL TECHNOLOGIES INC THIS LICENSE AGREEMENT REPRESENTS THE ENTIRE AGREEMENT CONCERNING THE SOFTWARE BETWEEN YOU AND WESTELL TECHNOLOGIES INC REFERRED TO AS LICENSOR AND IT SUPERSEDES ANY PRIOR PROPOSAL REPRESENTATION OR UNDERSTANDING BETWEEN THE PARTIES 1 License Grant Licensor hereby grants to you and you accept a nonexclusive license to use the Compact Disk CD and the computer programs contained therein in machine readable object code form only collectively referred to as the SOFTWARE and the accompanying User Documentation only as authorized in this License Agreement The SOFTWARE may be used only in connection with the number of systems for which you have paid license fees as dictated in your support agreement You agree that you will not assign sublicense trans
116. n this screen Model Number 490 327 W11 06 Serial Number 042406000484 MAC Address 00 0f db 00 01 39 Software Version YER 03 00 79 Software Model 4 Port Gateway Description WireSpeed Data Gateway Boot Loader VER 03 00 79 Configuration 096 900078 004 Version of Application Software Configuration Proprietary configuration number of this device 030 300500 Rev A 38 October 2006 Ww WESTELL User Guide VersaLink Gateway Model 327W 12 CONFIGURATION At Discover Better Broadband Home Status Configuration Maintenance Troubleshooting Help Single Static IP Services Firewall Wireless Advanced LAN Advanced WAN Basic Security MAC Filter Advanced 12 1 Single Static IP Single IP Address PassThrough The following settings will be displayed if you select Single Static IP from the Configuration menu The Single Static IP Configuration screen allows you to select the device on your LAN that will share your Single Static IP Before you begin this section configure your PC settings to obtain an IP address from your Gateway automatically Refer to your Windows Help screen for instructions NOTE Single Static IP SSD allows the user to share the WAN assigned IP address with one device on the LAN By doing this the device with the SSI becomes visible on the Internet Network Address Translation NAT and Firewall rules do not apply to the device configured for SSI If you are using Bridge Routed Bridge prot
117. nated You may terminate this License Agreement at any time by returning the SOFTWARE and all copies thereof and extracts there from to Licensor Licensor may terminate this License Agreement upon the breach by you of any term hereof Upon such termination by Licensor you agree to return to Licensor the SOFTWARE and all copies and portions thereof 5 Limited Warranty Licensor warrants for your benefit alone for a period of 90 days from the date of commencement of this License Agreement referred to as the Warranty Period that the SOFTWARE CD in which the SOFTWARE is contained are free from defects in material and workmanship Licensor further warrants for your benefit alone that during the Warranty Period the SOFTWARE shall operate substantially in accordance with the functional specifications in the User s Manual If during the Warranty Period a defect in the SOFTWARE appears you may return the SOFTWARE to Licensor for replacement You agree that the foregoing constitutes your sole and exclusive remedy for breach by Licensor of any warranties made under this Agreement 030 300500 Rev A 156 October 2006 WESTELL User Guide VerrsaLink Gateway Model 327W EXCEPT FOR THE WARRANTIES SET FORTH ABOVE THE SOFTWARE CD AND THE SOFTWARE CONTAINED THEREIN ARE LICENSED AS IS AND LICENSOR DISCLAIMS ANY AND ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS F
118. nless your Internet Service Provider instructs you to change them 030 300500 Rev A 93 October 2006 Ww WESTELL User Guide VersaLink Gateway Model 327W If you have made any changes to your VC settings you need to save them To save the new VC settings click on OK when asked Set this PPPoE VC configuration If you click on cancel the new VC settings will not be saved If you clicked on OK in the preceding pop up screen the following pop up screen will appear VersaLink must be reset to allow the new configuration to take effect Click OK Microsoft Internet Explorer The modem must be reset in order for the new configuration to take affect Do vou wish to reset now If you clicked OK in the preceding screen the following screen will be displayed VersaLink will be reset and the new configuration will take effect File Edit View Favorites Tools Help da cl Links 2 DEE eg Discover Setter Broadband Home Status Configuration Maintenance Troubleshooting Help Resetting Modem Please Wait The modem is resetting in order for the requested changes to take effect Your page will be reloaded shortly 4 i b Done e Internet 7 After a brief delay the home page will be displayed Confirm that you have a DSL sync and that your PPP session displays UP Click on the connect button to establish a PPP session 030 300500 Rev A 94 October 2006 WESTELL User Guide VersaLink
119. nostics Logs screen ZA Diagnostic Logs Microsoft Internet Explorer De Edit View Favorites Tools Help Address http 4 1 92 168 1 1 diagLog htm At GE Discover Setter Broadband Home Status Configuration Maintenance Troubleshooting Help TT Date March 19 2004 Time 11 8 38 LOGS Select a log D Select a log All GOTT connection lfable savable format System Remote Logging Enable T Remote IP Address 192 168 1 47 030 300500 Rev A 136 October 2006 WESTELL User Guide VersaLink Gateway Model 327W If you clicked on All the following screen will be displayed This screen provides a detailed list of VersaLink s connection status and system information Click on clear diagnostic log to clear the diagnostic log information WESTELL EE Discover Better Broadband Home Status Configuration Maintenance Troubleshooting Help Date March 18 2004 Time 14 12 17 LOGS Select a log D All Entries CURRENT MODEM STATUS DSL Modem Status PPP Session Status no session Connection Type Time set from Time since last boot O days 1 hrs 34 mins 38 secs EVENTS SRR RR oR RR RRR RR RR RRR RRR RE oR Oo kt The first number is the Event time days hrs min sec since boot Events are listed starting from the most recent ETIKETT TEE TTT TEE TEE k k ak ak ak ak ak ak ak ak k k K k K AG k k k k ak ak ak ak ak ak of 0 0 0 20 US Atten 3 5 DS Atten 5 0 0 0 0 20 US Margin 5 0 DS Margin 15
120. nsure that it is permissible to be connected to the facilities of the local Telecommunication Company The equipment must also be installed using an acceptable method of connection The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations Connection to a party line service is subject to state tariffs Contact the state public utility commission public service commission or corporation commission for information If your home has specially wired alarm equipment connected to the telephone line ensure that the installation of this equipment Model 327W does not disable your alarm equipment If you have questions about what will disable alarm equipment consult your telephone company or a qualified installer If you experience trouble with this equipment Model 327W do not try to repair the equipment yourself The equipment cannot be repaired in the field and must be returned to the manufacturer Repairs to certified equipment 030 300500 Rev A 6 October 2006 WESTELL User Guide VersaLink Gateway Model 327W should be coordinated by a representative and designated by the supplier Refer to section 18 in this User Guide for further details The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed five Users should ensure for their own pr
121. oA Point to Point Protocol over ATM Asynchronous Transfer Mode PPPoE Point to Point Protocol over Ethernet Bridge Bridge Protocol Classical IPoA Internet Protocol over ATM Asynchronous Transfer Mode This is an ATM encapsulation of the IP protocol The protocol status VC x PPPoE Settings MRU Negotiation Factory Default DISABLED If ENABLED the Maximum Received Unit MRU would enforce MRU negotiations NOTE enable this option only at your Internet Service Provider s request Factory Default Enable If checked this option will disable the modem LCP Echo transmissions Indicates number of continuous LCP echo non responses received before the PPP session is terminated LCP Echo Retry Duration The interval between LCP Echo transmissions with responses LCP Echo Retry Duration The interval between LCP Echo after no response Tunneling Factory Default ENABLE If ENABLED this option allows PPP traffic to be bridged to the WAN This feature allows you to use a PPPoE shim on the host computer to connect to the Internet service provider by bypassing VersaLink s capability to do this NOTE Tunneling is available in PPPoE mode only NOTE The values for IP Address VersaLink DNS Primary and DNS Secondary are all Override of the values obtained from the PPP connection They default to 0 0 0 0 in which case the override is ignored Westell recommends that you do not change the values u
122. ocol Single Static IP configuration will not be available IMPORTANT Static NAT must be disabled before you can enable Single Static IP To disable Static NAT select Services from the Configuration menu Next click on the static NAT button Select the device from the Static NAT Device drop down menu and click on disable Return to Single Static IP Configuration by selecting Single Static IP Configuration from the Configuration menu Tj Singa Static Pi br Configuiation Mictocolt Internat UC aploer Dr L Sen Drais Jeck Help Biegle Gtoaitk IP Conflspratlgn Plaze zp nrt which devica will share your Sange Static IP if ther Configured PC selected a foc must be mamia configured to i ona GCn Dave he Sree Stobe JD adorer WAM IP Address 1722h a8 030 300500 Rev A 39 October 2006 We WESTELL User Guide VersaLink Gateway Model 327W 12 1 1 Enabling Single Static IP Single IP Address PassThrough Applicable for PPPoE Connections Only To enable Single Static IP select a device that will share your Single Static IP from the options listed in the window Click on enable NOTE The Single Static IP Configuration screen allows you to select the device on your LAN that will share your Single Static IP x Single Static IP lt br gt Configuration Microsoft Internet Explorer File Edit View Favorites Tools Help WES TELL Discover Better Broadband Home Status Configuration Maintenance Troubleshooting
123. ode Multi Mode T 1413 Mode G DMT Mode and G LITE Mode DSL Speed Kbits Sec The transmission rate that is provided by your Internet Service Provider ISP 030 300500 Rev A 140 October 2006 Pe WESTELL User Guide VersaLink Gateway Model 327W SNR Margin db The Signal to Noise Ratio S N where 0 db 1x10 which inhibits your DSL speed Line Attenuation dB The DSL line loss Transmit Power db Hz The transmitted signal strength 15 3 3 WAN VC Statistics The following settings will be displayed if you select WAN VC from the Statistics menu NOTE If VersaLink is configured using ETHERNET PORT 1 the following screen will not be available WAN YC Statistics Microsoft Internet Explorer File Edit View Favorites Tools Help a WES TELL E Discover Setter Broadband Home Status Configuration Maintenance Troubleshooting Help WAN C Statistics Packet Information VPI VCI In Errors In Discard Packets In Non Unicast Packets In Unicast Packets In Octets Out Errors Out Discard Packets Out Non Unicast Packets Out Unicast Packets Out Octets MTU Interface Type Interface Description PPP CONNECTION Out Errors The number of non Unicast packets transmitted on the ATM port 030 300500 Rev A 141 October 2006 Pe WESTELL User Guide VersaLink Gateway Model 327W 15 4 Wireless Statistics The following settings will be displayed if you select Wireless from the Stati
124. ol See Advanced WAN section for configuring VC s refer to section 12 6 5 E YLAN Configuration Microsoft Internet Explorer File Edit View Favorites Tools Help Address http dslrouter cos htm At WESTELL Discover Better Broadband Home Status Configuration Maintenance Troubleshooting Help YLAN Configuration VLAN Enable LAN Configuration LAN Port EthemetPort1 zl VLAN ID D VLAN Priority EE Outgoing LAN Tag REMOVE sl D NOTE If you change the values in the VLAN Configuration screen and click the reset button the screen will display the previously set values for the LAN Port you have selected If you change the settings in this screen you must click save to save the new settings If you click on save the following pop up screen will appear Click OK in the pop up screen to allow the new settings to take effect Microsoft Internet Explorer E4 2 Save and configure COS Cancel 030 300500 Rev A 84 October 2006 WESTELL User Guide VersaLink Gateway Model 327W 12 6 Advanced WAN This section explains the configurable features of VersaLink that are available if you select Advanced WAN from the Configuration menu NOTE If VersaLink is configured for ETHERNET PORT 1 QOS will not be displayed You must configure VersaLink for DSLATM PORT to access QOS in the Advanced WAN drop down menu Refer to section 12 6 2 1 for details WES TELL Discover Better Broadb
125. on factory default 030 300500 Rev A 123 October 2006 Pe VWESTELL User Guide 14 2 Firewall Log VersaLink Gateway Model 327W The following settings will be displayed if you select Firewall Log from the Maintenance menu This screen is an advanced diagnostics screen It alerts you of noteworthy information sent to VersaLink from the Internet The screen can contain 1000 entries but a maximum of 50 entries are displayed at a time Once 1000 entries have been logged the oldest entry is removed to make space for the new entries as they occur The following settings are displayed 3 Firewall log Microsoft Internet Explorer Ele Edt View Favorites Tools Help a WESTELL Discover Better Broadband Home Status Configuration Maintenance Troubleshooting Help Firewall lo Packet Date 1 Clear log Printable savable format Rule Reason 030 300500 Rev A 0 Day s 0 Day s 0 Day s 0 Day s 0 Day s 0 Day s 0 Day s GD Gin E Time 00 09 09 00 08 57 00 08 51 00 08 48 00 00 37 00 00 37 00 00 37 Direction Source Outbound Outbound Outbound Outbound Inbound Inbound Inbound Rule Reason RulesDrop RulesDrop RulesDrop RulesDrop PcktOfCurrentSession PcktOfCurrentSession PcktOfCurrentSession Selecting this button removes all entries from the log Selecting this button opens a new window that contains a list of all the logged packets that can be s
126. ons Games and VPN specific programs The following chart provides protocol information for the services supported by VersaLink NOTE To configure VersaLink for a service or application follow the steps in section 13 Setting Up Advanced Service Configuration of this User Guide Applications Games VPN Support 2611 2612 TCP 6667 TCP 6500 UDP 27900 UDP 4000 TCP 6112 TCP UDP 3000 UDP 5190 TCP Calista IP Phone 3000 UDP 5190 TCP DeltaForce Land Warrior UDP 53 TCP 21 TCP 7430 TCP 80 UDP 1029 UDP 1144 UDP 65436 UDP 17478 2600 UDP 27500 UDP 27910 UDP 27960 UDP F 16 Mig 29 3863 UDP F 22 Lightning 3 4660 4670 TCP UDP 3875 UDP 4533 4534 UDP 4660 4670 UDP F 22 Raptor 3874 3875 UDP Fighter Ace II 50000 50100 TCP UDP Fighter Ace II for DX play 50000 50100 TCP UDP 47624 TCP 2300 2400 TCP UDP 030 300500 Rev A 150 October 2006 a WESTELL User Guide VersaLink Gateway Model 327W Application Game Port Protocol GameSpy Online UDP 3783 UDP 6515 TCP 6667 UDP 12203 TCP UDP 13139 UDP 27900 UDP 28900 UDP 29900 UDP 29901 Ghost Recon TCP 80 UDP 1038 UDP 1032 UDP 53 UDP 2347 UDP 2346 GNUtella 6346 TCP UDP 1214TCP e TCP UDP 1214 TCP a Life Server UDP client only 27015 UDP Heretic II Server 28910 TCP 26900 1 each player needs their own port Increment by one for each person HTTPS 443 TCP UDP ICMP Echo 4 ICMP ICQ OLD 4000 UDP 20000 20019 TCP ICQ 2001b 4099
127. otection that the electrical ground connections of the power utility telephone lines and internal metallic water pipe system if present are connected together This precaution may be particularly important in rural areas A CAUTION AN Users should not attempt to make such connections themselves but should contact the appropriate electrical inspection authority or electrician as appropriate 030 300500 Rev A 7 October 2006 a WESTELL User Guide VersaLink Gateway Model 327W 4 NETWORKING REQUIREMENTS The following system specifications are required for optimum performance of the VersaLink via 10 100 Base T or Wireless installations CONNECTION TYPE MINIMUM SYSTEM REQUIREMENTS REM Pentium or equivalent class machines Networking via 10 100 Microsoft Windows 95 98 ME 2000 NT 4 0 or Base T Ethernet XP Macintosh OS X or Linux installed requires an available 64 MB RAM 128 MB recommended Ethernet port with a 10 MB of free hard drive space 10 100 Base T Network TCP IP Protocol stack installed Interface Card NIC 10 100 Base T Network Interface Card NIC installed Computer Operating System CD ROM on hand Pentium or equivalent class machines Networking via Microsoft Windows 98 ME 2000 or XP or Wireless or other Macintosh OS X installed 802 1 1b g g capable Computer Operating System CD ROM on hand network adapter card Internet Explorer 4 x or Netscape Navigator 4 x or higher 64 M
128. provided mane for connection proie Account ID Provided by your FSP Account Password Provided by your FSP i nex reset Help Type in your account parameters Account parameters are required before connecting to the Internet Account Parameters include e Connection Name the Connection Name is a word or phrase that you use to identify your account You may enter up 64 characters in this field e Account ID the Account ID is provided by your Internet Service Provider You may enter up 255 characters in this field e Account Password the Account Password is provided by your Internet Service Provider You may enter up 255 characters in this field 030 300500 Rev A 18 October 2006 a WESTELL User Guide VersaLink Gateway Model 327W After you type your account parameters at the User Name screen they will be displayed as shown in the screen below Click next if you want your account parameters to take effect Click on reset if you do not want the account parameters to take effect or if you want to retype the parameters User Name Connection Name My Connection User provided name for cannecton profile Account ID jwestell local Provided by your IOP Account Password pee Type the VPI and VCI values 0 for VPI and 35 for VCI default you obtained from your Internet service provider The actual VPI VCI values may vary according to your ISP Click on next VPI VCI vPI 0 255 P lt
129. r 2 Save and reconfigure DHCP IMPORTANT After you enable the DHCP server you must reboot your PC 030 300500 Rev A 76 October 2006 M WESTELL User Guide VersaLink Gateway Model 327W 12 5 5 Private LAN Configuration Configuring NAT The following settings will be displayed if you select Private LAN from the Advanced LAN menu Private LAN is the default configuration for this VersaLink NOTE Private LAN allows you to set up a network behind VersaLink If you change the settings in this screen click save If you click reset the changes will not take effect Private LAN Configuration Microsoft Internet Explorer Discover Better Broadband Home Status Configuration Maintenance Troubleshooting Help Private LAN Configuration Private LAN DHCP Server Enable W Private LAN Enable WV Modem IP Address 921681 1 Subnet Mask 255 255 255 0 Private LAN DHCP Settings DHCP Start Address 192 168 1 15 DHCP End Address 192 168 1 47 DHCP Lease Time fi lo fo 0 Days Hours Minutes Seconds e Ga If you made changes and clicked on save the following pop up screen will be displayed Click on OK This will save your Private LAN Configuration settings If you click Cancel your new settings will not take effect Microsoft Internet Explorer x A Load new Private LAN configuration Cancel Private LAN DHCP Server Enable Default CHECKED If this box is CHECKED it enables DHCP addresses to
130. r File Edit View Favorites Tools Help At Discover Better Broadband Home Status Configuration Maintenance Troubleshooting Help J WAN Configuration WAN PORT ETHERNET PORT1 Status Protocol Enabled PPPoE 030 300500 Rev A 108 October 2006 M WESTELL User Guide VersaLink Gateway Model 327W 12 6 7 QOS The following settings will be displayed if you select QOS from the Advanced WAN menu If you change any settings in this screen click on save If you click on reset this screen will refresh and display your last saved QoS configuration NOTE The QOS feature helps ensure data integrity in high speed transmissions QOS provides the capability to partition network traffic into multiple priority levels or classes of service After packet classification other QOS features can be utilized to assign the appropriate traffic handling policies including congestion management bandwidth allocation and delay bounds for each traffic class Discover Better Broadband Home Status Configuration Maintenance Troubleshooting Help 8 QOS Configuration QOS Enable Turbo TCP Enable QOS Configuration QOS Filter Enable EI QOS Classification Best Effort BE Peak Information Rate 100 Committed Information Rate la Peak Burst Size ms bm Committed Burst Size ms bm Max Queue Size bm Latency Measurements Latency Boundary Boundary 1 O0ms D Latency Threshold ms fo IP Fragmentation Enable IT IP
131. r Gateway s connection setting is set to Always On and you have changes any of these values the Gateway will reset automatically For instructions on editing your connection settings see section 10 2 The modem must be reset in order for the new configuration to take affect F Bo pou wish to reset now Cancel If you clicked OK in the pop up the following screen will be displayed VersaLink will be reset and the new configuration will take effect Next proceed to section 7 2 to confirm your DSL sync File Edit View Favorites Tools Help eg ES Discover Setter Broadband Home Status Configuration Maintenance Troubleshooting Help Resetting Modem Please Wait The modem is resetting in order for the requested changes to take effect Your page will be reloaded shortly e Openina page htto 192 168 1 1 indexHidden htm ai Intenet Z 030 300500 Rev A 21 October 2006 WESTELL User Guide VersaLink Gateway Model 327W 7 2 Confirming a DSL Syne Remember you must have active DSL service before VersaLink can synchronize with your ISP s equipment To determine if VersaLink has a DSL sync view the DSL Connection Rate in the Connection Overview section see the following Home page If the status reads No DSL Connection check the DSL physical connection explained in section 6 INSTALLING THE HARDWARE of this User Guide NOTE If no DSL sync is established the connection b
132. r WEP is DISABLED If you enable WEP you must ensure the network setting for your wireless adapter is set to Must Use Shared Key for WEP or Open Wi Fi You must ensure that your PC s Wi Fi adapter is configured properly for whichever network setting you use You can access the settings in the advanced properties of the wireless network adapter To network VersaLink to additional computers in your home or office using a wireless installation you will need to confirm the following 1 Ensure that an 802 11b g g wireless network adapter has been installed in each PC on your wireless network 2 Install the appropriate drivers for your Wireless EEE802 11b or IEEE802 11g adapter 3 Make sure the SMA antenna connector is loose Orient the antenna in the proper configuration Then tighten the antenna knob to lock it into place 4 Connect the power supply cord to the power connector marked DC 12V on the rear panel of VersaLink Plug the other end of the power supply into a wall socket and then turn on the modem 030 300500 Rev A 14 October 2006 WESTELL User Guide VersaLink Gateway Model 327W 5 Connect the DSL phone cable from the connector marked K on the rear panel of VersaLink to the DSL equipped telephone line jack on the wall IMPORTANT Do not use a DSL filter on this connection You must use the phone cord that was provided with the VersaLink kit 6 Check to see if the DSL LED 1s solid Green If the DSL LED is
133. r delds 5 addmss or TOPO pii united ofthe Ur header The from keyednd devignales the gbure felds and hele keent designates Ihe Gectination Dees One pr more A dasoripiors ofthe elds amd thelr te cantante then follies the kerani A lied of descnptars ig l ae SO porated Ire colons These Feld GeStriplons me lude we OF adds Mask Ketek meee 2 por TC or UDP Fong nurse dd Spacifies the spurt Or Seshndbor IP address feed and Comparison mask This k rp eg H folowed by a IP adres in doe dermal nelation and miaek ceparaled by a forevard alagh The mek re a number fram i lo 37 and E signtios hye mary tity ofthe E addmss am conmparnd tio mask is provided a mask vabas af is attuned port Epectios tet saurce ondesination WOPITCP pori number This keeeprd is follvenod br the 16 br port FE presented He gp ce decimal formal Wing fe or operators aw for meaithing on ranger ef ponz muiocmicnluwfnlrmeetsem eine Gpoprtez Dip value oi ip probe Geld arra in e P bhogor Ri folleg e 3 E atpmgier thai species the profiorel walas There are bulk in keen far ga TCP UDP OCP ang IOMP bminrels Ha Tire nl proil ilui s hh Ay be morang by 3 Datel or haa sca wilut Bien U ang 255 leg feecHesa fre TCP prolocal udp p je he UDF Gooi ral iomp Specties the CHP proeeal Kamp Spini he IGE Gro Taga ung zak pah lag la afi Specties poma r rbipabhnn ofthe flag Bita fund in he TOF header Tee Rarannidlors yei Tet kiei Should be reprenen in 3 Ooo d iwe
134. rily the same station but to any single station as opposed to a transmission that multiple stations would receive as in the case of broadcast message 030 300500 Rev A 142 October 2006 WESTELL User Guide VersaLink Gateway Model 327W OUT Multicast Frames The number of successfully transmitted frames whose destination address was a multicast address received by more that one station not necessarily broadcast to all stations but more than a single station Broadcast messages are included in the count OUT Fragments The number of successful transmissions made This will typically be greater than the sum of the Unicast and Multicast frames because large frames are broken into multiple transmissions The number of fragments per frame is based on the Fragmentation Threshold setting not user configurable OUT Frames after one or more The number of frames that successfully transmitted after more than one retries retry Any fragment of a frame that required multiple retries would increment this counter for the whole frame OUT Dropped Frames too many The number of frames that did not transmit due to the short or long retry retries limit being reached because no acknowledgement or CTS was received IN Unicast Frames The number of successfully received frames whose destination address was a single location not necessarily the same location but to any single location as opposed to the broadcast address multicast address Broadcast m
135. rocedure defined under the Maintenance menu in section 14 1 Factory defaults become current configuration If you select ETHERNET PORT 1 from the WAN Port drop down arrow the following screen will be displayed Click OK Microsoft Internet Explorer Ea AN This change will disable your DSL port The WAN interface will be changed to ethernet port 1 030 300500 Rev A 90 October 2006 A WESTELL User Guide VersaLink Gateway Model 327W If you click on OK in the preceding pop up screen the following screen will be displayed Click on OK If you click on Cancel the change will not take effect Microsoft Internet Explorer E4 2 Arte you sure you wish to change your WAN port and disable DSL Cancel If you clicked on OK in the preceding pop up screen the following pop up screen will appear VersaLink must be reset to allow the new configuration to take effect Click on OK Microsoft Internet Explorer The modem must be reset m order for the new configuration to take affect Dio vou with to reset now If you clicked on OK in the preceding screen the following screen will be displayed VersaLink will be reset and the new configuration will take effect File Edit View Favorites Tools Help fa Links ze EBM At WESTELL ver Better Broadband Home Status Configuration Maintenance Troubleshooting Help Resetting Modem Please Wait The modem is resetting in order for the req
136. roubleshooting Help Resetting Modem Please Wait The modem is resetting in order for the requested changes to take effect Your page will be reloaded shortly 4 4 b Done i ES e Intemet After a brief delay the home page will be displayed Confirm that you have a DSL sync and that your PPP session displays UP Click on the connect button to establish a PPP session 030 300500 Rev A 47 October 2006 Pe WESTELL User Guide VersaLink Gateway Model 327W 12 2 2 Creating a New NAT Service Profile NAT Profiles allow you to create specific service settings The NAT profile may then be associated with a connection profile allowing you to customize profiles for specific users For example if you want to attach specific NAT services to a profile or if you want to set up a different connection setting for a profile you can create new NAT profiles and customize them to your preference NOTE You may create up to four NAT profiles and attach an unlimited number of services to each profile To create anew NAT profile click new in the Service Configuration screen E Service Configuration Microsoft Internet Explorer Fie Feb Vun Facette Teck Help Miisa bie ISS A 8 1 Level Mem WESTELL aner etter Bresanand Home Statue Configuration Maintenance Troubleshooting Help Service Conflguratlon m Gum Currant Profle Default NM Service Mane Desaters Gusto Serve UPNP Enable
137. rsaLink to the DSL equipped telephone line jack on the wall IMPORTANT Do not use a DSL filter on this connection You must use the phone cord that was provided with the kit CO 6 Connect the yellow Ethernet cable from any one of the Ethernet jacks marked SES on the rear panel of VersaLink to the Ethernet port on your computer Repeat this step to connect up to three additional PCs to VersaLink NOTE You may connect to any of the four Ethernet jacks on the rear panel as they serve as an Ethernet switch However when using the optional uplink port E1 Ethernet LAN connection is limited to ports E2 E3 and E4 7 Check to see if the DSL LED is solid green If the DSL LED is solid green VersaLink is functioning properly 8 Check to see if the Ethernet LED 1s solid green Solid green indicates that the Ethernet connection is functioning properly 9 Check to see if VersaLink s Wireless LED is solid green This means that the Wireless interface 1s functioning properly Congratulations You have completed the simultaneous hardware Ethernet and Wireless installation You must now go to section 7 to configure VersaLink for Internet connection 030 300500 Rev A 16 October 2006 Pe WESTELL User Guide VersaLink Gateway Model 327W 7 CONFIGURING VERSALINK FOR INTERNET CONNECTION To browse the Internet using VersaLink you must set up your account profile confirm your DSL sync and establish a PPP session with your
138. s Configuration Maintenance Troubleshooting Help Current Profile Default Seioc A Senice 7 Denotes Custom Service UPNP Enable Service Name 5 fervice Nama Service Mode Host Douce your fiareall te enabled phe Grgoseall mole Laky precedvace over Lee Services i ere Dine CUSTOM Service static HAT 030 300500 Rev A 122 October 2006 WESTELL User Guide VersaLink Gateway Model 327W 14 MAINTENANCE ELL oo er Broadband Home Status Configuration Maintenance Troubleshooting Help Backup Restore Firewall Log Administrative Password Remote Access Update Device 14 1 Backup Restore The following settings will be displayed if you select Backup Restore from the Maintenance menu NOTE Backup settings are stored in a separate area of flash not to an external backup source SI Backup Restore Microsoft Internet Explorer File Edit View Favorites Tools Help PS WES TELL Nd Discover Better Broadband Home Status Configuration Maintenance Troubleshooting Help Backup Restore Current configuration becomes Backup configuration Back up Backed up configuration becomes Current configuration Factory defaults becomes Current configuration Select this button if you want to store all of the current configuration data such Backup Configuration that it can be recalled later becomes Current configuration configuration parameters and make these values current Current configurati
139. ser Guide VersaLink Gateway Model 327W If you click on OK in the preceding pop up screen the following pop up screen will be displayed Click on OK If you clicked on OK the following screen will be displayed VersaLink will be reset and the new configuration will take effect kd EE EE Discover Better Broadband Home Status Configuration Maintenance Troubleshooting Help Resetting Modem Please Wait The modem is resetting in order for the requested changes to take effect Your page will be reloaded shortly 030 300500 Rev A 104 October 2006 M User Guide VersaLink Gateway Model 327W After the Gateway has been reset from the Configuration menu select Advanced WAN and then select WAN The following screen will be displayed E WAN Configuration Microsoft Internet Explorer File Edit View Favorites Tools Help Discover Setter Broadband Home Status Configuration Maintenance Troubleshooting Help _ WAN Configuration WAN PORT ETHERNET PORT 1 Status Protocol Enabled PPPoE If you click edit the following screen will be displayed By using this screen you can configure the WAN Ethernet port settings of your Gateway WAN Ethernet Configuration Protocol PPPoE Status Enabled PPPoE Settings IP Address unn gt gt Gateway unn gt DNS Primary unn gt DNS Secondary unn Subnet Mask MRU Negotiation M LCP Echo Disable T LCP Echo Failures e ust De betw
140. splayed Click OK to save the new settings If you click on Cancel your new settings will not take effect Microsoft Internet Explorer 7 Load new Public LAN configuration Cancel NOTE DHCP Lease Time value must be greater than 10 seconds The default 01 00 00 00 Seconds must be between 0 and 59 minutes must be between 0 and 59 and hours must be between 0 and 23 If the settings you have entered in the Public LAN Configuration screen are incorrect the following warnings messages may be displayed via pop up screens If this occurs check settings in the Public LAN Configuration screen Warning Message Check Public LAN DHCP Settings Start Address is not part of the Subnet Check the value in the DHCP Start Address field End Address is not part of the Subnet Check the value in the DHCP End Address field End Address is below the Start Address Check the value in the DHCP End Address field Lease time must be greater than 10 seconds Check the values in the DHCP Lease Time fields 030 300500 Rev A 81 October 2006 WESTELL User Guide VersaLink Gateway Model 327W Seconds must be between 0 and 59 Check the Seconds field at DHCP Lease Time Minutes must be between 0 and 59 Check the Minutes field at DHCP Lease Time Hours must be between 0 and 23 Check the Hours field at DHCP Lease Time If you clicked on OK in the Load new Public LAN configuration screen the following pop up screen will be displayed This will
141. ssssssssssssssseererresssssssssssssssssseeeeerssss 39 EE 44 12 Firewall RE soar se serernctaxeeserietaisatcttnisid cada actsereaerannnieruisteeboaeuidatitenttsaasatiadadicnisuotwaasiaebioutmnatesetasenesmbseetdsts 56 IS VY he SC o WEE 60 030 300500 Rev A 2 October 2006 Pa MESS TELL User Guide VersaLink Gateway Model 327W 123 Adyanced LAN RE 69 D TNC N A RE 85 13 SETTING UP ADVANCED SERVICE CONPIOGURATION ccececccceessssnnneeeeeeeeeeeeeeeeseeeeeesnsnaaeeeeeeeeeeeeees 115 13 1 Port Forwarding Ranges of Ports s2aiccsc cossssasaneaseseaneasanacetacegapesnaagaontasnaaseconngesansamnscaadapntassaanesentaanscinegesuios 116 13 2 Adding Port Forwarding POTIS sn crcecencssncevicstouaPanstesassasrcecsnedsadtssaevnendoncteeadaaumsodeuestasevanetnsademstiqntsbocuvnesSexane 116 Lr POPON d kg PO EN 117 4 Adding Local Taig Sei EE 118 Doa E Tr E E sede qenoveneumeteetaaentstdardenuaioqesteneneanacess eeareners 119 Peo Ee WEE 120 l3 7 Disabling Statie IN ALP E 121 e UN TINO EIN ANCE ea E E E E E E E AEE E E E E E A 123 14 1 Back p RestOre ais inessetecsivopswtient ne tarveneuemedensneseyeusuanwiiewe rr N euE NE eR EK EEEE EEEN EER ENEE N EEEE E EEan aaaea 123 lA Pie w AUN EOS eeen E E E E E E T 124 14 3 Administrative Password WE 126 Ek EE 127 Aoa A TC ye ee E EE E 128 15 KEE EES L E ER E 133 MY SMA Ne bE IC EE 133 es BCS e Ie os eee tne eee ee mere enn ever ret en oe entre E rte eee re meer creer Teeter rete 135 De AUIS CS E E vanes asses Ge
142. stics menu 4 Wireless Statistics Microsoft Internet Explorer Fie Edit View Favorites Tools Help Dm Discover Better Broadband Home Status Configuration Maintenance Troubleshooting Help Wireless Statistics Wireless Card Information Network Name SSID 00001 802 11 MAC Address BSSID 00 e0 98 b8 cc e7 FW version Rev 0 1 0 11 Communication Statistics Unicast Frames Multicast Frames Fragments Frames after one or more retries Dropped Frames Network Name SSID This string 32 characters or less is the name associated with the Access Point AP To connect to the AP the Service Set ID SSID on a Station card must match the SSID on the AP 802 11 MAC Address BSSID This is the Media Access Controller address of the AP It is used as the Basic Service Set Identifier BSSID FW Version This is the Network Interface Card Identifier It uniquely identifies the hardware platform of the AP This is used with other information to determine if the inserted card can be used as an AP and if so the version of AP firmware to be used Not all makes of wireless station cards can be used as an AP NOTE Data preceded by OUT pertain to transmissions from the VersaLink to a station VersaLink is the source Data preceded by IN pertain to data received by VersaLink VersaLink is the destination OUT Unicast Frames The number of successfully transmitted frames whose destination address was a Single station not necessa
143. t Service Configuration from the Configuration screen 2 Click the UPNP Enable box a check mark will appear in the box 3 Follow the instructions in the pop up screens 4 Click OK to Reset the Gateway NOTE When you are ready to disable UPNP uncheck the UPNP Enable box in the Service Configuration screen If you click the UPNP Enable box in the Service Configuration screen a check mark will appear in the box and the following pop up screen will be displayed Click on OK Microsoft Internet Explorer x a K Do you wish to save this UEND configuration Cancel If you clicked OK in the preceding screen the following pop up screen will be displayed Click on OK to reset the Gateway Microsoft Internet Explorer x K The modem must be reset in order for the new configuration to take affect Do you wish to reset now Cancel NOTE To use the UPNP functionality in Versalink your Windows XP operating system must also support UPNP Please contact your computer manufacturer to verify that UPNP is enabled in your Windows XP operating system 030 300500 Rev A 46 October 2006 M User Guide VersaLink Gateway Model 327W If you clicked OK in the preceding screen the following screen will be displayed The Gateway will be reset automatically and the new configuration will take effect File Edit View Favorites Tools Help a Discover Better Broadband Home Status Configuration Maintenance T
144. t account profile After you select the default profile click the static NAT button NOTE In the following screen the default account profile is labeled Default However if you have renamed the default account profile you must select the profile name you created as the default profile WESTELL Hert Status Configuration Maintenance Troubleshooting Help Aorvior Copnflemrrot bumn nm eum Currant Profile Det we L tsch E SS Ss Denoiez Gurion Savea UPHP Enable I Sarvlon Mama Sarvics Mada Host Devine pour fnna re nabied fhe Areal rugs tate precedence oar ie Zen c e dealing custom service static RAT If you click on the static NAT button in the Service Configuration screen the following screen will be displayed Select your device from the Static NAT Device drop down arrow or type the IP address of the device in the field labeled IP Address Click on enable This will automatically enable the Static NAT feature for that device Static NAT Microsoft Internet Explorer a Static NAT Set Up an IP Address to be your Default NAT Destination Static NAT Device tmabb xp EI or specify IP Address All unsolicited inbound traffic wil be sent to the above device Note Static Nat and IP Passthrough are mutually exclusive features enable disable cancel 030 300500 Rev A 120 October 2006 M WESTELL User Guide VersaLink Gateway Model 327W If you click ena
145. ternet Explorer Simi EZ Software Upgrade Click browse to select the upgrade file Then start the transfer by clicking the upload file button Upgrade File A Software Update Files Browse Upload file Help 030 300500 Rev A 130 October 2006 Ww WESTELL User Guide VersaLink Gateway Model 327W This screen shows that the file is being uploaded to VersaLink 3 WireS peed Dual Connect Upgrade Software Microsoft Internet Explorer Simi E3 Software Upgrade Click browse to select the upgrade file Then start the transfer by clicking the upload file button Upgrade File A Software Update Files Browse 4 eooo TT TTT a Uploading File The screens below show that the file upload has completed and that the Programming Flash is being erased to prepare the Flash storage area for upload of the new file Programming Flash is a temporary storage area for uploaded files J WireSpeed Dual Connect Upgrade Software Microsoft Internet Explorer Mi E3 WireS peed Dual Connect Upgrade Software Microsoft Internet Explorer i l E3 Software Upgrade Software Upgrade Click browse to select the upgrade file Click browse to select the upgrade file Then start the transfer by clicking the upload file button Then start the transfer by clicking the upload file button Upgrade File Browse Upgrade File Browse Upload file Upload file Help Help Uploading File Up
146. the Protocol for each VC which is specified by your Service Provider Possible Response NOTE The configuration PPPoA Point to Point Protocol over ATM Asynchronous Transfer Mode specified by your Service PPPoE Point to Point Protocol over Ethernet Provider will determine which Bridge Bridge Protocol Protocols are available to you Classical IPoA Internet Protocol over ATM Asynchronous Transfer Mode This is an ATM encapsulation of the IP protocol Bridge Broadcast Factory Default CHECKED When this setting is CHECKED VersaLink will allow Broadcast IP packets to from the WAN When this setting is NOT CHECKED VersaLink will block Broadcast IP packets to from the WAN This setting is only valid if one of the Virtual Channels is configured for Bridge mode Bridge Multicast Factory Default CHECKED When this setting is CHECKED VersaLink will allow Multicast IP packets to from the WAN When this setting is NOT CHECKED VersaLink will block Multicast IP packets to from the WAN This setting is only valid if one of the Virtual Channels is configured for Bridge mode Spanning Tree Protocol Factory Default DISABLED Spanning Tree Protocol is a link management protocol that provides path redundancy while preventing undesirable loops in the network For Ethernet network to function properly only one active path can exist between two stations When ENABLED two bridges are used to interconnect the same two computer network segments Spann
147. there are any associated stations than do not support ERP a protection algorithm is used to prevent contention Dynamic Similar to local STA s with the following extension The ERP protection setting 1s also dependent on Beacon frames from overlapping BSS IF Beacon frames are received that indicate ERP is not supported then a protection algorithm is used Enhanced Dynamic Similar to Dynamic with the following extension If associated stations that do not support ERP do not transmit for a period of time then protection algorithm is not used Rate Adaptation Factory Default Enable If disabled the highest rate shared between VersaLink and STA is used for each transmission Rate Fallback Factory Default After 1 Retry The number of retries to attempt before falling back to the next lower rate If Fallback is disabled the starting rate is the only rate tried IF Rate Adaptation is also disabled the maximum rate shared with the STA is always the starting rate and the only rate tried This may not work in noisy environments and will reduce roaming distances Possible Response After Retry Disable After 1 Retry After 2 Retry 802 11b Rates Mbps These are the allowable communication rates that VersaLink will attempt to use 802 11g Rates Mbps The rates are also broadcast within the connection protocol as the rates supported by VersaLink 030 300500 Rev A 68 October 2006 WESTELL User Guide VersaLink Gateway Model 327W 1
148. ting Table Destination Netmask Gateway Metric RIP Network Routing Table Indicates Network routes received via RIP RIP Host Routing Table The Host routes received via RIP Destination The destination IP address of the route Netmask The IP mask of the route Gateway The gateway of the route Metric The RIP metric 0 15 A lower value is better 030 300500 Rev A 146 October 2006 User Guide VersaLink Gateway Model 327W 15 5 4 QOS Status The following settings will be displayed if you select QOS from the Status menu Click on the clear button to clear all counts and statistics not just latency counts This does not affect the configuration values NOTE QoS must be enabled on the Gateway for this table to be populated WESTELL Discover Better Broadband QOS Status Total Dropped Total Enqueued Current Deepest Packets Packets Depth Depth Qos Filter Statistics Peak Total et Ave Committed Peak Total Total S DSL pkt Queue Info Committed Filter Info Rate Burst Packets Marked Bytes rate Number Rate k per per aia 5 pkt second 100 1000 1000 0 0 100 1000 1000 100 1000 1000 100 1000 1000 100 1000 1000 100 1000 1000 100 1000 1000 Con ms Burst MS Received Packets Qos Latency Counts Queue Not Time Omsto 10 ms to 20 ms to 40 ms to 100 ms to 1000 ms to Larger than Number Stamped 10 ms 20ms 40ms 100 ms 1000ms 3000ms 3000 ms 0 0 0 0 0 0 0 0 030 300500 Rev A 147 October 2006 Pa WESTE
149. u change any of the Status configurations a pop up screen will prompt you to reset the Gateway After the Gateway has been reset the Status configurations will take effect The edit button allows you to change the VC configuration settings of the Gateway Details on the edit button are explained later in section 12 6 3 NOTE The actual information displayed in this screen may vary depending on the network connection established E WAN Configuration Microsoft Internet Explorer File Edit View Favorites Tools Help LA Gs Discover Better Broadband Home Status Configuration Maintenance Troubleshooting Help WAN Configuration WAN PORT DSLATM PORT Status YPI VCI Protocol Enable 0 36 PPPoE Disable zl 0 43 Bridge Disable 0 37 Bridge Disable 9 38 Bridge Disable 9 39 Bridge Disable 9 40 Bridge Disable 0 41 Bridge Bridge Broadcast Iv Bridge Multicast Iv Spanning Tree Protocol Save filter settings 030 300500 Rev A 86 October 2006 WESTELL User Guide VersaLink Gateway Model 327W Factory Default DSLATM PORT Possible Responses Kee DSLATM PORT ETHERNET PORT 1 Allows you to enable or disable your VC Virtual Connection yE Displays the VPI Virtual Path Indicator value for a particular VC which is VPI i defined by your Service Provider Displays the VCI Virtual Channel Indicator value for a particular VC which is defined by your Service Provider Protocol Displays
150. uested changes to take effect Your page will be reloaded shortly ma a After VersaLink has been reset the DSL LED will be OFF This is because the DSL transceiver has now been disabled However the Power Ethernet and Wireless LEDs will remain lit 030 300500 Rev A 91 October 2006 WESTELL User Guide VersaLink Gateway Model 327W 12 6 3 Editing the WAN Configuration The following VC 1 Configuration screen will be displayed if you click on the edit button adjacent to any of the Enabled protocols displayed in the WAN Configuration screen NOTE The Protocol must be enabled before you can edit its VC configuration The VC 1 Configuration screen allows you to edit your virtual connection VC A virtual connection identifies a connection through the service provider s ATM network to your ISP Unlike physical hardware connections virtual connections are defined by data If you change any of the VC settings in the following screen click on the Set VC button NOTE If you experience any problems please reset VersaLink via the external hardware reset button or via the procedure defined under the Maintenance menu in section 14 1 The actual information displayed in this screen may vary depending on network connection established VC 1 Configuration vibo WET 35 DCH 100 Qos UBR Protocol PPPoE Status Enabled VC 1 PPPoE Settings IP Address 0000 Gateway 0 0 0 0 DNS Primary 0 0 0 0 ONS
151. uipment does cause harmful interference to radio or television reception which can be determined by turning the equipment OFF and ON the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and the receiver Connect the equipment to a different circuit from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Modifications made to the product unless expressly approved by Westell Inc could void the users right to operate the equipment RF EXPOSURE This device has been tested and complies with FCC RF Exposure SAR limits in typical laptop computer configurations and this device can be used in desktop or laptop computers with side mounted PCMCIA slots which can provide 1 cm separation distance from the antenna to the body of the user or a nearby person Thin laptop computers may need special attention to maintain antenna spacing while operating This device cannot be used with handheld PDAs personal digital assistants Use in other configurations may not ensure compliance with FCC RF exposure guidelines This device and its antenna must not be co located or operate in conjunction with another antenna or transmitter PART 68 COMPLIANCE REGISTRATION This equipment Model 327W complies with Part 68 of the FCC rules and the requirements adopted by t
152. um N ese neues INE N E E NE N I eee eee T 139 che EE a S A A E E 142 e ERE E RE E A PAN A RE E A PAN A A A E A E A E es 144 o NAT ERICE oee a E E E A E E TAE E A EE 150 17 TECHNICACSUPPORT INFORMATION E 154 18 WARRANTY AND REPAIRS EE 154 19 PRODUCT EE 155 20 SOFTWARE LICENSE AGREEMENT ccccssssseesensscccccccessesssssssssncceceasacccceeeesesssesssssseeesssacecessssessssseees 156 SA GI RIETETeMELATCR II ER E 157 030 300500 Rev A 3 October 2006 a WESTELL User Guide VersaLink Gateway Model 327W 1 PRODUCT DESCRIPTION The Westell VersaLink Gateway provides reliable high speed Internet access to your existing small office phone line Your ADSL connection is always on ending the hassles of dial up modems and busy signals Installation is easy no tools no headaches Simply connect the hardware apply power and perform the simple software configuration for VersaLink and you are on the Internet VersaLink is capable of data rates hundreds of times faster than a traditional analog modem But unlike analog modems VersaLink allows you to use the same phone line for simultaneous voice fax communications and high speed Internet access eliminating the need for dedicated phone lines for voice and data needs VersaLink supports a variety of networking interfaces such as wireless 802 11b g g ADSL Ethernet and the following optional features VersaPort Alternate WAN uplink port Layer w 2 Q
153. utton will not be displayed in the following screen To determine if the DSL sync is established check VersaLink s DSL LED If the DSL LED 1s not solid green you do not have a DSL sync established Contact your ISP for further instructions Z Application image Microsoft Internet Explorer De Edit View Favorites Tools Help Discover Better Broadband Home Status Configuration Maintenance Troubleshooting Help Home Connection Overview DSL Connect Rate Down Up No DSL Connection Connection Name PPP Status My Connection DOWN profile editor Profile with the ls your default profile To make changes to your default profile click on the profile editor button 030 300500 Rev A 22 October 2006 M User Guide VersaLink Gateway Model 327W The following screen shows the DSL connection rate with values that indicate a successful DSL SYNC has been established The connection rate values represent the transmission speed of your DSL line The Gateway may take time to report these values Click on the Connect button to establish a PPP session NOTE VersaLink will handle transmission rates up to 8 Mbps Your actual DSL rates may vary depending on your Internet service provider Z Application image Microsoft Internet Explorer File Edit View Favorites Tools Help Discover Better Broadband Home Status Configuration Maintenance Troubleshooting Help F Home Connection Overview DSL Connect Rate Down Up 806
154. ve saved it to your NAT service profile the following screen will be displayed It shows which NAT service is active for the selected profile eg AE WESTELL Olecover Setter Groedbend Status Configuration Maintenance Troubleshooting Help Service Configuration Current Profile Oefault E Service Name SelectA Service Denotes Custom Service WPNP Enable O Service Name Service Mode Host Device Amor A Cep Port Forw ardaig 192 168 1 10 your firewall we nabod bie rewal mules Lake precedence over the Services Ghee ls 030 300500 Rev A 54 October 2006 Pe WESTELL User Guide VersaLink Gateway Model 327W If you select the details button in the Service Configuration screen the following screen will display the details of the selected NAT service If you click on the delete button in the Service Configuration screen you will remove that NAT service from your NAT service profile Click close to continue 4 Service Details Microsoft Internet Explorer Service Details Service Name America Online Type Port Forwarding Port 1 Protocal TCP Global Portf s 5190 Base Host Port 5190 close NOTE If you would like to set up additional Advanced Service Configuration options refer to section 13 Setting Up Advanced Service Configuration 030 300500 Rev A 55 October 2006 WESTELL User Guide VersaLink Gateway Model 327W 12 3 Firewall Configuration The following settings will be disp
155. vices dafine custom service If you click enable the following pop up screen will be displayed If you click OK you will allow incoming connections to be forwarded to a designated local PC If you click Cancel you will allow only outgoing connections from any local PC Click OK or click Cancel NOTE If you click Cancel in the following pop up screen the NAT service you selected in the Service Configuration screen is still configured however it will not be assigned to any device on the local LAN You must click OK to host the NAT service Microsoft Internet Explorer E4 2 Host Serice Host will allow incoming connections to a designated local PL Dynamic will only allow outgoing connections from any local PC UK Host Cancel Dynamic Cancel 030 300500 Rev A 53 October 2006 M User Guide VersaLink Gateway Model 327W If you clicked OK in the preceding pop up screen the Host Device screen will be displayed The Host Device screen will allow you to select which device will host the NAT service you selected on your local area network You must either select the device from the Host Device drop down arrow or type an IP address in the field labeled IP Address If you click on Cancel the connection will be dynamically assigned Click on done E Host Device Microsoft Internet Explorer Host Device salle 982 D or specify ID Address one After you have selected a NAT service and you ha
156. y Default Disable If enabled VersaLink will send firewall logs to a syslog server Remote IP Address The IP address of the syslog server machine to which the diagnostics logs to be sent 030 300500 Rev A 56 October 2006 Pe WESTELL User Guide VersaLink Gateway Model 327W If you select Edit from the Security Level screen the User Defined Firewall Rules screen will be displayed This screen allows you to change the security parameters on your Inbound and Outbound Firewall rules via the User Defined Firewall Rules drop down arrow If you select Inbound this will restrict inbound traffic from the WAN to the LAN Outbound restricts outbound traffic to the WAN from the LAN To apply the new settings click Apply in the screen labeled User Defined Firewall Rules NOTE Westell recommends that you do not change the settings in the User Defined Firewall Rules screen If you need to reset VersaLink to factory default settings push the reset button on the rear of VersaLink The information displayed in the following screen depends upon the Firewall security setting you have selected If you selected None in the preceding Firewall Security Level screen no values will be displayed in the following User Defined Firewall Rules screen 3 Firewall Rules Microsoft Internet Explorer Pi fel xI File Edit View Favorites Tools Help e User Defined Firewall Rules inbound zl Security Level 1 IN rule sms Outbound Rul
157. your PCs hard drive or from update files stored on an Internet server NOTE The configurable settings of your Gateway may be erased during the update process E Update Device Microsoft Internet Explorer File Edit View Favorites Tools Help y Ger d E SE WES TELL E ZE Discover Better Broadband Home Status Configuration Maintenance Troubleshooting Help Update Device Update Device Update Status Unknown Current Version YER 03 00 50 Newer Version Unknown Issues Erratas bug information not available errata not available Status Last Update Check Performed unknown check for web update Web Update now local Update now Click on the check for web update button in the Update Device screen to check the web for possible software updates This screen will retrieve the software update file and display any available update information You must be connected to the Internet to use this option NOTE If you click on check for web update and the page returns a page not found message this indicates that the software update file is not available Go back to the previous screen to continue Click on the web update now button in the Update Device screen to download the software update file and automatically update the modem firmware if an update is available and applicable You must be connected to the Internet to use this option 030 300500 Rev A 128 October 2006 User Guide VersaLink Gateway

Westell Technologies Versalink 327W User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents