Wells WPP-10 User's Manual
Contents
1. WELLS MANUFACTURING COMPANY 2 3 2 2 ERIK CIRCLE P O Box 280 Verdi NV 89439 telephone 775 689 5700 fax 888 492 2783 www wellsbloomfield com OWNERS MANUAL MODEL WPP 6 WPP 10 POPCORN POPPER Includes INSTALLATION USE amp CARE SERVICING Model WPP 10 IMPORTANT DO NOT DISCARD THIS MANUAL This manual is considered to be part of the appliance and is to be given to the OWNER or MANAGER of the restaurant or to the person responsible for TRAINING OPERATORS of a this appliance Additional manuals are available from your WELLS DEALER THIS MANUAL MUST BE READ AND UNDERSTOOD BY ALL PERSONS USING OR INSTALLING THIS APPLIANCE Contact your WELLS DEALER if you have any questions concerning installation operation or maintenance of this equipment PRINTED IN CHINA p n 306223 Rev ECN 12645 M232 050824 cps Unless otherwise specified all commercial cooking equip ment manufactured by WELLS MFG is warranted against defects in materials and workmanship for a period of one year from the date of original installation or 18 months from the date of shipment from our factory whichever comes first and is for the benefit of the original purchaser only THIS WARRANTY IS THE COMPLETE AND ONLY WAR RANTY EXPRESSED OR IMPLIED IN LAW OR IN FACT INCLUDING BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICU LAR PURPOSE AND OR FOR DIRECT INDIRECT OR CONSEQUENTIAL DAMAGES IN C2. Properly connect kettle cord Does not pop popcorn receptacle Damaged kettle switch Replace kettle switch Damaged kettle internal components Replace kettle assembly Some brands of popcorn or popcorn that is out of date may not pop completely NOTE even the freshest example of the very Always use fresh quality popcorn Popcorn does not pop best brand may not always pop 100 of its completely kernels Press warmer switch to Press warmer switch to Stirrer misassembled or contaminated with built up cooking debris Clean stirrer components and reassemble properly Stirrer wand interfering with kettle tilt Position cam loose or damaged Reconnect or replace position cam Damaged position switch or wiring Repair wiring and or replace position switch Stirrer only rotates when kettle switch is No action required Kettle switch OFF Press kettle switch to Stirrer does not rotate Stirrer loose on gear drive shaft Reattach stirrer to gear drive shaft Stirrer motor damaged Replace motor and gear drive assembly CAUTION INJURY HAZARD Disconnect appliance from electrical power before performing any of these procedures POSITION SWITCH e LOCK NUT 4 NUT ___ _ GEAR DRIVE SHAFT Adjust Positioning Cam CAUTION BURN HAZARD Lamp may be hot Allow lamp to cool before replacing a LAMP GUARD Change Heat Lamp A
3. SIAUMO EZZ90 ZEZ 232 306223 Owners Manual WPP Series Popcorn Popper 23166 5 23168 LADLE 4 OZ 23167 LADLE 1 5 OZ 506671 CATCH MAGNETIC 506670 KNOB 506669 DROP DOOR 506668 CATCH TRAY 506658 506662 POSITION CAM RECEPTACLE KETTLE 506657 POSITION SWITCH 506663 SOCKET HEAT LAMP 506664 HEAT LAMP 120 506657 STIRRER MOTOR 120V 81756 WARMER SWITCH 81756 KETTLE SWITCH 506665 GUARD HEAT LAMP 506666 WARMER ELEMENT 120V 51217 STRAIN RELIEF 506667 CORDSET 120V 506659 KETTLE LID 506660 STIRRER ASSY 506661 KETTLE ASSY 120V amp 505951 i ____ ADJUSTABLE FOOT pk 4 KETTLE SOCKET see below for kettle HEAT LAMP SOCKET STIRRER MOTOR SWITCH FOR KETTLE AND STIRRER MOTOR SWITCH FOR HEAT LAMP AND BASE WARMER CONDUIT PLUG KETTLE BASE HEATER 10 daddog Jenueyy 2902 ZEZ 232 306223 Owners Manual WPP Series Popcorn Popper DESCRIPTION PART NO IMPORTANT Use only factory authorized service LADLE 1 5 oz 23166 parts and replacement filters LADLE 402 8197 For factory authorized SCOOP POPCORN 23168 service or to order factory authorized replacement parts contact your Well
4. such as servicing and NOTE For your protection please note that equipment in this shipment was carefully inspected and packaged by skilled personnel before leaving the factory Upon accep tance of this shipment the transportation company assumes full responsibility for its safe delivery IF SHIPMENT ARRIVES DAMAGED 1 VISIBLE LOSS OR DAMAGE Be certain that any visible loss or damage is noted on the freight bill or express receipt and that the note of loss or damage is signed by the delivery person 2 FILE CLAIM FOR DAMAGE IMMEDIATELY Regardless of the extent of the damage thorized personnel The prices charged by Wells Mfg Co for its products are based upon the limitations in this war ranty Seller s obligation under this warranty is limited to the repair of defects without charge by a Wells Mfg Co factory authorized service agency or one of its sub service agen cies This service will be provided on customer s premises for non portable models Portable models a device with a cord and plug must be taken or shipped to the closest au thorized service agency transportation charges prepaid for service In addition to restrictions contained in this warranty specific limitations are shown in the Service Policy and Pro cedure Guide Wells Mfg Co authorized service agencies are located in principal cities This warranty is valid in the United States and Canada and void elsewhere Please con sult your classified telephon
5. DJUST STIRRER NEUTRAL POSITION With the kettle switch OFF the stirrer should land at a position that allows the kettle to rotate without binding on the stirrer wand If the stirrer wand does not land positioned left to right adjust the positioning cam 1 Disconnect unit from electric power Remove the top panel Raise the kettle lid until it is captured by the magnetic holder Spin the gearmotor fan by hand until the stirrer wand is positioned left to right l e parallel to the front of the cabinet Loosen the positioning cam nut and locknut Turn the cam until it depresses the pin of the positioning switch Tighten the cam nut and lock nut Reconnect unit to electric power Press the kettle switch to ON Wait approximately 5 seconds then press the kettle switch to OFF The stirrer motor will run until the positioning cam activated the positioning switch If the stirrer wand stops in the proper left to right position procedure is complete Otherwise repeat steps 1 through 4 CHANGE HEAT LAMP 1 Press warmer switch OFF Allow unit to cool before replacing lamp Squeeze front and rear portions of guard until the front hook clears the slot Slide the rear hook from its slot then remove the guard Unthread old heat lamp from its socket and discard Thread new heat lamp into socket IMPORTANT Use only 400W safety coated lamp Reinstall guard
6. ONNECTION WITH WELLS MFG CO PRODUCTS This warranty is void if it is determined that upon inspection by an authorized service agency the equipment has been modified misused misap plied improperly installed or damaged in transit or by fire flood or act of God It also does not apply if the serial name plate has been removed or if service is performed by unau 1 Resetting of safety thermostats circuit breakers over load protectors and or fuse replacements are not covered by this warranty unless warranted conditions are the cause 2 All problems due to operation at voltages or phase other than specified on equipment nameplates are not covered by this warranty Conversion to correct voltage and or phase must be the customer s responsibility 3 All problems due to electrical connections made in accordance with electrical code requirements and wiring diagrams supplied with the equipment are not covered by this warranty 4 Replacement of items subject to normal wear to include such items as knobs light bulbs and normal maintenance functions including adjustments of thermostats adjustment of micro switches and replacement of fuses and indicating lights are not covered by warranty 5 Damage to electrical cords and or plug due to exposure to excessive heat are not covered by this warranty 6 Full use care and maintenance instructions supplied with each machine Noted maintenance and preventative maintenance items
7. UTION SHOCK HAZARD This appliance must be plugged into a properly installed and grounded electrical receptacle Sees IMPORTANT If an appropriate electrical receptacle is not readily accessible contact a licensed electrician to install the appropriate electrical receptacle 240 volt units are shipped without a power plug Contact a licensed electrician to install a power plug appropriate to local electrical codes IMPORTANT Damage due to being connected to the wrong voltage or phase is NOT covered by warranty UNPACKING amp INSPECTION Carefully remove the appliance from the carton Remove all protective plastic film packing materials and accessories from the appliance before connecting electrical power or otherwise performing any installation procedure Carefully read all instructions in this manual and the nstallation Instruction Sheet packed with the appliance before starting any installation Read and understand all labels and diagrams attached to the appliance Carefully account for all components and accessories before discarding packing materials Store all accessories in a convenient place for later use COMPONENTS Tray Drop Door Heat Lamp and Heat Lamp Guard Kettle Assembly and Kettle Lid Stirrer Wand and Stirrer Collar Scoop and 2 Ladles SETUP Setup the appliance only on firm level non combustible surface Verify local codes for requirements Concrete tile terrazzo or meta
8. amp and cabinet base heater will come on Preheat for kettle 7 minutes before popping the first batch Subsequent batches may be popped immediately Raise kettle lid up until it is captured by the magnetic holder Add measured amounts of popcorn kernels oil salt and flavoring to kettle Lower the kettle lid Close drop door and left plastic door Leave right plastic door partially open to access kettle knob POPPING POPCORN Press the KETTLE switch to ON Kettle will begin heating and stirrer will rotate Popped corn will lift the kettle lid then fall into the cabinet KETTLE switch may be left while refilling the kettle for subsequent cycles Shake unpopped kernels and husks from the kettle before refilling Continue popping corn until popcorn in the cabinet reaches the desired level Do not fill cabinet higher than the top of the drop door Press the KETTLE switch OFF The stirrer will continue to rotate until it achieves a neutral position Leave the WARMER switch ON SUGGESTIONS FOR USE Use the provided scoop to remove popcorn from the cabinet Stir popcorn in cabinet frequently to allow unpopped kernels and husks to fall through the debris grate into the tray If using all in one packets store a few packets for upcoming cook cycles in the cabinet under the popcorn so that oil and butter will be sufficiently melted to pour easily CAUTION HOT SURFACE Exposed surface
9. detergent Rinse by wiping with a sponge or soft cloth dampened with clear water Allow to air dry NOTE Baked on deposits may be removed with a plastic scouring pad DO NOT submerge kettle kettle cord or kettle plug in water Disassemble stirrer then slide kettle lid off of stirrer shaft Wipe lid and stirrer components with a sponge or soft cloth dampened with mild detergent Rinse by wiping with a sponge or soft cloth dampened with clear water Allow to air dry Wipe inside and outside of cabinet drop door and crumb tray with a sponge or soft cloth dampened with mild detergent Rinse by wiping with a sponge or soft cloth dampened with clear water Allow to air dry NOTES a Use when cleaning doors to prevent scratching b Do not wipe heat lamp if it is hot Use that no water is splashed into kettle receptacle or heat lamp socket Reinstall kettle lid Reassemble stirrer then reinstall kettle Reinstall drop door then slide crumb tray in place Procedure is complete daddog Jenueyy 2902 ZEZ 232 306223 Owners Manual WPP Series Popcorn Popper POSSIBLE CAUSE SUGGESTED REMEDY Power cord unplugged Plug power cord into appropriate receptacle No power to unit Circuit breaker tripped Reset circuit breaker Power cord or plug damaged Replace power cord assembly Kettle switch OFF Press kettle switch to plug ey securely plugged into twist
10. e directory your foodservice equipment dealer or write the Factory Service Department Wells Manufacturing Company P O Box 280 Verdi Ne vada 89439 phone 775 689 5700 or 888 492 2782 for information and other details concerning warranty cleaning schedules are customer responsibility Those miscellaneous adjustments noted are customer responsibility Proper attention to preventative maintenance and scheduled maintenance procedures will prolong the life of the appliance 7 Travel mileage is limited to sixty 60 miles from an Authorized Service Agency or one of its sub service agencies 8 All labor shall be performed during regular working hours Overtime premium will be charged to the buyer 9 All genuine Wells replacement parts are warranted for ninety 90 days from date of purchase on non warranty equipment This parts warranty is limited only to replacement of the defective part s Any use of non genuine Wells parts completely voids any warranty 10 Installation labor and job check outs are not considered warranty and are thus not covered by this warranty 11 Charges incurred by delays waiting time or operating restrictions that hinder the service technician s ability to perform service are not covered by warranty This includes institutional and correctional facilities 3 CONCEALED LOSS OR DAMAGE if damage is unnoticed until the merchandise is unpacked notify the transportation company or carrier immediate
11. icing requiring access to non insulated electrical components must be performed by a factory authorized technician DO NOT open any access panel which requires the use of tools Failure to follow this warning can result in severe electrical shock WARNING BURN HAZARD Kettle is extremely hot during operation To prevent burns always use the kettle knob to rotate or shake the kettle and always use the handle to lift the kettle lid CAUTION RISK OF DAMAGE DO NOT connect or energize this appliance until all installation instructions are read and followed Damage to the appliance will result if these instructions are not followed CAUTION HOT SURFACE Exposed surfaces can be hot to the touch and may cause burns This appliance conforms to NSF Standard 4 for sanitation only if installed in accordance with the supplied nstallation Instructions and maintained according to the instructions in this manual This appliance is listed by ETL STD 4 NOTE DO NOT discard the carton or other packing materials until you have inspected the appliance for hidden damage and tested it for proper operation Refer to SHIPPING DAMAGE CLAIM PROCEDURE on the inside front cover of this manual CAUTION RISK OF DAMAGE DO NOT connect or energize this appliance until all installation instructions are read and followed Damage to the appliance will result if these instructions are not followed CA
12. isconnect this appliance from electrical power before performing any maintenance or servicing DO NOT submerge this appliance in water This appliance is not jet stream approved Do not direct water jet or steam jet at this appliance or at any control panel or wiring Do not splash or pour water on in or over any controls control panel or wiring Exposed surfaces of this appliance can be hot to the touch and may cause burns The kettle and kettle lid will be extremely hot during operation and can cause serious burns on contact To prevent burns always use the kettle knob to rotate or shake the kettle and always use the handle to lift the kettle lid Heat lamp will be very hot when in use Contact will cause severe injury Do not operate this appliance without heat lamp guard in place Do not splash water on heat lamps Do not wipe heat lamp with wet cloth or sponge The technical content of this manual including any wiring diagrams schematics parts breakdown illustrations and or adjustment procedures is intended for use by qualified technical personnel Any procedure which requires the use of tools must be performed by a qualified technician This manual is considered to be a permanent part of the appliance This manual and all supplied instructions diagrams schematics parts breakdown illustrations notices and labels must remain with the appliance if it is sold or moved to another location WARNING SHOCK HAZARD All serv
13. l surfaces are recommended Metal over combustible material may not meet code for non combustible surfaces Verify that the unit sits firmly ON ALL FOUR LEGS With a spirit level check that the appliance is level front to back and side to side With the adjustable legs adjust as required to level the appliance All four legs must be adjusted to firmly contact the floor in order to prevent tipping Avoid storing flammable or combustible materials in on or near the appliance ASSEMBLY Slide kettle lid over stirrer shaft and lid guide The handle should be toward the door opening Slide the lid up until it is captured by the magnetic holder Slide the stirrer collar over the stirrer shaft Thread the stirrer wand through the slot in the shaft then allow the collar to drop into place Position kettle vertically with the knob down and to the right side Attach kettle to the two hangers Allow kettle to rotate horizontal Connect the kettle electrical pigtail to the twist lock receptacle Thread the heat lamp into the heat lamp socket Install the heat lamp guard Install the drop door and crumb tray saddog Jenueyy SIAUMO 2902 ZEZ 232 306223 Owners Manual WPP Series Popcorn Popper PREPARATION Scoop any remaining popcorn from cabinet and discard Empty crumb tray Be sure inside of kettle is wiped clean and the stirrer wand is properly installed Press the WARMER switch The heat l
14. ly and file CONCEALED DAMAGE claim with them This should be done within fifteen 15 days from the date the delivery was made to you Be sure to retain the container for inspection Wells Manufacturing cannot assume liability for damage or loss incurred in transit We will however at your request supply you with the necessary documents to support your claim saddog SallaS ddM Jenueyy 2902 ZEZ 232 306223 Owners Manual WPP Series Popcorn Popper WARRANTY i SPECIFICATIONS FEATURES amp OPERATING CONTROLS PRECAUTIONS amp GENERAL INFORMATION AGENCY LISTING INFORMATION INSTALLATION OPERATION CLEANING INSTRUCTIONS TROUBLESHOOTING SUGGESTIONS MAINTENANCE INSTRUCTIONS EXPLODED VIEWS WIRING DIAGRAM PARTS amp SERVICE CUSTOMER SERVICE DATA t Thank You for purchasing this Wells Manufacturing Co appliance Proper installation professional operation and consistent maintenance of this appliance will ensure that it gives you the very best performance and a long economical service life This manual contains the information needed to properly install this appliance and to use and care for the appliance in a manner which will ensure its optimum performance MODEL VOLTS 19 WATTS POWER SUPPLY CORD 120 VAC 1500 W 12 5A NEMA 5 15 This manual applies to the following Wells Manufacturing products WPP 6 Popcorn Popper WPP 10 Popcorn P
15. opper KETTLE COVER KETTLE HEATER ELECTRICAL PLUG INSIDE CABINET POPCORN SCOOP MAGNETIC Coen 48 HEAT LAMP BUTTER HOLDER e LAMP GUARD LADLE COVER oe ____ GUIDE KETTLE STIRRER HANGER ROD POPCORN KETTLE LADLE KETTLE KNOB SWITCH FOR CABINET VENT KETTLE HEATER AND STIRRER SWITCH FOR HEAT LAMP AND WARMER sececcsscscss MAGNETIC DOOR CATCH CLEAR ACRYLIC DOOR TEMPERED GLASS BACK AND SIDES DROP DOOR HEATED BOTTOM PLATE DEBRIS GRATE REMOVABLE TRAY COLLECTS UNPOPPED KERNELS Features and Operating Controls WPP 6 and WPP 10 daddog SalliaS ddM Jenueyy 2902 ZEZ 232 306223 Owners Manual WPP Series Popcorn Popper This appliance is intended for use in commercial establishments only This appliance is intended to prepare food for human consumption and to hold that food at temperature for serving No other use is recommended or authorized by the manufacturer or its agents Operators of this appliance must be familiar with the appliance use limitations and associated restrictions Operating instructions must be read and understood by all persons using or installing this appliance Cleanliness of this appliance is essential to good sanitation Read and follow all included cleaning instructions and schedules to ensure the safety of the food product D
16. s authorized service agency or call Wells Manufacturing Co 2 Erik Circle P O Box 280 Verdi NV 89439 phone 775 689 5700 fax 888 492 2783 Service Parts Dept Service Parts Department can supply you with the name and telephone number of the WELLS AUTHORIZED SERVICE AGENCY nearest you CUSTOMER SERVICE DATA please have this information available if calling for service RESTAURANT LOCATION INSTALLATION DATE TECHNICIAN SERVICE COMPANY ADDRESS STATE ZIP TELEPHONE NUMBER EQUIPMENT MODEL EQUIPMENT SERIAL NO VOLTAGE check one 120 Commercial Food Equipment Service Association Wells Manufacturing proudly supports CFESA Commercial Food Equipment Service Association SERVICE TRAINING QUALITY SERVICE CUSTOMER SATISFACTION WELLS MANUFACTURING COMPANY Division of CARRIER COMMERCIAL REFRIGERATION 2 ERIK CIRCLE P O Box 280 Verdi NV 89439 telephone 775 689 5700 fax 888 492 2783 www wellsbloomfield com PRINTED IN CHINA
17. s can be hot to the touch and may cause burns CAUTION BURN HAZARD The kettle and kettle lid will be extremely hot during operation and can cause serious burns on contact To prevent burns always use the kettle knob to rotate or shake the kettle and always use the handle to lift the kettle lid IMPORTANT Follow manufacturer s directions for quantities of oil popcorn salt and flavorings Stirrer Assembly CAUTION ELECTRIC SHOCK HAZARD Disconnect unit from electric power before cleaning CAUTION BURN HAZARD Allow unit to cool completely before cleaning IMPORTANT DO NOT spill splash or pour water into controls kettle receptacle heat lamp socket or wiring IMPORTANT DO NOT use steel wool or abrasive cleansers for cleaning the cabinet PREPARATION Turn ON OFF switch Allow unit to cool completely before cleaning Disconnect unit from electric power before cleaning FREQUENCY Daily or as needed TOOLS Mild Detergent Soft Cloth or Sponge Plastic Scouring Pad CLEANING 1 Disconnect unit from electric power and allow to cool completely before cleaning Shake all debris from kettle Remove drop door Scoop all product from cabinet and discard Empty crumb tray Disconnect kettle plug from twist lock receptacle Tilt kettle fully vertical and lift off of kettle hangers Wipe inside and outside of kettle with a sponge or soft cloth dampened with mild
Download Pdf Manuals
Related Search