Wells HD8799 User's Manual
Contents
1. nS eee WELLS BLOOMFIELD LLC 5 9 5 2 ERIK CIRCLE P O Box 280 Verdi NV 89439 telephone 775 689 5703 fax 775 689 5976 www wellsbloomfield com OWNERS MANUAL for HEATED DISPENSER MODEL HD8799 21 Gallon HD8802 5 Gallon Includes Installation Operation Use amp Care Servicing Instructions Model HD8799 Heated Dispenser IMPORTANT DO NOT DISCARD THIS MANUAL This manual is considered to be part of the appliance and is to be given to the OWNER or MANAGER of the restaurant or to the person responsible for TRAINING OPERATORS of this appliance Additional manuals are available from your WELLS DEALER THIS MANUAL MUST BE READ AND UNDERSTOOD BY ALL PERSONS USING OR INSTALLING THIS APPLIANCE Contact your WELLS DEALER if you have any questions concerning installation operation or maintenance of this equipment PRINTED IN UNITED STATES OF AMERICA p n 75982 Rev D ECN 13380 M595 071101 cps Unless otherwise specified all commercial cooking equipment manufactured by WELLS BLOOMFIELD LLC is warranted against defects in materials and workmanship for a period of one year from the date of original installation or 18 months from the date of shipment from our factory whichever comes first and is for the benefit of the original purchaser only THIS WARRANTY IS THE COMPLETE AND ONLY WARRANTY EXPRESSED OR IMPLIED IN LAW OR IN FACT INCLUDING BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY2. READY THERMOSTAT INDICATOR HEATER ELEMENT ISSUE A 75868 10 Jesuedsig p lp H WAO 8692 u d G6G 595 p n 75982 OpM Heated Dispenser DESCRIPTION PART NO IMPORTANT Use only factory authorized service DRIP TRAY ASSEMBLY pk 6 8855 1 5 and replacement liters For factory authorized service or to order factory authorized replacement parts contact your Wells authorized service agency or call Wells Bloomfield LLC 2 Erik Circle P O Box 280 Verdi NV 89439 Service Parts Dept phone 775 689 5707 fax 775 689 5976 Service Parts Department can supply you with the name and telephone number of the WELLS AUTHORIZED SERVICE AGENCY nearest you CUSTOMER SERVICE DATA please have this information available if calling for service RESTAURANT LOCATION INSTALLATION DATE TECHNICIAN SERVICE COMPANY ADDRESS STATE TELEPHONE NUMBER ee EQUIPMENT MODEL NO EQUIPMENT SERIAL NO VOLTAGE check one 1 120 Commercial Food Equipment Service Association Wells Bloomfield proudly supports CFESA Commercial Food Equipment Service Association SERVICE TRAINING QUALITY SERVICE CUSTOMER SATISFACTION WELLS BLOOMFIELD LLC 2 ERIK CIRCLE P O Box 280 Verdi NV 89439 telephone 775 689 5703 fax 775 689 5976 www wellsbloomfield com PRINTED IN UNITED STATES OF AMERICA
3. included in 85865 FAUCET ASSEMBLY Jesuedsig p lp H VydO 8692 0 G6G 595 p n 75982 OpM Heated Dispenser MODEL HD8802 5 GALLON DISPENSER ITEM PART DESCRIPTION QTY E ITEM PART DESCRIPTION FAUCET ASSEMBLY 1 BODY FAUCET SEAT CUP 8 ASSEMBLY HANDLE 8 PLUNGER 65174 1 8600 27 NUT RETAINING WINGED SHANK FAUCET W O SIGHT GLASS 8600 26 C CLIP FAUCET RETAINING 8600 50 FITTING FAUCET NUT 5 51053 senses EE 8600 7 KNOB TANK COVER 1 included in 85865 FAUCET ASSEMBLY 2 CAUTION Electric Shock Hazard Opening the bottom panel will expose uninsulated electrical components Disconnect dispenser from electrical power before removing bottom panel HANDLE amp PLUNGER ASSY BONNET NUT SEAT CUP bS SHANK ASSY FAUCET BODY Faucet Assembly BASE Drip Tray Assembly POWER CORD MODEL VOLTS WATTS AMPS ACCESS BOTTOM PANEL All internal components are accessible by removing the bottom panel Remove four screws around the bottom of the warmer tank to free bottom panel from tank assembly FAUCET The faucet may be removed from the shank by turning the winged collar clockwise The faucet bonnet may be removed by turning the bonnet nut counterclockwise The seat cup snaps onto the end of the faucet stem DRIP TRAY The grate sets in the drip tray base and may be lifted out D POWER SWITCH
4. 15R receptacle IMPORTANT The ground prong of the plug is part of a system designed to protect you from electrical shock in the event of internal damage Never cut off the ground prong nor twist a blade to fit an existing receptacle Contact a licensed electrician to install the proper circuit and receptacle GROUND PIN U NEMA 5 15P NEMA 5 15R PLUG RECEPTACLE Jesuedsig p lp H VydO 8692 u d S6 595 p n 75982 OpM Heated Dispenser PREPARATION Prior to first use thoroughly clean warmer see page 6 Be sure faucet handle is up and that drip tray is in place under faucet USE Pour product into warming tank Using pre heated product will reduce heat up time Model HD8799 utilizes a fixed thermostat to hold product at 140 F 60 C Model HD8802 thermostat may be adjusted to hold product at 170 F 77 C maximum Reinstall tank cover Plug dispenser into an appropriate electrical receptacle Turn power switch to ON When the READY light glows product is ready to serve Place an appropriate container under the faucet Pull the faucet handle to dispense product Release the handle to stop the flow of product NIGHTLY CLOSE Turn the power switch to OFF and unplug the dispenser If required empty the dispenser and clean TEMPERATURE ADJUSTMENT Model HD8802 only Remove button plug from rear of dispenser to access thermostat Turn shaft of thermostat to adjust setpoint temperature Turn the shaft clockw
5. OR FITNESS FOR ANY PARTICULAR PURPOSE AND OR FOR DIRECT INDIRECT OR CONSEQUENTIAL DAMAGES IN CONNECTION WITH WELLS BLOOMFIELD PRODUCTS This warranty is void if it is determined that upon inspection by an authorized service agency the equipment has been modified misused misapplied improperly installed or damaged in transit or by fire flood or act of God It also does not apply if the serial nameplate has been removed or if service is performed by unauthorized personnel The prices charged by Wells Bloomfield for its products are 1 Resetting of safety thermostats circuit breakers over load protectors and or fuse replacements are not covered by this warranty unless warranted conditions are the cause 2 All problems due to operation at voltages or phase other than specified on equipment nameplates are not covered by this warranty Conversion to correct voltage and or phase must be the customer s responsibility 3 All problems due to electrical connections not made in accordance with electrical code requirements and wiring diagrams supplied with the equipment are not covered by this warranty 4 Replacement of items subject to normal wear to include such items as knobs light bulbs and normal maintenance functions including adjustments of thermostats adjustment of micro switches and replacement of fuses and indicating lights are not covered by warranty 5 Damage to electrical cords and or plug due to exposure to excessiv
6. United States and Canada and void elsewhere Please consult your classified telephone directory your foodservice equipment dealer or contact Service Department Wells Bloomfield LLC P O Box 280 Verdi Nevada 89439 phone 775 689 5707 or fax 775 689 5976 for information and other details concerning warranty cleaning schedules are customer responsibility Those miscellaneous adjustments noted are customer responsibility Proper attention to preventative maintenance and scheduled maintenance procedures will prolong the life of the appliance 7 Travel mileage is limited to sixty 60 miles from an Authorized Service Agency or one of its sub service agencies 8 Alllabor shall be performed during regular working hours Overtime premium will be charged to the buyer 9 All genuine Wells replacement parts are warranted for ninety 90 days from date of purchase on non warranty equipment This parts warranty is limited only to replacement of the defective part s Any use of non genuine Wells parts completely voids any warranty 10 Installation labor and job check outs are not considered warranty and are thus not covered by this warranty 11 Charges incurred by delays waiting time or operating restrictions that hinder the service technician s ability to perform service are not covered by warranty This includes institutional and correctional facilities 3 CONCEALED LOSS OR DAMAGE if damage is unnoticed until the merchand
7. if these instructions are not followed CAUTION Unstable Equipment Hazard It is very important for safety and for proper operation that the warmer is level and stable when standing in its final operating position Provided non skid feet must be installed at each corner of the unit Do not install this appliance if the feet are missing or damaged WARNING ELECTRIC SHOCK HAZARD Warmer must be properly grounded to prevent possible shock hazard Electrical shock will cause death or serious injury ees IMPORTANT Supply power must match nameplate for voltage and phase Connecting to the wrong voltage will damage the warmer or result in decreased performance Such damage is not covered by warranty REFER TO EXPLODED VIEWS PAGE 9 FOR COMPONENT NAMES NUMBERS Unpack the unit Inspect all components for completeness and condition Ensure that all packing materials have been removed from the unit LEVELING THE UNIT Verify that a slip resistant foot is installed at each corner of the dispenser Set the warmer in its operating location Be sure all four feet touch the counter to prevent tipping ELECTRICIAN S INSTALLATION INSTRUCTIONS REFER TO ELECTRICAL SPECIFICATIONS Page 1 Check the nameplate to determine correct electrical service required for the warmer Models HD8799 and HD8802 dispensers are equipped with a cord and plug They requires a 115 125 volt circuit 50 60 Hz 2 wire plus ground with NEMA 5
8. while draining the hot water from the warmer Wipe the warmer inside and out with a soft cloth or sponge dampened with water and mild detergent Rinse the warmer inside and out with a soft cloth or sponge dampened with clean water Wipe the tank cover with a soft cloth or sponge dampened with water and mild detergent Rinse with clean water If necessary clean the faucet and drip tray see page 8 Allow all components to air dry then reassemble Procedure is complete Jesuedsig pejeeH do 286 u d sec 595 p n 75982 OpM Heated Dispenser SYMPTOM POSSIBLE CAUSE SUGGESTED REMEDY Not plugged in or circuit breaker Restore electric power to warmer off or tripped Power switch not ON Turn power switch to ON Internal wiring damage Inspect wiring for burnt wires and proper connections Repair as needed Appliance will not heat Power cord damaged Replace power cord Replace thermostat Light or wiring damaged Thermostat damaged Thermostat damaged Power switch damaged Ready light does not glow dispenser operational MODEL HD8799 2 2 GALLON DISPENSER ITEM PART 4 DESCRIPTION ITEM FAUCET ASSEMBLY BODY FAUCET SEAT CUP ASSEMBLY HANDLE amp PLUNGER 1 8600 27 NUT RETAINING WINGED SHANK FAUCET W O SIGHT GLASS 8600 26 C CLIP FAUCET RETAINING 8600 12 WASHER FLAT NYLON 13 1 8600 50 FITTING FAUCET NUT 5 6 v T 8600 7 KNOB TANK COVER 1 br r o5c nuk o
9. D WIDTH DEPTH TEMPERATURE 20 11 16 12 7 8 14 1 4 2 1 2 gallon 510 mm 328 mm 361 mm 10 liter 60 C HD8802 5 Gallon Dispenser HEIGHT OVERALL OVERALL CAPACITY ADJUSTABLE TO WIDTH DEPTH TEMPERATURE 24 1 4 14 1 4 15 5 gallon 170 F 621mm 361mm 381mm 20 liter 77 C This manual applies to the following Wells products HD8799 212 Gallon Heated Dispenser HD8802 5 Gallon Heated Dispenser TANK COVER KNOB TANK COVER CARRY HANDLES WARMING TANK THERMOSTAT ADJUSTMENT ACCESS 8802 ONLY DISPENSING 4 FAUCET POWER SWITCH 2 7 READY INDICATOR N DRIP TRAY Kr 2 RS 21 SSSR SLIP RESISTANT FEET Fig 1 Features amp Operating Controls Jesuedsig p lp H VydO 8692 u d S6 595 p n 75982 OpM Heated Dispenser WARNING Electric Shock Hazard All servicing requiring access to non insulated components must be performed by qualified service personnel Do not open any access panels which require the use of tools Failure to heed this warning can result in electrical shock WARNING Electric Shock Hazard e Warmer must be properly grounded to prevent possible shock hazard Electrical shock will cause death or serious Injury This appliance is intended for commercial use only CAUTION Equipment Electrical Damage This appliance is intended for use to warm syrup for human consumption No other use is recommended or authorized by the
10. e heat are not covered by this warranty 6 Full use care and maintenance instructions supplied with each machine Noted maintenance and preventative maintenance items such as servicing and NOTE For your protection please note that equipment in this shipment was carefully inspected and packaged by skilled personnel before leaving the factory Upon acceptance of this shipment the transportation company assumes full responsibility for its safe delivery IF SHIPMENT ARRIVES DAMAGED 1 VISIBLE LOSS OR DAMAGE Be certain that any visible loss or damage is noted on the freight bill or express receipt and that the note of loss or damage is signed by the delivery person 2 FILE CLAIM FOR DAMAGE IMMEDIATELY Regardless of the extent of the damage based upon the limitations in this warranty Seller s obligation under this warranty is limited to the repair of defects without charge by a Wells Bloomfield factory authorized service agency or one of its sub service agencies This service will be provided on customer s premises for non portable models Portable models a device with a cord and plug must be taken or shipped to the closest authorized service agency transportation charges prepaid for service In addition to restrictions contained in this warranty specific limitations are shown in the Service Policy and Procedure Guide Wells Bloomfield authorized service agencies are located in principal cities This warranty is valid in the
11. ise is unpacked notify the transportation company or carrier immediately and file CONCEALED DAMAGE claim with them This should be done within fifteen 15 days from the date the delivery was made to you Be sure to retain the container for inspection Wells Bloomfield cannot assume liability for damage or loss incurred in transit We will however at your request supply you with the necessary documents to support your claim Jesuedsig pajeaH do 2862 u d GEG 595 p n 75982 OpM Heated Dispenser Thank You for purchasing this WARRANTY Wells Bloomfield appliance SPECIFICATIONS FEATURES amp OPERATING CONTROLS PRECAUTIONS amp GENERAL INFORMATION AGENCY LISTING INFORMATION INSTALLATION OPERATION CLEANING INSTRUCTIONS TROUBLESHOOTING SUGGESTIONS SERVICING INSTRUCTIONS This manual contains the information needed EXPLODED VIEW amp PARTS LIST to properly install this appliance and to use FAUCET REPAIR and care for the appliance in a manner that WIRING DIAGRAM will ensure its optimum performance PARTS amp SERVICE Proper installation professional operation and consistent maintenance of this appliance will ensure that it gives you the very best performance and a long economical service life p n 48 C co M X xi mk aoo VOLTS WATTS AMPS POWER SUPPLY 50 60 Hz 1 CORD o HD8799 120 200 1 7 6 NEMA 5 15P HD8802 HD8799 277 Gallon Dispenser HEIGHT OVERALL OVERALL CAPACITY FIXE
12. ise to increase temperature Moving the shaft 1 8 turn will change the temperature approximately 10 F CAUTION Burn Hazard Exposed surfaces of the appliance may be HOT to the touch and can cause burns NOTE Product may continue to flow for several seconds after the faucet is released Do not remove the container until all flow has stopped IMPORTANT Your local Health Department can advise whether or not a particular product may be left in the dispenser over night IMPORTANT Temperature adjustment to be performed by authorized personnel only CAUTION Electric Shock Hazard Do not submerge or immerse dispenser in water CAUTION Burn Hazard This procedure requires the use of very hot water Wear protective gloves while cleaning the warmer Very hot water can cause burns IMPORTANT DO NOT use steel wool sharp objects or caustic abrasive or chlorinated cleansers to clean the dispenser PROCEDURE Clean Heated Dispenser PRECAUTIONS Disconnect dispenser from electric power Drain product and allow dispenser to cool FREQUENCY Daily or after draining product from dispenser TOOLS Mild Detergent Clean Soft Cloth or Sponge 1 Long Handle Bristle Brush Disconnect warmer from electric power Drain product and allow warmer to cool before cleaning Fill warmer with very hot water Place an appropriate container under the faucet Use a long handle bristle brush to stir the water
13. manufacturer or its agents DO NOT plug in or energize this appliance until all Installation This appliance is intended for use in commercial establishments nstructions are read and followed where all operators are familiar with the appliance use Damage to the warmer may occur limitations and associated hazards Operating instructions and if these instructions are not warnings must be read and understood by all operators and followed users Except as noted this piece of equipment is made in the USA 7 d and has American sizes on hardvvare All metric conversions are approximate and can vary in size Exposed surfaces of the The following trouble shooting component views and parts lists appliance may be HOT to the are included for general reference and are intended for use by touch and can cause burns qualified service personnel This manual should be considered a permanent part of this appliance The manual must remain with the appliance if it is sold or moved to another location This dispenser is and listed under UL file E9253 This dispenser meets Standard 4 only when installed LISTED operated and maintained in accordance with the enclosed instructions C LISTED NSE STD 4 READ THIS CAREFULLY BEFORE STARTING THE INSTALLATION CAUTION Equipment Electrical Damage DO NOT plug in or energize this appliance until all Installation Instructions are read and followed Damage to the Brewer will occur
Download Pdf Manuals
Related Search