Weider D130 User's Manual
Contents
1. BACKREST To aid in attaching backrest first slide the BACKREST ADJ BAR 11 through one of the hole patterns in the uprights With LONG ANGLE IRON 12 free lower BACKREST 7 to main frame pivot rod Slide the secured LONG ANGLE IRON Hz onto one side of pivot rod Swing the free LONG ANGLE IRON 12 back to its original position and onto the opposite end of the pivot rod See Detail A Replace MACHINE SCREW L that was removed in Step 2 and tighten all machine screws SEAT with SEAT 8 right side up lower SEAT 8 to seat brackets on main frame ign bolt holes and fasten with 2 MACHINE SCREWS L Tighten all MACHINE SCREWS EP u Qo po me STEP 4 LEG CURL M First slide WEIGHT PIN 6 thru o ig angled holes on the front of LEG CURL 5 Align bolt holes and secure with HEX HEAD BOLT M and ACORN NUT N Place COVER CAP 5 over rear extended por tion of WEIGHT PIN 6 Insert ROUND PLASTIC CAP T into end of WEIGHT PIN 6 Insert SQUARE PLASTIC CAP E into end of LEG CURL 5 Position LEG CURL 5 between leg curl brackets on MAIN FRAME 3 Se cure with HEX HEAD BOLT G and LOCK NUT H DO NOT OVER TIGHTEN Re peat the following instructions until all remaining leg curl parts are in place First slide PAD BAR 9 thru proper hole in LEG CURL 5 un til equal amounts of bar are on both sides To help with the following step a small amount of liquid detergent should be applied to bo2. 5 16 20 X 1 3 4 HEX HEAD BOLT 1 BHH 5240 N 5 16 20 ACORN NUT 1 HH 5019 UPRIGHT DECAL _ 1 2BDE 4102 INSTRUCTION MANUAL EXERCISE CHART a J APRE ASSEMBLED WITH SEAT amp BACKREST J WARNING CONSULT YOUR PHYSICIAN CONSULT YOUR PHYSICIAN BEFORE STARTING YOUR EXERCISE PROGRAM IT IS ADVISABLE TO HAVE A PHYSICAL EXAMINATION BY YOUR PHYSICIAN BEFORE YOU ENTER ANY EXERCISE PROGRAM FOR YOUR OWN SAFETY DO NOT BEGIN ANY EXERCISE WITHOUT PROPER INSTRUCTION CHILDREN AND HANDICAPPED PERSONS SHOULD NOT USE ANY EXERCISE EQUIPMENT WITHOUT A QUALIFIED PERSON IN ATTENDANCE TRAIN WITH A PARTNER IT IS RECOMMENDED THAT AN INDIVIDUAL SHOULD NOT WORK OUT WITHOUT A TRAINING PARTNER IN ATTENDANCE SET UP YOUR PROGRAM TO ACCOMMODATE TWO PEOPLE AND YOU WILL BE HIGHLY MOTIVATED 2 IMPORTANT NOTICE BEFORE BEGINNING ASSEMBLY READ THE FOLLOWING PLEASE READ THE INSTRUCTIONS CAREFULLY PAYING PARTICULAR ATTENTION TO ALL WARNINGS CAUTIONS NCTES OR NOTICES LAY OUT UNASSEMBLED PARTS FAMILIARIZE YOURSELF WITH THE DRAWINGS THEN READ AND UNDERSTAND THE INSTRUCTIONS THOROUGHLY THIS PRODUCT MUST BE ASSEMBLED BY AN ADULT PRIOR TO USE DO NOT DESTROY THE PACKING AND CARTON UNTIL THE UNIT IS COMPLETELY ASSEMBLED DO NOT DESTROY THE INSTRUCTION MANUAL USE IT FOR ORDERING REPLACEMENT PARTS N Aa Ww RECOMMENDED TOOLS FOR P
3. ROPER ASSEMBLY ARE AS FOLLOWS A HAMMER PLIERS MEDIUM SIZE FLATHEAD SCREWDRIVER AND TWO 6 ADJUSTABLE WRENCHES STEP 1 FRAME ASSEMBLY Begin by inserting SQUARE PLASTIC CAPS D into UPRIGHT 1 Align bolt holes on L BRACKET 2 with bolt holes on UPRIGHT 1 Secure each L BRACKET 2 with HEX HEAD BOLTS J and Q 3 LOCK NUTS t Align bolt holes on main frame front u bracket and FRONT Y SUPPORT 4 Secure with HEX HEAD BOLTS J and LOCK NUTS K Lower rear u bracket of MAIN E 3 Onto crossmember of UPRIGHT 1 Align bolt holes and secure with HEX HEAD BOLTS J and LOCK NUTS K Insert UARE PLASTIC CAPS E 2 inte ERBNT Tighten all bolts LOOSEN TOR 2 TURNS NOTE The lower or attachment end of the BACKREST 7 can be t identified quickly by the LONG i ANGLE IRONS 12 The LONG ANGLE IRONS 12 will be extended approx imately two inches beyond the STEP 2 BACKREST PREPARATION Backrest pad Turn BACKREST 7 over to expose the work area Both LONG ANGLE IRONS 12 have been fastened to BACKREST 7 for shipment One LONG ANGLE JRON 1 must be loosened in order to assemble ACKREST 7 to main frame pivot rod The lower HEX HEAD BOLT tU must be removed while the upper HEX HEAD BOLT L is only oosened The LONG ANGLE IRON 12 can now swing freely from the lower end of BACKREST 7 A STEP 3 ATTACHING BACKREST amp SEAT
4. SY ur n LES D130 ASSEMBLY INSTRUCTIONS 9 REPLACEMENT PARTS 1081 RECOMMENDED WEIGHT SET 160LBS WEIDER HEALTH AND FITNESS 21100 ERWIN STREET WOODLAND HILLS CA USA 91367 D 130 PARTS LIST 2 01 90 DIAGRAM ORDERING NO PART NAME NO 1 O O UPRIGHT eK 0263 DO1 12 L BRACKET 12 J kx6125 A22 _____3 MAIN FRAME 1 k0151 DOl 41 FRONT SUPPORT A 1 k0116 C14 ___ 5 LEG CURL 1 k0152 DOl 6 WEIGHT PIN 4LA 12 ko0148 C15 1 BACKREST 4 K amp 0393 DO0l ____ 8 SEAT 1 k0394 D01 9 jPADBAR 2 k 6136 cO8 10 FoaAMPAD 4 kK0425 A05 11 BACKREST ADJ BR 1 kK6054 A06 12 LONG ANGLE IRON 2 K 229 pDOo a C HARDWARE BAG _____ 3 4 ROUND PLASTIC CAP 4 X AA 8004 ______ 1 ROUND PLASTIC CAP 1 AA 8005 ____ 1 ROUND PLASTIC COVER CAP 1 Xw 24 8070 D 2 SQUARE PLASTIC CAP 2 X Aa 8000 1 1 2 SQUARE PLASTIC CAP 3 AA 8001 G 3 8 16 X 2 1 2 HEX HEAD BOLT 1 HH 5018 2AA 3 8 16 LOCK NUT 1 mHH s013 3 5 16 20 X 2 1 2 HEX HEAD BOLT 8 X 5015 Po L 1 amp 5 16 20 LOCK NUT 8 J HH 5021 LL 1 4 20 X 3 4 MACHINE SCREW 6 J HH 5022 M
5. th ends of PAD BAR 9 This acts as a lubricant in assembling FOAM PADS HO and also acts as an adhesive after it has dried Slide FOAM PAD onto each end of PAD BAR 9 Insert ROUND PLASTIC CAPS A into each end of PAD BAR 9 4
Download Pdf Manuals
Related Search