Weider E131B User's Manual
Contents
1. height of the Backrest g DECAL Remove backing from DECAL 90 align Decal on Upright and apply it in the position indicated in the illustration STEP 2 BACKREST ASSEMBLY PART NAME 59 1 4 3 4 MACHINE SCREW 4 Position LONG ANGLE IRONS 10 on BACKREST 8 aliging the holes IMPORTANTI THE FLAT SIDE OF THE LONG ANGLE IRONS MUST FACE TO THE OUTSIDE OF THE PAD SEE ILLUSTRATION Secure LONG ANGLE IRONS 10 with 1 4 X 3 4 MACHINE SCREWS 59 3 STEP 3 ATTACHING BACKREST AND SEAT PART NAME 59 1 4 X 3 4 MACHINE SCREW 80 5 16 X 4 HEX HEAD BOLT 55 5 16 NYLON LOCK NUT 81 METAL FERRULE C Assemble 5 16 4 HEX HEAD BOLT 80 through one LONG ANGLE IRON 10 and into METAL FERRULE 81 Continue with Bolt through hole in side of MAIN FRAME 3 into another METAL FERRULE 81 and secure with 5 16 NYLON LOCK NUT 55 C with SEAT 9 right side up lower to Seat Bracket on MAIN FRAME 3 and attach with 1 4 X 3 4 MACHINE SCREWS 59 STEP 4 LEG CURL ASSEMBLY PART NAME 53 5 16 X 2 HEX HEAD BOLT 55 5 16 LOCK NUT 56 3 8 X 2 1 2 HEX HEAD BOLT 57 3 8 LOCK NUT 71 11 2 SQUARE PLASTIC CAP 72 1 ROUND PLASTIC 73 1 ROUND PLASTIC COVER 74 3 4 ROUND PLASTIC Slide WEIGHT 12 through angled hole on front of LEG CURL 11 Align bolt holes and attach with 5 16 2 HEX HEAD BOLT and 5 16 LOCK NUT 55 Assemble2. 1 ROUND PLASTIC COVER CAP 15 73 over rear extended portion of Weight Pin Assemble 1 ROUND PLASTIC 72 into end of Weight Pin Assemble 1 1 2 SQUARE PLASTIC CAPS 71 Into top and end of LEG CURL 11 C Position LEG CURL 11 between Leg Curl Bracket on MAIN FRAME 3 and secure with 3 8 X 2 1 27 HEX HEAD BOLT 56 and 3 8 LOCK NUT 57 DO NOT OVER TIGHTEN THIS BOLTI THE FOLLOWING INSTRUCTIONS ARE REPEATED UNTIL ALL REMAINING LEG CURL PARTS ARE IN PLACE Assembie 3 4 ROUND PLASTIC CAPS 74 into end of PAD BAR 11 1 2 7 Slide PAD BAR 11 1 2 7 through proper hole in LEG CURL 11 until equa amounts of bar are on both sides To help in the following assembly a small amount of liquid dish detergent should be applied to both ends of the Pad Bar D Assemble LARGE FOAM PADS 2 3 4 x 5 13 onto each end of PAD BAR 11 1 2 7 4 STEP 5 BUTTERFLY ASSEMBLY PART NAME 54 5 16 X 5 HEX HEAD BOLT 55 8 16 LOCK NUT 58 1 4 X 2 MACHINE SCREW 0 1 4 LOCK NUT 78 STOPPER PIN 5524 77 PLASTIC SLEEVE 1 2 X 3 2 74 3 4 ROUND PLASTIC CAP 72 1 ROUND PLASTIC CAP 75 PLASTIC BUSHING 76 PLASTIC SLEEVE 71 1 1 2 SQUARE PLASTIC CAP CI there are two Butterfly Attachments with this unit A RIGHT BUTTERFLY 14 and LEFT BUTTERFLY 15 Instructions are given for one and are repeated to assemble the other Assemble BUTTERFLY PAD BAR 17 through the larg
3. ARE BAG BOLTS amp NUTS HARDWARE BAG PLASTICS amp FOAM PAD 5 16 18 X 2 1 4 HEX HEAD BOLT 5 16 18 X 2 1 2 HEX HEAD BOLT 5 16 18 X 2 HEX HEAD BOLT 5 16 18 X 5 HEX HEAD BOLT 5 16 18 LOCK NUT 3 8 16 X 2 1 2 HEX HEAD BOLT 57 3 8 16 LOCK NUT 1 4 20 X 2 MACHINE SCREW 1 4 20 X 3 4 MACHINE SCREW 1 4 20 LOCK NUT 2 SQUARE PLASTIC CAP 71 11 2 SQUARE PLASTIC 72 1 ROUND PLASTIC 1 ROUND PLASTIC COVER 15 3 4 ROUND PLASTIC PLASTIC BUSHING 76 PLASTIC SLEEVE 2 LONG 77 PLASTIC SLEEVE 1 2 DIA X 3 LONG 78 STOPPER PIN 79 5 16 X 1 3 4 HEX HEAD BOLT 80 5 16 X 4 HEX HEAD BOLT 81 METAL FERRULE UPRIGHT DECAL ASSEMBLY MANUAL PCIE QTY 04 12 91 ORDERING NO C0297 E01 C6125 A22 C0116 C14 C6054 A06 C0446 E01 C6136 C08 C1349 E18 C1348 E18 0148 15 0437 25 6156 14 6158 14 C6230 D04 C6157 C14 C6121 A25 C5869 E01 C5870 E01 5054 5022 8002 8001 8005 8070 8004 8112 8091 5301 5343 DE 4103 E131 E134 HARDWARE ILLUSTRATION SHEET 3 8 HEX HEAD BOLT 56 7 n 988 Le 50 51 53 54 79 80 5 16 NYEON LOCK NUT 1 1 2 SQUARE 1 4 NYEON LOCK o PLASTIC CAP 1 4 MACHINE qm 2 SQUARE PLASTIC CAP 3 4 en FPEASTIG CAP 3 8 NYLON LOCK NUT 1 2 X 3 PEAS
4. ASSEMBLY INSTRUCTIONS REPLACEMENT PARTS WEIDER HEALTH AND FITNESS 21100 ERWIN STREET WOODLAND HILLS CA USA 91367 a o BEFORE BEGINNING ASSEMBLY READ THE FOLLOWING THIS PRODUCT REPRESENTS THE STATE OF THE ART IN TECHNOLOGY IN HOME FITNESS EQUIPMENT EVERY EFFORT HAS BEEN MADE TO BRING TO YOU A PRODUCT OF THE HIGHEST QUALITY AND WORKMANSHIP WE HOPE YOU WILL FIND THIS PRODUCT BENEFICIAL TO YOUR PHYSICAL CONDITIONING AND WELL BEING 7 DO NOT LET THE QUANTITY OF PARTS DISCOURAGE YOU BY READING AND FOLLOWING THE ASSEMBLY INSTRUCTIONS YOU WILL FIND IT GOES TOGETHER EASILY THIS UNIT TAKES APPROXIMATELY ONE HOUR OF ASSEMBLY TIME HELPFUL HINTS FOR ASSEMBLY TOOLS REQUIRED FOR ASSEMBLY INCLUDE A HAMMER PLIERS MEDIUM SIZE FLAT HEAD SCREWDRIVER AND TWO 6 ADJUSTABLE WRENCHES PRIOR TO BEGINNING THE ASSEMBLY OF THIS PRODUCT WE RECOMMEND THAT YOU TAKE A FEW MINUTES TO UNPACK AND LAY OUT ALL THE PARTS SO THEY CAN BE EASILY IDENTIFIED INCLUDED WITH THE LITERATURE OF THE UNIT IS AN ILLUSTRATED PARTS LIST TO HELP IN IDENTIFYING AND SIZING PARTS IT IS EXTREMELY HELPFUL IF THE CONTENTS OF THE HARDWARE BAG ARE EMPTIED OUT AND LIKE PARTS GROUPED TOGETHER LE 5 16 X 3 HEX HEAD BOLTS TOGETHER ETC HANDY PLACE TO HOLD THE HARDWARE MIGHT BE TO USE THE INSIDE OF THE CARTON TOP AFTER GROUPING CHECK THE PARTS AGAINST THE PARTS LIST TO IDENTIFY PARTS AND SIZES WRITE THE SIZE AND PART NAME BESIDE EA
5. CH PART SO YOU KNOW EXACTLY WHICH PART TO GO TO FOR A PARTICULAR ITEM THE ASSEMBLY INSTRUCTIONS HAVE BEEN WRITTEN USING CHECK W AS YOU GO ASSEMBLY METHOD BY CHECKING THE BOXES AS YOU GO IT IS VERY EASY TO FOLLOW ALONG THE ASSEMBLY WITHOUT REREADING TO FIND YOUR PLACE IN THE ASSEMBLY YOU WILL ALSO NOTICE THAT AT THE BEGINNING OF EACH ASSEMBLY STEP THERE IS A HARDWARE LIST SHOWING THE QUANTITY AND DESCRIPTION OF THE HARDWARE REQUIRED TO DO ALL ASSEMBLIES IN THAT STEP BY PRE SELECTING THE HARDWARE FOR EACH STEP YOU WILL SAVE TIME AND CONFUSION TAKE NOTE OF ANY SPECIAL WARNINGS CAUTIONS NOTES OR NOTICES LAY OUT UNASSEMBLED PARTS FAMILIARIZE YOURSELF WITH THE DRAWINGS THEN READ AND UNDERSTAND THE INSTRUCTIONS THOROUGHLY THIS PRODUCT MUST BE ASSEMBLED BY AN ADULT PRIOR TO USE DO NOT DESTROY THE PACKING AND CARTON UNTIL THE UNIT IS COMPLETELY ASSEMBLED DO NOT DESTROY THE INSTRUCTION MANUAL USE IT FOR ORDERING REPLACEMENT PARTS HELP SECURE PLASTIC CAPS IN TUBING IT IS ADVISABLE TO GLUE ON ALL PLASTIC CAPS DURING ASSEMBLY USING ANY HOUSEHOLD TYPE GLUE PERIODICALLY CHECK THE UNIT FOR BOLT TIGHTNESS AND PARTS WEAR TO INSURE THAT YOUR EQUIPMENT IS KEPT CONDITION STEP 1 FRAME ASSEMBLY Press 27 SQUARE PLASTIC CAPS 70 into bottom end of UPRIGHT 1 PART NAME D Align bolt holes on L BRACKETS 2 with bolt holes on UPRIGHT 1 Secure 51 5 16 X 2 1 2 HEX HEAD BOLT 4 each L BRACKET 2
6. D IN YOUR WARRANTY CARD CUSTOMER SERVICE 1 800 225 0653 ALL OF THE PARTS FOR THE WEIGHTBENCH CAN BE ORDERED FROM WEIDER HEALTH AND FITNESS PARTS SERVICE DEPT 900 WEST ST JOHN ST OLNEY IL 62450 WHEN ORDERING PARTS WILL BE SENT AND BILLED AT THE CURRENT PRICES PRICES MAY BE SUBJECT TO CHANGE WITHOUT NOTICE STANDARD HARDWARE ITEMS ARE AVAILABLE AT LOCAL HARDWARE STORES TO OBTAIN PARTS DO NOT GO BACK TO THE STORE WHERE YOU PURCHASED THIS UNIT ALWAYS INCLUDE THE FOLLOWING INFORMATION WHEN ORDERING PARTS MODEL NO NAME OF PART ORDERING NUMBER WARNING CONSULT YOUR PHYSICIAN CONSULT YOUR PHYSICIAN BEFORE STARTING YOUR EXERCISE PROGRAM Um IS ADVISABLE TO HAVE A PHYSICAL EXAMINATION BY YOUR PUST BEFORE YOU ENTER ANY EXERCISE PROGRAM FOR YOUR OWN SAFETY DO NOT BEGIN ANY EXERCISE WITHOUT PROPER INSTRUCTION TRAIN WITH A PARTNER IS RECOMMENDED THAT AN INDIVIDUAL SHOULD NOT WORK OUT WITHOUT TRAINING PARTNER IN ATTENDANCE SET UP YOUR PROGRAM TO ACCOMMODATE TWO PEOPLE AND YOU WILL BE HIGHLY MOTIVATED E131B PARTS LIST DAGAA NO UPRIGHT L BRACKET FRONT SUPPORT BACKREST ADJ BAR SMALL FOAM PAD 2 X 6 PAD BAR 3 4 X 11 1 2 BACKREST LONG ANGLE IRON LEG CURL WEIGHT PIN 1 X 13 3 4 LARGE FOAM PAD 2 3 4 X 5 RIGHT BUTTERFLY LEFT BUTTERFLY BUTTERFLY WEIGHT PIN 1 X 11 BUTTERFLY PAD BAR 3 4 PAD BAR 3 4 X 13 1 2 ANGLE BRACKET HARDW
7. TIG SLEEVE 1 ROUND PLASTIC COVER CAP 15 2 PLASTIC SLEEVE 1 3 BOLT LENGTH SCALE
8. e hole in the end of Butterfly Frame aligning bolt holes Secure with 1 4 X 2 MACHINE SCREW 58 and 1 4 LOCK NUT 60 Press 3 4 ROUND PLASTIC CAPS 74 into end of BUTTERFLY PAD BAR 17 Slide LARGE FOAM PAD 2 3 4 X 5 13 onto end of BUTTERFLY PAD BAR 17 Again a small amount of liquid dish detergent will help with this assembly 0 Assemble BUTTERFLY WEIGHT PIN 16 into angled hole on front of Butterfly Frame and attach with 5 16 2 HEX HEAD BOLT 53 and 5 16 LOCK NUT 55 The bolt will go through the Butterfly Frame and Weight Pin PLASTIC SLEEVE 77 will then be assembled onto the folt and secured with the 5 16 NYLON LOCK NUT 55 Press 1 ROUND PLASTIC CAP 72 into end of Weight Pin Slide PLASTIC BUSHING 75 over Weight pin until it against the Butterfly Frame D Assemble PLASTIC SLEEVE 76 over welded Butterfly Tube Slide entire assembly into welded tube bracket on UPRIGHT 1 Insert STOPPER PIN 78 into center of assembly rounded end first making sure the side of the Stopper Pin that has a raised section aligned with the hole in the welded Butterfly tube Push STOPPER PIN 78 into welded Butterfly tube until it clicks into place as the raised section exits the hole Press 1 1 2 SQUARE PLASTIC 71 into end of Butterfly frame REPAIR PARTS AND SERVICE IMPORTANT BEFORE CALLING THE 800 NUMBER IN ORDER TO RECEIVE SERVICE ON THIS PRODUCT YOU WILL HAVE TO FIRST SEN
9. with two 5 16 X 2 1 2 HEX HEAD BOLTS 51 and two 5 16 LOCK NUTS 55 50 5 16 X 2 1 4 HEX HEAD BOLT 2 55 5 16 LOCK NUT 8 C Boit MAIN FRAME 3 front bracket to FRONT SUPPORT 4 using two 5 16 X 70 2 SQUARE PLASTIC CAP 1 3 4 HEX HEAD BOLTS 79 and two 5 16 LOCK NUTS 55 NOTE THE 71 1 1 2 SQUARE PLASTIC CAP EMBOSSED HOLES ON THE FRONT SUPPORT MUST BE FACED TOWARD THE FLOOR 74 3 4 ROUND PLASTIC H 79 5 16 X 1 3 4 HEX HEAD BOLT 58 1 4 X 2 MACHINE SCREW 60 1 4 NYLON LOCK NUT ANGLE BRACKET 19 to MAIN FRAME 3 using 1 4 X 2 MACHINE SCREWS 58 and 1 47 NYLON LOCK NUTS 60 rear u bracket of MAIN FRAME 3 to crossmember of UPRIGHT 1 using two 5 16 X 2 1 4 HEX HEAD BOLTS 50 and two 5 16 LOCK NUTS 55 Press 1 1 2 SQUARE PLASTIC CAPS 71 into ends of FRONT SUPPORT 4 and into top of MAIN FRAME 3 0 Assemble 3 4 ROUND PLASTIC CAPS 74 into each end of PAD BAR 13 1 2 18 and insert bar into large hole in vertical section of MAIN FRAME 3 Bar should be equally spaced on both sides of frame Slide SMALL FOAM PADS 2 1 4 x 6 6 onto each end of PAD BAR 13 1 2 13 A small amount of liquid dish detergent applied to both ends of the Pad Bar will help in this assembly press 3 4 ROUND PLASTIC CAP 74 into handle end of BACKREST ADJ BAR 5 and assembly bar into one of the hole patterns in UPRIGHT 1 The Backrest Adj Bar is used to adjust the
Download Pdf Manuals
Related Search