Weider B242 User's Manual
Contents
1. ASSEMBLY INSTRUCTIONS REPLACEMENT PARTS WEIDER HEALTH AND 21100 ERWIN STREET WOODLAND HILLS CALIFORNIA U S A 91367 207 ED LION B 242 PARTS LIST ET run PETIT FEE EE E UPRIGHTS U A MA CARD E MAIN FRAME ea E BERE MS E A SE EE aoe 6 LEG CURE ADJUSTER 6238 0182 EQUAL ne m 1086 ANGLE IRON 625 68 m SHORT ANGLE cA 5 6119 7 0 SEAT ADJUSTER 0120 EE PAD BAR 12 TFOAM PAD LARGE Be nn DEA A E LEA 3 UPRIGHT ASSEMBLY J 2 6425 0236 14 BACKREST BAR O 2406 6054 15 TFOAM PAD SMALL CB18 0413 e PAD SUPPORT ET 6 26 6123 17 TARM CURL PAD E CA25 0352 1 EEE FEE OE SEERE EEE SANGENE SAS ee ee gee EA J 5 16 20 X 2 1 2 HEX HEAD BOLT 2 5 N20 LOCK P 15 16 20 X 2 HEX HEAD 3 E 620 ACORN HH 5019 378 16 X 2 1 2 HEX HEAD BOLT 1 msme 3 8 16 ACORN NUT oo HH 5020 o HO O 4 20 X 4 HH 5022 AA PIN gt ry WW 7002 rE IN 7777 Fe ZU 50 PLASTIC cap mum 1 4 SO PLASTIC CAP TT aaoo M N 13 47 RD PLASTIC CAP 2 JOA o 17 RD PLASTIC CAP O O o n AA PA 1 4 20 LOCK 5 11 4 20 314 HEAD BOLT 8 HH 5023 INSTRUCTION MANUAL 6 T UPRIGHT DECAL ae AD 059 PR NEO en WHEN ORDERING PARTS IT IS IMPORTANT TO SPECIFY THE MODEL FOR WHICH THE PART IS NEEDED GI2. 10 Assemble PAD SUPPORT 16 to ARM CURL 17 using HEX HEAD SCREWS X which are assembled into curl pad To use arm curl remove leg curl attachment and insert PAD SUPPORT 16 into LEG 3 The pad can be adjusted to desired height and height maintained by inserting EYELET PIN P thru appropriate hole and allowing it to rest on top of leg if i 419 A P WARNING CONSULT YOUR PHYSICIAN CONSULT YOUR PHYSICIAN BEFORE STARTING YOUR EXERCISE PROGRAM IT 1S ADVISABLE TO HAVE A PHYSICAL EXAMINATION BY YOUR PHYSICIAN BEFORE YOU ENTER ANY EXERCISE PROGRAM FOR YOUR OWN SAFETY DO NOT BEGIN ANY EXERCISE WITHOUT PROPER INSTRUCTION CHILDREN AND HANDICAPPED PERSONS SHOULD NOT USE ANY EXERCISE EQUIPMENT WITHOUT A QUALIFIED PERSON IN ATTENDANCE TRAIN WITH A PARTNER 1 RECOMMENDED THAT AN INDIVIDUAL SHOULD NOT WORKOUT WITHOUT A TRAINING PARTNER IN ATTENDANCE SET UP YOUR PROGRAM TO ACCOMMODATE TWO PEOPLE AND YOU WILL BE HIGHLY MOTIVATED
3. T 9 use the EYELET PIN R to hold Seat in highest position Now slide the Seat Support on the Main Frame Rod and the Seat Adjuster Rod and secure with the two BOLTS S you removed in Step 3 STEP 6 Slide ADJUSTABLE LEG ASSEMBLY 6 into the Main Frame tube and adjust to proper height using ADJUSTABLE PIN 1 Take BAR 11 and slide through hole on Adjustable Leg Assembly until equal amounts of the bar are on both sides of tube Place a PLASTIC PLUG N into both ends of Pad Bar Place PLASTIC CAP M into top of Adjustable Leg Assembly STEP 7 Place CURL FRAME 7 in position between the bracket on the adjustable leg assembly Attach D with HEX HEAD BOLT F and LOCKING NUT G DO NOT OVER TIGHTEN The Curl Frame should operate freely Peel the paper off of the RUBBER STOP T Place the Stop on the Main Frame where the Curi Frame strikes the Main Frame va N STEP 8 Take PAD BARS 11 and place through holes on Curl Frame till equal amounts of bar are on both sides of Frame Place ANKLE PADS 12 on each side of bar Next place PLASTIC PLUG N in the ends of the tube Repeat till all pads are in place Place SQUARE PLASTIC CAP K into Curl Frame end Place ROUND PLASTIC CAP O into end of weight tube STEP 9 Slide ADJUSTABLE UPRIGHTS 13 into UPRIGHT TUBES 2 as shown in diagram Adjust to proper position using ADJUSTABLE PIN I STEP
4. VING THE PART NAME AND ORDERING NUMBER OF THE PART STEP 1 Layout BASE 1 attach to UPRIGHTS 2 with BOLTS A and NUTS B finger tighten Place 2 PLASTIC CAPS L into Uprights STEP 2 Place FRAME 3 in position Attacn to Uprights with BOLTS C and NUTS B finger tighten Secure front of Frame to Base with BOLT D and NUT E At this time make sure all bolts are securely tightened Place 3 PLASTIC CAPS K into Base STEP 3 Lay BACKREST 4 and SEAT 5 upside down as shown Remove one ANGLE IRON 9 from the SEAT 5 Then assemble Seat and Backrest as shown by sliding Seat with attached Angle Iron on the SEAT ADJUSTER 10 STEP 4 Slide into position the LOCKING ADJUSTABLE BACKREST BAR 14 in the direction shown in the diagram Turn SEAT 5 and BACKREST 4 right side up and bring down to Main Frame and place Backrest onto Locking Adjustable Backrest Bar Slide the front of the Seat onto the rod on the front of the Main Frame as shown in the diagram Slide the SEAT ADJUSTER 10 into the slot provided in the Main Frame Use the EYELET R to determine the proper adjustment for individual workout The EYELET PIN R will lie across the Main Frame after inserted in the Seat Adjuster After Seat Adjuster has passed through slot in Main Frame place MACHINE SCREW H through bottom hole in Seat Adjuster and secure o D STEP 5 To aid in attaching the SEAT SUPPOR
Download Pdf Manuals
Related Search