Weider E137 User's Manual
Contents
1. TRAIN WITH A PARTNER oar 15 RECOMMENDED THAT AN INDIVIDUAL SHOULD NOT WORK OUT WITHOUT A TRAINING PARTNER IN ATTENDANCE SET UP YOUR PROGRAM TO ACCOMMODATE TWO PEOPLE AND YOU WILL BE HIGHLY MOTIVATED can2. Continue with Bolt through hole in side of MAIN FRAME 3 into another LONG ANGLE IRON 9 and 5 16 FLAT WASHER 39 and secure with 5 16 NYLON LOCK NUT 22 m Don t forget to tighten the four screws 26 Cl with SEAT 8 right side up lower to Seat Bracket on MAIN FRAME 3 and attach with 1 4 X 3 4 MACHINE SCREWS 23 STEP4 LEG CURL HEAD BOLT 0 First assemble WEIGHT PIN 6 through angled hole on front of LEG CURL 5 Align bolt holes and secure with 5 16 X 2 HEX HEAD BOLT 42 and 5 16 NYLON LOCK NUT 22 Place 1 ROUND COVER CAP 15 32 over rear extended portion of WEIGHT PIN 6 and assemble 1 ROUND PLASTIC INSERT CAP 31 into ot end 0 Assemble 1 1 2 SQUARE PLASTIC CAP 34 into top and end of LEG CURL 5 Position Leg Curl assembly between mounting brackets on MAIN FRAME 3 and secure with 3 8 X 2 1 2 HEX HEAD BOLT 24 and 3 8 NYLON LOCK NUT 25 DO NOT OVER TIGHTEN THIS BOLT The Leg Curl must be able to swing freely L Repeat the following instructions until all remaining Leg Curl parts are assembled C Assembte 3 4 ROUND PLASTIC CAPS 30 into each end of PAD BARS 10 g insert PAD BAR 10 through proper hole in LEG CURL 5 until equal amounts of bar are on both sides aid in assembling Foam Pads to Pad Bars a small amount of liquid dish detergent should be applied to both ends of the Pad Bars This acts as a lubricant and also as an adhesive after it has drie
3. ORDERING REPLACEMENT PARTS TO HELP SECURE PLASTIC CAPS IN TUBING IT IS ADVISABLE TO GLUE ON ALL PLASTIC CAPS DURING ASSEMBLY USING ANY HOUSEHOLD TYPE GLUE PERIODICALLY CHECK THE UNIT FOR BOLT TIGHTNESS AND PARTS WEAR TO INSURE THAT YOUR EQUIPMENT IS KEPT IN TOP CONDITION HARDWARE ILLUSTRATION SHEET al 3 8 HEX HEAD BOLT 3 8 NYLON LOCK NUT 16 HEX HEAD BOLT 5 ease vi 5 16 MITON LOCK NUT 40 42 1172 SQUARE 1 4 NYLON LOCK NUT PLASTIC CAP 27 34 zem Au SCREW 2 SQUARE n c e PLASTIC CAP 1 1 2 X 3 bx SLEEVE 3 i 1 ROUND PLASTIC 159 SIORFER PIN 2 PLASTIC SLEE 1 2 3 4 BOLT LENGTH SCALE STEP 1 FRAME ASSEMBLY oc LlAssembie 2 SQUARE PLASTIC CAPS 33 into top and bottom of UPRIGHTS 1 C secure L BRACKETS 2 to UPRIGHTS 1 using 5 16 X 2 1 2 HEX HEAD BOLTS 20 and 5 16 NYLON LOCK NUTS 22 0 boit holes in MAIN FRAME 3 front Bracket and FRONT SUPPORT 4 Secure with 5 16 x 1 3 4 HEX HEAD BOLTS 28 and 5 16 NYLON LOCK NUTS 22 NOTE THE EMBOSSED HOLES ON THE FRONT SUPPORT MUST BE FACED TOWARD THE FLOOR L1 Bolt ANGLE BRACKET 51 to MAIN FRAME 3 using 1 4 X 2 MACHINE SCREWS 26 and 1 4 NYLON LOCK NUTS 27 assemble MAIN FRAME 3 onto cross member of UPRIGHTS 1 using 5 16 x 2 1 4 HEX HEAD BOLTS 21 and 5 16 NYLON LOCK NUTS 22 Bolt BAR HO
4. ASSEMBLY INSTRUCTIONS REPLACEMENT PARTS WEIDER HEALTH AND FITNESS 21100 ERWIN STREET WOODLAND HILLS USA 91367 D137 FLEX PARTS LIST 04 17 91 DIAGRAM NO PART NAME ORDERING NO 1 UPRIGHT 1200 06 2 L BRACKET 6128 05 3 MAIN FRAME 2148 06 4 FRONT SUPPORT C2149 E06 5 LEG CURL C2150 E06 6 LEG CURL WEIGHT PIN 1 X 13 3 4 C0147 C19 7 BACKREST RED VINYL C1308 D11 8 SEAT RED VINYL C1309 D11 9 LONG ANGLE IRON C6233 D11 PAD BAR 3 4 X 11 1 2 C6112 A23 FOAM PAD 2 3 4 X 5 0437 25 BACKREST ADJ BAR C6054 A06 RIGHT BUTTERFLY C6213 C19 LEFT BUTTERFLY BUTTERFLY PAD BAR BUTTERFLY WEIGHT PIN 1 X 11 BAR HOLDER BRACKET C6214 C19 C6215 C19 C6228 C19 0268 011 30 BAR aie 112 207 019 ANGLE BRACKET 06 5 FOMPADZXS C0446 E01 5 16 X 2 1 2 HEX HEAD BOLT 5 16 X 2 1 4 HEX HEAD BOLT HH 5053 5 16 NYLON LOCK NUT HH 5012 1 4 X 3 4 MACHINE SCREW HH 5022 3 8 X 2 1 2 HEX HEAD BOLT HH 5018 3 8 LOCK NUT 1 4 X 2 MACHINE SCREW 1 4 LOCK NUT 5 16 X 1 3 4 HEX HEAD BOLT 3 4 ROUND PLASTIC CAP 1 ROUND PLASTIC CAP 1 ROUND PLASTIC COVER CAP 15 2 SQUARE PLASTIC CAP 1 1 2 SQUARE PLASTIC CAP HH 5013 H
5. H 5255 HH 5011 HH 5301 AA 8004 AA 8005 AA 8070 AA 8002 AA 8001 1 4 7 PLASTIC BUSHING 2 AA 8112 PLASTIC SLEEVE 2 2 AA 8091 STOPPER PIN 2 WW 7038 5 16 FLAT WASHER 2 HH 5127 5 16 X 5 HEX HEAD BOLT 2 HH 5328 PLASTIC SLEEVE 1 2 DIA X 3 2 AA 8128 5 16 X 2 HEX HEAD BOLT 1 HH 5054 HARDWARE BAG BOLTS amp NUTS 1 5879 06 Po HARDWARE BAG PLASTIC amp FOAM 1 C5880 E06 UPRIGHT DECAL FLEX 2 DE 4162 o INSTRUCTION MANUAL BEFORE BEGINNING ASSEMBLY READ THE FOLLOWING THIS PRODUCT REPRESENTS THE STATE OF THE ART IN TECHNOLOGY IN HOME FITNESS EQUIPMENT EVERY EFFORT HAS BEEN MADE TO BRING TO YOU A PRODUCT OF THE HIGHEST QUALITY AND WORKMANSHIP WE HOPE YOU WILL FIND THIS PRODUCT BENEFICIAL TO YOUR PHYSICAL CONDITIONING AND WELL BEING 7 DO LET THE QUANTITY OF PARTS DISCOURAGE YOU BY READING AND FOLLOWING THE ASSEMBLY INSTRUCTIONS YOU WILL FIND IT GOES TOGETHER EASILY THIS UNIT TAKES APPROXIMATELY ONE HOUR OF ASSEMBLY TIME HELPFUL HINTS FOR ASSEMB 1 TOOLS REQUIRED FOR ASSEMBLY INCLUDE A HAMMER PLIERS MEDIUM SIZE FLAT HEAD SCREWDRIVER AND TWO 6 ADJUSTABLE WRENCHES 2 PRIOR TO BEGINNING THE ASSEMBLY OF THIS PRODUCT WE RECOMMEND THAT YOU TAKE A FEW MINUTES TO UNPACK AND LAY OUT ALL THE PARTS S
6. LDER BRACKETS 18 to UPRIGHTS 1 using 5 16 X 2 1 2 HEX HEAD BOLTS 20 and 5 16 NYLON LOCK NUTS 22 Press 1 1 2 SQUARE PLASTIC CAPS 34 into ends of FRONT SUPPORT 4 and top of MAIN FRAME 3 C Assemble 3 4 ROUND PLASTIC CAPS 30 into each end of PAD BAR 13 1 2 50 and insert Bar into large hole in vertical section of MAIN FRAME 3 Bar should be equally spaced on both sides of frame Slide SMALL FOAM PADS 2 X 6 52 onto each end of PAD BAR 13 1 2 50 A small amount of liquid dish detergent applied to both ends of the Pad Bar will help in this assembly gt C Press 3 4 ROUND PLASTIC 30 into handle end of BACKREST ADJ BAR 12 and assemble Bar into one of the hole patterns on UPRIGHT 1 This Bar is used to adjust the height of the Backrest D DECALS Remove the backing from the Decal align the decal on the Upright and apply it to the area indicated by the diagonal striped area in the illustration a STEP 2 BACKREST ASSEMBLY Position LONG ANGLE IRONS 9 BACKREST 7 aligning the holes IMPORTANT THE FLAT SIDE OF THE LONG ANGLE IRONS MUST FACE TO THE INSIDE OF THE PAD SEE ILLUSTRATION L Secure LONG ANGLE IRONS 9 with 1 4 X 3 4 MACHINE SCREWS 23 IMPORTANT Do not tight the MACHINE SCREWS 23 STEP 3 ATTACHING BACKREST amp SEAT PART NAME C BACKREST Assemble 5 16 X 2 1 4 HEX HEAD BOLT 21 through one LONG ANGLE IRON 9 and into 5 16 FLAT WASHER 39
7. O THEY CAN BE EASILY IDENTIFIED INCLUDED WITH THE LITERATURE OF THE UNIT IS AN ILLUSTRATED PARTS LIST TO HELP IN IDENTIFYING AND SIZING PARTS IT IS EXTREMELY HELPFUL IF THE CONTENTS OF THE HARDWARE BAG ARE EMPTIED OUT AND LIKE PARTS GROUPED TOGETHER I E 5 16 X 3 HEX HEAD BOLTS TOGETHER ETC A HANDY PLACE TO HOLD THE HARDWARE MIGHT BE TO USE THE INSIDE OF THE CARTON TOP AFTER GROUPING CHECK THE PARTS AGAINST THE PARTS LIST TO IDENTIFY PARTS AND SIZES WRITE THE SIZE AND PART NAME BESIDE EACH PART SO YOU KNOW EXACTLY WHICH PART TO GO TO FOR A PARTICULAR ITEM 3 THE ASSEMBLY INSTRUCTIONS HAVE BEEN WRITTEN USING CHECK AS YOU GO ASSEMBLY METHOD BY CHECKING THE BOXES AS YOU GO IT IS VERY EASY TO FOLLOW ALONG THE ASSEMBLY WITHOUT REREADING TO FIND YOUR PLACE IN THE ASSEMBLY YOU WILL ALSO NOTICE THAT AT THE BEGINNING OF EACH ASSEMBLY STEP THERE 15 A HARDWARE LIST SHOWING THE QUANTITY AND DESCRIPTION OF THE HARDWARE REQUIRED TO DO ALL ASSEMBLIES IN THAT STEP BY PRE SELECTING THE HARDWARE FOR EACH STEP YOU WILL SAVE TIME AND CONFUSION TAKE NOTE OF ANY SPECIAL WARNINGS CAUTIONS NOTES OR NOTICES LAY OUT UNASSEMBLED PARTS FAMILIARIZE YOURSELF WITH THE DRAWINGS THEN READ AND UNDERSTAND THE INSTRUCTIONS THOROUGHLY THIS PRODUCT MUST BE ASSEMBLED BY AN ADULT PRIOR TO USE DO NOT DESTROY THE PACKING AND CARTON UNTIL THE UNIT IS COMPLETELY ASSEMBLED DO NOT DESTROY THE INSTRUCTION MANUAL USE IT FOR
8. d 7 Assemble LARGE FOAM PADS 2 3 4 X 5 11 onto each end of PAD BARS 10 n MACHINE SCREW 2 UM NYLON LOCK NUT 2 40 5 16 5 HEX HEAD 2 32 5 16 NYLON LOCK NUT 2 3 4 ROUND PLASTIC CAP 2 2 2 2 2 41 PLASTIC SLEEVE 1 2 X 3 21 ROUND PLASTIC CAP Ie BUSHING there are two Butterfly Attachments with this unit A RIGHT BUTTERFLY 13 and a LEFT BUTTERFLY 14 Instructions are given for one and are repeated to assemble the other 0 Assemble BUTTERFLY PAD BAR 15 through the large hole in the end of Butterfly Frame aligning bolt holes Secure with 1 4 X 2 MACHINE SCREW 26 and 1 4 LOCK NUT 27 Press 3 4 ROUND PLASTIC CAPS 30 into end of BUTTERFLY PAD BAR 15 Slide LARGE FOAM PAD 2 3 4 X 5 11 onto end of BUTTERFLY PAD BAR 15 Again a small amount of liquid dish detergent will help with this assembly C Assemble BUTTERFLY WEIGHT PIN 16 into angled hole on front of Butterfly Frame and attach with 5 16 X 5 HEX HEAD BOLT 40 and 5 16 LOCK NUT 22 The will go through the Butterfly Frame and Weight Pin PLASTIC SLEEVE 41 will then be assembled onto the bolt and secured the the 5 16 NYLON LOCK NUT 22 Press 1 ROUND PLASTIC CAP 31 into end of Weight Pin Slide PLASTIC BUSHING 35 over Weight pin until it against the Butterfly Frame D Assemble PLASTIC SLEEVE 36 over welded Butterfly Tube side en
9. tire assembly into welded tube bracket UPRIGHT 1 Insert STOPPER PIN 37 into center of assembly rounded end first making sure the side of the Stopper Pin that has a raised section is aligned with the hole in the welded Butterfly tube Push STOPPER PIN 37 into welded Butterfly tube until it clicks into place as the raised section exits the hole Press a 1 1 2 SQUARE PLASTIC 34 into end of Butterfly frame REPAIR PARTS AND SERVICE IMPORTANT BEFORE CALLING THE 800 NUMBER IN ORDER TO RECEIVE SERVICE ON THIS PRODUCT YOU WILL HAVE TO FIRST SEND IN YOUR WARRANTY CARD CUSTOMER SERVICE 1 800 225 0653 ALL OF THE PARTS FOR THE WEIGHTBENCH CAN BE ORDERED FROM WEIDER HEALTH AND FITNESS PARTS SERVICE DEPT 900 WEST ST JOHN ST OLNEY iL 62450 WHEN ORDERING PARTS WILL BE SENT AND BILLED AT THE CURRENT PRICES PRICES MAY BE SUBJECT TO CHANGE WITHOUT NOTICE STANDARD HARDWARE ITEMS ARE AVAILABLE AT LOCAL HARDWARE STORES TO OBTAIN PARTS DO NOT GO BACK TO THE STORE WHERE YOU PURCHASED THIS UNIT ALWAYS INCLUDE THE FOLLOWING INFORMATION WHEN ORDERING PARTS MODEL NO NAME OF PART ORDERING NUMBER WARNING CONSULT YOUR PHYSICIAN CONSULT YOUR PHYSICIAN BEFORE STARTING YOUR EXERCISE PROGRAM IT IS lt ADVISABLE TO HAVE A PHYSICAL EXAMINATION BY YOUR PHYSICIAN BEFORE YOU ENTER ANY EXERCISE PROGRAM FOR YOUR OWN SAFETY DO NOT BEGIN ANY EXERCISE WITHOUT PROPER INSTRUCTION
Download Pdf Manuals
Related Search