Weider WG8925 User's Manual
Contents
1. WEIGHT BUSHING 7 PIN GROOVE 146 MADE IN crx 145 CANADA WEIGHT BUSHING PIN GROOVE 146 107 ES a at ee me et Am eee ee ae 3 Assemble two RUBBER BUMPERS 9 to the smaller hole locations on the top of the Welded Bracket at the bottom PO u dP of the REAR UPRIGHT 17 using two ATE C 48 32 SCREWS 10 to bolt down _ T through the Bumpers and then through the Bracket of the Upright Assemble a 8 WASHER 144 onto each Bolt and then secure with 8 32 NUTS 143 Assemble the REAR UPRIGHT 17 onto the two inner 5 16 X 2 1 2 CARRIAGE BOLTS 1 previously assembled into MA the end of the BASE 15 with NO Flat Bracket Make sure the Rear Upright is 143 positioned with the Open Slot facing away from the center of the unit Se cure the Upright with two 5 16 NYLON LOCK NUTS 4 The Weight Stack will have thirteen 10 LB WEIGHTS 107 and one 20 LB WEIGHT 145 Into the top of each of the 10 and 20 LB Weights press a WEIGHT BUSHING 146 Note again that Weider is cast in the top of the 10 LB Weights and Made in Canada in the 20 LB Weight Working with one Weight at a time slide thirteen 10 LB WEIGHTS 107 onto the REAR UPRIGHT 17 making sure that the Weider logo is on top and This Collar must be installed facing the weight selector tube nj that the Pin Groove in the top of th2. 23 and then bolt through the back of the VAF Upright and the Pivot Tube Assemble another 5 16 FLAT WASHER 45 onto the Bolt and secure with a 5 16 NYLON LOCK NUT 4 6 Press two 1 3 4 INNER CAPS 29 into the ends of the arms of the ARM PRESS 12 Insert one 1 3 8 O D x 1 long PLASTIC BUSHING 149 into the outside of each weided bushing at the top of ARM PRESS SELECTORH 3 Assemble the ARM PRESS SELECTOR 3 to the inside and top of the ARM PRESS 12 by inserting the 11 ARM PRESS TUBE 104 through one side of the Arm Press and then through both Plates of the Arm Press Selector and finally through the oposite side of the Arm Press Secure using two 5 16 x 2 BOLTS 95 to bolt through the large hole opening in the top and front of the Arm Press and then through the 11 Arm Press Tube Assemble a 5 16 NYLON LOCK NUTS 4 Press 1 COVER CAPS 100 onto the ends of the 11 ARM PRESS TUBE 104 Press 3 4 PLUG CAPS 119 3 4 stamped inside 36 into the large hole where the 5 16 X 2 Bolts 95 were assembled into the front of the ARM PRESS 12 Assemble the SHORT HANDLES 47 into the lower ARM PRESS 12 arms Attach each Short Handle by first asembling a 5 16 FLAT WASHER 45 and a 1 2 X 3 8 SPACER 57 onto each 5 16 X 2 1 4 BOLT 23 and then bolting through the front of the Arms and then through the Short Handle Assem ble another 5 16 FLAT WASHER 45 onto the Bolt and secure with
3. 5 16 FLAT WASHER 45 onto a 5 16 X 3 1 4 BOLT 115 and insert in the hole behind the E 9 Lever Arm on FRONT UPRIGHT 19 7 NEP Press a 1 3 4 INNER CAP 29 into the top of the VAF UPRIGHT 97 Press 1 ROUND CAPS 43 into the 5 shorter end of the Welded Tubes on the upper VAF Upright Remove the 3 8 NYLON LOCK NUT 63 from the pre assembled 3 8 X 2 3 4 BOLT 55 in the lower Cross member of the FRONT UPRIGHT 19 DO NOT remove the Bolt Assemble the VAF UPRIGHT 97 onto the pre assembled 3 8 X 2 3 4 BOLT 55 in the Cross member of the Front Upright and also onto the pre assembled 5 16 X2 1 2 CARRIAGE BOLTS 1 in fhe STABILIZER 16 Re assemble the 3 8 NYLON LOCK NUT 63 to the 3 8 X 2 3 4 bolt 55 Assemble a 5 16 FLAT WASHER 45 onto a 5 16 X 2 1 2 BOLT 14 and bolt through the remaining hole in the Cross member of the FRONT UPRIGHT 19 and then into the Welded Bracket of the VAF UPRIGHT 97 Fasten with a 5 16 NYLON LOCK NUT 4 DO NOT tighten this assembly at this time Attach the VAF Upright to the STABILIZER 16 with two 5 16 NYLON LOCK NUTS 4 Tighten ALL Nylon Lock nuts used in the previous assernbly steps Steps 4 5 Press 1 ROUND CAPS 43 into the ends of the STEPPER TUBE 148 Insert the STEPPER TUBE 148 into the hole location on the lower VAF UPRIGHT 97 Assemble a 5 16 FLAT WASHER 45 and a 1 2 X 3 8 SPACER 57 onto a 5 16 X2 1 4 BOLT
4. by sufficient proof of purchase All returns must be pre authorized by WEIDER This warranty does not extend fo any product or damage to a product caused by or attributable to freight damage abuse misuse improper or abnormal usage or repairs not provided by a WEIDER authorized service center or for products used for commercial or rental Pree No other warranty beyond that specifically set forth above is authorized by WEIDER WEIDER IS NOT RESPONSIBLE OR LIABLE FOR INDIRECT SPECIAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THE PRODUCT OR OTHER DAMAGES WITH RESPECT TO ANY ECONOMIC LOSS LOSS OF PROPERTY LOSS OF REVENUES OR PROFITS LOSS OF ENJOYMENT OR USE COST OF REMOVAL INSTALLATION OR OTHER CONSEQUEN TIAL DAMAGES OF WHATSOEVER NATURE SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OR INCIDENTAL OR CONSEQUENTIAL DAMAGES ACCORDINGLY THE ABOVE LIMITATION MAY NOT APPLY TO YOU THE WARRANTY EXTENDED HEREUNDER IN IN LIEU OF ANY AND ALL OTHER WARRANTIES AND ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE IS LIMITED IN ITS SCOPE AND DURATION TO THE TERMS SET FORTH HEREIN SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS ACCORDINGLY THE ABOVE LIMITATION MAY NOT APPLY TO YOU This warranty gives you specific legal st You may also have other rights which vary from state to SIC WEIDER INC 1500 S 1000 W LOGAN UT 84321 9813 Pa
5. 5 16 NYLON LOCK NUTS 4 Press a 1 ROUND CAP 43 onto one end of each lt SHORT HANDLE 47 Position four 1 4 FLAT WASHER 6 on top and at the front of the FRONT UPRIGHT 19 at the four bolt hole locations Position a THIN METAL PLATE 99 between the Flat Washers Apply grease to the 11 ARM PRESS TUBE 104 between the top of the ARM PRESS 12 Assemble the two ARM PRESS BUSH INGS 60 around the Tube and set this assembly onto the top and front of the Front Upright and onto the Thin Metal Plate making sure to position the Arm Press with the Joining Bracket on the Selector Plates toward the inside of the unit Place the ARM PRESS CAP 59 on top of the ARM PRESS BUSHINGS 60 Bolt in place using four 1 4 X 5 4 SCREWS 7 to bolt up through the bottom of the Front Upright through the Flat Washers and the Atm Press Cap Secure with 1 4 NYLON LOCK NUTS 5 Attach the BAR HOLDER 58 to the top of the FRONT UPRIGHT 19 and to the front of the ARM PRESS CAP 59 using two 1 4 X 3 A TAPER SCREWS 89 to bolt down through the Bar Holder and then through the Front Upright Secure with 1 4 NYLON LOCK NUTS 9 Assemble the J PIN 61 into the upper ARM PRESS 12 and thorugh one of the hole settings in the ARM PRESS SELECTOR 3 7 Attach the SHORT ARM SHOCKS 25 to the Welded Joining Bracket on the ARM PRESS SE LECTOR 3 using 5 16 X 1 3 4 BOLTS 106 to bolt through the Shocks Next as
6. Cees Ss 1 RR RAS PEN RA paket eee po NERO INA HS N MULTI STATION PROFESSIONAL QUALITY FITNESS SYSTEM Model No WG89250 Serial No jg Ol M Ww nsssas rr hr uU 3 our TE Serial Number Decal Under Seat QUESTIONS As a manufacturer we are com mitted to providing complete customer satisfaction If you have questions or find there are missing or damaged parts we will guarantee you complete satisfaction through direct assistance from our factory TO AVOID UNNECESSARY DELAYS PLEASE CALL DIRECT TO OUR TOLL FREE CUSTOMER HOT LINE The trained technicians on our customer hot line will provide immediate assistance free of charge to you CUSTOMER HOT LINE 1 800 225 0653 Mon Fri 6 a m 6 p m MST CAUTION Read all safety precautions and instructions in this owner s manual before using this equip ment Save this owner s manual for future reference PATENT PENDING TABLE OF CONTENTS IMPORTANT SAFETY PRECAUTIONS 2 BEFORE YOU BEGIN 2 pes ASSEMBLY 4 ADJUSTMENT AND WEIGHT RESISTANCE CHART 19 TROUBLE SHOOTING AND MAINTENANCE 22 2 ORDERING REPLACEMENT PARTS BACK COVER LIMITED WARRANTY BACK COVER IMPORTANT SAFETY PRECAUTIONS WARNING To reduce the risk of serious injury read the following important safety pieces before using the hard drive system 1 Read all instructions in this owner s manual and in the accompanying li
7. EAN RR AR NM TITTI M OOD NN TASSE ANNE S ANS x MEN H OSA TI ADDD RES H X x hk E Nis E J p o A i V O 7 NS S QE NY fv M S SN NG 7 3 TENS NERA NN SA Ne Teh rr AEN NV NN ANN AINSI t n S Oo na ARN SE SRY o B SANSA S N SES SESE NSS SASRA SSPESQKED AN N S SRST AR IAS E MAN NEN Y by A v PONS NN tb SLES NS S SA X SRE ROR SEEN ANY A ee vy HERPES e ec B OH on eee CHEER EUER d n een N e ch y NS M i L ees eeene th rH Hoc x TAN lt BRAS ay o SPSS M SRE gt K A as ELS verversen NEN NM N INISAN SVEN WY BRS RRS SN QN RASS N Cy ask ew ANS ANSA AN RNN N Ner S SN ND N ENSE NEN NS SS NEN SN M S a YA e f ao c 1 K J i L Military Press Seat Ad CRANE ONSE Wn ML P PRORA A gt SH NS A x AS SESS SERRE Honan N SOE RI NE SET ENS eo e NEIN TES ESSEN Y ION SER PR A H ARMS M PORRO ARS Sot Soke ONS H AA SANA OS j Ro uS R ONIN NOY INON SRN SUSY Sees i a e oD te SOOO x s gt Te RS Mi o M ON e a V e e 4 OND A Oy n 5 S D NN d i xe Q eS a Aa H PARA SAS M DAOC ANS ki SONG tao QOO TN N ME oh a RR SRN SY a NN RS SN 2 e N C a cx EMEN ey d QNO T NER ra APO SEIN S SESS RES VA ERE REE R f 1 d EIEEE IETEN V 2 Y A nf SANI SNE 1 1 M E H voco nb A A pa ri e M Cv t RSS SRS d d REND UD E DR DEM Leg Lever SE l My o Bi CO KO NR RAR A
8. LE BRACKET 135 Fasten a 1 4 NYLON LOCK NUI 5 about halfway up the threaded end of the Weight Cable See insert drawing B Assemble a WEIGHT BRACKET 110 and a 1 2 X 7 16 BUSHING 134 onto a 5 16 X 1 1 4 BOLT 2 Insert the CABLE BRACKET 135 and CABLE 70 down into the top of the WEIGHT TUBE 108 inside the REAR UPRIGHT 17 Insert the 5 16 X 1 1 4 into the Weight Tube and on thread into the CABLE BRACKET 135 po sitioning the J Hook on the WEIGHT BRACKET 1 10 into the Pin Groove under the top WEIGHT 145 Insert a WEIGHT SELECTOR PIN 112 into one of the Pin Groove and tighten the assembly Assemble a THIN RUBBER BUMPER 147 to the top and front of the FRONT UPRIGHT 19 with a 8 X 1 2 SELF TAPPING SCREW 133 Attach the lower FRONT UPRIGHT 19 to the BASE 15 with two 5 16 NYLON LOCK NUTS 4 DO NOT tighten this assembly at this fime Attach the FRONT UPRIGHT 19 to the CENTER UP RIGHT 18 using a 5 16 X 2 3 4 BOLT 122 To bolt through the Welded Brackets below the lower Cross member of the Front Upright and through the hole at the top of the Center Upright Fasten with a 5 16 NYLON LOCK NUT 4 DO NOT tighten at this time Assemble the FRONT UPRIGHT 19 to the REAR UPRIGHT 17 by first assembling a 5 16 FLAT WASHER 45 onto a 5 16 X 1 3 4 SCREW 53 and then bolting into the Rear Upright and then into the Cross member of the Front Upright Assemble a
9. PR RRS YA NI SR A n dh PEE 2 Rear Weight stack Front Weight Stack iu Tit 1 EMI es j Low Pulley Station Foot Plates Co ASSEMBLY Assembly requires two people Due to the size and weight of the hard drive system it should be assembled in the location where it willbe used Place all parts in a cleared area and remove the packing materials Do not dispose of the packing materials until assembly is completed Before beginning assembly read each step and look at each drawing carefully As you assemble the hard drive system make sure that all parts are oriented as shown in the drawings For help identifying the small part used in assembly refer to the PART IDENTIFICATION CHART accompanying this owner s manual 4 Assembly requires the following fools not included two adjustable wrenches a philips screwdriver a flat head screwdriver and two rubber mallets Grease and a small bowl of soapy water are also needed 1 Begin by pressing a 2 INNER CAP 13 and a 2 OUTER CAP 127 onto the BASE 15 Press a 2 OUTER CAP 127 onto the STABILIZER 16 Turn the Stabilizer so that the small hole near the Welded bracket is to ihe top Assemble the BASE SHROUD BRACKETS 20 to the bottom of the BASE 15 Position one Bracket on the leg of the Base which has NO Flat Bracket Place the Bracket at the hole location between the Two sets of holes and also position the Bracket so that the longer flat side is tow
10. Y Ma Mx et ook Y Y o tas o es g Tute SRA a 2D Re SR or T oA S aval ORS a ke dee N R S A NS d AS a ea og ae LER LS AADAT TINA Vet AIA oe 2 f I D rero ERE AA Batten mete Ee il fru Ny T SE apne 2 Y Ee v E UC M EEN gs ord ET a A z y Sete re bos TD a 5 ves BASEN Sh Y 57 a ea Dr Er EA AA ie ire IL eee i M ap teat Pan w AUI E s X tg cr ua x 11 Press a 1 1 2 INNER CAP 38 onto the one end of the LEVER ARM 94 Press two 1 3 8 BUSHINGS 90 into the other end of the Lever Arm Assemble the LINK ARM 96 to one side of the Lever Arm by first inserting a 3 8 X 21 2 CARRIAGE BOLT 103 into the square hole of the Link Arm Add a 3 8 FLAT WASHER 64 onto the bolt and then insert through the Lever Arm welded inner bushing Next assemble another 3 8 FLAT WASHER 64 onto the Bolt and se cure with a 3 8 NYLON LOCK NUT 63 slide the LEVER ARM 94 onto the lower Welded Pivot Tube on the VAF UPRIGHT 97 making sure to orient the Lever Arm toward the in side of the unit with the Welded U Bracket on the bottom Also the Link Arm must be positioned on the side of the Lever Arm nearest the CENTER UPRIGHT 18 Using a 1 COVER CAP 51 as an aid drive a 1 RETAINER RING 90 onto the Pivot Tube to secure the Lever Arm in place Note that the teeth in the Retainer Ring are tilted slightly to one side The teeth should be away from the Pivot Tube asit is driven on Tap in place
11. ard the inside of the unit Secure in place using a 48 X 1 2 SELF TAPPING SCREW 133 to bolt up through the bottom of ihe Bracket and into the bottom of the Base Position the second Shroud Bracket on the opposite side of the intersection of the legs of the Base between the intersection and the welded cornor bracket Position the Bracket with the iong flat side on the inside of the unit Secure in place with a 8 X 1 2 SELF TAPPING SCREW 133 bolting up through the bottom of the Bracket and into the bottom of the Base Insert eight 5 16 X 2 1 2 CARRIAGE BOLTS 1 up through the bottom of the BASE 15 insert two 5 16 X 2 1 2 CARRIAGE BOLTS 1 up through the STABILIZER 16 Attach the STABILIZER 16 to the BASE 15 by first assembling 5 16 FLAT WASHERS 45 onto two 5 16 X 2 3 4 BOLTS 122 and then bolting through the Base and into the Welded Bracket of the Stabilizer Secure with 5 16 NYLON LOCK NUTS 4 E Attach a RUBBER BUMPER 9 to the top of the BASE 15 in the hole location near the intersection of the Base Legs Use a 1 1 4 TAP SCREW 8 to boli down through the Rubber Bumper and into the Base Attach a RUBBER BUMPER 9 to the top of the STABILIZER 16 in the hole located near the Welded i Bracket using a 1 1 4 TAP SCREW 8 WELDED wo BO BRACKET ema m e ee te E Assemble the CENTER UPRIGHT 18 onto the two 5 16 X 2 1 2 CAR RIAGE BOLTS 1 previously assem bled in the BASE 15 a
12. e Weights is on the same side of the Rear Upright as the Open Slot Assemble four ROLLERS 109 onto the short Pins on a WEIGHT TUBE 108 making sure that the collar of each Roller is facing the Weight Tube See Detail A Slide the Weight Tube down info the top of the REAR UPRIGHT 17 d i re s i Stl asec PEN IERI a LINEA CM M E MEM C C E M MCI EC QD DUC MN DE ee vaa c 4 Assemble the FRONT UP whee t Pd RIGHT 19 onto the two 5 16 oe DRAWING A es X 2 1 2 CARRIAGE BOLTS 1 previously assembled in the BASE 1 leg with the smaller Welded Flat Bracket DO NOT secure at this time Insert the end of the WEIGHT CABLE 70 down into the top of the REAR UPRIGHT 17 E Assemble the UPRIGHT BRACKETS 84 around and behind the holelocations on the upper REAR UPRIGHT 17 and then assemble the upper FRONT UPRIGHT 19 over the top of the Rear Upright positioning the Brack ets between the two Uprights Align the bolt holes Assemble 5 16 FLAT WASHERS 45 onto two 5 16 X 3 1 4 BOLTS 115 and then bolt through the Front Up right the Upright Brackets and the Rear Upright NOTE Make sure the WEIGHT CABLE 70 is positioned behind the Bolts Assemble another 5 16 FLAT WASHER 45 onto each Bolt followed with a 5 16 NYLON LOCK NUT 4 DO NOT tighten this assembly at the time See insert drawing A Insert the threaded end of ihe WEIGHT CABLE 70 into the top of the CAB
13. eth of the Retainer Ring should be positioned outward and use the 1 COVER CAP 51 as an 25 aid to help secure the Retainer Ring in place Tap the Cap and Retainer Ring on using a mallet Assemble a 3 8 FLAT WASHER 64 onto the threaded bolt in the LARGE LINK TUBE 88 Next assemble this bolt into the Welded U Bracket on the LEVER ARM 94 Fasten with a 3 8 JAM NUT 141 Attach the other end of the LARGE LINK TUBE 88 to the bolt hole location in the center of the MILITARY PRESS ARM 87 using a 3 8 X 3 1 4 BOLT 159 to bolt through the Large Link Tube Next assemble a 3 8 FLAT WASHER 64 onto the Bolt and then continue now to bolt through the Military Press Arm Fasten with a 3 8 NYLON LOCK NUT 63 but DO NOT over tighten This assembly asit must be able to move freely 19 ife Front Upright 87 97 SS A E NEST 2 26 Center Upright 16 oO 12 Press 1 ROUND CAPS 43 into the one end of the LONG HAN DLES 81 Press 1 1 2 INNER CAPS 38 into the ends of the 86 LEFT VAF ARM 24 and the RIGHT VAF ARM 79 Attach the LEFT and RIGHT VAF ARMS 24 amp 79 to the sides of the upper VAF UPRIGHT 97 us ing two 5 16 X 2 1 2 BOLTS 14 and 5 16 NYLON LOCK NUTS 4 Bolt the LONG HANDLES 81 into the LEFT and RIGHT VAF ARMS 24 amp 79 by first assembling a 9 16 FLAT WASHER 45 and a 1 2 x 1 4 BUSHING 44 onto a 9 16 X 2 BOLT 95 and
14. f you feel pain or dizziness at any time while exercising ss immediately and begin cooling down WARNING Before beginning ihe or any exercise program consult your physician This is especially important fro persons over the age of 35 or persons with pre existing health problems Read all instructions before using WEIDER assumes no responsibility for personal injury or property damage sustained by or through the use of this product 2 BEFORE YOU BEGIN xe n Thank you for selecting the versatile WEIDER 8925 Hard Drive System The WEIDER 8925 offers an impressive array of weight stations designed to develop every major muscle group o f the body Whether your goal is to tone you body build dramatic muscle size and strength or improve your cardiovascular System the WEIDER 8925 will help you to achieve the specific results you want For you safety and benefit read this manual carefully before using the WEIDER 8925 Hard Drive System If you have additional questions please call our Customer Service Department toll free at 1 800 225 0653 note the product model number and serial number before calling The model number is WG89250 The serial number can be found on a decal attached to the 8925 see the front cover of this owner s manual ASSEMBLED DIMENSIONS Height 74 inches Base 90 inches x 75 Butterfly Arms Press Arm Military Press Squat Arm Vertical Knee k Raise VKR Arm IEEE ROSA CR S
15. gh the top of the Seat Frame Assemble 1 4 FLAT WASHERS 6 onto the Bolts and secure with 1 4 NYLON LOCK NUTS 5 Attach the SEAT 31 to the SEAT BRACKETS 39 making sure fo align the narrow end of the Seat toward the Bracket on the Seat Frame Secure using 1 4 X 3 4 SCREWS 7 to bolt up through the Brackets and into the Seat Press a 1 1 2 INNER CAP 38 into the bottom end of the LEG LEVER 33 Attach the LEG LEVER 33 to the SEAT FRAME 32 with a 5 16 X2 1 4 BOLT 23 and a 5 16 NYLON LOCK NUT 4 DO NOT over tighten as the Leg Lever must pivot freely Insert the 5 16 X 2 1 2 EYEBOLT 37 through the back of the LEG LEVER 33 Slide a 5 16 FLAT WASHER 45 onto the Eyebolt and tighten a 5 16 NYLON LOCK NUT 4 onto the Eye bolt Press 3 4 ROUND CAPS 36 into the ends of two PAD TUBES 35 Insert one PAD TUBE 35 into the ac cess hole at the front of the SEAT FRAME 32 Center the Pad Tube and slide a 7 FOAM PAD 34 onto each end of it insert the other Pad Tube into the lower LEG LEVER 33 and slide a 7 Foam Pad onto each end of if EE E Position the Bracket on the SEA FRAME 32 onto the Welded Pin on the lower FRONT UPRIGHT 19 Align the hole in the Bracket with the hole in the Upright and secure using a 5 16 X 2 3 4 CARRIAGE BOLT 118 to bolt through the Seat Frame and the Upright Tighten a 5 16 KNO 11 onto the Bolt Attach the Leg Lever to the Lower Pulley
16. gs so that the teeth are pointed down The 1 Plastic Cap can be used to help drive the Retainer Rings onto the Pivot Tubes Align the Retainer Rings and Cap with the Pivot Tube and lightly drive the assembly in place with the aid of a mallet Slide the 8 FOAM PADS 28 onto the LEFT ARM 27 and the RIGHT ARM 105 and position them about half way up each Arm Assemble the ARM BRACKETS 124 to the 1 X 2 Welded Tubes on the LEFT and RIGHT ARMS 27 amp 105 making sure to orient the Bracket with the longer portion of the round tube of the Bracket to the top Secure in place using a 3 8 X 3 1 4 BOLT 139 to bolt up through the Bracket and into the bottom of the Welded Tubes Secure with 3 8 NYLON LOCK NUTS 63 Assemble the wider end of the LONG ARM SHOCKS 131 in the ARM BRACKETS 124 on the LEFT ARM 27 and the RIGHT ARM 105 Bolt in place using 5 16 X1 3 4 BOLTS 101 and 5 16 NYLON LOCK NUTS 4 Insert the UPPER SHOCK BAR 26 into the UPPER Welded Tube on the PIVOT ARM 75 on the FRONT UPRIGHT 19 Center the Bar making sure the slotted side faces the Long Arm Shock Assemble the Long Arm Shocks onto the Bar and secure using 1 4 X 1 1 4 BOLTS 66 and 1 4 NYLON LOCK NUTS 5 Press 3 4 COVER CAP 65 onto each end of the SHOCK BAR 26 13 Attach a SEAT BRACKET 39 to the rear hole of the Welded Tube on the lower ARM UPRIGHT 138 us ing a 1 4 X21 2 CARRIAGE BOLT 150 to b
17. hments are in the correct starting position for the exercise to be performed If there is any slack in the cable or chain as an exercise is performed the effectiveness of the exercise will be reduced CHANGING THE WEIGHT SETTING The Hard Drive System features dual weight stacks to allow people to exercise at the same time The rear weight stack is connected to the high pulley Station the low pulley station and the arms the front weight stack is connected to the military press squat arm To change the weight setting of either weight stack insert an L Pin 112 under fhe desired Weight 107 Make sure to insert the L Pin until the bent end of the L Pin is touching the Weights and turn the bent end downward The weight setting of either weight stack can be changed in increments of 10 pounds Nofe Due to the cables and pulleys the actual amount of resistance at each station may vary slightly from the weight setting of the weight stack Refer to the chart above to determine the actual resistance you will get at each station T ADJUSTING THE BACKREST The Large Backrest 30 can be adjusted to any of the three positions To change the position first remove the 5 16 Knob 11 and 5 16 x 2 3 4 Carriage Bolt 113 Pivot the lower end of the Large Backrest until one of the three holes in the Adjustment Bracket 22 is aligned with the hole in the Front Upright 19 Insert the Carriage Bolt through the Adjustment B
18. ifted off the page stack LE O EE ZE SE IE EE EEA SEE EE d If the cables cannot be tightened enough as de scribed above the cables may need to be re placed See the back cover of the owner s manual for information about ordering replacement parts 21 ORDERING REPLACEMENT PARTS To order replacement parts simply call our Customer Service Department toll free at 1 800 225 0653 Monday through Friday 6 a m until 6 p m Mountain Time excluding holidays To help us assii you please be prepared to give the following information 1 The MODEL NUMBER of the product WG89250 2 The NAME of the product WEIDER 8925 Hard Drive System 3 The SERIAL NUMBER of the product see the front cover of the manual 4 The KEY NUMBER and DESCRIPTION of ihe part s from the PART LIST EXPLODED DRAWING accompany ing this owner s manual LIMITED WARRANTY Weider Inc WEIDER warrants this product to be free from defects in workmanship and material under normal use and service conditions for a period of ninety 90 days from the date of purchase This warranty extends only to the original purchaser WEIDER S obligation under this warranty is limited to replacing or repairing at WEIDER S option the product at one of its authorized service centers All products for which warranty claim is made must be received by WEIDER at one of its authorized service centers with all freight and other transportation charges prepaid accompanied
19. nd the VAF SIDE GUARD 46 to each of the Shroud Brackets 30 First assemble the ARM PRESS SHROUD BRACKET 136 to each of the GUARDS 42 and 46 USING TWO 1 2 SELF TAP PING SCREWS 133 Next attach the LY SHROUD BRACKET 149 to each of the GUARDS 42 and 46 using two 1 2 SELF TAPPING SCREWS 133 Attach the U SHROUD BRACKET 52 to the GUARDS 42 and 46 using four WZ SELF TAPPING SCREWS 133 Finally assemble the BASE SHROUD BRACKETS 20 to each of the GUARDS 42 and 46 using two 1 2 SELF TAPPING SCREWS 133 with each Bracket 136 E C p al A 13 3 16 Lu B 123 4 d c 3uz E D 3 4 E 221 7 MEN 1 DNO EPIRI E 133 qu After the Shrouds are in place apply the V Bumpers in the areas shown 133 Boo T33 Weight Resistance Chart rere op 1165 12825 70 70 70 105 935 80B 123 165 80 80 90B 150 165 90 90 90 185 12 0 OLB 200 220 120 130 195 1735 os 223 2565 MO MO 140 210 187 g UJ H H r NO C Po UJ IL ADJUSTMENT The instructions below describe how each part of the hard drive system can be adjusted Refer to the EXERCISE GUIDE accompanying this owner s manual to see how the hard drive system should be set up for each exercise IMPORTANT When attaching the Lat Bar or Nylon Strap make sure that the attac
20. nspect and tighten ail parts each time you use the hard drive systern Replace any worn parts immediately The hard drive system can be cleaned using a SUR cloth and a mild non abrasive detergent Do not use solvents TIGHTENING THE CABLES Woven cable the type of Cable used on the hard drive system can stretch slightly when it is first used If there is slack in the cables before resistance is felt the cables should be tightened Follow the instructions below to lighten the cables Locate the adjustment sleeve and adjustment screw near the lower end of the Pulley Cable 69 Loosen the adjustment screw Pull the end of the Pulley Cable until the Pulley Cable is tight slide the adjustment sleeve and the ball against the low pulley and retighten the adjustment screw Make sure that the cable is not too tight or the top weight on the rear weight stack will ps lifted off the weight stack If the cables cannot be tightened by following the instructions above see the instructions below Remove the 5 16 x 1 1 4 Bolt 2 Weight Bracket 110 and 1 2 x 7 16 Bushing 134 from the Weight Tube 108 in the rear weight stack Remove the Cable Bracket 135 from the Weight Tube Tighten the 1 4 Nut 134 farther onto the end of the Weight Cable 70 Reassemble the parts Repeat if necessary until there is no slack inthe cables Make sure that the cable is not too tight or the top weight on the rear weight stack will be l
21. olt down through the top ofthe Bracket andinto the Welded Tube Assemble a 1 4 FLAT WASHER 6 onto the Bolt and se cure with a 1 4 NYLON LOCK NUT 9 Locate the ARM PRESS SEAT 62 over the SEAT BRACKET 39 and the Welded Seat Tube so that the wide end of the Seat is to the inside of the unit Secure in place using 1 4 X 3 4 SCREWS 7 io bolt up through the Seat Bracket and into the Seat Bolt the front of the Seat to the Welded Tubing using a 1 4 X 2 1 2 SCREW 120 to bolt up through the bottom of the Tubing and into the Seat 10 Position the SQUAT SIDE GUARD 42 and the VAF SIDE GUARD 46 around the Weight Stacks The VAF Side Guard is the Guard with ihe larger opening on one end Orient the VAF Side Guard with ihe large opening to the top and position the Guard on the leg of the BASE 15 with the larger Flat Bracket and X2 Upright Welded Tube Position the Squat Side Guard onthe opposite side of the Weight Stack The Guard will be secured to the unit in a later step VAF SIDE x 2 Ss per e VM Gagner A 2 D QUEUE UE M RENI RE ERRORS TOOT Bee 2 256 ees xDDD Mec D TEENIE eso o Du M uu os WA i UT UAE c o AAA Y ne am Yr SN Roa ALLOW ao Seinen ABIDE ee e EIER rat E gh Cok EU a3 N TETI RIINI x K IER TTR EIT AERTS x x Rene m d es Ao ae tind Sree 2 A A Roache j REE ee ya y AES ey Kae MAN de Se gt 3 NIIP TONERS Spr ree Dm Coweta 4 oe
22. positioning the Bracket with the flat side containing the two holes facing the Front Upright Secure the Bracket with a 8 X 1 2 SELF TAPPING SCREW 133 Assemble the U SHROUD BRACKET 52 to the bottom of the Cross member of the FRONT UPRIGHT 19 positioning the Bracket between the CENTER UPRIGHT 18 and the REAR UPRIGHT 17 Secure the Bracket with a 8 X 1 2 SELF TAPPING SCREW 133 Assemble the ARM UPRIGHT BACKREST 41 to the ARM UPRIGHT 138 by first assembling a 1 4 FLAT WASHER 6 and the ARM PRESS SHROUD BRACKET 136 onto a 1 4 X 2 1 2 SCREW 54 and then bolting through the upper hole location in the of the Arm Upright and into the Backrest Attach the lower Backrest by first assembling a 1 4 FLAT WASHER 6 onto a 1 4 X 2 1 2 SCREW 54 and then bolting through the back of the Upright and into the Backrest Cap each end of the LEFT ARM 27 and the RIGHT ARM 105 with 1 3 4 INNER CAPS 29 Cap the 1 X 2 Welded Tubes on the Arms with 1 X 2 INNER CAPS 114 Press the LEFT ARM 27 and the RIGHT ARM 105 onto the Welded Pivot Tubes on the ARM UP RIGHT MAST 130 making sure to position the Arms with the I X 2 Welded Tubes extended away from the unit Secure the Arms onto the Pivot Tubes with two each I RETAINER RINGS 50 and cap the Tube end with a 1 PLASTIC CAP 51 GREASE NOTE The 1 Retainer Rings are made so that the teeth bend to one side Align the Retainer Rin
23. racket and the Front Upright and tighten the Knob onto the Carriage Bolt ATTACHING AND REMOVING THE MILITARY PRESS SEAT To perform the MILITARY PRESS exercise the Military Press Seat 98 must be attached to the Base 15 Slide the Seat Post 93 into the indicated socket on the Base To perform the SQUAT exercise remove the Seat from the Base ATTACHING AND REMOVING THE SEAT To attach the Seat 31 to the Front Upright 19 align the bracket on the Seat Frame 32 with the indicated tube on the Front Upright 19 Insert a 5 16 x 2 3 4 Bolt 113 through the Seat Frame and the Front Up fight Tighten a 5 16 Knob 11 onto the bolt For some exercises the Seat must be removed To re move the Seat first make sure that the chain is not attached to the Leg Lever Next remove the 5 16 Knob 11 and 5 16 x 2 3 4 Carriage Bolt 113 from ihe Seat Frame 32 and lift the Seat off the Front Upright ATTACHING THE LEG LEVER TO THE LOW PULLEY STATION To use the Leg Lever 33 the Seat 31 musi be attached to the Front Upright 19 see ATTACHING AND REMOVING THE SEAT above Attach one end of the Chain 73 to the Pulley Cable 69 with a Cable Clip 74 Attach the other end of the Chain to the 5 16 x 2 1 2 Eyebolt 37 on the Leg Lever with a Cable Clip 20 g 4 Li m ACE G T e APRES ar eed aic ak Vuemie wt 20 aee iab RARI aM DL x wp Ela ies TROUBLE SHOOTING AND MAINTENANCE I
24. rt No 120912 R694A 1994 Weider Inc mE Printed in Canada i ET nom r paaa Ph airn t
25. semble 5 16 FLAT WASHERS 45 onto the Bolts and then con tinue now to bolt through the Bracket of the Arm Press Selector Secure with 5 16 NYLON LOCK NUTS 4 xt P t B oe at d insert the SHOCK BAR 26 into the LOWER Welded Tube on the PIVOT ARM 75 Center the Bar making sure the slotted side faces the front of the unit Assemble the SHORT ARM SHOCKS 25 onto the Bar and secure using 1 4 X 1 1 4 BOLTS 66 and 1 4 NYLON LOCK NUTS 5 Press 3 4 COVER CAPS 65 onto each end of the SHOCK BAR 26 uM 10 ye iM 8 Attach the SMALL U BRACKET 21 fo the upper end of the LARGE BACKREST 30 with a 1 4 X 3 4 SCREW 7 Ti RM 4 Attach the ADJUSTMENT BRACKET 22 to the lower end of the LARGE BACKREST 30 with a 1 4 x 3 4 SCREW 7 s D Align the holes in the SMALL U BRACKET 21 with the upper hole in the FRONT UPRIGHT 19 Attach the Small U Bracket to the Front Upright with a 5 16 X 2 3 4 BOLT 122 and 5 16 NYLON LOCK NUT 4 Align one of the three sets of holes in the ADJUSTMENT BRACKET 22 with the lower hole in the FRONT UPRIGHT 19 Insert a 5 16 X23 4 CARRIAGE BOLT 113 through the Adjustment Bracket and the Front Upright Tighten a 5 16 KNOB 11 onto the Bolt Pressa 1 1 2 INNER CAP 38 into the end of the SEAT FRAME 32 Attach two SEAT BRACKETS 39 to the top of the SEAT FRAME 32 using 1 4 X 2 1 4 CARRIAGE BOLTS 40 to bolt down throu
26. t the intersection of the Base and STABI LIZER 16 making sure to assemble the open slot in the Center Upright in the direction of the smaller Flat Bracket on the Base Secure with two 5 16 NYLON LOCK NUTS 4 The Weight Stack will have thirteen 10 LB WEIGHTS 107 and one 20 LB WEIGHT 145 However at this time press Into the top of all 26 of the 10 LB Weights and the two 20 LB Weights a WEIGHT BUSHING 146 Note that Weider is cast in the Top of the 10 Lb Weights and Made in Canada in the 20 LB Weight NOTE THAT THE WEIGHT BUSHINGS HAVE A PIN GROVE ALSO AND THIS PIN GROVE SHOULD BE INSTALLED INTO THE WEIGHT PIN GROVE Working with one Weight at a time side thirteen 10 LB WEIGHTS 107 and one 20 LB WEIGHT 145 onto the CENTER UPRIGHT 18 making sure that the cast logos are to the top and that the Pin Groove in the top of each Weight is on the same side of the Center Upright as the open slot insert a 5 16 X 2 1 2 CARRIAGE BOLT 1 through the hole in the top of the WEIGHT TUBE 108 Assemble four ROLLERS 109 onto the Short Pins on the sides of the WEIGHT TUBE 108 making sure that the collar of each Roller is fac ing the Weight Tube See Detail A Slide the Weight Tube down into ihe CENTER UPRIGHT 18 making sure that the Weight Tube is turned so that the threaded end of the 5 16 X 2 1 2 CARRIAGE BOLT 1 is on the same side of the Center Upright as the open slot
27. terature before using the hard drive system B 2 Use the hard drive system on a level surface Cover the floor under the hard drive system for protection 3 inspect and tighten all parts each fime you use the hard drive system Replace any worn parts immediately 4 Keep small children away from the hard drive system at all times 5 Keep hands and feet away from moving parts other than handies 6 Always wear athletic shoes for foot protection 7 Make sure that the cables remain on the pulleys at all times if the cables bind while you are exercising stop immediately and make sure that the cables are on all of the pulleys 8 Never release the arms leg lever military press squat arm ab arm lat bar or on strap while weights are raised The weight will fall with great force 9 The ab arm ana the military press squat arm should never be used at the same time The ab am could hit a person with great force if the the military press squat arm is released suddenly 10 The VKR arms should never be used while one of the weight stations connected to the rear weight stack is being used The feet of the person using the VKR arms could become caught between rnoving weights 11 Always stand on a foot plate when performing an exercise that could cause the hard drive system to tip 12 Always disconnect the lat bar from the hard drive system when performing an exercise that does not use the lat bar 13 I
28. then bolting through the outside of each Arm and the Handles Fasten another 5 16 FLAT WASHER 45 onto the Bolt and secure with a 5 16 NYLON LOCK NUT 4 attach the VAF ARMRESTS 80 to the LEFT and RIGHT VAF ARMS 24 amp 79 by first assembling 1 4 FLAT WASHERS 6 onto four 1 4 X 2 SCREWS 82 and then bolting up through the bottom of the Arms and into the Arm Tests Assemble the VAF BACKREST 86 to the upper VAF UPRIGHT 97 by first assembling 1 4 FLAT WASHER 6 onto tow 1 4 X 2 1 4 SCREWS 54 and then bolt ing through the back of the Up right land into the Backrest 13 Attach the SQUAT SEAT 98 to the top of the SEAT POST 93 using 1 4 X 3 4 SCREWS 7 to bolt up through the bottom on the Seat Post and into the Seat ae Soya ns ies et MISSE SANE MEET TASA MN AN N exe A ERIS SERIE Bes Ss op denne RN ORS s A v J SATS NER e XE RT x AS Sn 2 xS A T ee Ones Renae ONDES oy EROS S ot SA ES dv d X NI EN MS AY T AN SAN NS EDS ONUS 2 X iie S st FRYX N PN BAe Cee AN T MESS NS SRS S2 RTS SOS EES S 2 XN gt PUI SES RAAEN Z AAA As uv 2 SCS NOS eee ARS S ES EN s Arat Assemble the SEAT POST 93 to the leg of the BASE 15 with the large Flat Bracket and the Upright Welded Tube Set ihe Post down into the Tube yes PA SP n MATT I aces X ee Seren ME Ie o 7 Ben oS ES e o 14 Attach the SQUAT SIDE GUARD 42 a
29. using two CABLE CLIPS 74 and the CHAIN 73 Adjust as de sired 9 Press 1 3 4 INNER CAPS 29 into ARM UPRIGHT TOPS FRAME 130 Assemble the ARM UPRIGHT TOP FRAME 130 fo the top of the ARM UPRIGHT 138 making sure to orient the Welded Tubes on the Top Frame on the same side of the of the Upright as the lower Welded Seat Tube Assemble 5 16 FLAT WASHERS 45 onto two 5 16 X 2 3 4 BOLTS 122 and bolt down through the top of the Top Frame and then through the top of the Upright Secure in place with 5 16 NYLON LOCK NUTS 4 Attach the LONGER U BRACKET 85 around and at the top of the REAR UP RIGHT 17 by first assembling a 5 16 FLAT WASHER 45 onto a 5 16 X 3 4 BOLT 154 and then bolting through the Open Slot of the Rear Upright and then through the Bracket Secure with a 5 16 NYLON LOCK NUT 4 Assemble the ARM UPRIGHT 138 onto the previously assembled 5 16 X 2 1 2 CAR RIAGE BOLTS 1 in the BASE 15 behind the REAR UPRIGHT 17 Position the upper Arm Upright into the LONGER U BRACKET 85 Secure the Upright in the Bracket with a 5 16 X 23 4 BOLT 122 and a 5 16 NYLON LOCK NUT 4 Fasten the lower Arm Upright with two 5 16 NYLON LOCK NUTS 4 onto the Carriage Bolts but DO NOT over tighten at this time Press 2 INNER CAP 13 into welded Seat Tube on ARM UPRIGHT 138 Assemble the L SHROUD BRACKET 49 to the bottom of the Cross member of the FRONT UPRIGHT 19
30. with a mal let Attach the other end of the LINK ARM 96 to the Weight Stack on the CENTER UPRIGHT 18 by first assem bling a 1 2 X 7 16 BUSHING 134 followed with a 5 16 FLAT WASHER 45 onto the previously assembled 5 16 X 2 1 2 CARRIAGE BOLT 1 in the Weight Tube atop of the Weight stack Next assemble the WEIGHT BRACKET 110 onto the Bolt orient ing the J Hook on the Bracket into ihe Pin Groove under the top WEIGHT 145 Insert a WEIGHT SE LECTOR PIN 112 into one of the Pin Grooves in the Weight Stack As semble another 5 16 FLAT WASHER 45 onto the Bolt followed with a 1 2 X 1 4 BUSHING 44 Next as semble the Link Arm onto the Bolt and secure with a 5 16 FLAT WASHER 45 and 5 16 JAM NUT 137 19 SUAM i Dont de E ee SN a GREASE LOWER WELDED PIVOT TUBE GREASE Assemble FOAM GRIPS 56 onto MILI TARY PRESS ARM 87 Press 1 1 4 ROUND CAPS 140 into the MILITARY PRESS ARM 87 handles Press two 3 8 BUSHINGS 90 into the end of the MILITARY PRESS ARM 87 Assemble the MILITARY PRESS ARM 87 onto the upper Pivot Tube on the VAF UPRIGHT 97 by assembling the Arm in through the unit from the opposite side of the VAF Upright and through the long slots on the shrouds Assem ble the Arm between the CENTER UP RIGHT 18 and the FRONT UPRIGHT 19 and slide onto the Pivot Tube se cure in place with a 1 RETAINER RING 50 Again the te
Download Pdf Manuals
Related Search