Vivotek PT1111M User's Manual
Contents
1. Turbo speed is the maximum speed the device can obtain and is considered separately because itis not generally a smooth step from high speed to turbo That is going from one speed to the next usually looks smooth and will provide for smooth motion with the exception of going into and out of turbo speed Byte 6 contains the tit speed 6 sec 30 sec Tilt speed is in the range 00 stop to 3F high speed and FF for turbo speed Byte 7 is the check sum The check sum is the sum of bytes excluding the synchronization byte modulo 256 O Extended Commands Home Command 2 Bit4 Bit1 are set to 1 ar me es me ms ome mn f mo Command 2 Reserved o Reservec o Reserved o Down 1 Upt Lena Right Awayso Auto Pan Command 2 Bt2 Bit1 are setto 1 Bt7 Bite Bits Bits Bit3 Bit2 BitT Bto Command 2 Reserved 0 Reservedi0 Reserved 0 Down o Upo Left Right 1 Aways 0 Auto Pan speed is controlled by byte5 Data 1 byte5 1 2sec 2 4 sec 3 6 sec O Example Messages all message values are in hexadecimal Message to send Message Receiver 1 Down turbo speed FF 01 00 10 00 FF 10 Receiver 1 Up high speed FF 01 00 08 00 3F 48 Broadcast Left turbo speed PP 00 00 08 FF 00 08 Note the check sum calculation for the lost Receiver 2 Left slowest speed 2 sec FF 02 00 04 01 00 07 AD Nea is Receiver 10 Home FF OA 002. 1E 00 00 28 oa 00001010 o 20000000 Receiver 254 Auto Pan 5 sec FF FE 00 06 03 00 07 Subtotal 00001010 0A o2 20000010 Receiver 254 Stop FF FE 00 00 00 00 FE Subtotal 00001100C FF mun Broadcast Stop FF 00 00 00 00 00 00 eae Sure Receiver 10 Right turbo speed FF OA 00 02 FF 00 0B oe saon 00001011 08 Final check sum value 6 J Technical Specifications Mode PTA111M PT1121M PTA114H PT1121H Image sensor 1 3 Color CCD 1 3 High resolution Color CCD Picture Elements NTSC 512 492 PAL 512582 NTSC 771 492 PAL 753 82 Horizontal Resolution 380 TV Lines 480 TV Lines H Syne Frequency NTSC 15 734 KHz PAL 15 625 KHz V Sync Frequency NTSC 59 94 KHz PAL 50 KHZ Synchronization Internal Minimum Illumination 4 0 Lux at F2 0 0 5 Lux at F20 Back Light Compensation ON OFF switch Electronic Shuttor AUTO Range 1 50 1 60 1 100 000 sec Auto Gain Control AUTO Flickerless ON OFF switch Optional Video Output 1 Vp p 75 Ohms Tens Standard Gmm F1 8 Option 3 6 8 12 mnvF2 0 Pan Angle 135 13 Pan Speed 2 65 see Tit Angie 80 45 Tit Speed 6 30 sec Control interface RS 485 Address Seting 1 254 Dimensions 75mm 1O5mm W 1 TOMH Weight Net 390g Power 2 DC EMI amp Safety CE FCC Table A Pelco D Protocol Receiver Address Electromagnetic Compatibility EMC Th
3. X VIVOTEK Pan Tilt CCD Camera PT1111M PT1121M PT1111H PT1121H USER S MANUAL Check Pac camera Qceiling Mount Kit Fsg OPower Adaptor OIR Remote Control Optional Optional Switch Seti Default Settings of Switches Switeh 1 Swi O Switch 1 SW1 DIP Swich Saing E Power Status LEDs On Of 12 BC Back Light Compensation Onor 1 3 Receiver for Remote Control OON THE 1 5 Baud Rate Selec Pan Tit Control Protocol Select 7 Termination Setting Rear Bottom e So Power cord socket BLE On Off BLC is disabled under default setting To enable the BLC set the DIP switch SW1 2 to Off position Baud Rate Select DIP Switch Swi SWS 2400 Baud default on Of 4800 Baud on on 9500 Baud of On 19200 Baud On On Pan Tilt Control Protocol Select DIP Switch SWIS SmI Polco D Protocol Or ofr Reserved 1 On of Reserved 2 Of On Reserved 3 On On Termination Setting Terminate the unit farthest from the controller when connecting more than one panititt camera to a single controller Termination is only required for the last camera in the series The default setting of the camera is unterminated SW1 8 at O position To terminate the camera set the DIP switch SW1 8 to On position Switch 2 SW2 The DIP switches SW2 1 SW2 8 here configure the camera s r
4. eceiver address Maximum number of receiver is 254 Refer to Table A for address settings while using Pelco D Type control protocol 1 Attach the mounting kit to the mounting surface 3 Install the camera and push it into place 2 Align the slots located on the bottom of the 4 Firmly hold the camera while plugging in the camera with the screws on the sides of the power cord and video cable ceiling mount kit The format for a message is syte1 Byez eyes Bytes Byes Bytes Bye7 Check Synch Sum Bie Address Command 1 Command 2 Daai Daa2 All values below are shown in hexadecimal base 16 The synchronization byte is always SF The address is the logical address of the receiver driver being controlled Address 00 is broadcast to every device The check sum is the 8 bit modulo 258 sum of the payload bytes bytes 2 through 6 in the message Command 1 and 2 are as follows BRT Bte Bits Bta BRS Bitz Bet Bto Command 1 Reserved 0 Reserved 0 Reserved o Reservec 0 Reserved o Reservedto Reservea o Reservea o Command 2 Reservedio Reserved o Rosorveato Down up Lott Right Always 0 The reserved bits Command 1 Bit7 Bitd Command 2 Bit Bit5 should be set to 0 Byte 5 contains the pan speed 2 sec 85 sec Pan speed is in the range 00 stop to 3F high speed and SFF for turbo speed
5. is device compiles with FCC Rules Part 15 Operation is subject to the following two conditions This device may not cause harmful interference and This device must accept any interference received including interference that may cause undesired operation VIVOTEK isicscce ser necrniee EK esc AEE U onon emma
Download Pdf Manuals
Related Search