Vision Fitness X6850HRT User's Manual
Contents
1. Insert the plastic connector to the inside duataction arm cover Slide the outside dualaction arm cover onto the other end of the plastic connector Secure the outside dualaction arm cover to the bottom of the dualaction arm with a bolt W s SU Tighten both bolts with the screwdriver Repeat these steps on the left side e Slide the accessory tray onto the console mast Secure in place with four panhead bolts M8x20l Tighten with the 5mm Lshaped wrench e Remove the four bolts M5x12L from the back side of the console Connect the data cable and the heart rate wires to the plugs in the back side of the console Place the console on the mast and secure in place with the bolts M5x1 21 e Place the X685OHRT in its intended location and plug in the power cord to the electrical outlet2. Screwdriver TOOLS amp PARTS INCLUDED bmm TShaped Wrench PARTS BOX C Power Cord Console Mast Bracket Console Mast Cover Accessory Tray Color coded Hardware Bags Owner s Guide Assembly Guide Warranty Card 13mm Wrench 6mm LShaped Wrench a D 5mm LShaped Wrench 17mm Wrench 8mm LShaped Wrench 500 South CP Avenue P O Box 280 Lake Mills WI 53551 toll free 800 335 4348 phone 920 648 4090 fax 920 648 3373 www visionfitness com Fitness All Rights Reserved 3 08 K 4 Guide X6850HRT COMMERCIAL INCLINE ELLIPTICAL TRAINERS X6850HRT COMMERCIAL INCLINE ELLIPTICAL TRAINERS To avoid possible damage to this Elliptical Trainer please follow assembly steps in the correct order Before proceeding find your new Elliptical Trainer s serial number located on the front axle tube and enter here Refer to this number when calling for service and enter this serial number on your Warranty Card and in your own records Be sure to read your Owner s Guide before using your new Elliptical Trainer If any parts hardware or tools are missing please call 1 800 335 4348 Extension 12 NOTE It is recommended that you apply grease to the threads of each bolt and screw as you assemble your Elliptical Trainer to prevent loosening and noise Also during each assembly step ensure that ALL bolts and screws are in p
3. lace and partially threaded in before completely tightening any ONE bolt or screw HARDWARE INCLUDED Cr L RK L ea E an ei JN W WL 1 M8 Lock Washer 8x16x2T Washer M10 lock Washer KE Quantity 4 Quantity 4 Quantity 4 M10x251 Socket Head Bolt N L Gene 4 O E iT ey L LU Zip Tie Quantity 1 M8x25L Socket Head Bolt Quantity 4 K BLUE BAG SM ao am O Ol M5x12L Bolt Seef MIO Nylon Nut Quantity 2 10x24 5x1T Washer Quantity 2 Quantity 4 A Ne C M10x55L Socket Head Bolt Ke Quantity 2 a HARDWARE INCLUDED ORANGE BAG K CC mm Geh 2 E TD 71 M8x20L Socket Head Bolt Quantity 4 8 2x18x1 5T Arc Washer CH Quantity 4 A GREEN BAG 3 Nie JE 26x36x0 3T Wave Washer Quantity 2 ff a A T End Cap illustration not to scale ER Quantity 2 u M8x1 21 Bolt Quantity 2 25 5x38x1T Washer Quantity 2 Y A Ss BLACK BAG O BC Spacer Quantity 4 O H O l J Quantity 2 Lanv Plastic Connector a2 Quantity 4 uw d MS5x15L Bolt Quantity 8 A Iw MBx25L Socket Head Bolt Y i Quantity 8 MB Lock Washer Quantity 8 M8x55L Socket Head Bolt Quantity 2 Sooo keet CO M8x20L Panhead Bolt Quantity 4 Se Pi e Place a piece of
4. llowing step must be assembled in the correct order e Slide one thin metal wave washer 26x36x0 3T one flat washer 25 5x38x11 and one plastic wave washer 26x36x21 onto the axle of the right link arm Slide the axle of the right link arm through the sleeve on the right pedal arm Secure the link arm onto the pedal arm with the plastic wave washer 26x36x2T end cap and bolt M8x1 21 Tighten with the 5mm L shaped wrench e Repeat the step on the left side NOTE With this next step it is helpful to have a second person to hold the dualaction arms in place while you assemble them Take the right duakaction arm and center the holes in the rotation housing on the console mast Secure with four socket head bolts M8x25l and four lock washers M8 Tighten with the 6mm Fshaped wrench e Attach the dualaction arm rotation cover to the dualaction arm center Secure in place with two bolts M5x15l Tighten with the screwdriver e Slide a spacer onto each side of the socket joint located on the end of the link arm Slide the bottom of the dual action arm bracket over the link arm socket and spacers From the outside of the bracket slide the bolt M8x551 through the hole in the bracket and socket joint Secure with a washer 8x16x1T and nylon nut M8 Tighten with the 6mm Tshaped wrench and 13mm wrench e Attach the inside dualaction arm cover onto the bottom of the dual action arm with a bolt M5x151
5. packaging under the front of the unit to aid in assembly of the front foot e Secure the front stabilizer tube to the base frame plate with four socket head bolts M8x20L and four arc washers 8 2x18x1 5T Tighten with the 6mm L shaped wrench Take the right pedal arm and set the roller wheel in the aluminum guide track Slide the opposite end of the pedal arm into the U shaped knuckle bracket Slide a socket head bolt M10x55l with a washer 10x24 5x1T through the hole in the knuckle bracket and pedal arm Fix in place with a washer 10x24 5x1T and nylon nut M10 Tighten with the 8mm L shaped wrench and the 17mm wrench Slide the pedal arm cover over the knuckle joint and fix in place with a bolt M5x1 21 Tighten with the screwdriver Repeat these steps on the left side e Slide the console mast boot onto the console mast e Cut the zip ties holding the cables and wires onto the console mast e Attach the mounting plate to ti bottom of the console mast with four socket head bolts M10x25L and four lock washers M10 Tighten as much as possible with the 8mm L shaped wrench e Mount the console mast on the frame by sliding the guide hole on the mast mounting plate over the guide screw on the front of the frame bracket Place a lock washer D followed by a flat washer 8x16x2T on each of the four remaining socket head bolts M8x25l Insert the bolts to the rear holes but do not com
6. pletely tighten Next insert the bolts to the front holes Tighten all four bolts as much as possible with the 6mm Lshaped wrench Wrap the wire tie that exits the hole at the bottom front side of the console mast around the data cable coaxial cable and TV power cable coming up from the frame Pull the wire tie and all cables up through the top of the console mast e Remove the protective plastic around the cables and data cable e Tuck the coaxial and TV power cables into the console mast NOTE If you have purchased the TV bracket assembly remove the screws from the TV bracket cover located at the front of the console mast and remove the cover Feed the coaxial and TV power cables through the hole at the front of the console mast Insert a zip tie through the hole in the middle of the console plate and loop it around the heart rate wires and data cable Pull to snug but do not over tighten TV Bracket Cables Data Cable Heart a Wires j Knuckle Bracket Front Stabilizer Tube Console Plate Console Console Mast Console Mast Boot Frame Bracket Accessory Tray Rotation Housing T End Cap Plastic Wave P Washer E A Es e Fa Plastic Wave Washer A Flat Washer Thin Metal Wave Washer S Remove protective covers from sleeves of the pedal arms IMPORTANT The washers in the fo
Download Pdf Manuals
Related Search