Vision Fitness X6000DA User's Manual
Contents
1. X6000DA amp X6200HRT DA DUAL ACTION ELLIPTICAL TRAINERS X6000DA MR X6200HRT DA dual action elliptical trainers To avoid possible damage to this Elliptical Trainer please follow these assembly steps in the correct order Before proceeding though find your new Elliptical Trainers serial number located on the front foot axle tube and enter here Refer to this number when calling for service and also enter this serial number on your Warranty Card and in your own records Be sure to read your Owner s Guide before using your new Elliptical Trainer If any parts hardware or tools are missing please call 1 800 335 4348 Extension 12 NOTE It is recommended that you apply grease to the threads of each bolt as you assemble your Elliptical Trainer to prevent loosening and noise Also during each assembly step ensure that ALL nuts and bolts are in place and partially threaded in before completely tightening any ONE bolt TOOLS HARDWARE amp PARTS INCLUDED 5 Allen Wrench 13 Wrench Screwdriver 5 l Shaped Wrench PARTS BOX Rear Folding Axle Qty 1 0 Stabilizer w Rubber Cover Qty 2 Toe Pieces Qty 2 9 Rear Wheels Qty 2 Tension Control Knob Qty 1 Model X6000DA only Console Qty 1 Power Supply Qty 1 XK6200HRT DA only 13 Cap Qty 2 Water Bottle amp Bracket Qty 1 Heart Rate Chest Strap Qty 1 Model X6200HRT DA only Parts Bags O2. large flat washer M8 onto the righthand side of the rear axle and secure with a bolt M8 x 16 Repeat above steps to install left hand pedal arm guide rail e X6200HRT DA only Slide the toe piece onto the pedal arm while simultaneously lifting the locking knob lock the toe piece into place at the STEP or GLIDE position Mount the rear pedal arms to front pedal arms using four bolts M8 x 80 and four M8 Nylock nuts Tighten with the 13 wrench X6000DA only Install the foot toe pieces to the front pedal arms with two bolts M8 x 45 using the Blue sw Allen wrench X6000DA Only STEP 4 GREEN BAG e X6000DA only Unfold the RPM sensor wire located in the frame console mast bracket Remove any kinks e All models Slide the rubber conso mast cover onto the bottom of conso mast and slide it up as far as it will go e All models Unfold the console cab and attach it to the string located at th bottom of the console mast Guide th wire up through the mast while simultaneously sliding the console mast onto the frame bracket e All models Bolt the console mast to the frame bracket with two bolts M8 x 60 two flat washers M8 and two lock washers MB Tighten with the Blue 5 Allen wrench Slide the rubber console mast cover back down over the bolt heads X6000DA NOTE Be sure the RPM sensor wire exits through the small slot at the t
3. op right side of the console mast X6000DA only Install the batteries in the console Mount console to onsole mast using the four screws ug the RPM sensor wire into the ack of the console and feed the xcess back down into the small slot in the console mast e X6000DA only Turn the tension knob to Level 15 Reach inside the console mast and connect the magnet cables Turn the knob to Level 1 an mount the knob using a bolt M5 x 25 X6200HRT DA only Remove the four screws from the back of the console Plug the wire connector from inside the mast into the console The cable connector is slotted so it may only be connected one way do not force it e X6200HRT DA only Mount console to the mast using the four screws Do not pinch the cable X6000DA Only e All models Bolt the water bottle cage to the console mast using the two bolts located in the mast STEP 5 BLACK BAG Slide a large wavy washer M26 onto the console mast axle Locate and slide the right upper handlebar bracket onto the console mast axle and attach with a washer M8 x 35 and M8 Nylock nut using the 13 wrench Snap the plastic 13 nut caps over the nuts e Slide a small wavy washer M16 onto the lower pedal arm support followed by the right lower arm Attach with a washer M8 x 25 and bolt M8 x 12 using the Blue 5 Allen wrench Pivot the lower arm and insert the top end in
4. to the upper handlebar bracket Attach with bolts M7 x 35 and x 12 through the side and bolts M8 x 12 from the front Tighten using the Blue 5 Allen wrench Repeat the above steps to attach left hand upper and lower arms 621 D East Lake Street P O 280 Lake Mills WI 53551 toll free 1 800 335 4348 phone 1 920 648 4090 fax 1 920 648 3373 www visionfitness com 2001 Vision Fitness All Rights Reserved 4 01 Part Z60EP08 AG1801PRD AG18 01PRD U S Patent No 6 190 289 REV3
5. wners Guide Assembly Guide Warranty Card M8 x 45 Bolt Quantity 2 X6000DA only 8 x 80 Bolt Quantity 4 8 Nylock Nut Quantity 4 KM 8 x 16 Bolt Quantity 4 GREEN BAG BLUE BAG M8 lock Washer ma mm O Quantity 2 8 x 16 Bolt M16 Wavy Washer Quantity 2 Quantity 2 M8 Washer Quantity 2 CD mm 5 x 25 Bolt M16 Washer M8 Washer Quantity 1 8 x 60 Bolt Quantity 2 Quantity 2 X6000DA only Quantity 2 BLACK BAG o M8 x 25 Washer M16 Wavy Washer Quantity 2 Quantity 2 A x 12 Bolt Quantity 2 OU G Wm u Quantity 2 M8 x 35 Washer M26 Wavy Washer 8 x 12 Bolt Quantity 2 Quantity 2 Quantity 4 8 x 36 Bolt Quantity 2 e Install the left and right stabilizers wit the four bolts M8 x 16 using the Blue 5 Allen wrench e Cover both stabilizers with the included rubber covers Insert the rear folding axle shaft int rear tube STEP 2 BLUE BAG e Slide a wavy washer M16 onto the righthand side of the rear folding axle followed by the righthand pedal arm guide rail the guide rails each have a blue indicator arrow printed on their sides these arrows should face to the outside e Slide a flat washer M16 onto the righthand side of the rear axle followed by a rear wheel e Slide the
Download Pdf Manuals
Related Search