Vision Fitness T9200 (TM186) User's Manual
Contents
1. M4 x 121 Panhead Screws Quantity 4 M8 x 135L Bolts Quantity 4 Slide the rubber covers on to the left amp right console supports making sure that the lower cutout is facing inward T9700 Slide the data cable down the right console support using the white wire tie as a guide Make sure that the data 1 large ribbon cable goes through the large hole in the lower part of the console upright T9200 T9500 T9600 Slide the data cables down the right console support using the white wire tie as a guide Make sure that the data cables one small amp one large telephone style cable go through the large hole in the lower part of the console upright Insert the left console support into the console support bracket and secure with two bolts 8 x 551 Flathead in the side of the console support bracket Insert one bolt 8 x 201 in rear of the console support bracket Tighten all three bolts with the 5mm Allen wrench Repeat this on the right side NOTE There are no data cables on the left side BLUE BAG Mount the console to the console mast using four bolts M8 151 and tighten with the 5mm Allen wrench NOTE Push all extra data cable into the console mast Make sure not to pinch or cut the data cable Mount the righthand side mount handlebar to the console mast using two bolts M8 x 1351 Repeat this on the lefthand side MODELS T9200 T9500 amp2. T9200 T9500 T9600 AND T9700 PLATFORM TREADMILLS Assembly Guide T9200 T9500 T9600 AND T9700 PLATFORM TREADMILLS To avoid possible damage to this Platform Treadmill please follow these assembly steps in the correct order Before proceeding though find your new Platform Treadmills 2 serial numbers located on the underside of the main frame and on the bottom of the console and enter here Frame Serial Number Console Serial Number Refer to these numbers when calling for service and also enter these serial numbers on your Warranty Card and in your own records Be sure to read your Owner s Guide before using your new Platform Treadmill If any parts hardware or tools are missing please call 1 800 335 4348 Extension 12 NOTE It is recommended that you apply grease to the threads of each bolt as you assemble your Platform Treadmill to prevent loosening and noise Also during each assembly step ensure that ALL nuts and bolts are in place and partially threaded in before completely tightening any ONE bolt TOOLS HARDWARE 4 PARTS INCLUDED 5mm LShaped Wrench 8mm Allen Wrench Screwdriver 5 BOX Water Bottle Qty 1 Safety Magnet Key Qty 1 except T9700 Colorcoded Hardware Bags HARDWARE INCLUDED a Crm 511113 8 151 Bolts Quantity 4 M8 201 Bolts Quantity 2 8 x 551 Flathead Bolts Quantity 4 E
3. T9600 Plug in the small data cable into the small plug connection on the lower control board Plug in the large data cable into the large plug connection on the lower control board Slide down the rubber covers on the left amp right console supports MODEL T9700 Plug the large 20ribbon cable into the 20 connection on the lower control board Slide down the rubber covers on the left amp right console supports Install the motor cover making sure that the rubber covers are inserted into the motor cover Secure the motor cover using the six x 121 screws see Yellow bag STEP 4 MODEL CONFIGURATION amp AUTO CALIBRATION Once the Treadmill is plugged in you need to configure the Treadmill and perform an auto calibration to assure maximum performance 97005 amp 7 Z00HR7 CONSOLES DO NOT STAND ON THE BELT WHEN PERFORMING THE AUTO CALIBRATION Once the treadmill is plugged in you will need to configure and run auto calibration With the safety key in place turn the treadmill on A setup screen should appear on the console Set your treadmill to the correct model number 9700S or 9 using the ELEVATION arrow keys and the correct units MI miles KM kilometers using the SPEED arrow keys If you are unsure of the model number you can locate the number on the front of the console Once you have located the model number and units with the arrow keys press and hold SELECT Now you can perfo
4. You need to access Engineering Mode to configure and auto calibrate your treadmill With the safety key in place please hold down ELEVATION UP and SPEED DOWN for 5 seconds NONE will appear in the data window Press the UP arrow key until ENG 1 appears in the data window Press SELECT A number will appear in the speed window Use the SPEED arrow keys to select your treadmill configuration 42 T9500 MI miles 43 T9500 KM kilometers 44 T9600 45 T9600 KM 46 T9200 47 T9200 KM If you are unsure of the model number you can locate the number on the console masts Press SELECT fo enter your configuration Update will flash on the console Press the ELEVATION UP arrows to P14 Eng Out Press STOP Press the UP arrow key ENG 4 This is auto calibration Press SELECT To begin auto calibration press START The treadmill will run through minimum and maximum speed and maximum incline The auto calibration will take 3 5 minutes Let the treadmill perform this complete function before exiting the Engineering Mode END will appear in the center window when auto calibration is complete When auto calibration is complete it will take the treadmill about seconds to go to O elevation and return to the startup screen with P1 showing in the function window SIMPLE CONSOLE DO NOT STAND ON THE BELT WHEN PERFORMING THE AUTO CALIBRATION Once the treadmill is plugged in you will need to c
5. clockwise V 4turn at a time until the belt remains centered during use VISIONSK FITNESS 500 South P Avenue 280 Lake Mills WI 53551 toll free 1 800 335 4348 phone 1 920 648 4090 fax 1 920 648 3373 www visiontitness com 2005 Vision Fitness All Rights Reserved 5 05 Part 292TM186 AG AG18 12PRD REV8
6. onfigure and run auto calibration With the safety key in place turn the treadmill on A setup screen should appear on the console The large LED window displays the model number and the small LED window displays the units Set your treadmill to the correct model number 9200 9500 or 9600 using the ELEVATION arrow keys and the correct units O for miles and 1 for kilometers using the SPEED arrow keys If you are unsure of the model number you can locate the number on the console masts Once you have located the model number and units with the arrow keys press and hold SELECT Now you can perform auto calibration by pressing START The treadmill will run through minimum and maximum speed and elevation This will take 3 to 5 minutes Let the treadmill perform this complete function END will appear in the window when auto calibration is complete When auto calibration is complete it will take about 30 seconds for the treadmill to reboot and return to the startup screen BELT TENSION f the running belt slips when used use the supplied 8mm Allen wrench t turn the and right tension bolts clockwise 4turn at a time until the belt no longer slips f the running belt is too far to the right side use the supplied 8mm Allen wrench to turn the right tension bolt clockwise at a time until the belt remains centered during use If the running belt is too far to the left side turn the left tensi bolt
7. rm auto calibration by pressing START The treadmill will run through minimum and maximum speed and elevation This will take 3 to 5 minutes Let the treadmill perform this complete function END will appear when auto calibration is complete When auto calibration is complete it will take about 30 seconds for the treadmill to reboot and return to the startup screen PREMIER CONSOLE DO NOT STAND ON THE BELT WHEN PERFORMING THE AUTO CALIBRATION Once the treadmill is plugged in you will need to configure and run auto calibration With the safety key in place turn the treadmill on A setup screen should appear on the console Set your treadmill to the correct model number 9200 9500 or 9600 using the ELEVATION arrow keys and the correct units miles KM kilomelers using the SPEED arrow keys If you are unsure of the model number you can locate the number on the console masts Once you have located the model number and units with the arrow keys press and hold SELECT Now you can perform auto calibration by pressing START The treadmill will run through minimum and maximum speed and elevation This will take 3 to 5 minutes Let the treadmill perform this complete function END will appear when auto calibration is complete When auto calibration is complete it will take about 30 seconds for the treadmill to reboot and return to the startup screen DELUXE CONSOLE DO NOT STAND ON THE BELT WHEN PERFORMING THE AUTO CALIBRATION
Download Pdf Manuals
Related Search