ViewSonic VG700B User's Manual
Contents
1. VG700 VG700b 17 Compliance Information for U S A This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help FCC Warnin To assure continued FCC compliance the user must use grounded power supply cord and the provided shielded video interface cable with bonded ferrite cores If a BNC cable is going to be used use only a shielded BNC 5 cable Also any unauthorized changes or modifications not expressly approved by the party responsible for compliance2. USA ua adek UL Switzerland SEV Canada CSA Britain BASE BS Germany VDE Japan Electric Appliance Control Act IMPORTANT NOTICE CONCERNING POWER CORD SELECTION The power cord set for this unit has been enclosed and has been selected according to the country of destination and must be used to prevent electric shock Use the following guidelines if it is necessary to replace the original cord set or if the cord set is not enclosed The female receptacle of the cord set must meet IEC 60320 requirements and may look like Figure A1 below Figure A1 Figure A2 For the United States and Canada In the United States and Canada the male plug is a NEMA5 15 style Figure A2 UL Listed and CSA Labeled For units which are mounted on a desk or table type SVT or SJT cord sets may be used For units which sit on the floor only SJT type cord sets may be used The cord set must be selected according to the current rating for your unit Please consult the table below for the selection criteria for power cords used in the United States and Canada Cord Size of Conductors in Cord Maximum Current Rating of Unit 10 Amps 12 Amps 12 Amps SVT 18 AWG 10 Amps 17 AWG 12 Amps For European Countries In Europe you must use a cord set which is appropriate for the receptacles in your country The cord set is HAR Certified and a special mark that will appear on the outer sheath or on the i
3. changing the refresh rate in your graphic card s user guide If necessary make small adjustments using H POSITION and V POSITION until the screen image is completely visible The black border around the edge of the screen should barely touch the illuminated active area of the LCD display ViewSonic VG700 VG700b 8 Main Menu Controls Adjust the menu ites shown below by using the up a and down vw buttons Control A Explanation Auto Image Adjust automatically sizes centers and fine tunes L L the video signal to edimi nate waviness and distortion Press the 2 button to obtain a sharper image NOTE Auto Image Adjust works with most common video cards If this function does not work on your LCD display then lower the video refresh rate to 60 Hz and set the resolution to its pre set value Contrast adjusts the difference between the image background black leva and the foreground white leva Brightness adjusts background black leva of the screen image Audio Menu controls are explained bd ow Volume increases the volume decreases the volume and mutes audio Mute temporarily silences audio output Color Adjust provides several color options preset color temperatures and Custom User Color which allows you to adjust red R green G and blue B The factory setting for this product is 6500K 6500 Ke vin 9300K Adds blue to the screen image for cooler w
4. display contains high voltage parts You may Do not place heavy objects on the LCD be seriously injured if you touch them display video cable or power cord Avoid exposing your LCD display to direct If smoke abnormal noise or strange odor is sunlight or another heat source Orient your present immediately switch the LCD display LCD display away from direct sunlight to off and call your dealer or ViewSonic It is reduce glare dangerous to continue using the LCD display Always handle your LCD display with care when moving it ViewSonic VG700 VG700b 3 Quick Installation Optional For instructions on wall mounting see page 5 of this user guide 1 Connect power cord and AC DC adapter 2 Connect video cable Make sure both the LCD display and computer are turned OFF e Connect the video cable from the LCD display to the computer Macintosh users Models older than G3 require a Macintosh adapter Attach the adapter to the computer and plug the video cable into the adapter To order a ViewSonic Macintosh adapter contact ViewSonic Customer Support 3 Turn ON LCD display and computer e Turn ON the LCD display then turn ON the computer This sequence LCD display before computer is important NOTE Windows 95 98 or 2000 users may receive a message asking them to install the INF file This is on the CD 4 Insert the ViewSonic Wizard CD into the computer s CD drive Follow the on screen in
5. the displayed control Also a shortcut to display the Contrast adjustment control screen Displays the control screen for the highlighted control Also toggles between two controls on some screens Also a shortcut to Auto Image Adjust Power light Green ON Orange Power Saving Power E K q V A E E E LETA E see ES ViewSonic VG700 VG700b 7 Do the following to adjust the screen image 1 To display the Main Menu press button 1 MAIN MENU 4 AUTO IMAGE ADJUST fae prone Pasa lea The line at the bottom of the COLOR ADJUST screen tells you what you can INFORMATION do next Exit this menu or MANUAL IMAGE ADJUST Select the control that is SETUP MENU highlighted MEMORY RECALL EXIT 2 SELECT NOTE All OnView menus and adjustment screens disappear automatically after about 30 seconds This time period is adjustable through the Setup menu and the OSD timeout control described on page 10 2 To highlight a control you want to adjust press a or w to scroll up or down the Main Menu 3 To sadec the highlighted control press button 2 A control screen appears 4 To adjust the control press the up a or down w buttons To save the adjustments and exit the menu press button 1 twice The following tips may help you optimize your display e Adjust your computers graphic card so that it outputs a video signal 1280 x 1024 60 Hz to the LCD display Look for instructions on
6. CD display face down on a towa or blanket Notice the four screw holes on the bottom of the base for the wall mount 3 Attach the mounting bracket from the VESA compatible wall mounting kit 100 mm x 100 nm distance 4 AttachtheLCD display to the wall following the instructions in the wall mounting kit ViewSonic VG700 VG700b 5 Using the LCD Display Setting the Timing Mode Setting the timing mode is important for maximizing the quality of the screen image and minimizing eye strain The timing mode consists of the resolution example 1280 x 1024 and refresh rate or vertical frequency example 60 Hz After setting the timing mode use the OnView controls to adjust the screen image For the best picture quality set your LCD display timing mode to VESA 1280 x 1024 60 Hz To set the Timing Mode 1 Seatthe resolution Right click on the Windows desktop gt Properties gt Settings gt set the resolution 2 Se ttherefresh rate See your graphic card s user guide for instructions WARNING Do not set the graphics card in your computer to exceed the maximum refresh rate of 75 Hz doing so may result in permanent damage to your LCD display OSD and Power Button Lock Modes OSD Lock This mode locks all current control settings and prevents access to the control menus until this mode is unlocked e OSD Lock Press and hold 1 and the up arrow a for 10 seconds If any buttons are pressed the message OSD Locked w
7. HER PROPERTY CAUSED BY ANY DEFECTS IN THE PRODUCT DAMAGES BASED UPON INCONVENIENCE LOSS OF USE OF THE PRODUCT LOSS OF TIME LOSS OF PROFITS LOSS OF BUSINESS OPPORTUNITY LOSS OF GOODWILL INTERFERENCE WITH BUSINESS RELATIONSHIPS OR OTHER COMMERCIAL LOSS EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES 2 ANY OTHER DAMAGES WHETHER INCIDENTAL CONSEQUENTIAL OR OTHERWISE 3 ANY CLAIM AGAINST THE CUSTOMER BY ANY OTHER PARTY Effect of state law This warranty gives you specific legal rights and you may also have other rights which vary from state to state Some states do not allow limitations on implied warranties and or do not allow the exclusion of incidental or consequential damages so the above limitations and exclusions may not apply to you Sales outside the U S A and Canada For warranty information and service on ViewSonic products sold outside of the U S A and Canada contact ViewSonic or your local ViewSonic dealer ViewSonic LCD Display Warranty V3 0 Release Date 1 29 2002 ViewSonic VG700 VG700b 16 Appendix Safety Guidelines Warning This device must be operated with the original power supply part number 12V DC LSE0107A1240 12V DC SA125V 3 CAUTION The socket outlet should be installed near the equipment and should be easily accessible CAUTION Use a power cable that is properly grounded Always use the appropriate AC cord that is certified for the individual country Some examples are listed below
8. Viewsonic Contents Product Registration UUEEEEEEEEEUUAUUUUUEE 2 For OUP TYSCORGS ay Jay lk KE iss eal betes 2 Getting Started Package Contents xiii ccescceuseed ite kk kk 3 PRECAUTIONS sssrin irii e a aai 3 Quick Installation EEE 4 Installation of Wall Mount Optional 5 Using the LCD Display Setting the Timing Mode iiiu EEE 6 OSD and Power Button Lock Modes 6 Adjusting the Screen Image E 7 Main Menu Controls ccccccccssseeeeeeeeeeeaesseeeeeeeeeaes 9 Other Information Specificatii S sie lk kaca kinin ab dak kak y benbal ak k ka 12 Troubleshooting e n 13 Customer SUDDOF lu kk 14 Cleaning the LCD Display uUUUUUUUEUL 15 Limited Warranty mk 16 Appendix Safety Guidelines ikkkk eke 17 Compliance Information for U S A 18 CE Conformity for EUroD iik LEE 18 01 02 03 C ViewSonic VG700 VG700b 1 Copyright ViewSonic Corporation 2002 All rights reserved Macintosh and Power Macintosh are registered trademarks of Apple Computer Inc Microsoft Windows Windows NT and the Windows logo are registered trademarks of Microsoft Corporation in the United States and other countries ViewSonic the three birds logo OnView ViewM atch and ViewM eter are registered trademarks of V
9. act ViewSonic ViewSonic VG700 VG700b 12 Troubleshooting No power Make sure power button or switch is ON Make sure A C power cord is securely connected to the DC power supply and the power supply is firmly connected to the LCD display e Plug another electrical device like a radio into the power outlet to verify that the outlet is supplying proper voltage Power is ON but no screen image e Makesure the video cable supplied with the LCD display is tightly secured to the video output port on the back of the computer If the other end of the video cable is not attached permanently to the LCD display tightly secure it to the LCD display e Adjust brightness and contrast e If you are using an Macintosh older than G3 you need a Macintosh adapter Wrong or abnormal colors If any colors red green or blue are missing check the video cable to make sure it is securely connected Loose or broken pins in the cable connector could cause an improper connection Connect the LCD display to another computer If you have an older graphics card contact ViewSonic for anon DDC adapter Control buttons do not work e Press only one button at atime ViewSonic VG700 VG700b 13 Customer Support For technical support or product service see the table below or contact your reseller NOTE You will need the product serial number Country Region United States viewsonic com T 800 688 6688 service us sup
10. ate Product disposal at end of product life ViewSonic is concerned about the preservation of our environment Please dispose of this product properly at the end of its useful life Your local waste disposal company may provide information about proper disposal ViewSonic VG700 VG700b 2 Getting Started Congratulations on your purchase of a ViewSonic LCD display Important Save the original box and all packing material for future shipping needs NOTE The word Windows refers to Microsoft Windows 95 98 NT XP 2000 and Me Millennium Package Contents IMPORTANT Save all packing material Your LCD display package includes e LCD display e Power cords e Audio cable e Video cable VGA AC DC Adapter ViewSonic Wizard CD ROM NOTE TheCD jacket contains the Quick Start Guide and the CD includes User Guide PDF files and INF ICM display optimization files The INF files ensures compatibility with Windows operating systems and the ICM file Image Color Matching ensures accurate on screen colors ViewSonic recommends that you install both files Precautions e Sit at least 18 from your LCD display Place your LCD display in a well ventilated display area Do not place anythi ng on your LCD e Avoid touching the screen Skin oils are display that prevents heat dissipation difficult to remove e Ensure the area around the LCD display is Never remove the rear cover Your LCD clean and free of moisture
11. could void the user s authority to operate this device Notice for Japan This is a Class B product based on the standard of the Voluntary Control Council for Interference from Information Technology Equipment VCCI If this is used near a radio or television receiver in a domestic environment it may cause radio interference Install and use the equipment according to the instruction manual CE Conformity for Europe The device complies with the requirements of the EEC directive 89 336 EEC as amended by 92 31 EEC and 93 68 EEC Art 5 with regard to Electromagnetic compatibility and 73 23 EEC as amended by 93 68 EEC Art 13 with regard to Safety ViewSonic VG700 VG700b 18 ViewSonic Corporation
12. hite used in most office settings with fluorescent lighting 6 00K Adds red to the screen image for warmer white and richer red 400K Adds gr n to the screen image for a darker color anol Adds blue and green to the screen image for a darker color Custom User Color Individual adjustments for red green and blue 1 Tosdectcolor R G or B press button 2 2 To adjust selected color press a or v 3 When you arefinished making all color adjustments press button 1 twice ViewSonic VG700 VG700b Control Explanation Information displays the timing mode video signal input coming from the graphics card in your computer See your graphic card s user guide for instructions on changing the resolution and refresh rate vertical frequency VESA 1280 x 1024 60 Hz recommended means that the resolution is 1280 x 1024 and the refresh rate is 60 Hertz Manual Image Adjust controls are explained below H Size Horizontal Size adjusts the width of the screen image NOTE Vettical size is automatic with your LCD display H V Position adjusts horizontal and vertical position of the screen image You can toggle between Horizontal and Vertical by pressing button 2 Horizontal moves the screen image to the left or to the right Vertical moves the screen image up and down Fine Tune sharpens focus by aligning the illuminated text and or graphic characters NOTE T
13. iewSonic Corporation VESA is a registered trademark of the Video Electronics Standards Association DPMS and DDC are trademarks of VESA ENERGY STAR is a registered trademark of the U S Environmental Protection Agency EPA As an ENERGY STAR partner ViewSonic Corporation has determined that this product meets the ENERGY STAR guidelines for energy efficiency Disclaimer ViewSonic Corporation shall not be liable for technical or editorial errors or omissions contained herein nor for incidental or consequential damages resulting from fumishing this material or the performance or use of this product In the interest of continuing product improvement ViewSonic Corporation reserves the right to change product specifications without notice Information in this document may change without notice No part of this document may be copied reproduced or transmitted by any means for any purpose without prior written permission from ViewSonic Corporation Product Registration To meet your future needs and to receive any additional product information as it becomes available please register your product on the Internet at www viewsonic com The ViewSonic Wizard CD ROM also provides an opportunity for you to print the registration form which you may mail or fax to ViewSonic For Your Records Product Name ViewSonic VG700 VG700b Model Number VLCDS23719 1W 3W Document Number A CD VG700 1 A CD VG700b 1 Serial Number Purchase D
14. ill display for 5 seconds e OSD Unlock Press and hold 1 and the up arrow a again for 10 seconds Power Button Lock This mode locks the power of the LCD display in the ON position Power Button Lock Press and hold 1 and the down arrow vw for 10 seconds If the power button is pressed the message Power Button Locked will display for 5 seconds With or without this setting after a power failure your LCD display s power will automatically turn ON when power is restored e Power Button Unlock Press and hold 1 and the down arrow vw again for 10 seconds ViewSonic VG700 VG700b 6 Adjusting the Screen Image Use the buttons on the front control pand to display and adjust the OnView controls which display on the screen The OnView controls are explained at the top of the next page and are defined in Main Menu Control MAIN MENU gt AUTO IMAGE ADJUST CONTRAST BRIGHTNESS A AUDIO MENU LU COLOR ADJUST INFORMATION MANUAL IMAGE ADJUST 21 SETUP MENU O MEMORY RECALL EXIT 2 1 SE L E CT Speaker Displays the Main Menu or exits the control screen and saves adjustments Decreases or increases volume Temporarily silences audio output Main Menu S on page 9 With OnView controls Front Control Panel shown below in detail Speaker Scrolls through menu options and adjusts
15. n wipe the surface Disclaimer ViewSonic does not recommend the use of any ammonia or alcohol based cleaners on the LCD display screen or case Some cherical cleaners have been reported to damage the screen and or case of the LCD display ViewSonic will not be liable for damage resulting from use of any ammonia or alcohol based cleaners ViewSonic VG700 VG700b 15 Limited Warranty VIEWSONIC LCD DISPLAY What the warranty covers ViewSonic warrants its products to be free from defects in material and workmanship during the warranty period If a product proves to be defective in material or workmanship during the warranty period ViewSonic will at its sole option repair or replace the product with a like product Replacement product or parts may include remanufactured or refurbished parts or components How long the warranty is effective ViewSonic LCD displays are warranted for three 3 years for all parts including the light source and three 3 years for all labor from the date of the first consumer purchase Who the warranty protects This warranty is valid only for the first consumer purchaser What the warranty does not cover 1 Any product on which the serial number has been defaced modified or removed 2 Damage deterioration or malfunction resulting from a Accident misuse neglect fire water lightning or other acts of nature unauthorized product modification or failure to follow instructions supplied with the
16. nsulation of one of the inner conductors AC PLUG CORD PRECAUTIONS FOR THE UNITED KINGDOM FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCKET OUTLET THEN THE PLUG SHOULD BE CUT OFF AND DISPOSED OF SAFELY THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF THE CUT OFF PLUG IS INSERTED INTO AN APPROPRIATE SOCKET If a new plug is to be fitted please observe the wiring code as shown below If in any doubt please consult a qualified electrician WARNING THIS APPLIANCE MUST BE EARTHED IMPORTANT The wires in this mains lead are coloured in accordance with the following code Green and Yellow Earth Blue Neutral Brown Live If the coloured wires of the mains lead of this appliance do not correspond with the coloured markings identifying the terminals in your plug proceed as follows The wire which is coloured GREEN AND YELLOW must be connected to the terminal in the plug which is marked by the letter E or by the Earth symbol or coloured GREEN or GREEN AND YELLOW The wire which is coloured BLUE must be connected to the terminal in the plug which is marked with the letter N or coloured BLACK The wire which is coloured BROWN must be connected to the terminal in the plug which is marked with the letter L or coloured RED If you have any questions concerning which proper power cord to use please consult with the dealer from whom you have purchased the product ViewSonic
17. osh up to 1280 x 1024 1280 x 1024 60 75 1024 x 768 60 70 75 85 Hz 800 x 600 56 60 75 85 Hz 640 x 480 60 75 85 Hz 640 x 400 70 Hz 720 x 400 70 Hz 100 240 VAC 50 60 Hz auto switch 12V DC 3A 337 92 mm H x 270 34 mm V 13 3 H x 10 64 V 329 F to 1049 F 0 C to 40 C 10 to 90 no condensation To 10 000 feet 4 F to 140 F 20 C to 60 C 10 to 90 no condensation To 40 000 feet 410 00 mm W x 421 40 mm H x 191 22 mm D 16 17 W x 16 59 H x 7 56 D 5 3 kg 11 6 lbs UL FCC B ENERGY STAR IC B Doc B CE MPRII NEMKO SEMKO DEMKO FIMKO C UL TCO 99 VG700 TCO 95 VG700b TUV S EPA VCCI BSMI CB IS013406 2 Gost R PCT BZ02 Specifications LCD Type Color Filter Glass surface Input signal Video Sync Compatibility PC Macintosh Resolution Recommended and supported Power Voltage Display area Full Scan Operating Temperature conditions Humidity Altitude Storage Temperature conditions Humidity Altitude Dimensions Physical Weight Net Regulations Power saving On modes Active Off Normal green LED orange LED Preset Timing Mode pre adjusted to VESA 1280 x 1024 60 Hz Warning Do not set the graphics card in your computer to exceed these refresh rates doing so may result in permanent damage to the LCD display 1 Macintosh computers older than G3 require a ViewSonic Macintosh adapter To order an adapter cont
18. port F 909 468 1202 viewsonic com Canada viewsonic com T 800 688 6688 support F 909 468 1202 service ca viewsonic com United Kingdom viewsoniceurope com T 0800 833 648 service eu F 01293 643910 viewsoniceurope com Europe Middle viewsoniceurope com Contact your service eu East Baltic reseller viewsoniceurope com countries and North Africa Australia and New viewsonic com au T 61 2 9929 3955 service au Zealand F 61 2 9929 8393 viewsonic com Singapore India viewsonic com sg T 65 273 4018 service sg ane Southeast F 65 273 1566 viewsonic com sia Other Asia Pacific viewsonic com tw T 886 2 2246 3456 service ap countries F 886 2 8242 3668 viewsonic com South Africa viewsonic com asia T 886 2 2246 3456 service ap F 886 2 8242 3668 viewsonic com ViewSonic VG700 VG700b 14 Cleaning the LCD Display MAKE SURE THE LCD DISPLAY IS TURNED OFF NEVER SPRAY OR POUR ANY LIQUID DIRECTLY ONTO THE SCREEN OR CASE To clean the screen 1 Wipe the screen with a clean soft lint free cloth This removes dust and other particles 2 If still not clean apply a small amount of non ammonia non alcohol based glass cleaner onto a clean soft lint free cloth and wipe the screen To clean the case 1 Useasoft dry cloth 2 If still not clean apply a small amount of anon ammonia non alcohol based mild non abrasive detergent onto a clean soft lint free cloth the
19. product Repair or attempted repair by anyone not authorized by ViewSonic Any damage of the product due to shipment Removal or installation of the product Causes external to the product such as electrical power fluctuations or failure Use of supplies or parts not meeting ViewSonic s specifications Normal wear and tear Any other cause which does not relate to a product defect Ja ODaQA0 9 3 Removal installation and set up service charges How to get service 1 For information about receiving service under warranty contact ViewSonic Customer Support You will need to provide your product s serial number 2 To obtain service under warranty you will be required to provide a the original dated sales slip b your name c your address d a description of the problem and e the serial number of the product 3 Take or ship the product freight prepaid in the original container to an authorized ViewSonic service center or ViewSonic 4 For additional information or the name of the nearest ViewSonic service center contact ViewSonic Limitation of implied warranties THERE ARE NO WARRANTIES EXPRESS OR IMPLIED WHICH EXTEND BEYOND THE DESCRIPTION CONTAINED HEREIN INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE Exclusion of damages VIEWSONIC S LIABILITY IS LIMITED TO THE COST OF REPAIR OR REPLACEMENT OF THE PRODUCT VIEWSONIC SHALL NOT BE LIABLE FOR 1 DAMAGE TO OT
20. ry the Auto Image Adjust See page 9 before using the Fine Tune control Sharpness adjusts the clarity and focus of the screen image Setup Menu controls are explained bel ow Language allows you to choose the language used in the menus and control screens Resolution Notice displays the recommended resolution for this LCD display Enable allows the Resolution Notice to appear on screen Disable will not allow the Resolution Notice to appear on screen OSD Position allows you to move the or screen display menus and control screens ViewSonic VG700 VG700b 10 Control Explanation OSD Timeout sets the length of time an on screen display screen is displayed For example with a 15 second setting if a control is not pushed within 15 seconds the display screen disappears OSD Background 2 nd a lows you to turn the On Screen Display background On or O Memory Recall returns adjustments to the original factory settings if the display is operating in a factory Preset Timing Mode listed in this user guide Exception This control does not effect changes made with the Custom User Color control ViewSonic VG700 VG700b 17 Other Information 17 full 17 viewable diagonal area TFT Thin Film Transistor Active Matrix SXGA LCD 0 264 mm pixel pitch RGB vertical stripe Anti Glare RGB analog 0 7 1 0 Vp p 75 ohms Separate Sync fh 30 82 kHz f 50 85 Hz Up to 1280 x 1024 Non interlaced Power Macint
21. structions Back plate ia AC DC adapter with power cord AC outlet wall socket If your computer does not have a CD ROM drive see Customer Support 1 Wait for the CD ROM to auto start NOTE If the CD ROM does not auto start double click on the CD ROM icon in the Windows Explorer then double click on viewsonic exe 2 Follow the on screen instructions 5 Windows users Set the timing mode resolution and refresh rate Example 1280 X 1024 60 Hz For instructions on changing the resolution and refresh rate see the graphic card s user guide Installation is complete Enjoy your new ViewSonic LCD display To be best prepared for any future customer service needs print this user guide and write the serial number in or Your Records on page 2 See back of LCD display You can register your product online at the website for your region See the Customer Support table in this guide The ViewSonic Wizard CD ROM also provides an opportunity for you to print the registration form which you may mail or fax to ViewSonic Audio cable Video cable Computer power cord ViewSonic VG700 VG700b 4 Installation of Wall Mount Optional To obtain a wall mounting kit contact ViewSonic or your local dealer Refer to the instructions that come with the base mounting kit To convert your LCD display from a desk mounted to a wall mounted display do the following 1 Disconnect Power 2 Lay the L
Download Pdf Manuals
Related Search