Vestax PDX-2000MkII User's Manual
Contents
1. 4 Place the slip mat on the platter Care should be taken to avoid dropping either both the platter or the cabinet NOTE If the player is operated without fixing the screws the platter may not rotate properly Do not plug in to a power outlet until this unit is fully assembled and adjusted Installing the balance Weight DFrom the backend of the tone arm towards the rear panel place the balance weight onto the shaft and turn counter clockwise Refer to the illustration Slip mat D Place the slip mat on the platter Then place a record on top of the slip mat The slip mat is essentially used to give you better control over the spinning of your record That is with the slip mat in place you are able to stop pull or push the record without affecting the rotation of the platter Cartridge Installation D Make sure that you follow the instructions included with your cartridge 2 Connect the lead wires to the respective terminals Industry standard cartridges come with color coded wires Make sure that you match these colors correctly Red Right Channel White L Left Channel Green amp Right Channel Blue L Left Channel NOTE If using a light weight cartridge we suggest the use of the shell weight enclosed PDX 2000MkIl PDX 2000MkIl Pro Top Record disc side Printed side Vestax Bottom Slip surface side PR2. Front Turntable Platter Option Spare Cartridge Stand Center Spindle Tone Arm Height Fixed Screw Balance Weight Option 5 PDX 2000MkIl Power Switch x Dynamic Needle Pressure m Ons Ne Adjustment Knob EP Adapter Holder S MZ K N T N Tone Arm Arm Rest Slip Mat Option PROFESSIONAL E j DIRECT DRIVE TURNTABLE I S FINE PITCH 10 0 S es START STOP Button amp N mem JE Speed Select Button Pitch Control Fader START BRAKE CONTROL Ultra Pitch Fader Detachable Stylus Illumination Jack Reverse Switch Quartz Lock Button Rear Remote control Jack PDX 2000MkIl 228 TTDI NWNUMINNNNW Or pM m 99 6 9 C QU 5 Output Jack AC Cord Ground Terminal BEFORE USE Parts and accessories Before use please check that you have all parts D Main unit e Accessories accompanying this booklet O Spit al Shell weigh 4 Head shell GND cable 5 Balance weight 8 EP adopter Platter screws Screw driver for platter screws 2 Owner s manual ASSEMBLY AND SET UP Turntable Assembly D Place the platter on the center spindle The platter will adjust itself to best fit over the spindle 2 Adjust the positioning of the platter so that the screw holes line up perfectly 3 Screw and tighten accordingly
3. GND CABLE BLACK CABLE Connection c AMP AUDIO MIXER PHONO L Channel PHONO R Channel GND TRMINAL s J The balance weight and cartridge are balanced the tone arm is held horizontal EN JoThe balance weight setting is too light 0000 UU UU US Adjustment of Stylus Puressure PDX 2000MkIl DHold the balance weight with one hand as shown in the drawing and rotate only counter ring to bring the numeral 0 of the ring into alignment with the center line on the tone arm rear shaft NOTE In case the balance weight moved do the adjustment of horizontal zero balance again 2 Turn the balance weight to present the reading on the gauge to the designed stylus force of your cartridge As counter ring moves in step with the balance weight proper stylus pressure can selected by reading the graduated ring directly NOTE The appropriate stylus pressure needs to be set in order to generate the best performance Please refer to the user s manual of the stylus PDX 2000MkII Pro DYNAMIC BALANCE ADJUSTMENT 1 Loosen the dynamic needle pressure adjustment knob and pull it to the position with appropriate needle pressure the tighten the knob Adjustment of Tone arm Height In case of the height of Tone Arm is needed for adjustment it is possible to adjust the height by following the scale of Tone Arm Height Gauge after loosening the Tone Arm Height Fixed Screw
4. The adjustment range is 9mm at the maximum Cartridge height 16mm l L Height adjustment not necessary cartridge height Cartridge height 25mm ies Height adjustment 9mm Max NOTE Be sure to tighten the Tone arm height Fixed screw well The stylus may jump skip if the height setting is not secured Balance Weight Dynamic Needle Pressure Adjustment Knob Loose Close Dynamic Needle Pressure Adjustment Knob Tone Arm Height Gauge a Driver I Tone Arm Height Fixed Screw OPERATION 1 Place a record on the slip mat 2 Switch on the unit using the Power on off switch located on the rear panel 3 Remove the stylus protector if applicable w 4 Start the platter spinning with the START STOP button 7 5 Position the tone arm over the record and gently lower to begin playback 6 Set the playing speed to either 33 1 3 or 45 RPM NOTE When turned on this unit is set to play at 33 1 3 RPM To adjust to a 45RPM speed setting press the 45 RPM button This unit does not use a cue lever system for speed setting s 7 Move the tone arm to the resting position and secure using the tone arm clamp 8 Push the START STOP button to stop the platter from spinning 9 Turn the unit off NOTE Remote Control If the power switch is turned off without pressing the The START STOP functions of the PDX 2000MkIl can be controlled START STOP button the electric
5. X Vestax PROFESSIONAL DIRECT DRIVE TURNTABLE PIDYK ZOOO MIKI PDAS OO MIKI PTO OWNER S MANUAL VESTAX CORPORATION 1 18 16 Wakabayashi Setagaya ku Tokyo 154 0023 Japan Phone 03 3412 7011 Fax 03 3412 7013 E mail info vestax com www vestax com VESTAX Europe Ltd Unit 5 Riverwey Industrial Park Alton Hampshire GU 34 2QL England Phone 0 1420 83000 Fax 0 1420 80040 www vestax co uk CONGRATULATION Thank you for purchasing the Vestax PDX 2000MkII Mkll Pro Professional Direct Drive Turntable Please read this owner s manual carefully so that you Will fully understand all of the special features and enjoy the full use of this product CONTENTS FEATURES NOTES TU A S T S Aa konna Tones arm EIEN nee BEFORE USE ASSEMBLY AND SET UP INSTALLATION AND CONNECTION ee ee ae oe oe 4000 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is
6. action e PROTECTION FOR FEEDBACK The combination of the new A S T S tone arm and high condensed ABS cabinet enables the highest resistance to the feedback e PDX 2000MkII Pro In addition to the above mentioned feature the dynamic balance tone arm system is adopted By improving the trace performance of tone arm playback sound quality becomes better and it makes playback possible even if the disk have some curvature NOTES Before detaching or attaching the headshell be sure to turn the power of the amplifier or mixer off Detaching or attaching of the headshell with the volume control turned up may cause damage to the speakers Do not turn ON the power supply with the turn table platter detached When play is finished be sure to secure the tone arm with the arm clamp After play is finished if the unit is not to be used for some time care should be taken to secure the tone arm to protect the stylus tip For the same reason the stylus protector should also be attached Wipe the headshell terminals from time to time Dust and dirt at the headshell terminals may result in increased HUM noise or intermittent sound Use a soft dry cloth to clean the heashell terminals Dust and dirt should be carefully removed from stylus tip or records Dust and dirt on the stylus tip or record may not only result in deterioration of tone quality but also cause under wear of the record and the stylus tip itself Transportation o
7. and hold system The result of this laborious task has enhanced the turntables potential immensely and is now incorporated into all Vestax professional level turntables The system breaks with ill foundered traditional tone arm logic in order to achieve a high level of non skipping performance especially during hard play scratch Essentially this system focuses on two very separate yet very important inventions One is a short straight arm and the other is the way in which the arm is balanced both vertically and horizontally TH Tracing hold Balance System This system allows for both vertical and horizontal movement which helps the balance of the tone arm When combined with a short straight tone arm the best stability ever is provided for the needle which in turn allows for hard play The tone arm both straight and short is made up of two parts an inner and an outer tube The inner tube brass is housed within an outer tube of aluminum which reduces the effects of howling and also provides a more sensitive pick up Compared with other tone arms on the market the A S T S tone arm reduces howling by approximately 5096 more NORMAL TYPE TONE ARM F Tracking force q F Inside force d F vertical force amp Needle trace The tracking force frictional force generated between the stylus and the record disc makes the inside force P Needle trace The inside force is minimized PARTS
8. can result in a risk of fire or electric shock Object and Liquid Entry Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock Never spill liquid of any kind on the product Servicing Do not attempt to service product yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified personnel Damage Requiring Service Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions a When the power supply cord or plug is damage b If liquid has been spilled or objects have fallen into the product c If the product has been exposed to rain or water d If the product dose not operate normally by following the operating instructions Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation e If the product has been dropped or cabinet has been damaged f When the product exhibits a distinct change in performance this indicates need for service Replacement Parts When replacement parts are required be sure the service technician has used replacement parts specified by the manufacturer or have the same cha
9. H 10 Vestax PIDKe ZAOOO MIKI ULTRA PITCH QUARTZ LOCK SPEED ADJUSTMENT 3 Ultra pitch fader changes the revolution by 50 11 Start Speed You can adjust the starting speed of the platter by adjusting the PDX ZOOO MUI SPEED ADJUSTMENT START dial A clockwise rotation ULTRA PITCH slows down the starting speed whilst an anti clockwise rotation J Plhi ritirrtitdd will speed it up At its maximum setting after pressing the START button the PDX 2000MkII MkIIPro has an amazingly PUN edi quick start up to full speed of around 0 5 seconds Brake Speed As well as being able to change the start speed you can alter PDX 2OOOMIGI the speed at which the platter brakes or slows down A clockwise rotation of this dial gives a slow brake speed whilst an anti clockwise rotation produces the fastest brake speed Eu dates SIME possible Again the powerful motor and therefore platter du ak speed of PDX 2000MKII MKIIPro is far beyond that of its closest competitor Reverse Play When pushed this button will instantly reverse the playing direction of the platter In reverse mode an indicator LED will PIE 220 0X MIKI be on When the unit is first turned on the platter is set to spin ULTRA PITCH in the normal forward direction REVERSE QUARTZ LOCK SPEED ADJUSTMENT BRAKE 12 SPECIFICATION TURNTABLE MO
10. OFESSIONAL EEE DIRECT DRIVE TURNTABLE The slip mat included with this unit may differ from illustrations in this user guide or in other publications NUT SHELL OPTION LEAD WIRE SHELL WEIGHT OPTION TERMINAL ACCESSORY CARTRIDGE ACCESSORY STYLUS ACCESSORY SCREWS ACCESSORY 3 The overhang of your cartridge needs to be adjusted to best suit the A S T S tone arm For best tracking and stylus pressure a distance of 50mm as shown should be set NOTE To avoid premature damage to the stylus take care to avoid touching it during any adjustment s 4 Insert the head shell into the front part of the tone arm Turn the looking ring in the direction shown below until the head shell is firmly fixed in place INSTALLATION AND CONNECTION Power Connection Plug in the unit to a power outlet NOTE This unit has been manufactured to strict quality and safety standards PLEASE ENSURE that you use the correct power supply as shown on the rear panel of this device FAILURE to do so many result in shock and or serious damage to this unit and or users Player Installation Do not expose this unit to direct sunlight or install in an area that is typically humid and or damp Place this unit on a stable horizontal service in order to limit vibration and poor tracing action of the tone arm Locate this unit at a suitable distance from any speakers so as to avoid feed
11. TOR STARTING UP TIME STARTING TORQUE BRAKING SYSTEM RAMBLE S N RATIO SPEED FINE PITCH ULTRA PITCH WOW amp FLUTTER BALANCE TONE ARM HEIGHT STYLUS PRESSURE LIGHT OPTIONAL SPEED LOCK REMOTE DIMENSION WEIGHT POWER DIRECT DRIVE QUARTZ 0 5sec 33 1 3rpm 70 2 kg cm ELECTRONIC BRAKE 78dB IEC 98 WTD 33 1 3rpm 45rpm 10 100mm FADER 50 45mm FADER 0 07 W R M S ANTI SKIPPING TONE ARM SYSTEM DYNAMIC BALANCE STRAIGHT TONE ARM TRACING HOLD BALANCE ADJUSTMENT RANGE 9MM MAXIMUM ADJUSTMENT RANGE 0 7 0g DETOUCHABLE MINI LIGHT DC12Volt 20mA QUARTZ LOCK MOMENTARY START MINI JACK W 454mm X H 162mm X D 365mm 9 5kg AC120V or AC230V 10W 22AZ851010
12. back Interference may result from close proximity of an AM FM tuner Connecting Phono terminal With the RCA cable accessory 7 and the GND cable accessory 8 connect the output terminals and the GND terminal on the PDX 2300 rear panel and the phono input terminals to the respective terminals on your amplifier mixer NOTE z PDX 2000MkIl MkII Pro LUMMMMMM NN NNNSSSSSSSSS pS Ensure that the GND ground terminal is firmly connected to a mixer or amplifier If the GND terminal is not correctly connected HUM may persist PDX 2000MkII MkII Pro 7 MHEARPANEL RCA JACK WHITE L SERIALNG L burur LZ REMOTE re GG EE NN NNNNSSSSSSSSSSSQUN Se y m LLL DJ3 4 PCV180 Pcl 1s0 Vestax Corporation RI MADE IN CHINA ADJUSTMENT S Adjustment of Horizontal Zero Balance D Install the cartridge headshell and balance weight to the tone arm 2 Unlock the arm rest adjust the tone arm balance by rotating the balance weight so that the tone arm stays in horizontal position in balance 3 Put the tone arm on the arm rest and lock it NOTE Please be sure that the needle does not touch the platter or the other object in adjustment procedure CLUE RCA JACK RED R GND TERMINAL V A CABLE Connection t RCA CABLE WHITE L RCA CABLE RED R
13. brake will not externally with equipment such as a foot switch peddle An input function jack is provided for this remote control on the rear panel of this unit Playing EP records Fit the EP adapter over the center spindle and follow the same playing instructions as written above Stylus light Detachable mini light A detachable stylus light is available for this unit as an optional extra 10 Adjustment of Quartz Locked Control and Pitch 1 When the indicator lamp is lit showing the operating condition IPIE ZO MIKI for the pre determined speed 33 1 or 45 rpm ULTRA PITCH 2 During the operation of pre determined speed Pitch control fader not be functioned And once press quartz control Bo Se rod button the indicator lamp is put out the speed can be adjusted pitch control fader 3 During the operation of above 2 if you want to change to speed to the pre detemined one press the quartz button The indicator lamp lights and speed will become pre determined one even when the pitch control fader not in the center Lighting Quartz Lock e Putting out Light Non Quartz Lock Adjustment of Pitch Control D When pressing the quartz lock button quartz lock is off TID OXONII ULTRA PITCH Lllltltl tlt gl gl 1g 1 REVERSE QUARTZ LOCK SPEED ADJUSTMENT STA BRAKE 2 When moving main pitch controller you can adjust the revolutions by 10 FINE PITC
14. d with a polarized alternating current line plug a plug having one blade wider than the other This plug will fit into the power outlet only one way This is safety feature If you are unable to insert the plug fully into the outlet try reversing the plug If this should still fail to fit contact your electrician to replace your obsolete outlet Do not defeat the safety purpose of the polarized plug Power Cord Protection Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to cords at plugs convenience receptacles and the point where they exit from the appliance 13 14 19 16 17 18 19 20 2l 22 Protective Attachment Plug The appliance is equipped with an attachment plug having overload protection This is a safety feature See Instruction Manual for replacement or resetting of protective device If replacement of the plug is required be sure the service technician has used a replacement plug specified by the manufacturer that has the same overload protection as the original plug Lightning For added protection for this product during lightning storm or when it is left unattended and unused for long periods of time unplug it from the wall outlet This will prevent damage to the product due to lightning and power line surges Overloading Do not overload wall outlets and extension cords as this
15. f the unit to distant places for removal and the like Pack up the unit in there verse order to that for unpacking using the packing materials furnished when the unit was purchased Should there be no such packing materials be sure to take the following steps Remove the turntable platter together with the turntable mat and wrap it up to prevent any damage to them Return the tone arm to the armrest and affix it with tape or the like Remove the balance weight and the headshell cartridge from the tone arm and then wrap them up to avoid and damage to them Wrap up the turn table base with a blanket or soft paper also to prevent any possible damage to it ACOUSTIC FEEDBACK AND HUM Acoustic Feedback is usually cause by vibration of speaker which affects the sensitive cartridge If such a phenomenon occurs relocate the turn table or speakers as far apart from each other as possible Hum is usually cause by near by appliances that use transformer or thermostat Relocating be unit further away from the noise sources will readily solve the problem Hum may also be produced if the grounding wire extending from the unit is securely connected to the GND terminal on the amplifier of mixer A S T S Anti Skipping Tone arm System The A S T S Anti Skipping Tone arm System was years in trial and development Initially the quest was to improve on the tracing of tone arms available at the time but soon the quest mutated into designing a completely new tone arm
16. intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE CAUTION TO PREVENT ELECTRIC SHOCK MATCH BLADE OF PLUG TO WIDE SLOT FULLY INSERT ATTENTION POUR EVITER LES CHOCS ELECTRIQUES INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU AU FOND 10 11 12 IMPORTANT SAFEGURDS READ BEFORE OPERATING EQUIPMENT This product was designed and manufactured to meet strict quality and safety standards There are however some installation and operation precautions which you should be particularly aware of Read instructions All the safety and operating instructions should be read before the appliance is operated Retain instructions The safety and operating instructions should be retained for future reference Heed Warnings All warnings on the appliance and in the operating instructions should be adhered to Follow Instructions All operating and use instructions should be followed Cleaning Unplug this product from the wall outlet before cleaning Do not use liquid cleaners or aerosol cleaners Use a damp cloth for cleaning Attachments Do not use attachments not recommended by the product manufacturer as they may cause hazards Water and Moisture Do not
17. racteristics as the original parts Unauthorized substitutions may result in fire electric shock or other hazards Safety Check Upon completion of any service or repairs to product ask the service technician to perform safety checks to determine that the product is in proper operating condition Carts and Stands The appliance should be used only with a cart stand that is recommended by manufacturer An appliance and cart combination should be moved with care Quick stops excessive force and uneven surfaces may cause the appliance and cart combination to overturn FEATURES NEW DESIGNED DC MOTOR Newly designed DC motor creates 1 7kg torque and super fast start and brake within 1 4 rpm ANTI SKIPPING TONE ARM SYSTEM TRACING HOLD BALANCE SYSTEM The heavy duty A S T Stone arm is also newly designed for this model Its stability and elaborateness enables non skipping performance in any occasion New designed A S T S Anti Skipping Tone Arm System and TH tracing hold balance TONE ARM system protect skipping performance in hard scratching And this TONE ARM provide adjustment mechanism of tone arm height which Vestax Turn table series have generally e ULTRA PITCH CONTROLLER 50 Ultra Pitch ControI Fader allows DJs to be more creative START amp BRAKE CONTROL Start amp brake speed control volumes are provided for new mixing technique e REVERSE PLAY Reverse bottan makes platter spin backwards in one quick
18. use this product near water for example near a bath tub wash bowl kitchen sink or laundry tub in a wet basement or near a Swimming pool and the like Accessories Do not place this product on an unstable cart stand tripod or table The product may fall causing serious injury to a child or adult and serious damage to the appliance Use only with a cart stand tripod bracket or table recommended by the manufacturer or sold with product Any mounting of the appliance should follow the manufacturer s instructions and should use a mounting accessory recommended by the manufacturer Ventilation Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating and these openings must not be blocked or covered The openings should never be blocked by placing the product on a bed sofa rug or other similar surface This product should never be placed near or over a radiator or heat register This product should not be placed in a built in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer s instructions have been adhered to Power sources This product should be operated only from the type of power source indicated on the marking label If you are not sure of the type of power supply to your home consult your appliance dealer or local power company Grounding or Polarization This product is equippe
Download Pdf Manuals
Related Search