Vax V-042 User's Manual
Contents
1. Cause No electricity in wall outlet Solution Check fuse or breaker Cause On off switch not turned on Solution Push on off switch to on Cause Motor thermostat has tripped Solution Switch off and unplug cleaner Leave for 1 hour before switching the cleaner back on Cause Blown fuse tripped breaker Solution Reset circuit breaker or replace fuse PROBLEM Cleaner won t pick up Cause Full or clogged dirt container Solution Clean dirt container Cause Wrong pile height setting Solution Adjust carpet height adjuster Cause Clogged nozzle Solution Remove obstruction Cause Clogged dirt inlet Solution Remove power head cover and remove obstruction Cause Clogged hose Solution Remove obstruction Cause Broken belt Solution Replace belt Cause Hose not inserted fully Solution Push hose in securely Cause Dirty filters or debris screen Solution Clean change filters or debris screen PROBLEM Accessories won t pick up Cause Accessories not attached correctly Solution Refer to page 6 and 7 for fitting information PROBLEM Cleaner picks up moveable rugs or pushes too hard Cause Wrong carpet height setting Solution Adjust carpet height adjuster PROBLEM Brushbar does not turn Cause Broken belt Solution Replace belt Cause Belt installed incorrectly Solution Check belt changing and brushbar cleaning 10 7 4 Vax V 041 2 9th qxd 2 23 05 12 34 PM gye 11 Tro2. dirt container and empty Clean the filters Allow the cleaner to cool for approximately 1 hour To re start plug into a wall outlet and switch back on A Fig 5 5 5 Accessories Carry Handle 1 The vacuum cleaner must be in the upright Use the carry handle on the dirt container to move position to raise the brushbar Fig 5 1 the vacuum cleaner from room to room Fig 5 6 pin I Fig 5 6 NOTE Verify that the dirt container is secured in place 6 BEFORE lifting the cleaner 7 m Vax V 041 2 9th qxd 2 23 05 12 34 PM ete 7 Accessories Dirt Container amp Filter Removal amp Replacement Rotating Brushbar Removal amp Replacement Crevice Tool Use the crevice tool for radiators crevices corners baseboards and between cushions Dusting Brush The dusting brush is used for furniture venetian blinds books lamp shades and shelves 6 Dirt Container amp Filter Removal amp Replacement WARNING To reduce the risk of injury from moving parts unplug before servicing NOTE Unplug the cleaner before changing filter NOTE For best performance replace filters annually 1 Press the latch above the dirt container and remove the dirt container from the vacuum cleaner Fig 6 1 3 Hold the dirt container and grasp the top of filter Twist and pull the filter up and out Fig 6 8 Fig 6 3 4 Empty the dirt container completely Fig 6 4 5 Each time the dirt container is emptied the fil
3. tool in to the Cord Release round slot on the front right side of tool caddy Fig 3 8B Turn the quick cord release for easy cord removal Insert the cord into the cord clip Fig 1 1 item 14 this will keep the cord out of the way while vacuuming Fig 4 1 Fig 3 8 Fig 4 1 9 Align the tab on the dirt container lid with the slot on dirt container Push the lid down until it snaps rpet Height A ter into place Fig 3 9 Carpet Heig djuste Turn the carpet height adjuster according to the surface being cleaned Fig 4 2 IMPORTANT For easier adjustment place cleaner in upright position 10 Set the aligning tab on the bottom of the dirt container into the rectangular slot on the vacuum cleaner Fig 3 10A and push until the container clicks into place Fig 3 10B CAUTION The brushbar continues to rotate while the hose is removed or in use and at all times while the vacuum cleaner is on Keep hair loose clothing fingers and all parts of the body away from the brush area while the vacuum cleaner is on The vacuum cleaner must be in the upright position to lift the rotating brushbar off the carpet when using the accessories Vax recommend that the carpet height adjuster is at its highest setting Fig 3 10 Vax V 041 2 9th qxd 2 23 05 12 34 PM eye 6 How to Operate Accessories On off Pedal 2 Remove the hose from the tool caddy Fig 5 2 Plug the cord into the electrical outlet Turn the cle
4. Vax V 041 2 9th qxd 2 23 05 12 34 PM eye 1 Vax Careline Vax 0870 6061248 www vax co uk turbo BAGLESS UPRIGHT VACUUM CLEANER WITH TURBOTOOL Vax Model Number V 041 A Please read carefully before using BAGLESS UPRIGHT VACUUM CLEANER this cleaner Always fully extend Vax Model Number V 042 the mains cable before use 7 a Vax V 041 2 9th qxd 2 23 05 12 34 PM gy 2 Parts Overview 1 Diagram Fig 1 1 NIE AS AE B p 10 11 Hand grip Handle TurboTool V 041 only Flexible hose Dirt container release button Carry handle Dirt container HEPA filter Carpet height adjuster Furniture protect strip Extension tube l i O oo itm _ o Lm CY KQ Z Ai r y M X N Crevice tool inside extension tube Hose clip Cord clip Cord wrap with quick release Long power cord Wheels Handle release pedal On off switch Dusting brush Three 3 screws Slicllol Alla fal Se N a _ 2 Safety Information FOR HOUSEHOLD USE ONLY When using the vacuum cleaner basic safety precautions should always be observed including the following 1 On
5. aner on by pressing the foot pedal located on the back left side of the vacuum cleaner Fig 4 8 A i iy Fig 5 2 3 Choose any of the on board accessories or use the hose alone Simply push the attachment firmly on to the end of the extension tube or hose Handle Release Pedal handle To remove the tool twist and pull apart To release the handle push the handle release pedal gently Fig 5 3 located on the lower left side of the cleaner Fig 4 4 f i z SY prs Tae Extension Tube Floor Carpet Cleaning If additional length is needed use the extension tube and or crevice tool Pull crevice tool out of the extension tube Use the extension tube and crevice tool together or separately Fig 5 4 Move the handle and adjust it to the desired position for A storing the upright or B operating the vacuum cleaner De press the handle release pedal again C to clean under furniture Fig 4 5 Fig 5 4 TurboTool v 041 only The TurboTool fits on the end of the telescopic tubes Motor Thermostat or onto the end of the hose Perfect for cleaning stairs IMPORTANT The motor is equipped with a thermal and upholstery The TurboTool should be pulled cut out If for any reason the vacuum cleaner should backwards for optimum cleaning Fig 5 5 over heat the thermostat will automatically turn the unit off Should this occur unplug the vacuum cleaner from the wall outlet and turn off the switch Remove the
6. e three 3 tabs in the base slots Fig 7 8 2 Place the new belt in the area of the brushbar without bristles Fig 7 5 Fig 7 8 6 Replace all three 8 screws to secure the nozzle guard Fig 7 9 ip Fig 7 9 Vax V 041 2 9th qxd 2 23 05 12 34 PM aye 9 8 Clearing Blockages Clearing Blockages from the TurboTool V 041 only Clearing Blockages WARNING To reduce the risk of injury from moving parts unplug before servicing 1 Rotate the locking ring 180 and turn the TurboToo l over 1 Unwrap the hose from the caddy Remove any Fig 8 4 obstruction Fig 8 1 Fig 8 4 2 Lift the cover off the TurboTool and remove blockage Fig 8 5 Fig 8 1 2 Remove the dirt container and check the dirt container inlet located on the cleaner Fig 8 2 Fig 8 5 Aom pra 3 To re assemble ensure that the tabs are engaged Ke Fig 8 6 Pivot the lower housing closed and rotate Fig 8 2 the locking ring 180 to secure Fig 8 6 3 Remove the nozzle guard by removing the three 3 screws Remove any obstructions Fig 8 3 oO el Fig 8 3 Vax V 041 2 9th qxd 2 23 05 12 34 PM gye 10 Troubleshooting 9 Troubleshooting WARNING TO REDUCE RISK OF PERSONAL INJURY UNPLUG VACUUM CLEANER BEFORE SERVICING PROBLEM Cleaner won t run Cause Not properly plugged into wall outlet Solution Plug in firmly
7. lammable or combustible materials lighter fluid petrol kerosene etc or use in the presence of explosive liquids or vapours Do not vacuum up harmful or toxic material chlorine bleach ammonia drain cleaner etc Do not vacuum up hard or sharp objects such as glass nails screws coins etc Do not use without the filters in place Use extra care when vacuuming on stairs Keep vacuuming area well lit Store the vacuum cleaner indoors in a cool dry area Vax V 041 2 9th qxd 2 23 05 12 34 PM gy 3 Safety Information Use amp Function 19 20 Turn off the switch before unplugging Use only CE approved 13 amp extension cords Non approved extension cords may overheat Care should be taken to arrange the cord so that the cord cannot be pulled or tripped over WARNING Always switch off and unplug the vacuum cleaner from the electrical outlet before assembling opening or emptying the dirt container or before connecting disconnecting the attachments CAUTION The vacuum cleaner is a very powerful unit Before plugging the cord into the outlet make sure the switch is in the off position Hold the vacuum cleaner firmly when starting and in use IMPORTANT If the inlet or hose is blocked switch off the vacuum cleaner and remove the blockage s before re starting the vacuum cleaner IMPORTANT Cleaning filters improves vacuum performance Make sure all filters are replaced back into the vacuum cleaner before u
8. lease recycle where facilities exist Check with your Local Authority or retailer for recycling advice Vax Ltd Kingswood Road Hampton Lovett Droitwich Worcestershire WR9 OQH UK email enquiry vax co uk website www vax co uk Version 1
9. ly use the vacuum cleaner indoors on dry surfaces 2 Turn off the vacuum cleaner controls before connecting to or disconnecting from the mains supply 3 Always unplug the vacuum cleaner before connecting or disconnecting the vacuum hose 4 Close attention is necessary when used by or near children Do not allow children to use as a toy 5 Use only as described in this manual Use only the manufacturer s recommended attachments 6 Do not use the vacuum cleaner with a damaged cord or plug Do not use the vacuum cleaner if it has been dropped damaged left outdoors or dropped into water Return the vacuum cleaner to a Vax Authorised Service Agent or suitably qualified person for examination repair or adjustment 7 Do not pull or carry by the cord Do not use the cord as a handle close a door on the cord or pull the cord around sharp edges or corners Do not run the vacuum cleaner over the cord Keep the cord away from heated surfaces 8 Do not handle the plug or vacuum cleaner with wet hands Do not use outdoors or on wet surfaces 9 Do not put any objects into openings Do not use with any openings blocked and do not restrict air flow Keep all openings free of dust lint hair or anything that may reduce airflow Keep hair loose clothing fingers and all parts of the body away from openings and moving parts Do not pick up hot coals cigarette butts matches or any hot smoking or burning objects Do not pick up f
10. sing This vacuum cleaner is intended for household use only and not for commercial or industrial use PLEASE KEEP THESE INSTRUCTIONS FOR FURTHER USE 3 Use amp Function IMPORTANT Always remove the power plug from the wall outlet before assembling or before removing accessories Tool required Phillips screwdriver Assembling the Vacuum Cleaner 1 Slide the back panel on to the base Fig 3 1 _ Vax V 041 2 9th qxd 2 23 05 12 34 PM ee 4 Use amp Function 2 To secure insert two 2 screws into the front of 5 Insert one 1 screw into the back of the handle the back panel Fig 3 2 and tighten making sure that the handle plug is secure Fig 3 5 Fig 3 5 Fig 3 2 i 6 V 041 only Clip the TurboTool on to the front 3 Place the upper handle on to the top of the of the TurboTool caddy Fig 3 6 cleaner Fig 3 8 Fig 3 3 Fig 3 6 4 041 only Push the handle plug on to the front of the vacuum cleaner Fig 3 4A 7 Wrap the hose around the back of the hose V 042 only Push the blanking plug on to the caddy Fig 3 7 Push the hose tube down into front of the vacuum cleaner Fig 3 4B the right side of the vacuum cleaner Fig 3 7B A 1 i Vax V 041 2 9th qxd 2 23 05 12 34 PM gy 5 Use amp Function How to Operate 8 Slide the dusting brush on to the post on the 4 How to Operate lower caddy with its bristles facing out Fig 3 8A Slide the extension tube crevice
11. ter should be cleaned Tap the filter firmly against the inside of a rubbish bin until the dirt stops falling from the filter Fig 6 5 Fig 6 5 6 Return the filter to the dirt container Push the filter into place to prevent dirt leakage Return the dirt container to the cleaner Fig 6 6 7 Rotating Brushbar Removal amp Replacement TOOL REQUIRED Phillips screwdriver WARNING To reduce the risk of injury from moving parts unplug the cleaner before changing the belt or the rotating brushbar To Remove the Belt 1 Lay the cleaner flat and turn it over to expose the nozzle base The base should lay flat and face upwards To remove the nozzle guard use a Phillips screwdriver to remove the three 3 screws The arrows below show the location of the screws Fig 7 1 mAn al Fig 7 1 Vax V 041 2 9th qxd 2 23 05 12 34 PM eye 8 Rotating Brushbar Removal amp Replacement 2 Pull and lift off the nozzle guard Fig 7 2 3 With the new belt in place pull and slide the brushbar into the nozzle making sure that the end caps are in the correct orientation Fig 7 6A Rotate the brushbar manually to make sure belt is properly aligned Fig 7 6 iG AON N Fig 7 2 3 Lift and remove the brushbar Dispose of the old belt Fig 7 3 To Replace the Belt or Brushbar 1 Slide the belt on to the motorshaft Fig 7 4 5 Secure by aligning th
12. ubleshooting UK Service amp Help Technical Specification PROBLEM Air flow restricted with attachment use Cause Attachment use restricts air flow Solution Check attachment Cause New carpet debris clogging air path Solution Remove obstruction 10 UK Service amp Help 11 Technical Specification Vax Care 0870 6061248 Monday Friday 9 00am to 5 00pm Voltage a ee Wattage 1500W 1700W An answerphone is available out of these hours C ity 3 3 lit Any queries or concerns about using the Vax call the abael y d res max Filters Fibre pre motor filter Vax Careline Calls are charged at the UK national rate Pleated paper HEPA filter Please make a note of the serial number and model Cord length 9 3m number of the carpet cleaner before calling There are Weight 8 1kg over 400 approved Vax Service Agents in the UK For the nearest Service Agent please call the Vax Careline Subject to technical change without notice www vax co uk CE 11 Vax V 041 2 9th qxd 2 23 05 12 34 PM gye 12 EEC STATEMENT OF COMPLIANCE Manufacturer EEC importer Vax Limited hereby on our own responsibility declare that the products V 041 Everyday Turbo V 042 Everyday are manufactured in compliance with the following Safety 73 23 EEC Low Voltage Directive as modified by 93 68 EEC EMC 89 336 EEC Electromagnetic Compatibility Directive as modified by 93 68 EEC Waste electrical products should not be disposed of with household waste P
Download Pdf Manuals
Related Search