Ultra Start MCS-100 User's Manual
Contents
1. 1 Locate the Starter wire Version A MCS 100 2 Use 30 40 Amp SPDT relay to connect as shown Connect the Starter Interrupt output Orange wire to pin 86 of the relay Connect pin 30 of the relay to the Motor side of the Starter wire Connect pin 87a of the relay to the switch side of the Starter wire 3 Locate the Ignition wire 4 Connect the Switched ignition yellow wire and 85 of the Starter Interrupt relay to the Ignition wire To Starter Motor or Relay Yellow Diagram 4 Parking Light Connection 2 Locate the parking light wire or signal wire that switches from Ground to 12V when turning on the parking lights or signal lights usually near the parking light switch Connect the parking light output wire White to the parking light wire of the motorcycle We have two parking light output wires for two separate left amp right controls for the parking lights If there is only one control for the parking lights then connect both white wires to the same parking light If the parking light wire switches from 12V to Ground when turning on parking lights use a 20 30A SPDT relay to invert the control signal polarity Positive Controlled Parking Lights Parking Light Switch White 6 White Parking Lights If alarm doesn t have fuse connect fuse in line for security reasons Negative Controlled Parking Lights Parking Light Switch Ok2. 4 7 Valet Mode The Valet Mode is activated through the ignition key switch and means that all normal system functions are turned off This feature is useful when valet parking refueling or servicing your motorcycle To activate the VALET MODE gt Turn the ignition key to the on position gt gt Within ten 10 seconds PRESS BUTTONS 2 3 2 3 in succession 3 1 2 The valet mode is confirmed with one chirp sound and one parking light flash To deactivate the VALET MODE gt Turn the ignition key to the on position gt gt Within ten 10 seconds PRESS BUTTONS 2 3 2 3 in succession 3 1 2 The operation is confirmed with two chirp sounds and two parking light flashes 4 8 Audible Warning Sound Factory Default Setting Audible Warning Sound On Audible Warning Sound can be permanently enabled and disabled from your remote transmitter To deactivate the AUDIBLE WARNING SOUND gt gt gt Turn the ignition key to the on position Within ten 10 seconds PRESS BUTTONS 1 3 2 1 in succession 3 1 2 The operation is confirmed with one chirp sound and one parking light flash To active the AUDIBLE WARNING SOUND gt gt Turn the ignition key to the on position Within ten 10 seconds PRESS BUTTONS 1 3 2 1 in succession 3 1 2 gt The operation is confirmed with two chirp sounds and two parking light flashes 4 9 Siren Output Tone Selection Your MCS 100 i
3. Turn the ignition key to the on position Within ten 10 seconds PRESS BUTTONS 1 3 1 3 in succession 3 1 2 The operation is confirmed with one chirp sound and one parking light flash Press button 1 of your transmitter to increase the shock sensor sensitivity If you want to increase more than one level of sensitivity press and hold button 1 of your transmitter You will hear 1 chiro sound every 1 seconds At the maximum setting you will hear continuous chirp sounds Press button 2 of your transmitter to decrease the shock sensor sensitivity If you want to decrease more than one level of sensitivity press and hold button 2 of your transmitter You will hear 2 chiro sounds every 1 seconds At the minimum setting you will hear continuous chirp sounds 8 This program mode will exit upon ignition off Cr I ae Turn Ignition Press 1 3 1 3 Press 1 to Press 2 to On in succession increase sensitivity decrease sensitivity GIANNA NO SECTION 5 TRANSMITTER BATTERY REPLACEMENT INSTRUCTIONS Recommended Battery 12V GP23A 1 Remove the screw from the back of the transmitter 2 Remove front cover remove old battery carefully 3 Replace with fresh new battery and close front cover 4 Press any button check for light flash from LED If no LED flash change polarity of battery NOTE normal battery life is approximately two years but varies depending on usage For optimum performance and RF range replac
4. One Time Soft Chirp gt PRESS BUTTON 2 before pressing button 1 for desired operation Example To arm the system with soft chirp sound press button 2 first Then press button 1 Version A MCS 100 4 4 Emergency Disarm The emergency disarm is activated through the ignition key switch and means that the system can be disarmed without remote To activate the EMERGENCY DISARM gt While the system is triggered turn the ignition key on and off four 4 times within ten 10 seconds gt The operation is confirmed with two siren chirp sounds and two parking light flashes NOTE In passive mode if passive armed after disarming by emergency disarm there is entry delay of 10 seconds before triggering by shock or external trigger This mode can be used to operate the system if you lose the transmitter Once the system is armed or disarmed by a remote the entry delay will be cancelled automatically 4 5 Passive Active Mode Factory Default Setting Active Mode Passive mode means that the system automatically arms and interrupts the starter thirty seconds after the ignition key is turned off This assumes that starter interrupt is installed Passive mode is sometimes referred to as Automatic System Activation Active mode means that the system will not engage until you manually turn it on by pressing the remote button 1 Active mode is sometimes referred to as Manual System Activation To program PASSIVE MODE gt Tur
5. Parking Lights Version A MCS 100 SECTION 3 SYSTEM OPERATION The MCS 100 is very sophisticated but the operation is simple Your two button RF transmitter is easy to use for arm disarm personal protection and programming the system for many custom functions 3 1 Remote System Arm On Press and release RF transmitter button 1 One siren chirp sound and a light flash verify the operation O If you hear four chirp sounds the MCS 100 has detected a faulty sensor 3 2 Remote System Disarm Off Press and release RF transmitter button 1 Two siren chirps and two light flashes verity this operation Note If you hear three chirp sounds the system has been triggered and the alarm was activated while you were away from the vehicle Please refer to following chart This diagnostic report will turn off when ignition switch is turned on Audible Chirp Visual LED Shock Sensor Double Flashes Optional Input Trigger Mercury Switch Microwave amp etc Rapid Flashes 3 3 Personal Protection Alarm EMERGENCY PANIC Press and hold down FF transmitter button 1 for approximately three seconds Personal Panic alarm is activated and siren sounds and lights flash for one 1 minute Press and release any RF transmitter button to cancel the panic alarm 3 4 Motorcyle Finder Mode Press and hold down RF transmitter button 3 1 2 for approximately three seconds Lights flash for o
6. E CHANGE MODE is confirmed with one chirp sound and one parking light flash gt Within 3 seconds PRESS BUTTON 1 One chirp and one parking light flash will confirm the acceptance of new code This operation will erase all previous codes gt Within 3 seconds PRESS BUTTON 1 of 2 transmitter One chirp and one parking light flash will confirm the acceptance of second code gt Within 3 seconds PRESS BUTTON 1 of 3 transmitter Once chirp and one parking light flash will confirm the acceptance of third code gt Code program will exit when 3 seconds is passed when ignition is turned off or when all three codes are programmed Note Module will accept three different transmitters 4 2 Permanent Siren Chirp Enable Disable Factory default setting Siren Chirp Enable Siren chirp can be permanently enabled and disabled from your remote transmitter For PERMANENT SIREN CHIRP DISABLE gt Turn the ignition key to the on position gt Within ten 10 seconds PRESS BUTTON 2 for a five 5 seconds gt Siren chirp disable is confirmed with one parking light flash For PERMANENT SIREN CHIRP ENABLE gt Turn the ignition key to the on position gt Within ten 10 seconds PRESS BUTTON 2 for a five 5 seconds gt Siren chirp enable is confirmed with two chiro sounds and two parking light flashes 4 3 One Time Soft Chirp Arm Disarm chirp can be temporarily softened from your remote transmitter For TEMPORARY SOFT CHIRP
7. aaa Installation Manual MCS 100 Remote Control Motorcycle Alarm WWW ULTRASTARTERS COM Technical Support 866 698 5872 ext 0 Support ultrastarters com MCS 100 SECTION 1 SYSTEM LAYOUT White 14 Light Output 20 Amp _ Park or Signal Light Diag 4 Red 15 Amp Fuse 12V DC Power White Light Output 20 Amp 4 Park or Signal Light Diag 4 Black Ground Connect to Battery Ground Green Trigger Input Tilt Switch or Sensor Diag 1 Yellow Ignition Input Ignition Wire Diag 3 Brown LED Output 3V 3V LED Wire Diag 2 oleineiem Starter Interrupt Output Start Wire Diag 3 SECTION 2 SYSTEM CONNECTION Diagram 1 Tilt Switch or External Sensor Connection You can connect any external trigger devices Make sure negative trigger output of external device is connected to Negative Trigger Input Wire Green 4 Optional Tilt Switch Mercury or contact switch Or Optional Shock Sensor 4 Green Or e Optional Motion Sensor Diagram 2 LED Connection 1 Locate a stock replacement part of motorcycle Drill 1 4 hole pull wires through and push LED 2 Connect wires as shown 2 Brown Diagram 3 Starter Interrupt and Ignition Connection
8. e the battery at least once a year O D O KAD _ O ES ae al Padi o aa 10 Old o DO o 9g Step 1 Step 2 Step 3 Step 4 AST 8334 Foothill Blvd Sunland CA 91040 Tel 866 698 5872 Fax 866 418 2042 Version A
9. n the ignition key to the on position gt Within ten 10 seconds PRESS BUTTONS 3 for 5 seconds gt The passive mode is confirmed with one chirp sound and one parking light flash NOTE While in passive mode the system has CONTINUOUS ARMING CONTINUOUS ARMING means that the system will arm thirty seconds after each disarm In passive mode the system can be MANUALLY ARMED anytime during the thirty second automatic locking cycle by pressing remote button 1 To program ACTIVE MODE gt Turn the ignition key to the on position gt Within ten 10 seconds PRESS BUTTONS 3 for 5 seconds gt The active mode is confirmed with two chirp sounds and two parking light flashes 4 6 Shock Sensor Disable Enable Factory Default Setting Shock Sensor Enable The Shock Sensor Disable means that the on board body shock sensor can be eliminated through your transmitter at any time it is desired or necessary To program SHOCK SENSOR DISABLE gt Turn the ignition key to the on position gt Within ten 10 seconds PRESS BUTTONS 1 2 3 1 in succession 3 1 2 gt The shock sensor disable is confirmed with one chirp sound and one parking light flash To program SHOCK SENSOR ENABLE gt Turn the ignition key to the on position gt Within ten 10 seconds PRESS BUTTONS 1 2 3 1 in succession 3 1 2 gt The shock sensor enable is confirmed with two chirp sounds and two parking light flashes Version A MCS 100
10. ne 1 minute Press and release any RF transmitter button to cancel the Motorcycle finder mode SECTION 4 PROGRAMMABLE FEATURES Code Program Method 1 Power On Within 3 seconds press button 1 of new 1 transmitter Press button 1 of 2 transmitter and then press button 1 of 3 transmitter Code Program Method 2 Turn Ignition On Off 5 times Press button 1 of new 1 1 4 1 transmitter Press button 1 of 2 transmitter and then press button 1 of 3 transmitter Permanent Siren Chiro Enable 4 2 2 2 One Time Soft Chirp 4 3 ss Press 2 before other function buttons Emergency Disarm 4 4 Turn Ignition On Off 4 times Alarm will disarm 2 2 Passive Mode Turn Ignition on Press button 3 3 1 2 for 5 ea Active Mode 4 5 seconds Version A MCS 100 Shock Sensor Disable Turn ignition on Within 10 seconds press button 1 2 Shock Sensor Enable 4 6 Valet Mode On Valet Mode Off 4 7 Audible Warning Sound Off Audible Warning Sound On 4 8 Siren Output Tone Selection 4 9 Shock Sensitivity Level Selection 4 10 4 1 Permanent Reprogrammable Factory Code Code Pre Programmed By Factory When the Dealer installs the unit he programs your unique code which is in permanent memory Any Authorized Dealer can add a new or an additional pre coded transmitter and delete an existing code from memory To program a new code gt Turn the ignition key on and off five 5 times gt COD
11. s equipped with 6 tone programmable siren You can select or deselect each tone by your transmitter if desired At the same time you can also determine the sequence of tones To enter the SIREN OUTPUT TONE SELECTION MODE OND MHA wh Turn the ignition key to the on position Within ten 10 seconds PRESS BUTTONS 1 2 1 2 in succession Each of six tones will be on for 5 seconds When you hear the tone you desire press remote button 1 This tone will be your first sequence tone Repeat step 4 for your 2 3 4 5 and 6 tone You may select only 1 tone or any number of tones between 1 to 6 You may also choose not to select any tones This will deactivate the siren completely This program mode will exit upon ignition off or when all six tones are selected in sequence you desire Or Kraso IR Turn Ignition Press 1 2 1 2 Each tone is Press 1 to On in Succession on for 5 seconds select the tone 4 10 Shock Sensitivity Level Selection Your MCS 100 is equipped with programmable dual stage shock sensor You can change sensitivity of shock sensor from your transmitter You can also delete shock sensor by selecting lowest sensitivity level To enter the SHOCK SENSITIVITY LEVEL SELECTION MODE Version A MCS 100 sss _ _ __ elldld C C e E amp gt F F gt F lt lt ooo
Download Pdf Manuals
Related Search