Ultimate Technology 2200 User's Manual
Contents
1. SOFTWARE HARDWARE SERVICE UTC RETAIL 2200 Series POS Bundle 2200 POS Bundle Installation Guide Thank you for selecting UTC RETAIL s innovative 2200 Series Point of Sale bundle solution This guide is designed to help you efficiently assemble the 2200 Series POS Bundle System 2008 UTC RETAIL All rights reserved 11692012 Rev D Page 1 of 12 2200 Series POS Bundle System Installation Guide This guide was prepared by UTC RETAIL to assist personnel with the installation of the bundle components All attempts have been made to ensure that the information presented in this manual is correct No liability expressed or implied will be assumed by UTC RETAIL or affiliates for damage resulting from the use of this information All rights reserved No part of this document may be reproduced stored in a retrieval system or transmitted in any form or by any means electronic or mechanical including photocopying recording or otherwise without the prior written permission of UTC RETAIL If a unit needs to be shipped to UTC RETAIL for repairs please return it in the original packaging material and shipping container If you have questions please call UTC RETAIL s Technical Support at 1 800 349 0546 This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interfere2. hand side of the PC To activate the printer turn on the printer rocker switch located on the front of the printer To activate the monitor depress the on off switch located on the lower right hand side of the monitor bezel You have completed the installation of UTC RETAIL s 2200 Series Bundled Point of Sale System If you experience problems with any of the components of the 2200 Series Bundled POS System see the Troubleshooting Procedures section below O 2008 UTC RETAIL All rights reserved 11692012 Rev D Page 11 of 12 Troubleshooting Procedures The following table presents symptoms and solutions for problems potentially encountered when installing the 2200 Series Bundled POS System components Symptom Solutions There is no image on the LCD monitor Check to see if the monitor power cable is properly connected to the monitor Check to see if the SVGA cable is properly connected to the monitor Make sure that the LCD monitor power is on The printer does not have power Check to see if the printer power cable is properly connected to the printer Make sure that the printer power switch is ON The printer has power but the system does not boot to Windows Push the ATX power button in the front of the logic unit located on the front left hand side of the PC A keyboard error message displays when you boot the 2200 Series POS unit Check to see if the keyboard cable is proper
3. CTOR OPTIONAL AC ADAPTER POWER CONDITIONER WALL OUTLET O AC ADAPTER O 2008 UTC RETAIL All rights reserved 11692012 Rev D Page 8 of 12 12 Connect the optional Customer Pole Display cable to the serial port labeled Com 4 on the back of the PC Figure 9 Rear View of PC IS o o 000 13 Connect the optional Inventory Scanner to a serial port on the back of the PC Then plug the AC power adapter into a wall outlet or the optional Power Conditioner Figure 10 Rear View of PC and Top View of Inventory Scanner E D 2 al OPTIONAL AC ADAPTER POWER CONDITIONER WALL OUTLET O 2008 UTC RETAIL All rights reserved 11692012 Rev D Page 9 of 12 14 Connect a site provided network cable into the network jack on the back of the PC Figure 11 Rear View of PC 15 Plug the PC power cord into the receptacle on the rear of the PC and then into the wall outlet or optional Power Conditioner Figure 12 Rear View of PC E POWER CONDITIONER 2008 UTC RETAIL All rights reserved 11692012 Rev D Page 10 of 12 Powering On Your 2200 Series POS Bundle System Remove the plastic protective sheets from the LCD Monitor and the optional customer display 2 Turn on the ATX PC power by depressing the on off switch located on the front left
4. System 11 Troubleshooting P O Ed E Sn r A AAA A obterces 12 2008 UTC RETAIL All rights reserved 11692012 Rev D Page 3 of 12 Product Information You will find the following components inside the 2200 Series POS Bundle System Box e Safety Sheet e 2200 Series POS unit PC logic device e A C power cord for logic device e LCD Display e Cash drawer e Barcode scanner e POS receipt printer e Keyboard e Mouse Note The following optional items may or may not be present depending on the configuration purchased and may be shipped in a separate box e Magnetic Stripe Reader MSR e Payment Terminal Pin Pad device power supply amp cables e Payment Terminal Signature Capture device power supply amp cables e Customer Display e Inventory Scanner e AC Power Conditioner e Traffic Counter and Door Sensor e Label Ticket Printer 2008 UTC RETAIL All rights reserved 11692012 Rev D Page 4 of 12 Un boxing the System 1 Open the point of sale box and remove the contents 2 Remove all packing materials Installation 1 Orient the cash drawer on its back side on your cash wrap counter Remove the keys Locate the cash drawer cable package labeled APG cash drawer 320 Multipro cable kit Connect the end with the larger modular plug into the jack on the base of the cash drawer Figure 1 Bottom View of Drawer 2 Lay down the cash drawer and place the cable to the side 3 Connect the other end of t
5. he cash drawer cable to the POS printer drawer port labeled DK Figure 2 Bottom View of Drawer PY xy O 2008 UTC RETAIL All rights reserved 11692012 Rev D Page 5 of 12 Connect the printer USB cable from the printer to a USB port on the rear of the PC Connect the power cable from the printer power supply to the connector on the printer Connect the AC cable to the printer power supply and then to a wall outlet or the optional Power Conditioner Figure 3 Rear View of components REAR VIEW OF PRINTER e POWER CONDITIONER WALL OUTLET O Ja eje REAR VIEW OF PC 6 Connect the mouse and keyboard cables to the PC The mouse port on the PC is green and the keyboard port is purple Figure 4 Rear View of PC and Top views of keyboard and mouse ic 000 O 2008 UTC RETAIL All rights reserved 11692012 Rev D Page 6 of 12 7 Remove the LCD LCD VGA video cable and power supply from the LCD box Connect the LCD VGA Video cable to the Video Port Blue on the back of the PC 8 Connect the power cable from the LCD power supply to the connector on the LCD Display Connect the AC cable to the LCD power supply and then to a wall outlet or the optional Power Conditioner Figure 5 Bottom View of LCD and Rear View of PC BOTTOM VIEW OF LCD DISPLAY O
6. ly connected to the keyboard Make sure that the keyboard cable is connected to the keyboard port purple on the logic unit not to the mouse port green The pole display does not have power Make sure it is not plugged into COM port 1 Use COM port 4 Please call UTC RETAIL s Technical Support at 800 349 0546 if you have any problems not addressed in the Troubleshooting Procedures or have questions about other sections of this documentation 2008 UTC RETAIL All rights reserved 11692012 Rev D Page 12 of 12
7. nce when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his her own expense WARNING CMOS Battery Damage Replace your system s CMOS RAM battery only with identical CR 2032 3V Lithium ion coin cell or equivalent battery type to avoid risk of personal injury or physical damage to your equipment Always dispose of used batteries according to the manufacturer s instructions or as required by the local ordinance where applicable Any damage due to not following this warning will void your equipment warranty All access to internal components is restricted to Authorized Service personnel only If applicable the key for this device should be in the possession of Qualified Service Personnel Only and used for access by an Authorized and Qualified Service Person 2008 UTC RETAIL All rights reserved 11692012 Rev D Page 2 of 12 Table of Contents 2200 Series POS Bundle System Installation Guide 0ooooooccccccccccccococacananonanonannnnn non nn nono nnnnnnnnns 2 Productor NOM 4 UN DOXINO the SY StS Mii ais 5 a6 Le 9 tdo A A A O 5 Powering On Your 2200 Series POS Bundle
8. oie age POWER CABLE VIDEO CABLE Power Supply E e ea OPTIONAL o ee POWER CONDITIONER WALL OUTLET O 9 Connect the USB connector end of the Barcode Scanner cable to a USB port on the back of the PC Connect the other end into the jack on the barcode scanner handle Figure 6 Rear View of PC USB CABLE O 2008 UTC RETAIL All rights reserved 11692012 Rev D Page 7 of 12 10 Connect the optional MSR Magnetic Stripe Reader to a USB Port For instructions on the MSR bracket installation refer to the install guide included with the MSR bracket assembly Figure 7 Rear View of PC and Back View of LCD Te o f 1 f S 6 uz fdo o 000 11 Connect the optional Payment Terminal Pin Pad or Signature Capture device to a Serial Port on the back of the PC For instructions on the Signature Capture device cable connections refer to the install guide included with the terminal Plug the AC power adapter into a wall outlet or the optional Power Conditioner Figure 8 Rear View of PC and Top View of Pin Pad device SERIAL DB9 CONNE
Download Pdf Manuals
Related Search