U-Line CO29FF User's Manual
Contents
1. Features and specifications are subject to change without notice j KOR E D gt z z ULIN_0130_A Figure 2 IMPORTANT Proper air flow Figure 2 is required for your unit to operate at its highest efficiently A grille located in the base of the unit must not be blocked at any time or your unit will not perform as expected Initial Startup All U Line units are shipped with controls that are preset No initial adjustments are required IMPORTANT U Line recommends the unit be allowed to run overnight prior to loading the refrigerator and or freezer with product On ice maker equipped units it is possible that dirt or scale will dislodge in the water line Always throw away all ice cubes made during the first two to three hours of operation ULIN 0129 A Figure 3 To turn the unit on or off press the rocker switch Figure 3 located below the temperature control dial in the center of the grille 6 CO29FF Origins Series Temperature Control Checking Product Temperature ULIN_0093_A Figure 4 To check the actual product temperature in refrigerator section only insert an accurate thermometer into a plastic non breakable bottle that is partially filled with water Tighten the bottle cap securely Figure 4 Place the bottle in the refrigerator area for 24 hours Refrain from opening the unit during the testing period After 24 hours check the tem2. Figure 9 6 Make sure grille cap is behind grille in slots provided in grille Figure 9 1 before attaching grille to unit and secure but do not overtighten both grille screws Figure 9 2 7 Reinstall the control knob Figure 7 1 8 Reconnect power to the unit Ice Maker Maintenance Inlet Screen Interval Every Twelve Months The solenoid valve inlet screen must be cleaned at least once each year as follows 1 Shut off the water at the main supply valve 2 Pull the unit out to access the back panel 3 Disconnect electrical power to the unit ULIN 0054 A Figure 10 4 Disconnect the hose connector Figure 10 1 from the water solenoid valve Figure 10 2 5 DO NOT remove the inlet screen from the water solenoid valve Use a tooth brush to gently clean any sediment from the inlet screen 6 Re connect the water supply hose connector Figure 10 1 to the water solenoid valve Figure 10 2 Tighten the connector securely 7 Open the water main supply valve and check for leakage at the water hose connection Ensure that the water supply line is not kinked 8 Reconnect power to the unit before re installing 10 CO29FF Origins Series Ice Cube Thickness Adjustment Interval As Required On ice maker equipped models the cube size may be adjusted by changing the amount of water injected into the ice maker assembly as follows ULIN_0273_A Figure 11 1 Remove th
3. Shut off water supply to the unit at the main water source and disconnect the supply line to the unit s water valve A DANGER RISK OF CHILD ENTRAPEMENT Before you throw away your old refrigerator or freezer take off the doors and leave shelves in place so that children may not easily climb inside 3 Remove the cabinet door if equipped and secure all interior shelves to the interior of the cabinet using a heavy duty cloth or package sealing tape y U LINE GCORPORATION 6 Cleaning and Maintenance General Cleaning Exterior Cleaning As Required Black and White Models e Surfaces may be cleaned with a mild detergent and warm water solution Do not use solvent based or abrasive cleaners Use a soft sponge and rinse with clean water Wipe with a soft clean towel to prevent water spotting Interior Cleaning As Required Turn unit off Clean the interior and all removed components using a mild non abrasive detergent and warm water solution applied with a soft sponge or non abrasive cloth Rinse the interior using a soft sponge and clean water e Do not use any solvent based or abrasive cleaners These types of cleaners may transmit taste to the interior products and damage or discolor the interior Maintenance Proper maintenance of your U Line product will ensure efficiency top performance and long life The maintenance intervals listed are based on normal conditions You may want to shorten
4. 11 T UFLINE GC ORPORATION Door Alignment Check and Adjustment IMPORTANT Properly aligned the door s gasket should be firmly in contact with the cabinet all the way around the door no gaps Carefully examine the door s gasket to assure that it is firmly in contact with the cabinet Also make sure the door gasket is not pinched on the hinge side of the door ULIN 0210 A Figure 14 1 Loosen do not remove top Figure 14 and bottom hinge screws 2 Align door squarely with cabinet 3 Make sure gasket is firmly in contact with cabinet all the way around the door no gaps 4 Tighten bottom hinge screws 5 Tighten top hinge screws Door Reversal Depending upon the location of the unit it may be desirable to change the side on which the door is mounted NOTE On built in installations changing the door mounting to the left side may interfere with ice bucket removal To reverse the door mounting perform the following ULIN 0014 A Figure 15 1 Remove the control knob Figure 15 1 by pulling it away from the cabinet Origins Series 2 Remove two grille screws and remove the grille ULIN 0210 A Figure 16 1 Remove top hinge from cabinet three screws Figure 16 Hold door to keep it from falling 2 Lift the door off the bottom hinge ULIN 0215 A Figure 17 3 Remove bottom hinge from cabinet two screws Figure 17 ULINE 0
5. Origins Series CORPORATION This page intentionally left blank 4 CO29FF Origins Series 3 Safety Precautions IMPORTANT PLEASE READ all instructions completely before attempting to install operate or service your unit Proper installation procedures must be followed if this unit is being initially installed or is moved to a new location after being in service An INSTALLATION GUIDE for your unit providing complete installation information is available from U Line Corporation directly and must be consulted before any installation is begun U Line contact information appears on the rear cover of this guide This unit requires connection to a grounded three prong polarized receptacle that has been placed by a qualified electrician in accordance with applicable electrical codes Safety Alert Definitions Safety items throughout this guide are labeled with a Danger Warning or Caution based on the risk type A DANGER Danger means that failure to follow this safety statement will result in severe personal injury or death NWARNING Warning means that failure to follow this safety statement could result in serious personal injury or death NCAUTION Caution means that failure to follow this safety statement may result in minor or moderate personal injury property or equipment damage General Precautions Use this appliance for its intended purpose only and follow these general precautions
6. Your product may not contain all of the components listed Compressor The compressor makes a hum or pulsing sound that may be heard when it operates e Evaporator Refrigerant flowing through an evaporator may sound like boiling liquid e Condenser Fan Air moving through a condenser may be heard e Automatic Defrost Drain Pan Water may be heard dripping or running into the drain pan when the unit is in the defrost cycle Outdoor Marine and RV Usage Some U Line models are designed to operate in outdoor marine and RV environments For best performance keep the unit out of direct sunlight e If the unit will be shut off for five days or more prop door open to allow for air circulation and prevent mold and mildew IMPORTANT If the ambient temperature is expected to drop below 45 F turn off and unplug unit and drain all water from the unit to prevent freezing damage not covered by the warranty High ambient temperatures 110 F or higher may reduce the unit s ability to reach low temperatures Origins Series Storage Vacation Moving If the unit will not be used for an extended period or otherwise stored follow these steps completely NWARNING Electrical Shock Hazard Disconnect power before servicing Before operating replace all panels Failure to do so may result in death or electrical shock 1 Remove all consumable contents from the unit 2 Disconnect power to the unit 3 Shut off
7. along with those listed throughout this guide A DANGER RISK OF CHILD ENTRAPMENT Before you throw away your old refrigerator or freezer take off the doors and leave shelves in place so that children may not easily climb inside CO29FF U LITIE GCORPORATION NWARNING SHOCK HAZARD Electrical Grounding Required Never attempt to repair or perform maintenance on the unit until the electricity has been disconnected Never remove the round grounding prong from the plug and never use a two prong grounding adapter Altering cutting of power cord removal of power cord removal of power plug or direct wiring can cause serious injury fire and or loss of property and or life and will void the warranty Never use an extension cord to connect power to the unit Always keep your working area dry NCAUTION Use care when moving and handling the unit Use gloves to prevent personal injury from sharp edges If your model requires defrosting DO NOT use any type of heater to defrost Using a heater to speed up defrosting can cause personal injury and damage to the inner lining IMPORTANT Do not lift unit by door handle Never install or operate the unit behind closed doors Be sure front grille is free of obstruction Obstructing free air flow can cause the unit to malfunction and may void the warranty Failure to clean the condenser every three months can cause the unit to malfunction This could void th
8. to call for service If Service is Required If you do not understand a troubleshooting remedy or your product needs service contact U Line Corporation directly Contact information appears on the rear cover of this guide You will be asked for your product Model and Serial Numbers This information should be recorded inside the front cover of this guide following the products original purchase It also appears on the Model and Serial number plate located on the upper right or rear wall of the interior of your product Replacement Parts When you need replacement parts always request that genuine U Line replacements be used U Line products have been designed and engineered using components that work efficiently and provide superior service life and performance The use of aftermarket parts or components may affect the safety operation performance or durability of your product and may also void its warranty 14 CO29FF Origins Series Troubleshooting Guide A DANGER ELECTROCUTION HAZARD Never attempt to repair or perform maintenance on the unit until the main electrical power has been disconnected Troubleshooting What to check when problems occur y U LINE GCORPORATION PROBLEM POSSIBLE CAUSE REMEDY Unit not cold enough Door gasket not sealing properly Adjust door See MAINTENANCE DOOR ALIGN ADJUST REVERSE Item s interfering with door Reposition or remove item s Dirty c
9. 13 Replace three plastic plugs removed in Step 10 into holes on top of unit Replace screws in holes in bottom of unit opposite side 14 Re inspect door seal and alignment Adjust if needed ULIN 0214 A Figure 24 13 y U LINE GC ORPORATION 15 Make sure grille cap is behind grille in slots provided in grille Figure 24 1 before attaching grille to unit and secure but do not overtighten both grille screws Figure 24 2 16 Install the temperature control knob Glass Shelf Removal Installation Remove the shelves as follows ULINE 0277 A Figure 25 1 Open door completely 2 Grasp the shelf edge in the center Figure 25 1 and slide the shelf from the unit 3 Reposition the shelf as required ensuring the raised white edge strip is toward the rear of the unit and the decorative graphics if applied are on the underside of the shelves IMPORTANT Origins Series 7 Service Make sure the shelves are inserted fully into the unit Before Calling for Service If your U Line product appears to be malfunctioning read through the OPERATION section of this guide to ensure that the function of all controls are clearly understood If the malfunction persists the TROUBLESHOOTING GUIDE in this guide will assist you in quickly identifying common problems and provide information on possible causes and remedies Most often this will resolve the problem without the need
10. 216 A Figure 18 4 Remove screws on opposite side of cabinet Figure 18 Note that there may be a nut behind one or both screws on either side 12 CO29FF 5 ULINE_0217_A Figure 19 Install hinge on opposite side bottom of cabinet Figure 19 Replace nut on back side where installed Align hinge outer edge with cabinet before tightening screws ULIN_0109_A Figure 20 Relocate plastic spacer bushing Figure 20 1 on bottom of door to opposite side and place door on bottom hinge pin Clean out bushing hole in door bottom with a screwdriver if needed Plastic Plastic Plug Hole Plug Hole Right Side Left Side Door Swing Door Swing Right Side Invert Invert Hinge Screw Hinge ULIN 0142 A Figure 21 Remove plastic hole plug from door handle and relocate on opposite side Figure 21 Remove pivot screw from top hinge invert screw and reinstall pivot screw in top hinge Figure 21 CO29FF y U LINE GCORPORATION ULIN 0144 A Figure 22 9 Remove three plastic screw plugs in hinge holes top of cabinet opposite side being careful not to scratch cabinet Figure 22 10 Place door on lower hinge pin Invert and install upper hinge on door ULIN 0145 A Figure 23 11 Fasten upper hinge to unit three screws Figure 23 Partially tighten screws until door is aligned 12 Adjust door to assure proper seal Tighten upper hinge screws securely
11. Dealer Address Purchase Date Dealer Telephone 2 CO29FF y U LINE GCORPORATION ins Series 2 Table of Contents LEE O CAUCE OM Me STEEL 2 Warranty REGIStratlOn TT 2 Please Record Your Model Information Table of Contents Safety Precautions Safety Alert Definitions General Precautions Product Features essen Origins Ice Maker Refrigerator Model CO29FF sss eje enale a e E EET 6 IINTEEIESCTei occ 6 Temperature Control sess nnne nene nnen nnne nnne nnrn nnne 7 IAE 7 Normal Operating Sounds sesssssesseseeeseeeee enne nnnennrnn neret en nnne terrere nennen 8 Outdoor Marine and RV Usage n ceci ace rare ea a RES Yea u adds 8 Storage Vacation MOVING cesecccceeeeeneeeeeeeeeeeneeeeeeeeeneeeeeeeaaaeeeeeseeeaaaeeeeeescaeeeeeeesenaeeeees 8 Prod ct DISDOSAll be E Cleaning and Maintenance General Cleaning MailniteriariCe icone t rit asap A RE ERR RD TR ERR ERKR SERERE NE ETE E XEXRES RAF a sara EIL Before Calling for Service If Service is Required Replacement Parts iacere HR eorr ir E ce a ee va ve DERE CHER db Lgs aa Troubleshooting Guide ssesssesessseeseseeeeeeen neret nre U Line Corporation Limited Warranty CO29FF 3 py U rrmE
12. Line Corporation Limited Warranty is located on the inside rear cover of this guide To validate your warranty the product and its original purchase date must be registered A Warranty Registration Card has been included for this purpose in the package containing this manual Complete and mail the Warranty Registration Card or register your product online at www U LineService com as soon as possible after purchase If your product registration is not on file and a request for warranty coverage is received the date of sale to the U Line Selling Dealer or Distributor will be established as the first date of warranty coverage for your product Please Record Your Model Information When you request additional information or service you will be asked for your products model and serial numbers You can find this information on the serial plate located on the upper right or rear wall in the interior of your unit This information also appears on the warranty registration card OR RET LISTED amp 4R U LINE 85S j DA me UL MILWAUKEE WISCONSIN USA HIGH SIDE DESIGN PRESSURE 300 PSI LOW SIDE DESIGN PRESSURE 140 PSI Model Serial No X XXXXXX XX 04 XXXX 05 XXXX X XHP 60 HZ 1 PHASE X XA R134A X XXOZ ULIN_0023_A Figure 1 Please record the model number Figure 1 1 serial number Figure 1 2 date of purchase and dealer contact information for your U Line product below Model Number Dealer Name Serial Number
13. Origins Series Use and Care Guide Combo Model CO29FF CO29FF J UsLINE oe CORPORATION tigins Series 1 Introduction Congratulations on your purchase of a U Line refrigeration product A pioneer in the field for more than 40 years U Line Corporation is the world s number one manufacturer of built in under counter specialty refrigeration and ice making products U Line dedicates 100 of its research and development to these products The result U Line technology consistently leads the market with innovation design depth of product line and performance U Line products are making life more convenient in homes businesses and hotels around the world U Line supports its products with a strong dealer network and its commitment to quality even extends to environmentally safe packaging IMPORTANT READ all of the instructions in this guide completely before operating the unit for the first time For future reference keep this guide in a safe accessible location If you need additional information or assistance please contact U Line Corporation directly Contact information appears on the rear cover of this guide If you have a problem with the operation of this product the SERVICE section of this guide will assist you in quickly identifying common problems and provide information on possible causes and remedies If your product needs service contact U Line directly Warranty Registration Your U
14. U Line shall 1 repair or replace any part of the sealed system that breaches this warranty and 2 for all Marine RV and Domestic U Line products sold and serviced in the United States including Alaska and Hawaii and Canada U Line shall cover the labor costs incurred in connection with the replacement of any defective part of the sealed system All other charges including transportation charges for replacements under this warranty and labor costs not specifically covered by this warranty shall be borne by you This warranty is extended only to the original purchaser of the U Line product The Registration Card included with the product should be promptly completed by you and mailed back to U Line or you can register on line at www U LineService com The following are excluded from this limited warranty installation charges damages caused by disasters or acts of God such as fire floods wind and lightening damages incurred or resulting from shipping improper installation unauthorized modification or misuse abuse of the product customer education calls food loss spoilage door and water level adjustments except during the first 90 days from the date of purchase defrosting the product adjusting the controls door reversal or cleaning the condenser If a product defect is discovered during the applicable warranty period you must promptly notify either the dealer from whom you purchased the product or U Line at P O Box 245040 Milwauke
15. cket NWARNING NEVER use an ice pick knife or other sharp instrument to separate cubes Shake the ice bucket instead During periods of limited usage or high ambient temperatures it is common for cubes to fuse together Shake the bucket to break apart cubes If the ice maker is not used regularly the ice bucket should be emptied periodically to ensure fresh cubes It is normal for cubes to appear cloudy This is caused by air being trapped in the water due to fast freezing It has nothing to do with the health taste or chemical make up of the water It is the same air that is in every glass of water you drink CO29FF 7 T UFLINE CORPORATION The ice bucket can be removed for emptying and cleaning To remove the ice bucket raise the bin arm and remove the bucket from the ice compartment Use the ice bucket for ice storage only Normal Operating Sounds All models incorporate rigid foam insulated cabinets to provide high thermal efficiency and maximum sound reduction for its internal working components In spite of this technology your model may make sounds that are unfamiliar Normal operating sounds may be more noticeable because of the unit s environment Hard surfaces such as cabinets wood vinyl tiled floors and paneled walls have a tendency to reflect normal appliance operating noises Common refrigeration components and a brief description of the normal operating sounds they make are listed below NOTE
16. e Wisconsin 53224 or at 414 354 0300 In no event shall such notification be received later than 30 days after the expiration of the applicable warranty period U Line may require that defective parts be returned at your expense to U Lines factory in Milwaukee Wisconsin for inspection Any action by you for breach of warranty must be commenced within one year after the expiration of the applicable warranty period This limited warranty is in lieu of any other warranty express or implied including but not limited to any implied warranty of merchantability or fitness for a particular purpose provided however that to the extent required by law implied warranties are included but do not extend beyond the duration of the express warranty first set forth above U Lines sole liability and your exclusive remedy under this warranty is set forth in the initial paragraph above U Line shall have no liability whatsoever for any incidental consequential or special damages arising from the sale use or installation of the product or from any other cause whatsoever whether based on warranty express or implied or otherwise based on contract tort or any other theory of liability Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages so the above limitations may not apply to you This warranty gives you specific legal rights and you may also have other rights which va
17. e ice maker assembly cover Figure 11 ULIN 0056 A Figure 12 2 Locate the adjusting screw on the ice maker assembly control box The adjusting screw is just below the minus and plus signs on the control box Figure 12 NOTE Make adjustments in small increments Too large of an adjustment could cause the unit to malfunction NCAUTION Too large of an adjustment to the screw can cause the water to overflow the ice maker and can cause property damage 3 Turn the adjusting screw toward the minus sign clockwise for smaller cubes or toward the plus sign counterclockwise for larger cubes y U LINE GCORPORATION 4 Install the ice maker assembly cover IMPORTANT Use only genuine U Line replacement parts U Line ice maker parts are not the same as standard FSP Whirlpool parts Using non U Line parts can reduce ice rate cause water to overflow from ice maker mold damage the unit and may void the warranty Leveling It is important that this unit is set level for proper door and ice maker operation t CLOSER ULIN 0211 A Figure 13 Use a level to check the levelness of the unit from front to back and from side to side Level should be placed along top edge and side edge as shown Figure 13 NOTE This model DOES NOT have leveling feet This model MUST be placed on a level surface to operate properly CO29FF
18. e warranty Allow unit temperature to stabilize for 24 hours before use If your model requires defrosting never use an ice pick or other sharp instrument to help speed up defrosting These instruments can puncture the inner lining or damage the cooling unit Use only genuine U Line replacement parts Imitation parts can damage the unit affect its operation or performance and may void the warranty y U LINE CcCORPORATION 4 Product Features Origins Series 5 Operation Origins Ice Maker Refrigerator Model CO29FF The CO29FF Ice Maker Refrigerator with adjustable temperature control provides 2 1 cubic feet 59 L of refrigeration in one compact unit e The ice maker produces up to 8 Ibs 3 6 kg of ice per day and will store 13 lbs 5 9 kg It conserves on water using only 2 3 4 gallons 12 5 L to produce approximately 22 Ibs 10 kg of ice Frost Free technology Two tempered glass shelves provide a generous amount of shelving space The shelves are easy to clean e Two in door shelves feature clear bottle retainers and an additional half shelf is provided to maximize storage capacity The door features an integrated handle and can accommodate a custom 1 4 0 64 cm flat or raised panel to match surrounding cabinets e The door is field reversible e The unit features a vinyl clad steel cabinet that provides a rich textured look and resists scratching peeling and flaking
19. ld Be sure freezer door is closed correctly Unit too cold Temperature control set too cold Set control to warmer setting See OPERATION CO29FF 15 py U rrmE Origins Series CORPORATION This page intentionally left blank 16 CO29FF Origins Series y U LINE GCORPORATION This page intentionally left blank CO29FF 17 py U rrmE Origins Series CORPORATION This page intentionally left blank 18 CO29FF y U LINE GCORPORATION Origins Series U Line Corporation Limited Warranty U Line Corporation warrants each U Line product to be free from defects in materials and workmanship for a period of one year from the date of purchase and warrants the sealed system consisting of the compressor the condenser the evaporator the hot gas bypass valve the dryer and the connecting tubing in each U Line product to be free from defects in materials and workmanship for a period of five years from the date of purchase During the initial one year warranty period for all U Line products U Line shall 1 at U Lines option repair any product or replace any part of a product that breaches this warranty and 2 for all Marine RV and Domestic U Line products sold and serviced in the United States including Alaska and Hawaii and Canada U Line shall cover the labor costs incurred in connection with the replacement of any defective part During years two through five of the warranty period for the sealed system
20. ondenser coils Clean condenser See MAINTENANCE CONDENSER CLEANING Airflow to front grille blocked Airflow must not be obstructed to front grille See OPERATION Temperature not set cold enough Set control knob to cooler setting See OPERATION Allow 24 hours for temperature to stabilize Water is leaking out the back of the Water supply connection leaking unit Tighten fitting as required Ice cubes sticking together Door gasket not sealing properly Adjust door See MAINTENANCE DOOR ALIGN ADJUST REVERSE Infrequent use of cubes Break apart cubes Noise during operation Copper water supply tubing contacting internal components Carefully bend tubing away from cabinet and components Certain sounds are normal Not enough ice Ice cube size too large No ice Bin arm locked in upright position Lower bin arm No water to unit Soft sounds from the fan and water dropping sounds from the ice maker will be heard Turn on water or contact plumber Set cube size smaller See MAINTENANCE ICE MAKER ICE CUBE THICKNESS ADJUST Dirty condenser coils Clean condenser See MAINTENANCE CONDENSER CLEANING Freezer door not closed correctly Water leaks into ice bucket Water level set too high Set cube size smaller See MAINTENANCE ICE MAKER ICE CUBE THICKNESS ADJUST Fresh food section on Combo units Ice bucket not fully inserted Push ice bucket into place too co
21. perature of the water If required adjust the temperature control in a small increment See ADJUSTING TEMPERATURE Factors which affect the internal temperatures of the cabinet include Temperature setting Ambient temperature where installed Number of times and length of time the door is opened and closed Installation in direct sunlight or near a heat source Adjusting Temperature ULIN 0014 A Figure 5 Adjust the temperature by turning the numbered dial Figure 5 1 in small increments y U LINE GCORPORATION Ice Maker When the ice bucket is full the ice making mechanism will shut off However the refrigeration system will continue to cool and maintain the cube supply Frost free icemaker units have lower ice production than manual defrost units IMPORTANT Do not place cans or bottles in the ice compartment because they will freeze ULIN 0087 A Figure 6 Ice production may be interrupted by raising the bin arm into an upright and locked position Figure 6 The unit will maintain temperature for ice storage IMPORTANT If you are not intending to use the ice maker and turn the supply valve off it is imperative to raise the bin arm of the ice maker Figure 6 Failure to raise the bin arm may result in damage to the water valve Certain sounds are normal during the unit s operation You may hear the compressor or fan motor the water valve or ice dropping into the ice bu
22. ry from state to state CO29FF 19 UR U LINE CORPORATION For General Inquiries P O Box 245040 O S Milwaukee Wisconsin r l g 1 n S e r 1 e S 53224 9540 U S A Phone 800 779 2547 FAX 414 354 5696 www U Line com For Service and Parts Assistance Phone 800 779 2547 414 354 0300 FAX 414 354 5696 Email OnLineService U Line com www U LineService com E mail OnlineParts u line com For more than four decades U Line has distinguished itself as the leader in built in under counter ice making refrigeration and wine storage appliances An INSTALLATION MANUAL for your unit providing complete installation information is available for download at www U Line com Information for custom panel inserts per model including panel size and instructions are available by visiting www U Line com When you need replacement parts always request genuine U Line replacements be used Visit www U Line com to locate a parts distributor in your area Echelon Serves Origins Series U Line Corporation located in Milwaukee WI is a family operated manufacturer of built in undercounter ice makers Combo ice maker refrigerators Wine Captain wine storage units refrigerators refrigerated drawers and refrigerator freezers 2006 U Line Corporation Publication No 30099 01 2006 Rev A
23. the intervals if you have pets or other special considerations Defrosting Frost Free Models Frost free models do not produce frost in normal operating conditions WARNING DO NOT use any type of electrical heating device ice pick knife or other sharp instrument to defrost this could damage the inner lining or refrigeration system and void the warranty CO29FF 9 y U LINE CORPORATION Condenser Cleaning Interval Every Three Months To maintain operational efficiency keep the front grille free of dust and lint and clean the condenser every three months Depending on environmental conditions more or less frequent cleaning may be necessary NWARNING Disconnect electric power to the unit before cleaning the condenser NWARNING DO NOT touch the condenser fins The condenser fins are SHARP and can be easily damaged IMPORTANT DO NOT use any type of cleaner on the condenser unit 1 Disconnect power to the unit ULIN 0197 A Figure 7 2 Remove the control knob Figure 7 1 by pulling it straight out away from grille 3 Remove two screws from grille Figure 7 2 and save 4 Remove grille and grille cap from unit ULIN 0153 A Figure 8 5 Clean the condenser coil Figure 8 1 using a using a soft brush with a combing action or vacuum cleaner Do not touch the condenser coil ULIN 0198 A
24. water supply to the unit at the main water source IMPORTANT If the ambient temperature is expected to drop below 45 F turn off and unplug unit and drain all water from the unit to prevent freezing damage not covered by the warranty The use of anti freeze or other products of this nature is not necessary and is not recommended 4 Disconnect the water valve inlet and outlet lines and allow them to drain completely 5 Reconnect power to the unit and allow it to run for one hour minimum until any remaining ice has been ejected from the ice maker assembly 6 Disconnect power to the unit dry any remaining water from the ice maker assembly and reconnect any lines removed from the water supply valve 7 Disconnect the power cord from its outlet and leave it disconnected until the unit is returned to service 8 Clean and dry the interior of the cabinet See CLEANING AND MAINTENANCE GENERAL CLEANING 9 During periods of non use the cabinet must remain open to prevent the formation of mold and mildew Open door a minimum of 2 5 cm to provide the necessary ventilation 8 CO29FF Origins Series Product Disposal If the unit is being removed from service for disposal check and obey all Federal State and or Local regulations regarding the disposal and recycling of refrigeration appliances and follow these steps completely 1 Disconnect power to the unit and unplug the power cord from its outlet 2
Download Pdf Manuals
Related Search