Tripp Lite 12U User's Manual
Contents
1. 3 Feature Identification Ei Rear Door A Front Door E Horizontal Rails EY Vertical Mounting Rails El Removeable Cable Access Hole Covers A Vents Locking Removeable Side Panels 4 Enclosure Installation Caution Read All Instructions and Warnings Before Installation Warning Rack enclosures can be extremely heavy Do not attempt to unpack move or install the enclosure without assistance Use extreme caution when handling the enclosure and be sure to follow all handling and installation instructions Do not attempt to install equipment without first stabilizing the enclosure 4 1 Preparation The enclosure must be installed in a structually sound area that is able to bear the weight of the enclosure all the equipment that will be installed in the enclosure and any other enclosures and or equipment that will be installed nearby Before unpacking the enclosure you should transport the shipping container closer to the final installation location to minimize the distance you will need to move the unit after the protective packaging has been removed If you plan to store the enclosure for an extended period before installation follow the instructions in the Storage and Service section You need several tools You also need the following hardware e Level e Appropriate hardware for wall mounting not included e Phillips head Screwdriver e Appropriate tools for wall mounting 4 2 Unpacking Use at least two people to unpac2. and installed equipment must not exceed the load capacity of the pallet Tripp Lite is not responsible for any damage that occurs during reshipment e Use of this equipment in life support applications where failure of this equipment can reasonably be expected to cause the failure of the life support equipment or to significantly affect its safety or effectiveness is not recommended Do not use this equipment in the presence of a flammable anesthetic mixture with air oxygen or nitrous oxide If installing optional casters SRCASTER see page 7 for caster installation e The casters are not designed to provide long term support for the enclosure after final installation The casters are designed for minor position adjustments within the final installation area only The casters are not designed for moving the enclosure over longer distances e Do not push the enclosure from the side panels to move it Pushing from the side panels will cause a tipping hazard e When rolling the enclosure on its casters always push it from behind never pull it toward you e A rolling enclosure can cause personal injury and property damage if not properly supervised If rolling the enclosure down a ramp is required use extreme caution Do not attempt to use ramps that have a slope steeper than 1 12 2 Overview SmartRack Enclosures accommodate all standard 19 inch rackmount equipment regardless of vendor and ship fully assembled for quick and easy deployment
3. each rack unit are numbered and also include a small notch to aid identification A single rack unit includes the space occupied by the numbered hole and the holes directly above and below 1 Rack Unit 7 1 Installing or Removing Cage Nuts WARNING The flanges of the cage nuts should engage the sides of the square opening in the rail not the top and bottom Follow the instructions in your equipment documentation to ensure proper installation of your equipment El Locate the numbered square openings in the mounting rails where you plan to install your equipment You will install cage nuts included into the square openings in order to provide an attachment point for the mounting screws included Note Consult your equipment documentation to determine how many cage nuts will be required and where they will need to be installed 1 El From the inside of the mounting rail insert one of the flanges of the cage nut through the square opening Press it against the side of the square opening Each flange should engage one side of the Square opening not the top or bottom DI Qe 2 E E Compress the cage nut at the sides slightly to allow the remaining flange to fit through the square C opening When the cage nut is properly installed both flanges will protrude through the square opening and will be visible on the outer surface of the mounting rail Repeat steps 1 3 until all Bll required cage nuts are installed By i 3 El After insta
4. All parts of the enclosure are grounded to the frame of the enclosure Use the enclosure s front or rear threaded grounding point EY and an M6 screw included to connect the frame of the enclosure directly to your facility s earth ground connection with an 8 AWG 3 264 mm wire Route the ground wire under the enclosure s frame to ensure unhindered door operation Warning Attach each enclosure to earth ground separately Do not use the enclosure without an earth ground connection QO Na EARTH GROUND 5 Enclosure Configuration Before installation be sure to plan the location and arrangement of components within the enclosure Be sure all mounting rails are reversed or adjusted for depth depending on your equipment configuration 5 1 Door Locks All enclosure doors including front and back doors as well as both side panels have locks that are accessible by included keys 5 2 Cable Access and Management The back door of the enclosure has a square opening for cable access and management An additonal opening can be found on top of the main cabinet Each opening can also be closed by screwing in the removeable cable access panels 5 3 Reversing the Enclosure In order to accommodate various rack configurations the enclosure can be reversed To do so simply turn the enclosure over so that the doors open in the opposite direction 5 Enclosure Configuration continued 5 4 Mounting Rails The enclo
5. Owner s Manual oe 12U Wall Mounted SmartRack Enclosure Model SRW12US R RoHS COMPLIANT Table of Contents N e gt 1 Important Safety Instructions 6 Wall Mounting the Enclosure 2 Overview 9 6 1 Mounting 6 3 Feature Identification 3 g 7 Equipment Installation L 4 Enclosure Installation 4 7 1 Installing or Removing Cage Nuts 7 4 1 Preparation 4 8 Optional Casters 7 4 3 Placement 4 10 Storage and Service 8 Slane connec toe 3 11 Warranty amp Warranty Registration 8 Francais 9 5 1 Door Locks 5 2 Cable Access amp Management 5 3 Reversing the Enclosure 5 4 Mounting Rails 5 5 5 6 6 5 5 Adjusting Mounting Rail Depth TRIPP LITE Tripp Lite World Headquarters 1111 W 35th Street Chicago IL 60609 USA 773 869 1234 e www tripplite com Copyright 2009 Tripp Lite All trademarks are the sole property of their respective owners 1 Important Safety Instructions SAVE THESE INSTRUCTIONS This Manual contains instructions and warnings that must be followed during the installation and operation of the product described in this manual Failure to comply may invalidate the warranty and cause property damage or personal injury e Keep the enclosure in a controlled indoor environment away from moisture temperature extremes flammable liquids and gasses conductive contaminants dust and direct sunlight e Leave adequate space at the front and rear of the enclosure for pr
6. k the enclosure Move shipping pallet to a firm level surface Open box and remove the four foam cormer protectors Save all packing materials for later use unless you are certain they will not be required Packing materials are recyclable With one person on each side carefully lift the enclosure out of the box and place on a firm level surface Examine the enclosure for any damage or loose parts Confirm all parts are present If anything is missing or damaged contact Tripp Lite for assistance Do not attempt to use the enclosure if it has been damaged Never extend more than one component from the enclosure at a time 4 3 Placement If using the optional casters you can use the casters to move the enclosure for a short distance over a level smooth stable surface by pushing it from the front or rear not the side panels Do not attempt to roll the enclosure over long distances The enclosure should be moved close to its installation location inside its shipping container before it is unpacked Warning Do not push or pull the enclosure at the side panels or pull the enclosure toward you Only experienced equipment operators should attempt to lift the enclosure Use appropriate equipment and follow all applicable safety procedures and regulations Warning Never attempt to lift or install without adequate help Do not try lifting the enclosure alone 4 Enclosure Installation continued 4 4 Ground Connection
7. lling the required cage nuts use the included mounting screws and cup washers to secure g q g g p your equipment to the rack rail Place the cup washers between the screws and the equipment mounting brackets Note Your equipment may also include mounting hardware Read the mounting instructions that came with your equipment before installing your equipment To Remove Cage Nuts Reverse Steps 1 3 Note You may wish to use a cage nut tool user supplied to aid cage nut installation and removal 8 Optional Casters An optional caster accessory kit Model SRCASTER is available separately through Tripp Lite Go to www tripplite com or call 773 869 1234 for details The SRCASTER Kit consists of 4 casters with required locknuts and bolts for installation The casters install to the base of the unit using pre drilled holes as shown in the illustration below For further installation instructions refer to the manual included with the SRCASTER Kit 9 Specifications 25 x 23 63 x 21 6 635 x 600 x 549 mm 200 Ib 90 kg Stationary 200 Ib 90 kg Rolling Adjustable from 3 to 20 5 76 to 521 mm Full wall mount load capacity requires a mounting surface capable of bearing the full load Rolling applications require optional SRCASTER accessory kit 10 Storage and Service Storage The enclosure should be stored in a controlled indoor environment away from moisture temperature extremes flammable liquids and gasses co
8. nductive contaminants dust and direct sunlight Store the enclosure in its original shipping container if possible Service The enclosure is covered by the limited warranty described in this manual For more information call Tripp Lite Customer Service at 773 869 1234 11 Warranty and Warranty Registration 5 Year Limited Warranty Seller warrants this product if used in accordance with all applicable instructions to be free from original defects in material and workmanship for a period of 5 years from the date of initial purchase If the product should prove defective in material or workmanship within that period Seller will repair or replace the product at its sole discretion THIS WARRANTY DOES NOT APPLY TO NORMAL WEAR OR TO DAMAGE RESULTING FROM ACCIDENT MISUSE ABUSE OR NEGLECT SELLER MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY EXPRESSLY SET FORTH HEREIN EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW ALL IMPLIED WARRANTIES INCLUDING ALL WARRANTIES OF MERCHANTABILITY OR FITNESS ARE LIMITED IN DURATION TO THE WARRANTY PERIOD SET FORTH ABOVE AND THIS WARRANTY EXPRESSLY EXCLUDES ALL INCIDENTAL AND CONSEQUENTIAL DAMAGES Some states do not allow limitations on how long an implied warranty lasts and some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitations or exclusions may not apply to you This warranty gives you specific legal rights and you may have other righ
9. oper ventilation Do not block cover or insert objects into the external ventilation openings of the enclosure e The enclosure is extremely heavy Use caution when handling the enclosure Do not attempt to unpack move or install it unassisted Use a mechanical device such as a forklift or pallet jack to move the enclosure in the shipping container e Do not place any object on the enclosure especially containers of liquid and do not attempt to stack the enclosures e Inspect the shipping container and the enclosure for shipping damage Do not use the enclosure if it is damaged e Leave the enclosure in the shipping container until it has been moved as close to the final installation location as possible e Install the enclosure in a structurally sound area capable of handling the load or on a level floor that is able to bear the weight of the enclosure all equipment that will be installed in the enclosure and any other enclosures and or equipment that will be installed nearby e Use caution when cutting packing materials The enclosure could be scratched causing damage not covered by the warranty e Save all packing materials for later use Repacking and shipping the enclosure without the original packing materials may cause product damage that will void the warranty e Do not reship the enclosure with additional equipment unless the enclosure was shipped with a special shock pallet SP1 models only The combined weight of the enclosure
10. sure 6 1 Mounting There are 12 keyhole cutouts on the back door of the enclosure Each keyhole can accommodate an M5 or 3 16 bolt The holes are on centers and beginning with the two innermost holes the centers are 13 3 4 16 and 18 1 4 apart respectively moving outward and horizontaly Holes are then a standard 19 apart vertically as shown in the diagram Using a level measure to position your mounting areas precisely Use appropriate fasteners not included to secure the enclosure to the wall Warning The area you plan to mount the enclosure to must be able to withstand the weight of the enclosure and all mounted equipment For the weight of the enclosure and its capacity see the specifications on page 8 a OO O OO O O 1 18 lt M 16 134 gt t90 000 i 1 6 lt 16 lt _ 16 7 Equipment Installation Warning Do not install equipment until you have stabilized the enclosure Install heavier equipment first and install it towards the bottom of the enclosure Install equipment starting from the bottom of the enclosure and proceeding toward the top of the enclosure never the reverse If using sliding equipment rails be careful when extending the rails Do not extend more than one set of sliding equipment rails at one time Avoid extending sliding equipment rails near the top of the enclosure Note The square holes in the middle of
11. sure comes with mounting rails that have square holes for mounting rack equipment To install equipment use the included cage nuts and other hardware See page 7 for installation of cage nuts Warning Be sure to have the enclosure securely mounted to the wall or in its final position on the floor before mounting any equipment inside Also be sure to have all the right adjustments on your rails before mounting equipment See below for Adjusting Mounting Rail Depth 5 5 Adjusting Mounting Rail Depth Warning Do not attempt to adjust rails while equipment is installed in the enclosure Do not attempt to use rails without screws installed 2 per rail The 4 mounting rails are pre installed to accommodate equipment with a mounting depth of 20 5 inches 521 mm Do not adjust the mounting rails unless your equipment requires a different mounting depth The front and rear sets of rails can be adjusted independently in 1 4 inch 6mm increments for mounting depths between 3 inches 76 mm and 20 5 inches 521 mm El Each rail is connected to the enclosure with 2 screws 1 in the upper corner and another in the lower corner Using a Phillips head screwdriver remove the screws that fasten the rails to the enclosure El Slide the mounting rails to the desired depth and reattach them using the screws you removed in Step 1 6 Wall Mounting the Enclosure Warning Do not attempt to mount the enclosure to the wall with equipment mounted in the enclo
12. ts which vary from jurisdiction to jurisdiction WARNING The individual user should take care to determine prior to use whether this device is suitable adequate or safe for the use intended Since individual applications are subject to great variation the manufacturer makes no representation or warranty as to the suitability or fitness of these devices for any specific application Warranty Registration Visit Www tripplite com warranty today to register the warranty for your new Tripp Lite product You ll be automatically entered into a drawing for a chance to win a FREE Tripp Lite product No purchase necessary Void where prohibited Some restrictions apply See website for details Tripp Lite has a policy of continuous improvement Specifications are subject to change without notice Made in China TRIPP LITE Tripp Lite World Headquarters 1111 W 35th Street Chicago IL 60609 USA 773 869 1234 www tripplite com Copyright 2009 Tripp Lite All trademarks are the sole property of their respective owners 8 200812110 93 2861 _EN
Download Pdf Manuals
Related Search