Home

Trimble Outdoors LP20 User's Manual

1. 1 Find a room at least 10 m 35 ft long Mark lt a point A on the floor at Steps 1 4 EyA o one end of the room Mark point A Set up laser I l over A l l 2 Set up the laser so that its Mark points I o down beam is over point A ake BY Make sure the level beam Dy _ 0 points toward the far end Steps 5 6 l of the room Set up laser I over B I l Align to point C l 3 Mark a point B on the Mark point D l floor at the center of the room using a target Steps 7 8 l to transfer the level beam laser 90 location to the floor and align to D cy Mark point E 4 Mark a point C on the far wall or transfer the level beam location to the floor a pa Laser Safety The pocket laser uses a Class 2 laser which complies with the requirements based on the IEC825 1 EN60825 standards Class 2 based on 21CFR 1041 This laser may be operated without the need for any additional protective measures Nevertheless as with the sun care should be taken to avoid looking directly into the light source CAUTION Never look directly into the laser beam Please keep the pocket laser out of the reach of children Wp LASER LIGHT DO NOT STARE INTO BEAM CLASS 2 LASER PRODUCT PER 21 4 Rotate the laser 180 and realign the down beam over the reference mark on the floor 5 Locate the position of the DZ up beam on the ceiling which will be twice the actual
2. 3 Close the battery door and latch it shut Dayton Ohio 45424 1099 U S A 2 Power Status LED 5 Plumb Offset Mark y Phone 937 245 5600 800 538 7800 3 Lens 6 Battery Housing FAX 937 233 9004 Ne Internet www trimble com www trimble com Trimble Oe A Setting Up the Laser and Transferring a Point 0002 8210 Universal Accessory are ae Setups attempted through glass or other material will affect the 3 Adjust the position of the CME EU Marke meN Tinea a 20 SEUNS nae eal sa accuracy of the laser laser so that the down beam aan is on the control point NI io 72 mm 23 16 in me 4 Locate the position of the A up beam and level beam Make a mark on the ceiling and wall respectively Ceiling with 0002 1106 Pipes Conduit Ceiling Mount 1 Press the power button The green power status LED lights to show that the laser is on CAUTION Never look directly into the laser beam 2 Place the laser on a flat surface The laser must be within 4 of being level for it to self level O 6 Plumbing a Wall Specifications Maintenance and Care System Cleaning 6 mm 21 m 1 4 in 70 fi 1 Place the laser so that the inaen nOA You will get years of service from your laser by following the For maximum performance and accuracy always keep the lenses bottom feet are on the front manene and Sate recommendations mah
3. Introduction Features Installing Removing the Batteries CAUTION The batteries should be removed when storing the laser more than 30 days Thank you for choosing the LP20 or LP40 Spectra Precision LP20 LP40 Laser Pointer Laser from the Trimble family of precision hand held lasers This User Guide simple to use tool allows you to transfer points between the floor and ceiling and to establish 90 points for laying out wall lines and putting up wall partitions You can also use the laser for other applications where true plumb square and level setups are required Before using the laser be sure to read this operator s manual carefully Included in it is information about setting up using and maintaining the laser Also included in this manual are CAUTIONS and Notes Each of these words represents a level or danger or concern A CAUTION indicates a hazard or unsafe 1 Release the battery door using your fingers Open the door practice that could result in minor injury or property damage SPECTRA A Note indicates important information unrelated to safety LASER Your comments and suggestions are welcome please contact us at 2 Install remove the 4 AA batteries Note When installing the batteries be sure to note the positive i Pone Bien A Level Ofna Mark and negative diagrams molded on the battery housing Trimble Construction Division 5475 Kellenburger Road
4. Locate the position of the level beam on the wall and make a mark 6 Move the laser to the far wall facing the wall Request for Service Our goal is to provide prompt and efficient service through competent service dealers To locate your local dealer or authorized Trimble Service Center contact our world centers listed below North America Africa amp Middle East Trimble Construction Division Trimble Export Middle East 5475 Kellenburger Road P O Box 17760 Dayton Ohio 45424 1099 Jebel Ali Free Zone Dubai U S A UAE 800 538 7800 Toll Free 97 1 4 881 3005 Phone 1 937 245 5600 Phone 97 1 4 881 3007 Fax 1 937 233 9004 Fax i Asia Pacific Europe Trimble Navigation Trimble GmbH Australia PTY Limited Am Prime Parc 11 Level 1 120 Wickham Street 65479 Raunheim Fortitude Valley QLD 4006 GERMANY AUSTRALIA 49 6142 2100 0 Phone 49 6142 2100 550 Fax 61 7 3216 0044 Phone 61 7 3216 0088 Fax Latin America China Trimble Navigation Limited Trimble Beijing 6505 Blue Lagoon Drive Room 2805 07 Tengda Plaza Suite 120 No 168 Xiwai Street Miami FL 33126 Haidian District U S A Beijing China 100044 1 305 263 9033 Phone 1 305 263 8975 Fax 86 10 8857 7575 Phone 86 10 8857 7161 Fax www trimble com cn 19 Any evidence of negligent abnormal use accident or any attempt to repair equipment by other than factory authorized personnel Trimble certified or recommended parts automatically voids the warra
5. ate or mail a request for recycling instructions to Trimble Europe BV c o Menlo Worldwide Logistics Meerheide 45 5521 DZ Eersel NL 20 Trimble Trimble Construction Division 5475 Kellenburger Road Dayton Ohio 45424 1099 U S A 1 937 245 5600 Phone www trimble com CEO nox 2004 2005 Trimble Navigation Limited All rights reserved Reorder PN 0002 0020 Rev D 10 05
6. error and make a mark 6 Measure the difference between the two marks on the ceiling which will be twice the actual error If the difference is more than _ lt 5 mm in 7 5 m 3 16 in in 25 ft the laser must be serviced at an authorized Difference service center gt 5 mm gt 3 16 in 14 5 Move the LP40 to point B and align the level beam to point C again 6 Mark the location of the square beam D on the floor Note To ensure accuracy the distances from A to B B to C and B to D should be equal 7 Turn the LP40 90 so that the level beam aligns with point D 8 Mark the location of the square beam E on the floor as close as possible to point A 9 Measure the distance between points A and E If the measurement is greater than the values shown below the laser must be serviced at an authorized service center Room length or distance The 90 angle between the between points Aand C level beam and square beam is out of calibration if the distance between points A and E is 10 m 35 ft gt 9 0 mm 3 8 in 20 m 70 ft gt 18 0 mm 3 4 in 15 Warranty Trimble warrants the Spectra Precision Laser LP20 and LP40 to be free of defects in material and workmanship for one year This warranty period is in effect from the date the system is delivered by Trimble or its authorized Dealer to the purchaser or is put into service by a Dealer as a demonstrat
7. i manal However clean When cleaning apply very light pressure and use only a edge of the bottom track 6 mm 30 m 14 in 100 fi well the product is designed mishaps do occur and the most good quality glass cleaner on a soft cloth to clean the exterior of Square Beam Accuracy LP40_ 6 mm 30 m x 14 in 100 fi common problems associated with these are covered in the the laser and its lenses Self Leveling Range 4 from level following areas Any damage to the laser caused by improper Out of Level Indicator maintenance and care voids the warranty CAUTION A dry cloth or abrasive organic cleaner could scratch Working Range 20 30 m 65 100 ft or damage these surfaces 2 Press the power button Y Leer as Handling Precautions Laser Type LP40 635 nm LP20 650 nm CAUTION Do not submerge the laser 3 Adjust the top of the 4 When transferring the laser from a very low temperature to a pth ian Shap hop partition until the up 7 warmer environment or visa versa always allow time for the laser Storage beam is on the front edge l Battery Type to reach the new temperature before using Allowing this time is H 3 7 3 of the top track F Battery Life 40 hours alkaline especially important when transferring the laser from an extremely When youre not using the laser store it in its pouch carrying case Low Battery Indicator LED Blinking heated cold vehicle to the job site Auto Shutof
8. nty Special precautions have been taken to ensure the calibration of the laser however calibration is not covered by this warranty Maintenance of the calibration is the responsibility of the user The foregoing states the entire liability of Trimble regarding the purchase and use of its equipment Trimble will not be held responsible for any consequential loss or damage of any kind This warranty is in lieu of all other warranties except as set forth above including an implied warranty merchantability of fitness for a particular purpose is hereby disclaimed This warranty is in lieu of all other warranties expressed or implied 23 7 Adjust the lasers height until the beam is superimposed over the mark made in step 5 8 Without changing the height of the laser rotate it 180 to place the beam near the mark on the first wall step 3 9 Measure the vertical distance between the beam and the mark made in step 3 If the measurement is greater than the values shown below the laser must be serviced at an authorized service center 6 m 20 ft 3 0 mm 1 8 in 12 m 40 ft 6 0 mm 1 4 in 18 m 60 ft 8 0 mm 5 16 in 24 m 80 ft 11 0 mm 7 16 in 16 Notice to Our European Union Customers For product recycling instructions and more information please go to www trimble com environment summary html Recycling in Europe To recycle Trimble WEEE call 31 497 53 2430 and ask for the WEEE associ
9. or or rental component Additionally items covered by the standard Trimble one year warranty are the accessories All other components not manufactured Trimble but sold as a part of the system such as tripods and grade rods will carry a 90 days warranty or the manufacturer s warranty whichever is greater Trimble or its Authorized Service Center will repair or replace at its option any defective part or components of which notice has been given during the warranty period A Warranty Registration Card must be filled out properly and on file with Trimble Service Department before warranty repair or replacement can be approved Travel and per diem expenses if required to and from the place where repairs are made will be charged to the purchaser at the prevailing rates Customers should send products to the nearest Authorized Factory Service Center for warranty repairs freight prepaid In countries with Trimble Service Subsidiary Centers the repaired products will be returned to the customer freight prepaid 22 Checking Accuracy Level Distance Between Walls T s e H 3 f 4 _ _ gt 1 In an area with at least 6 m 20 ft between two parallel walls place the laser 50 75 mm 2 3 in from one wall facing the wall 2 Press the power button 3 Locate the position of the level beam on the wall and make a mark 4 Rotate the laser 180 so that the laser faces the other wall 5
10. t 1 hour on off selectable CAUTION Do not store the laser in a wet pouch carrying case Holding the power button If the pouch carrying case gets wet let it dry before storing the down for 3 seconds laser in it enables auto shutoff Operating Temperature Range 10 C to 45 C 14 F to 113 F CAUTION The batteries should be removed when storing the Size 12 0 x 11 0 x 6 5 cm 4 7 x 4 4 x 2 6 in laser more than 30 days Weight 0 4 kg 0 9 Ib Battery Disposal When operated within specified temperature range Some states and local areas have regulations regarding the disposal of batteries Be sure to dispose of discharged batteries properly 9 10 at he ala Calibration Before each use be sure to check the pocket laser for signs of damage If the laser has been dropped or subjected to other rough treatment it should be checked for accuracy Checking Accuracy Plumb 1 Press the power button 2 Place the laser so that its down beam is over a reference mark on the floor 3 Locate the position of the up beam on the ceiling and make a mark Ag Checking Level to Square Beam 90 Calibration LP40 only Refer to the graphic for the location of the LP40 at each step and for the location of the marks made at each step All marks can be made on the floor by placing a target in front of the level or square beam and transferring the location to the floor

Trimble Outdoors LP20 User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents