Home

TP-Link TL-SL3428 V3 CLI Reference Guide

1. The number of the port desired to bind ranging from 1 to 28 Command Mode Global Configuration Mode Example Bind policy1 to Port 1 TP LINK config acl bind to port policy1 1 acl bind to vlan Description The acl bind to vlan command is used to bind a policy to a VLAN To cancel the bind relation please use no policy to vlan command Syntax acl bind to vlan policy name vlan id no policy to vlan policy name vlan id Parameter policy name The name of the policy desired to bind vlan id The ID of the VLAN desired to bind ranging from 1 to 4094 Command Mode 141 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Global Configuration Mode Example Bind policy1 to VLAN 2 TP LINK config acl bind to vlan policy1 2 show acl time segment Description The show acl time segment command is used to display the configuration of Time Range Syntax show acl time segment Command Mode Any Configuration Mode Example Display the configuration of Time Range TP LINK gt show acl time segment show acl holiday Description The show acl holiday command is used to display the defined holiday Syntax show acl holiday Command Mode Any Configuration Mode Example Display the defined holiday TP LINK gt show acl holiday show acl config Description The show acl config command is used to display the configuration of ACL 142 TL SL3428 JetStream L2 Manage
2. UDP port which is used to send notifications The UDP port functions with the IP address for the notification sending By default it is 162 user name The User name of the management station smode The Security Model of the management station with v1 v2c and v3 options By default the option is v1 slev The Security Level of SNMP v3 Group There are three options including noAuthNoPriv no authorization and no encryption authNoPriv authorization and no encryption and authPriv authorization and encryption By default the option is noAuthNoPriv type The type of the notifications with trap and inform options Trap indicates traps are sent while inform indicates informs are sent The inform type has a higher security than the trap type and resend and timeout need to be configured if you select this option You can only select the trap type in Security Model v1 By default the type of the notifications is trap resend The amount of times the switch resends an inform request ranging from 1 to 255 The switch will resend the inform request if it doesn t get the response from the management station during the Timeout interval and it will terminate resending the inform request if the resending times reach the specified Retry times 172 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide timeout The maximum time for the switch to wait for the respo
3. 33 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Syntax interface range link aggregation group list no interface range link aggregation group list Command Mode Global Configuration Mode Parameter group list The aggregation group list You can configure some aggregation groups at the same time Example Access the Interface range Link aggregation Mode and configure the aggregation group 1 4 6 TP LINK config interface range link aggregation 1 4 6 TP LINK config if link aggregation Description The link aggregation command is used to add the current Ethernet port to an aggregation group To remove the current Ethernet port from the aggregation group please use no link aggregation command Syntax link aggregation group num no link aggregation Parameter group num The LAG number ranging from1 to 14 Command Mode Interface Configuration Mode interface ethernet interface range ethernet Example Add the Ethernet port 2 4 to aggregation group 1 TP LINK config interface range ethernet 2 4 TP LINK config if link aggregation 1 34 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide link aggregation hash algorithm Description The link aggregation hash algorithm command is used to configure the Aggregate Arithmetic for LAG Syntax link aggregation hash algorithm src_dst_mac src_dst_ip Parameter src_dst_mac
4. The shared password for the switch and the authentication servers to exchange messages which contains 15 characters at most Command Mode Global Configuration Mode Example Configure the shared password for the switch and the authentication servers as tplink TP LINK config radius authentication key tplink radius accounting enable Description The radius accounting enable command is used to enable the accounting feature To disable the accounting feature please use no radius accounting enable command Syntax 74 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide radius accounting enable no radius accounting enable Command Mode Global Configuration Mode Example Enable the accounting feature TP LINK config radius accounting enable radius accounting primary ip Description The radius accounting primary ip command is used to configure the IP address of the accounting server Syntax radius accounting primary ip p addr Parameter ip addr The IP address of the accounting server Command Mode Global Configuration Mode Example Configure the IP address of the accounting server as 10 20 1 100 TP LINK config radius accounting primary ip 10 20 1 100 radius accounting secondary ip Description The radius accounting secondary ip command is used to configure the IP address of the alternate accounting server To restore to the default configuration please use
5. TP LINK config mirror remove mirrored 1 2 4 1 show mirror Description The show mirror command is used to display the configuration of mirror group Syntax show mirror group num Parameter group num The group number of mirror group Command Mode Any Configuration Mode Example Display configuration of mirror group 1 TP LINK show mirror 1 128 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Chapter 22 Port isolation Commands Port Isolation provides a method of restricting traffic flow to improve the network security by forbidding the port to forward packets to the ports that are not on its forwarding port list port isolation Description The port isolation command is used to configure the forward portlist of a port so that this port can only communicate with the ports on its portlist To delete the corresponding configuration please use no port isolation command Syntax port isolation forward list no port isolation Parameter forward list portlist of forward port It is multi optional Command Mode Interface Configuration Mode Example Configure port 1 and port 2 can only forward packets to port 6 and port 13 TP LINK config interface range ethernet 1 2 TP LINK config if port isolation 6 13 show port isolation Description The show port isolation command is used to display the forward portlist of a port Syntax show port isolation port Para
6. again please use no shutdown command Syntax shutdown no shutdown 111 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Command Mode Interface Configuration Mode interface ethernet interface range ethernet Example Disable Ethernet port3 TP LINK config interface ethernet 3 TP LINK config if shutdown flow control Description The flow control command is used to enable the flow control function for a port To disable the flow control function for this corresponding port please use no flow control command With the flow control function enabled the Ingress Rate and Egress Rate can be synchronized to avoid packets drop in the network Syntax flow control no flow control Command Mode Interface Configuration Mode interface ethernet interface range ethernet Example Enable the flow control function for Ethernet port 5 TP LINK config interface ethernet 5 TP LINK config if flow control negotiation Description The negotiation command is used to configure the Negotiation Mode for an Ethernet port To return to the default configuration please use no negotiation command Syntax negotiation auto 10h 10f 100h 100f 1000f no negotiation 112 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Parameter auto Auto negotiation default 10h 10Mbps half duplex 10f 10Mbps full duplex 100h 100Mbps
7. dhcp snooping trusted no dhcp snooping trusted Command Mode 54 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Interface Configuration Mode interface ethernet interface range ethernet Example Configure the port 2 to be a Trusted Port TP LINK config interface ethernet 2 TP LINK config if dhcp snooping trusted dhcp snooping mac verify Description The dhcp snooping mac verify command is used to enable the MAC Verify feature To disable the MAC Verify feature please use no dhcp snooping mac verify command There are two fields of the DHCP packet containing the MAC address of the Host The MAC Verify feature is to compare the two fields and discard the packet if the two fields are different Syntax dhcp snooping mac verify no dhcp snooping mac verify Command Mode Interface Configuration Mode interface ethernet interface range ethernet Example Enable the MAC Verify feature for the port 2 TP LINK config interface ethernet 2 TP LINK config if dhcp snooping mac verify dhcp snooping rate limit Description The dhcp snooping rate limit command is used to enable the Flow Control feature for the DHCP packets The excessive DHCP packets will be discarded To restore to the default configuration please use no dhcp snooping rate limit command Syntax 55 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide dhcp snooping rate limit value
8. 64 hexadecimal characters which must be even number meanwhile Command Mode Global Configuration Mode Example Enable the SNMP function and specify the Local Engine ID as 1234567890 the Remote Engine ID as 123456abcdef TP LINK config snmp global status enable engine id 1234567890 remote id 123456abcdef 167 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide snmp view add Description The snmp view add command is used to add View To delete the corresponding View please use no snmp view add command The OID Object Identifier of the SNMP packets is used to describe the managed objects of the switch and the MIB Management Information Base is the set of the OIDs The SNMP View is created for the SNMP management station to manage MIB objects Syntax snmp view add name mib oid include exclude no snmp view add name mib oid Parameter name The entry name of View ranging from 1 to 16 characters Each View can include several entries with the same name mib oid MIB Object ID It is the Object Identifier OID for the entry of View ranging from 1 to 61 characters include exclude View Type with include and exclude options They represent the view entry can cannot be managed by the SNMP management station individually Command Mode Global Configuration Mode Example Add a View named view1 configuring the OID as 1 3 6 1 6 3 20 and this OID can be ma
9. Description The show arp detection statistic command is used to display the number of the illegal ARP packets received Syntax show arp detection statistic Command Mode Any Configuration Mode Example Display the number of the illegal ARP packets received TP LINK config show arp detection statistic show arp detection statistic reset Description The show arp detection statistic reset command is used to clear the statistic of the illegal ARP packets received Syntax show arp detection statistic reset Command Mode Global Configuration Mode Example Clear the statistic of the illegal ARP packets received TP LINK config show arp detection statistic reset 63 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Chapter 12 DoS Defend Command DoS Denial of Service Attack is to occupy the network bandwidth maliciously by the network attackers or the evil programs sending a lot of service requests to the Host With the DoS Defend enabled the switch can analyze the specific field of the received packets and provide the defend measures to ensure the normal working of the local network dos prevent Description The dos prevent command is used to enable the DoS defend function globally To disable the DoS defend function please use no dos prevent command Syntax dos prevent no dos prevent Command Mode Global Configuration Mode Example Enable the DoS defend function globally TP
10. Description The show port rate limit command is used to display the rate limit information of an Ethernet port Syntax show port rate limit interface num Parameter port The port number of the port selected to display the rate limit information It ranges from 1 to 28 By default the rate limit information of all ports is displayed Command Mode 117 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Any Configuration Mode Example Display the rate limit information of all Ethernet ports TP LINK config show port rate limit 118 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Chapter 20 QoS Commands QoS Quality of Service function is used to optimize the network performance It provides you with network service experience of a better quality qos Description The qos command is used to configure CoS Class of Service based on port To return to the default configuration please use no qos command Syntax qos cos id no qos Parameter cos id The priority of port It ranges from O to 7 which represent CoSO CoS1 CoS2 CoS3 CoS4 CoS5 CoS6 CoS7 respectively By default the priority is 0 Command Mode Interface Configuration Mode interface ethernet interface range ethernet User Guidelines Port priority is one property of the port When the port priority is specified the data will be classified into the egress queue bas
11. Syntax show spanning tree security port defend port Parameter port The port selected to display the configuration ranging from 1 to 28 By default the Port Protect configuration of all ports is displayed Command Mode Any Configuration Mode Example Display the Port Protect configuration of port 2 TP LINK config show spanning tree security port defend 2 154 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Chapter 25 IGMP Commands IGMP Snooping Internet Group Management Protocol Snooping is a multicast control mechanism running on Layer 2 switch It can effectively prevent multicast groups being broadcasted in the network igmp snooping global Description The igmp snooping global command is used to configure IGMP globally To return to the default configuration please use no igmp global snooping command Syntax igmp snooping global status disable enable unknown packet pass discard no igmp snooping global Parameter status Enable Disable IGMP Snooping function globally on the switch By default it is disabled unknown packet The operation for the switch to process unknown multicast with pass and discard options Command Mode Global Configuration Mode Example Enable IGMP Snooping function and specify the operation to process unknown multicast as discard TP LINK config igmp snooping global status enable unknown packet discard
12. no radius accounting key Parameter key string The shared password for the switch and the accounting servers to exchange messages which contains 15 characters at most Command Mode Global Configuration Mode Example Configure the shared password for the switch and the accounting servers as tplink TP LINK config radius accounting key tplink radius response timeout Description The radius response timeout command is used to configure the maximum time for the switch to wait for the response from the RADIUS authentication and the accounting server To restore to the default value please use no radius response timeout command Syntax radius response timeout time no radius response timeout Parameter time The maximum time for the switch to wait for the response before resending a request to the supplicant ranging from 1 to 9 in second By default itis 3 Command Mode 77 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Global Configuration Mode Example Configure the maximum time for the switch to wait for the response from the RADIUS authentication and the accounting server as 5 seconds TP LINK config radius response timeout 5 show dot1x global Description The show dot1x global command is used to display the global configuration of 801 X Syntax show dot1x global Command Mode Any configuration Mode Example Display the configuration of 801 X globa
13. CONMIG mita AS E S OT E E rr ito diana 121 gos scheduler otitis A it 122 SHOW GOS POMM DaSOd ui ts 123 SNOW GOS Gott tcs eii 124 vii TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide SNOW GOS ASCP Aea a a dano devalues OREA 124 SHOW GOS sehed le resin opd Ad dance ved E AT ea aae TAAS aiani 124 Chapter 21 Port Mirror COMMANAS ccoooonnnnnnnicececenonononannnnncnonnnnnnnnnnnnnnennnnnnnnnanos 126 MU e aa a e aa e ea 126 mirror FEMOVE DOUE 127 NO 127 SITONA ATAKO pA eA EARS e oa 128 Chapter 22 Port isolation Commands ooooonnnnnccccccccononnnnnnnnccnnnnnnnnannnnnnnennnnnnnnnnanas 129 POIS MOM A A da 129 SNOOWPOMASO AMO it A A A E 129 Chapter 23 ACL ComMandSicnccenscscicsecccectccssesisssceiecscncsnsssseneedsceceincnersnseceeceseosinns 131 ACI time segment eee ee eee ee eee eee 131 AaChedittiMe SCQME NT uta A AAA Ae Aes 132 ACI MONG AY 252 sees leeaeeee a E aad ee dekh a Re ed Teale 133 ACI COALS at iate sd eta 133 acl rule MAA a ng Ae ten es a 134 achedit tule Macrae ui AAA oe eee 135 ACI PUIG Stach assist cates n aaah ori Pea AA sie kn 136 achedit rule Std aGls 3 24 8 20 0 tes A ive A ie ee E A es 137 ACI policy Poly AA secs vests aba elt eets A A ee 138 acl policy actlon add tt eR a ae Re 139 ACI edit CM ist tee Od Matta A ena eg 140 ACI DING O PU ye iia tases A NA en Seatac A 141 ACUDA OV Ar asa Seca e es a dE let SM og 141 show acl time SEGMeN iia A is ea ed nee heey 142 SHOW
14. RSTP Rapid Spanning Tree Protocol and MSTP Multiple Spanning Tree Protocol By default the STP version is STP cist CIST Priority which must be multiple of 4096 ranging from 0 to 61440 By default the CIST priority is 32768 CIST Priority is an important criterion on determining the root bridge In the same condition the switch with the highest priority will be chosen as the root bridge The lower value has the higher priority hello time Hello Time which is the interval to send BPDU packets and used to test the links Hello Time ranges from 1 to10 in seconds and it is 2 by default Otherwise 2 Hello Time 1 lt Max Age max age Max Age which is the maximum time the switch can wait without receiving a BPDU before attempting to reconfigure Max Age ranges from 6 to 40 in seconds By default it is 20 forward delay Forward Delay which is the time for the port to transit its state after the network topology is changed Forward Delay ranges from 4 to 30 in seconds and it is 15 by default Otherwise 2 Forward Delay 1 gt Max 144 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Age hold count TxHold Count which is the maximum number of BPDU packets transmitted per Hello Time interval TxHold Count ranges from 1 to 20 in pps By default it is 5 max hops Max Hops which is the maximum number of hops that occur in a specific region before
15. The desired instance ID for its port configuration ranging from 1 to 8 pri Port Priority which must be multiple of 16 ranging from 0 to 240 By default it is 128 Port Priority is an important criterion on determining if the port will be chosen as the root port by the device connected to this port path Path Cost which is used to choose the path and calculate the path costs of ports in an MST region It is an important criterion on determining the root port The lower value has the higher priority Command Mode Interface Configuration Mode interface ethernet interface range ethernet Example Configure the priority of port 5 in instance 1 as 64 and Path Cost as 100 TP LINK config interface ethernet 5 TP LINK config if spanning tree msti 1 pri 64 path 100 148 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide spanning tree tc defend Description The spanning tree tc defend command is used to configure the TC Protect of Spanning Tree globally To return to the default configuration please use no spanning tree tc defend command A switch removes MAC address entries upon receiving TC BPDUs If a malicious user continuously sends TC BPDUs to a switch the switch will be busy with removing MAC address entries which may decrease the performance and stability of the network Syntax spanning tree tc defend threshold threshold period period no spanning tree tc defend Parameter
16. The source and destination MAC addresses src_dst_ip The source and destination IP addresses Command Mode Global Configuration Mode Example Configure the Aggregate Arithmetic for LAG as src_dst_mac TP LINK config link aggregation hash algorithm src_dst_mac description Description The description command is used to set a description for an aggregation group To remove the description of an aggregation group please use no description command Syntax description description no description Parameter description The description of LAG which contains 16 characters at most Command Mode Interface Configuration Mode interface link aggregation Example Set the description movie server for aggregation group1 35 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide TP LINK config interface link aggregation 1 TP LINK config if description movie server show interface link aggregation Description The show interface link aggregation command is used to display the configuration information of the Aggregate Arithmetic and the aggregation groups Syntax show interface link aggregation group num Parameter group num The LAG number ranging from1 to 14 By default the LAG configuration information of all the Ethernet ports is displayed Command Mode Any Configuration Mode Example Display the LAG configuration information of all the Ethernet ports
17. threshold TC Threshold ranging from 1 to 100 packets By default it is 20 TC Threshold is the maximum number of the TC BPDUs received by the switch in a TC Protect Cycle period TC Protect Cycle ranging from 1 to 10 in seconds By default it is 5 Command Mode Global Configuration Mode Example Configure TC Threshold as 30 packets and TC Protect Cycle as 10 seconds TP LINK config spanning tree tc defend threshold 30 period 10 spanning tree security Description The spanning tree security command is used to configure MSTP Port Protect To return to the default configuration please use no spanning tree security command Port Protect function is to prevent the devices from any malicious attack against STP features Syntax spanning tree security loop disable enable root disable enable TC disable enable defend disable enable hold disable enable no spanning tree security 149 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Parameter loop Enable Disable Loop Protect By default it is disabled Loop Protect is to prevent the loops in the network brought by recalculating STP because of link failures and network congestions root Enable Disable Root Protect By default it is disabled Root Protect is to prevent wrong network topology change caused by the role change of the current legal root bridge TC Enable Disable
18. 1X Commands IEEE 802 1X function is to provide an access control for LAN ports via the authentication Only the supplicant passing the authentication can access the LAN dot1x Description The dot1x command is used to enable the IEEE 802 1X function globally To disable the IEEE 802 1X function please use no dot1x command Syntax dot1x no dot1x Command Mode Global Configuration Mode Example Enable the IEEE 802 1X function TP LINK config dot1x dot1x auth method Description The dot1x auth method command is used to configure the Authentication Method of IEEE 802 1X To restore to the default 802 1x authentication method please use no dot1x auth method command Syntax dot1x auth method pap eap md5 no dot1x auth method Parameter pap eap md5 Authentication Methods PAP IEEE 802 1X authentication system uses extensible authentication protocol EAP to exchange information between the switch and the client The 66 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide transmission of EAP packets is terminated at the switch and the EAP packets are converted to the other protocol such as RADIUS packets for transmission EAP MD5 IEEE 802 1X authentication system uses extensible authentication protocol EAP to exchange information between the switch and the client The EAP protocol packets with authentication data can be encapsulated in the advanced protocol su
19. GVRP registration type on the desired port To restore to the default value please use no gvrp registration command Syntax gvrp registration normal fixed forbidden no gvrp registration Parameter normal fixed forbidden Registration mode By default the registration mode is normal Command Mode Interface Configuration Mode interface ethernet interface range ethernet Example Configure the GVRP registration mode on the port 2 6 to fixed TP LINK config interface range ethernet 2 6 TP LINK config if gvrp registration fixed gvrp timer Description The gvrp timer command is used to set a GVRP timer for the desired port To restore to the default setting of a GARP timer please use no gvrp timer command Syntax gvrp timer leaveall join leave value 30 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide no gvrp timer leaveall join leave Parameter leaveall join leave They are the three timers leave All join and leave Once the LeaveAll Timer is set the port with GVRP enabled can send a LeaveAll message after the timer times out so that other GARP ports can re register all the attribute information After that the LeaveAll timer will start to begin a new cycle To guarantee the transmission of the Join messages a GARP port sends each Join message two times The Join Timer is used to define the interval between the two sending operations of
20. IEEE 802 1Q tag are mapped to different priority levels based on IEEE 802 1P priority mode if IEEE 802 1P Priority is enabled the untagged non IP datagram are mapped based on port priority mode Syntax qos dscp config dscp list tc id no qos dscp config Parameter 121 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide dscp list List of DSCP value One or several DSCP values can be typed using comma to separate Use a hyphen to designate a range of values for instance 1 4 7 11 indicates choosing 1 4 5 6 7 11 The DSCP value ranges from 0 to 63 tc id The priority level the packets with tag are mapped to It ranges from 0 to 3 which represent TCO TC1 TC2 TC3 respectively Command Mode Global Configuration Mode User Guidelines 1 By default DSCP values 0 15 are mapped to TCO DSCP values 16 31 are mapped to TC1 DSCP values 32 47 are mapped to TC2 and DSCP values 48 63 are mapped to TC3 2 Among the priority levels TCO TC3 the bigger value the higher priority Example Map DSCP values 10 11 15 to TCO TP LINK config qos dscp config 10 11 15 0 qos scheduler Description The qos scheduler command is used to configure the Schedule Mode To return to the default configuration please use no qos scheduler command When the network is congested the program that many packets complete for resources must be solved usually in the way of queue scheduling The switch will co
21. Interface Ethernet Configure parameters for several Ethernet ports c Interface link aggregation Configure parameters for a link aggregation such as broadcast storm d Interface range link aggregation Configure parameters for multi trunks e Interface vlan Configure parameters for the vlan port e Vlan Configuration Mode In this mode users can create a VLAN and add a specified port to the VLAN 3 Some commands are global that means they can be performed in all modes e show display all information of switch for example statistic information port information VLAN information 10 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide e history Display the commands history 1 3 Security Levels This switch s security is divided into two levels User level and Admin level User level only allows users to do some simple operations in User EXEC Mode Admin level allows you to monitor configure and manage the switch in Privileged EXEC Mode Global Configuration Mode Interface Configuration Mode and VLAN Configuration Mode Users get the privilege to the User level once connecting console port with the switch or logging in by Telnet However Guest users are restricted to access the CLI Users can enter Privileged EXEC mode from User EXEC mode by using the enable command In default case no password is needed In Global Configuration Mode you can configure password for Admin level
22. JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Any Configuration Mode Example Display the schedule rule of the egress queues TP LINK show gos scheduler 125 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Chapter 21 Port Mirror Commands Port Mirror refers to the process of forwarding copies of packets from one port to a mirroring port Usually the mirroring port is connected to data diagnose device which is used to analyze the mirrored packets for monitoring and troubleshooting the network mirror add Description The mirror add command is used to enable Port Mirror function Syntax mirror add mirrored port mirroring port none ingress egress both group num Parameter mirrored port The port to be monitored mirroring port The mirroring port none Remove the mirrored port from the current mirror group ingress Ingress monitoring Select this option the incoming packets received by the mirrored port will be copied to the mirroring port egress Egress monitoring Select this option the outgoing packets sent by the mirrored port will be copied to the mirroring port both Ingress and Egress monitoring Select this option the incoming packets received and the outgoing packets sent by the mirrored port will both be copied to the mirroring port group num The group number of mirror group Command Mode Gl
23. MAC address vian id The VLAN ID contained in the rule ranging from 1 to 4094 Ethernet type EtherType contained in the rule in the format of 4 hex number user pri The user priority contained in the rule ranging from O to 7 By default it is not limited time segment The time range for the rule to take effect By default it is not limited index Change the index number of the entry Command Mode Global Configuration Mode Example Edit the MAC ACL whose ID is 20 and add Rule 10 for it In the rule the source MAC address is 00 01 3F 48 16 23 the source MAC address mask is 11 11 11 11 11 00 VLAN ID is 2 the user priority is 5 the time range for the rule to take effect is tSeg1 and the packets match this rule will be forwarded by the switch TP LINK config acl edit rule mac acl 20 10 op permit smac 00 01 3F 48 16 23 smask 11 11 11 11 11 00 vid 2 pri 5 tseg tSeg1 acl rule std acl Description The acl rule std acl command is used to add Standard IP ACL rule To delete the corresponding rule please use no acl rule std acl command Standard IP ACLs analyze and process data packets based on a series of match conditions which can be the source IP addresses and destination IP addresses carried in the packets Syntax acl rule std acl acl id rule id op discard permit sip source ip smask 136 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide
24. Managed Switch CLI Guide Command Mode Global Configuration Mode Example Add a filtering address entry whose VLAN ID is 1 and MAC address is 00 1e 4b 04 01 5d TP LINK config bridge address filtering 00 1e 4b 04 01 5d 1 show bridge port security Description The show bridge port security command is used to configure the Port Security for each port such as configure the Max number of MAC addressed that can be learned on the port and the Learn Mode Syntax show bridge port security port num Parameter port num The port number of the switch It ranges from 1 to 28 By default the Port Security configuration of all ports is displayed Command Mode Any Configuration Mode Example Display the Port Security configuration of port2 TP LINK config show bridge port security 2 show bridge address Description The show bridge address command is used to display the information of all Address entries Syntax show bridge address dynamic static filter all Parameter dynamic static filter all the type of your desired entry Command Mode 96 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Any Configuration Mode Example Display the information of all Address entries TP LINK config show bridge address all show bridge aging time Description The show bridge aging time command is used to display the Aging Time of the MAC address Syntax sh
25. Mode Example Specify the maximum number of the connections to the SSH server as 3 TP LINK config ssh max client 3 ssh download Description The ssh max client command is used to download the SSH key file from TFTP server Syntax ssh download v1 v2 key file ip address p addr Parameter v1 v2 Select the type of SSH key to download v1 represents SSH 1 v2 represents SSH 2 key file The name of the key file which is selected to download The length of the name ranges from 1 to 25 characters The key length of the downloaded file must be in the range of 256 to 3072 bits ip addr The IP address of the TFTP server Command Mode Global Configuration Mode Example Download a SSH 1 type key file named ssh key from TFTP server with the IP Address 192 168 0 148 TP LINK config ssh download v1 ssh key ip address 192 168 0 148 show ssh Description The show ssh command is used to display the global configuration of SSH Syntax show ssh Command Mode Any Configuration Mode 88 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Example Display the global configuration of SSH TP LINK config show ssh 89 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Chapter 16 SSL Commands SSL Secure Sockets Layer a security protocol is to provide a secure connection for the application layer protocol e g HTTP based on TCP Adopting
26. Panel OvisLink Wireless Client pS Set Program Access and Utility o Defaults el HyperTerminal a Printers and Faxes IxC IxChariot Console Help and Support Search Aliprograms gt Pl Log Off fo Turn OFF Computer Figure 1 6 Open the Run window 3 Type cmd in the prompt Run window as figure 1 7 and click OK Type the name of a program folder document or Internet resource and Windows will open it for you Open Ei x Cancel Browse Figure 1 7 Run Window 4 Type telnet 192 168 0 1 in the command prompt shown as figure1 8 and press the Enter button TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide WINDOWS system32 cmd Figure 1 8 Connecting to the Switch 5 Type the User name and Password the factory default value for both of them is admin and press the Enter button then you can use the CLI now which is shown as figure1 9 ei Telnet 192 168 0 1 Jal x User Access Login Figure 1 9 Log in the Switch 1 2 CLI Command Modes The CLI is divided into different command modes User EXEC Mode Privileged EXEC Mode Global Configuration Mode Interface Configuration Mode and VLAN Database VLAN Configuration Mode Interface Configuration Mode can also be divided into Interface Ethernet Interface link aggregation and some other modes which is shown as the following diagram TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch C
27. SNMP v3 is authenticated by USM mechanism By default the Security Model is v1 slev The Security Level of SNMP v3 Group There are three options including noAuthNoPriv no authorization and no encryption authNoPriv authorization and no encryption and authPriv authorization and encryption By default the Security Level is noAuthNoPriv There is no need to configure this in SNMP v1 Model and SNMP v2c Model ro view Read only view The management access is restricted to read only and changes cannot be made to the assigned SNMP View wo view Write only view The management access is writing only and changes can be made to the assigned SNMP View The View defined both as the Read View and the Write View can be read and modified notify view Notify view The management station software can receive trap messages of the assigned SNMP view generated by the Switch s SNMP agent Command Mode Global Configuration mode Example Add group 1 configure its Security Model as SNMP v2c view1 can be read and edited by group member and the trap messages sent by view2 can be received by Management station TP LINK config snmp group add group1 smode v2c ro view1 wo view1 notify view2 169 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide snmp user add Description The snmp user add command is used to add User To delete the corresponding User please use no snmp user add
28. TC Protect By default it is disabled defend Enable Disable BPDU Protect By default it is disabled BPDU Protect is to prevent the edge port from being attacked by maliciously created BPDUs hold Enable Disable BPDU Filter By default it is disabled BPDU Filter is to prevent BPDUs flood in the STP network Command Mode Interface Configuration Mode interface ethernet interface range ethernet Example Enable Loop Protect Root Protect TC Protect BPDU Protect and BPDU Filter for port 2 TP LINK config interface ethernet 2 TP LINK config if spanning tree security loop enable root enable TC enable defend enable hold enable spanning tree mcheck Description The spanning tree mcheck command is used to enable MCheck Syntax spanning tree mcheck Command Mode Interface Configuration Mode interface ethernet interface range ethernet Example Enable MCheck for port 2 TP LINK config interface ethernet 2 TP LINK config if spanning tree mcheck 150 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide show spanning tree global info Description The show spanning tree global info command is used to display the current status of Spanning Tree Syntax show spanning tree global info Command Mode Any Configuration Mode Example Display the current status of Spanning Tree TP LINK show spanning tree global info show spanning tree global config Description T
29. about the commands used for DoS defend and detecting the DoS attack Chapter 13 IEEE 802 1X Commands Provide information about the commands used for configuring IEEE 802 1X function Chapter 14 Log Commands Provide information about the commands used for configuring system log Chapter 15 SSH Commands Provide information about the commands used for configuring and managing SSH Security Shell Chapter 16 SSL Commands Provide information about the commands used for configuring and managing SSL Secure Sockets Layer Chapter 17 Address Commands Provide information about the commands used for Address configuration Chapter 18 System Commands Provide information about the commands used for configuring the System information and System IP reboot and reset the switch upgrade the switch system and other operations Chapter 19 Ethernet Configuration Commands Provide information about the commands used for configuring the Bandwidth Control Negotiation Mode and Storm Control for Ethernet ports Chapter 20 QoS Commands Provide information about the commands used for configuring the QoS function Chapter 21 Port Mirror Commands Provide information about the commands used for configuring the Port Mirror function Chapter 22 Port isolation Commands Provide information about the commands used for configuring the Port isolation function Chapter 23 ACL Commands Provide information about the commands used for configuring t
30. auto Port mode Command Mode Interface Configuration Mode interface ethernet interface range ethernet Example Configure Ethernet port 2 to operate in the manual voice VLAN mode TP LINK config interface ethernet 2 TP LINK config if switchport voice vlan mode manual show voice vlan global Description The show voice vlan global command is used to display the global configuration information of Voice VLAN Syntax show voice vlan global Command Mode Any Configuration Mode Example Display the configuration information of Voice VLAN globally TP LINK config show voice vlan global 27 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide show voice vlan oui Description The show voice vlan oui command is used to display the configuration information of Voice VLAN OUI Syntax show voice vlan oui Command Mode Any Configuration Mode Example Display the configuration information of Voice VLAN OUI TP LINK config show voice vlan oui show voice vlan switchport Description The show voice vlan switchport command is used to displays the configuration information of the port in the Voice VLAN Syntax show voice vlan switchport port Parameter port Ethernet port By default it will display the configuration information of all the ports in the Voice VLAN Command Mode Any Configuration Mode Example Display the configuration information of all the ports in the Voic
31. bridge address port security command Port Security is to protect the switch from the malicious MAC address attack by limiting the maximum number of the MAC addresses that can be learned on the port The port with Port Security feature enabled will learned the MAC address dynamically When the learned MAC address number reaches the maximum the port will stop learning Therefore the other devices with the MAC address unlearned can not access to the network via this port Syntax bridge address port security max number num mode dynamic static permanent status disable enable no bridge address port security Parameter num The maximum number of MAC addresses that can be learned on the port It ranges from 0 to 64 By default this value is 64 mode Learn mode for MAC addresses There are three modes including Dynamic mode Static mode and Permanent mode When Dynamic mode is selected the learned MAC address will be deleted automatically after the aging time When Static mode is selected the learned MAC address will be out of the influence of the aging time and can only be deleted manually The learned entries will be cleared after the switch is rebooted When permanent mode is selected the learned MAC address will be out of the influence of the aging time and can only be deleted manually too However the learned entries will be saved even the switch is rebooted status Enable or disable the Por
32. by enable password command Once password is configured you are required to enter it to access Privileged EXEC mode 1 4 Conventions 1 4 1 Format Conventions The following conventions are used in this Guide gt Items in square brackets are optional gt Items in braces are required gt Alternative items are grouped in braces and separated by vertical bars For example speed 10 100 1000 gt Bold indicates an unalterable keyword For example show logging gt Normal Font indicates a constant several options are enumerated and only one can be selected For example switchport type access trunk general gt Italic Font indicates a variable an actual value must be assigned For example bridge aging time aging time 1 4 2 Special Characters You should pay attentions to the description below if the variable is a character string gt These six characters lt gt amp can not be input TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide gt Ifa blank is contained in a character string single or double quotation marks should be used for example hello world hello world and the words in the quotation marks will be identified as a string Otherwise the words will be identified as several strings 1 4 3 Parameter Format Some parameters must be entered in special formats which are shown as follows gt MAC Address must be enter in the format of XX XX
33. config command is used to modify the multicast filtering IP range Syntax igmp snooping filter config ic start ip end ip Parameter id I P range ID ranging from 1 to 30 Start ip The start multicast IP of the IP range end ip The end multicast IP of the IP range Command Mode Global Configuration Mode Example Modify the multicast IP range whose ID is 20 as 225 0 0 10 225 0 0 12 TP LINK config igmp snooping filter config 20 225 0 0 10 225 0 0 12 igmp snooping filter Description The igmp snooping filter command is used to configure Port Filter To return to the default configuration please use no igmp snooping filter command When the switch receives IGMP report message it examines the multicast filtering IP ID configured on the access port to determine if the port can join the multicast group If the multicast IP is not filtered the switch will add the port to the forward port list of the multicast group Otherwise the switch will drop the IGMP report message In that way you can control the multicast groups that users can access Syntax igmp snooping filter status disable enable mode refuse accept addr id filter addr id maxgroup max group no igmp snooping filter Parameter status Enable Disable port multicast filtering function By default it is disabled mode Action Mode with refuse and accept options Refuse indicates only the multicast packets whose mul
34. cooooccoccconccooncnoncnoncnonenoneno nono nono nono ocn one none none none none aaa none aaa nn ne aaa 108 Chapter 19 Ethernet Configuration CommandS coooccccnncnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnna 110 interface ethernet aias ireira aea ED Eaa ad Re 110 interface range ethernet oooooccccnoncccnonococoncnnnccononcnnonncnnnncnnoncnnn nro nnnnnnnnnnannnnnnnnnnnncnneninnnnrenenin 110 CESCIIPUON ii AAA A ite aa ye SS 111 ANEA re LONA a EATE A A T A ta 111 TOWECONTTO aoe ta eS A AAA AA AA aus AS 112 NOJA OMR A ade A a ba 112 SOM CONTO cid a A ia 113 PO A A dead 114 port rate limit disable ingresS onoonccnccccccnnnncnccnnnnnnnonnnnnnnonononononnnnnnnnonononononononnnnncnnncnnnennss 114 port rate limit disable egress oooccccccccccncccncnnnnnnnnonnnnnnnononononononononnnnnnnnnnnnononononenonenoncnnncnnss 115 show interface CONfiguUratiON ooococononocooccccccococnnnnanncnnnnonnnnonnnnncnnnnnncnnoncnnnnnnnnnnnnnanannnnnnnnnnn 115 show interlaGe Status asirasi evens Hea Oa EE hide Weedeater 116 show interface COUNTENS c ccccceeeeeceeeeneaeeeceeeeeeeeceeaneeeeeeeeeseeeeaaeaeeeeeeeeseneeieaeeeeeeeeeeeseaas 116 show storm control ethernet 0 0 cee stents eee eee neo neon nono nn nana 117 SHOW port Tate Mid issii despot needa dhe ei eee an ea le 117 Chapter 20 QoS Commands ui aii 119 OS aia dada italia 119 OS DO penal ii A AA A A ESA 119 Gos dotip CONTO eeen a e A Otel eee 120 Os ASP enable imac lla 121 COS ASCH
35. detection recover Description The arp detection recover command is used to restore to the port to the ARP transmit status from the ARP filter status Syntax arp detection recover Command Mode Interface Configuration Mode interface ethernet interface range ethernet Example Restore the port 5 to the ARP transmit status TP LINK config interface ethernet 5 61 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide TP LINK config if arp detection recover show arp detection global Description The show arp detection global command is used to display the ARP detection global configuration including the enable disable status and the Trusted Port list Syntax show arp detection global Command Mode Any Configuration Mode Example Display the ARP detection configuration globally TP LINK config show arp detection global show arp detection interface Description The show arp detection interface command is used to display the interface configuration of ARP detection Syntax show arp detection interface ethernet port num Parameter port num The number of switch port By default display the configuration of all the ports Command Mode Any Configuration Mode Example Display the configuration of all the ports TP LINK config show arp detection interface 62 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide show arp detection statistic
36. each Join message Once the Leave Timer is set the GARP port receiving a Leave message will start its Leave timer and unregister the attribute information if it does not receive a Join message again before the timer times out value The value of the timer The LeaveAll Timer ranges from 1000 to 30000 centiseconds and the default value is 1000 The Join Timer ranges from 20 to 1000 centiseconds and the default value is 20 The Leave Timer ranges from 60 to 3000 centiseconds and the default value is 60 Command Mode Interface Configuration Mode interface ethernet interface range ethernet Example Set the GARP leaveall timer of port 6 to 2000 centiseconds and restore to the join timer of it to the default value TP LINK config interface ethernet 6 TP LINK config if gvrp timer leaveall 2000 TP LINK config if no gvrp timer join show gvrp global Description The show gvrp global command is used to display the global GVRP status Syntax show gvrp global Command Mode Any Configuration Mode 31 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Example Display the global GVRP status TP LINK config show gvrp global show gvrp interface Description The show gvrp interface command is used to display the GVRP configuration information of the specified Ethernet ports Syntax show gvrp interface ethernet port num Parameter port num The Ethernet port number By defa
37. end time The end time of the time slice in the format of HH MM By default it is 24 00 week day Period Mode in the format of 1 3 6 or daily off day working day 1 3 6 represent Monday Tuesday Wednesday and Saturday daily represents every day off day represents weekend and working day represents working day By default the period mode is disabled start date The start date in Absoluteness Mode in the format of MM DD YYYY By default it is 01 01 1970 end date The end date in Absoluteness Mode in the format of MM DD YYYY By default it is 12 31 2099 The absoluteness mode will be disabled if the start date and end date are both not configured 131 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide holiday Enable Disable Holiday Mode By default it is disabled Command Mode Global Configuration Mode Example Add a time range named tSeg1 with time from 8 30 to 12 00 at working day TP LINK config acl time segment tSeg1 start time 08 30 end time 12 00 week day working day acl edit time segment Description The acl edit time segment command is used to edit Time Range Syntax acl edit time segment name start time start time end time end time week day week day start date start date end date end date holiday disable enable Parameter name The Time Range name ranging from 1 to 16 characters start time The start time of
38. if the port connected to this port will be chosen as the root port In the same condition the port with the highest priority will be chosen as the root port The lower value has the higher priority expath consum ExtPath Cost which is used to choose the path and calculate the path costs of ports in different MST regions It is an important criterion on determining the root port The lower value has the higher priority By default it is automatic inpath consum IntPath Cost which is used to choose the path and calculate the path costs of ports in an MST region It is an important criterion on determining the root port The lower value has the higher priority By default it is automatic edge Enable Disable Edge Port By default it is disabled The edge port can transit its state from blocking to forwarding rapidly without waiting for forward delay ptop The P2P link status with auto open and close options By default the option is auto If the two ports in the P2P link are root port or designated port they can transit their states to forwarding rapidly to reduce the unnecessary forward delay Command Mode Interface Configuration Mode interface ethernet interface range ethernet Example Enable the STP function of port 1 and configure the Port Priority as 64 ExtPath Cost as 100 IntPath Cost as 100 and then enable Edge Port TP LINK config interface ethernet 1 TP LINK config if spanning tree common confi
39. igmp snooping config Description The igmp snooping config status command is used to configure IGMP Snooping and Fast Leave function for port To return to the default configuration 155 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide please use no igmp snooping config command Syntax igmp snooping config status disable enable fast leave disable enable no igmp snooping config Parameter status Enable Disable IGMP Snooping for the desired port fast leave Enable Disable Fast Leave feature for the desired port If Fast Leave is enabled for a port the switch will immediately remove this port from the multicast group upon receiving IGMP leave messages Command Mode Interface Configuration Mode interface ethernet interface range ethernet Example Enable IGMP Snooping and Fast Leave function for port 5 TP LINK config interface ethernet 5 TP LINK config if igmp snooping config status enable fast leave enable igmp snooping vlan config add Description The igmp snooping vlan config add command is used to configure IGMP Snooping parameters for individual VLANs To delete the corresponding configuration for the certain VLAN please use no _ igmp snooping vlan config add command Multicast groups established by IGMP Snooping are based on VLANs You can configure different IGMP parameters for different VLANs Syntax igmp snooping vlan config add vlan id rtime router
40. is failed to establish TP LINK ping 192 168 0 131 n 8 1 512 tracert Description The tracert command is used to test the connectivity of the gateways during its journey from the source to destination of the test data Syntax tracert urh maxHops Parameter url The IP address of the destination device maxHops The maximum number of the route hops the test data can pass 105 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide though It ranges from 1 to 30 By default this value is 4 Command Mode User EXEC Mode and Privileged EXEC Mode Example Test the connectivity between the switch and the network device with the IP 192 168 0 131 If the destination device has not been found after 20 maxHops the connection between the switch and the destination device is failed to establish TP LINK tracert 192 168 0 131 20 loopback Description The loopback command is used to test whether the port is available or not Syntax loopback port internal external Parameter port The number of the port which is selected for loopback test It ranges from 1 to 28 internal external Loopback Type There are two options Internal and External Command Mode User EXEC Mode and Privileged EXEC Mode Example Do an Internal type loopback test for port 4 TP LINK loopback 4 internal show system info Description The show system info command is used to display Syst
41. no dhcp snooping rate limit Parameter value The value of Flow Control The options are 0 5 10 15 20 25 30 packet second The default value is 0 which stands for disable Command Mode Interface Configuration Mode interface ethernet interface range ethernet Example Set the Flow Control of port 2 as 20 pps TP LINK config interface ethernet 2 TP LINK config if dhcp snooping rate limit 20 dhcp snooping decline Description The dhcp snooping decline command is used to enable the Decline Protect feature To disable the Decline Protect feature please use no dhcp snooping decline command Syntax dhcp snooping decline no dhcp snooping decline Command Mode Interface Configuration Mode interface ethernet interface range ethernet Example Enable the Decline Protect feature of port 2 TP LINK config interface ethernet 2 TP LINK config if dhcp snooping decline show binding table Description 56 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide The show binding table command is used to display the IP MAC VID PORT binding table Syntax show binding table Command Mode Any Configuration Mode Example Display the IP MAC VID PORT binding table TP LINK config show binding table show dhcp snooping global Description The show dhcp snooping global command is used to display the global configuration of DHCP Snooping Syntax show dhcp snooping global Command
42. no dot1x timer Parameter period The value for Quiet Period ranging from 1 to 999 in seconds By default it is 10 Once the supplicant failed to the 802 1X Authentication then the switch will not respond to the authentication request from the same supplicant during the Quiet Period timeout The maximum time for the switch to wait for the response from supplicant before resending a request to the supplicant ranging from 1 to 9 in second By default it is 3 Command Mode 68 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Global Configuration Mode Example Configure the Quiet Period and the SupplicantTimeout as 12 seconds and 6 seconds TP LINK config dot1x timer quiet period 12 supp timeout 6 dot1x retry Description The dot1x retry command is used to configure the maximum transfer times of the repeated authentication request To restore to the default value please use no dot1x retry command Syntax dot1x retry retry time no dot1x retry Parameter retry time The maximum transfer times of the repeated authentication request ranging from 1 to 9 in times By default the value is 3 Command Mode Global Configuration Mode Example Configure the maximum transfer times of the repeated authentication request as 5 TP LINK config dot1x retry 5 dot1x Description The dot1x command is used to enable the IEEE 802 1X function for a specified port To di
43. ranging from 1 to 8 Command Mode Any Configuration Mode Example 152 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Display the configuration of instance 1 TP LINK config show spanning tree msti config 1 show spanning tree msti port Description The show spanning tree msti port command is used to display the Instance Port configuration of Spanning Tree Syntax show spanning tree msti port id port Parameter id Instance ID ranging from 1 to 8 port The port selected to display the configuration ranging from 1 to 28 By default the configuration of all ports is displayed Command Mode Any Configuration Mode Example Display the configuration of port 5 in Instance 1 TP LINK config show spanning tree msti port 1 5 show spanning tree security tc defend Description The show spanning tree security tc defend command is used to display TC Threshold and TC Protect Cycle of Spanning Tree Syntax show spanning tree security tc defend Command Mode Any Configuration Mode Example Display TC Threshold and TC Protect Cycle of Spanning Tree TP LINK config show spanning tree security tc defend 153 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide show spanning tree security port defend Description The show spanning tree security port defend command is used to display the Port Protect configuration of Spanning Tree
44. rmon event description index Parameter index The index number of the event entry ranging from 1 to 12 You can only select one entry for each command description The description of the event ranging from 1 to 16 characters By default it is empty Command Mode Global Configuration Mode Example Configure the description of entry 1 as description1 TP LINK config snmp rmon event description 1 description snmp rmon event type Description The snmp rmon event type command is used to configure the type of SNMP RMON Event To return to the default configuration please use no snmp rmon event type command Syntax snmp rmon event type index none log notify both no snmp rmon event type index Parameter index The index number of the entry ranging from 1 to 12 in the format of 1 3 5 none log notify both The event type with none log notify and both options None indicates no processing log indicates logging the event notify indicates sending trap messages to the management station and both indicates 176 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide logging the event and sending trap messages to the management station Command Mode Global Configuration Mode Example Configure the event type of entries 1 2 3 4 and 8 as log TP LINK config snmp rmon event type 1 4 8 log snmp rmon event owner Description The snmp rmon even
45. samplings from the port ranging from 10 to 3600 in seconds By default it is 1800 Command Mode 173 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Global Configuration Mode Example Configure the sample port as 1 and the sample interval as 100 seconds for the entries 1 3 TP LINK config snmp rmon history sample cfg 1 3 1 100 snmp rmon history owner Description The snmp rmon history owner command is used to configure the owner of the history sample entry To return to the default configuration please use no snmp rmon history owner command Syntax snmp rmon history owner index owner no snmp rmon history owner index Parameter index The index number of the sample entry ranging from 1 to 12 You can only select one entry for each command owner The owner of the history sample entry ranging from 1 to 16 characters By default it is monitor Command Mode Global Configuration Mode Example Configure the owner of entry 1 as owner TP LINK config snmp rmon history owner 1 owner snmp rmon history enable Description The snmp rmon history enable command is used to enable the history sample entry To disable the corresponding entry please use no snmp rmon history enable command Syntax snmp rmon history enable index 174 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide no snmp rmon history enable index Pa
46. tc id The egress queue the packets with tag are mapped to It ranges from 0 to 3 which represent TCO TC1 TC2 TC3 respectively Command Mode Global Configuration Mode User Guidelines 1 By default the mapping relation between tag and the egress queue is 0 TC1 1 TCO 2 TCO 3 TC1 4 TC2 5 TC2 6 TC3 7 TC3 2 Among the priority levels TCO TC3 the bigger value the higher priority 120 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Example Map tag value 0 to TC3 TP LINK config qos dot1p config 0 3 qos dscp enable Description The qos dscp enable command is used to enable the mapping relation between DSCP Priority and Egress Queue To disable the mapping relation please use no qos dscp enable command Syntax qos dscp enable no qos dscp enable Command Mode Global Configuration Mode Example Enable the mapping relation between DSCP Priority and Egress Queue TP LINK config qos dscp enable qos dscp config Description The qos dscp config command is used to configure the mapping relation between DSCP Priority and Egress Queue To return to the default configuration please use no qos dscp config command DSCP DiffServ Code Point is a new definition to IP ToS field given by IEEE This field is used to divide IP datagram into 64 priorities When DSCP Priority is enabled IP datagram are mapped to different priority levels based on DSCP priority mode non IP datagram with
47. the Protocol VLAN feature for a specified port To disable the Protocol VLAN feature of this port please use no protocol vlan interface command By default the Protocol VLAN feature of all ports is disabled Syntax protocol vlan vlan interface port list no protocol vlan interface port lisf Parameter port list The port numbers needed to be edited or canceled Command Mode Global Configuration Mode Example Enable the Protocol VLAN feature for the ports 1 4 6 9 11 TP LINK config protocol vlan vlan interface 1 4 6 9 11 22 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide show protocol vian template Description The show protocol vlan template command is used to display the information of the Protocol VLAN templates Syntax show protocol vlan template Command Mode Any Configuration Mode Example Display the information of the Protocol VLAN templates TP LINK config show protocol vlan template show protocol vlan vlan Description The show protocol vlan vlan command is used to display the information about Protocol VLAN entry Syntax show protocol vlan vlan Command Mode Any Configuration Mode Example Display information of the protocol vlan entry TP LINK config show protocol vlan vlan show protocol vlan interface Description The show protocol vlan interface command is used to display port state of Protocol VLAN Syntax show protocol vlan inter
48. 100 Itime 10 rport 1 igmp snooping vlan config Description The igmp snooping vlan config command is used to modify IGMP Snooping parameters for individual VLANs To return to the primary configuration of the corresponding VLAN please use no igmp snooping vlan config command Syntax igmp snooping vlan config v an id rtime router time mtime member time Itime eave time rport router porf no igmp snooping vlan config vlan id Parameter vian id The ID of the VLAN desired to modify configuration ranging from 1 to 4094 router time Router Port Time Within this time if the switch does not receive IGMP query message from the router port it will consider this port is not a router port any more Router Port Time ranges from 60 to 600 in seconds By 157 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide default it is 300 member time Member Port Time Within this time if the switch does not receive IGMP report message from the member port it will consider this port is not a member port any more Member Port Time ranges from 60 to 600 in seconds By default it is 260 leave time Leave Time which is the interval between the switch receiving a leave message from a host and the switch removing the host from the multicast groups Leave Time ranges from 1 to 30 in seconds By default it is 1 router port Static Router Port which is mainly used in the
49. 162 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide show igmp snooping port config port Parameter port The port selected to display the configuration ranging from 1 to 28 By default the configuration of all ports is displayed Command Mode Any Configuration Mode Example Display the IGMP configuration of port 2 TP LINK gt show igmp snooping port config 2 show igmp snooping vlan config Description The show igmp snooping vlan config command is used to display the VLAN configuration of IGMP Syntax show igmp snooping vlan config Command Mode Any Configuration Mode Example Display the VLAN configuration of IGMP TP LINK gt show igmp snooping vlan config show igmp snooping multi vlan Description The show igmp snooping multi vlan command is used to display the Multicast VLAN configuration Syntax show igmp snooping multi vlan Command Mode Any Configuration Mode Example Display the Multicast VLAN configuration 163 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide TP LINK gt show igmp snooping multi vlan show igmp snooping multi ip list Description The show igmp snooping multi ip list command is used to display the Multicast IP table Syntax show igmp snooping multi ip list Command Mode Any Configuration Mode Example Display the Multicast IP table TP LINK gt show igmp snooping multi ip list show igmp sno
50. 2 TP LINK config dhcp snooping information user defined dhcp snooping information remote id Description The dhcp snooping information remote id command is used to configure the sub option Remote ID for the customized Option 82 Syntax dhcp snooping information remote id string Parameter string Enter the sub option Remote ID which contains 32 characters at most Command Mode 53 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Global Configuration Mode Example Configure the sub option Remote ID for the customized Option 82 as tplink TP LINK config dhcp snooping information remote id tplink dhcp snooping information circuit id Description The dhcp snooping information circuit id command is used to configure the sub option Circuit ID for the customized Option 82 Syntax dhcp snooping information circuit id string Parameter string Enter the sub option Circuit ID which contains 32 characters at most Command Mode Global Configuration Mode Example Configure the sub option Circuit ID for the customized Option 82 as tplink TP LINK config dhcp snooping information circuit id tplink dhcp snooping trusted Description The dhcp snooping trusted command is used to configure a port to be a Trusted Port Only the Trusted Port can receive the DHCP packets from DHCP servers To turn the port back to a distrusted port please use no dhcp snooping trusted command Syntax
51. 23 VLAN1 and Port1 together TP LINK config bridge address static mac 00 02 58 4f 6c 23 vid 1 port 1 94 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide bridge aging time Description The bridge aging time command is used to configure aging time for the dynamic address To return to the default configuration please use no bridge aging time command Syntax bridge aging time aging time no bridge aging time Parameter aging time The aging time for the dynamic address The value of it can be 0 or ranges from 10 to 630 seconds When 0 is entered the Auto Aging function is disabled By default this value is 300 Command Mode Global Configuration Mode Example Configure the aging time as 500 seconds TP LINK config bridge aging time 500 bridge address filtering Description The bridge address filtering command is used to add the filtering address entry To delete the corresponding entry please use no bridge address filtering command The filtering address function is to forbid the undesired package to be forwarded The filtering address can be added or removed manually independent of the aging time Syntax bridge address filtering mac vid no bridge address filtering mac vid Parameter mac The MAC address to be filtered vid The corresponding VLAN ID of the MAC address It ranges from 1 to 4094 95 TL SL3428 JetStream L2 Managed Switch CLI Guide L2
52. 4m 5m 10m 20m 40m 50m Command Mode Interface Configuration Mode interface ethernet interface range ethernet Example Enable the Storm Control function for port5 and specify the rate as 128kbps TP LINK config interface ethernet 5 TP LINK config if storm control bc status enable mc status enable ul status enable rate 128k port rate limit Description The port rate limit command is used to configure the Rate Limit for an Ethernet port To disable the Rate Limit please use no port rate limit command Syntax port rate limit ingress ingress rate egress egress rate no port rate limit Parameter ingress rate Specify the bandwidth for receiving packets Range 1 102400 for the megaport 1 1024000 for the gigaport egress rate Specify the bandwidth for sending packets Range 1 102400 for the megaport 1 1024000 for the gigaport Command Mode Interface Configuration Mode interface ethernet interface range ethernet Example Configure the ingress rate as 5120Kbps and egress rate as 1024Kbps for port5 TP LINK config interface ethernet 5 TP LINK config if port rate limit ingress 5120 egress 1024 port rate limit disable ingress Description The port rate limit disable ingress command is used to disable the 114 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide ingress rate limit Syntax port rate limit disable ingress Command Mode Interface Configura
53. AN Command Mode Any Configuration Mode Example Display the information of vlan 5 TP LINK config show vian 5 show interface switchport Description The show interface switchport command is used to display the IEEE 802 1Q VLAN configuration information of the specified port Syntax show interface switchport port num Parameter port num The port number By default display the VLAN configuration information of all ports Command Mode Any Configuration Mode Example Display the VLAN configuration information of all ports TP LINK config show interface switchport 20 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Chapter 4 Protocol VLAN Commands Protocol VLAN Virtual Local Area Network is the way to classify VLANs based on Protocols A Protocol is relative to a single VLAN ID The untagged packets and the priority tagged packets matching the protocol template will be tagged with this VLAN ID protocol vlan template Description The protocol vlan template command is used to create or delete Protocol VLAN template Syntax protocol vlan template add protocol name ether type protocol vlan template remove index Parameter protocol name Give a name for the Protocol Template which contains 8 characters at most ether type Enter the Ethernet protocol type field in the protocol template composing 4 Hex integers index The number of the Pro
54. DHCP Snooping TP LINK config dhcp snooping information enable dhcp snooping information strategy Description The dhcp snooping information strategy command is used to select the operation for the Option 82 field of the DHCP request packets from the Host To restore to the default option please use no dhcp snooping information strategy command Syntax dhcp snooping information strategy keep replace drop no dhcp snooping information strategy Parameter keep Indicates to keep the Option 82 field of the packets It is the default option replace Indicates to replace the Option 82 field of the packets with the switch defined one drop Indicates to discard the packets including the Option 82 field Command Mode 52 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Global Configuration Mode Example Replace the Option 82 field of the packets with the switch defined one and then send out TP LINK config dhcp snooping information strategy replace dhcp snooping information user defined Description The dhcp snooping information user defined command is used to permit users to define the Option 82 To disable the function please use no dhcp snooping information user defined command Syntax dhcp snooping information user defined no dhcp snooping information user defined Command Mode Global Configuration Mode Example Permit users to define the Option 8
55. Guide TP LINK config interface ethernet 2 TP LINK config if switchport allowed vlan add 2 switchport pvid Description The switchport pvid command is used to configure the PVID for the switch ports Syntax switchport pvid vian id Parameter vlan id VLAN ID ranging from 1 to 4094 Command Mode Interface Configuration Mode interface ethernet interface range ethernet Example Specify the PVID of port 2 as 2 TP LINK config interface ethernet 2 TP LINK config if switchport pvid 2 switchport general egress rule Description The switchport general egress rule command is used to configure the egress rule of the general port Syntax switchport general egress rule vian id untagged tagged Parameter vlan id VLAN ID ranging from 1 to 4094 untagged tagged egress rule untagged or tagged Command Mode Interface Configuration Mode interface ethernet interface range ethernet Example Specify the egress rule of port 2 in vlan 3 as tagged 19 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide TP LINK config interface ethernet 2 TP LINK config if switchport general egress rule 3 tagged show vlan Description The show vian command is used to display the information of IEEE 802 1Q VLAN Syntax show vlan v an id Parameter vian id VLAN ID ranging from 1 to 4094 By default display all the information of IEEE 802 1Q VL
56. HOW SMMP FIMOM VOM eciconltn llas lille toren enan ARa kE 183 SNOW snmp rmon AalarM ooocncccnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnicnnnnnn 184 Chapter 27 Cluster COMMands ccceeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeneeeeeeeeeeeeeeeeaaaeees 185 CIUSTO RNP esca 185 CUSCO MOP kes wate elie dade eae Goan EA 186 Cluster exploren ti A el 187 CU eiii adas 187 cl ster manage Fol Change sresti cscs sees dteadee eases retenant naaa a dade dees 188 show cluster ndp global arestin a A hae nies 188 Show cluster ndp pOrt Status vi einsa ia ts 189 SHOW cluster NEIGH DOU second carol td its 189 show cluster ntdp global ooonconnconncconcconaconcno nono nono nono nono ncno nono nc no nen nena none ae none nana nenas 189 show cluster ntdp port status siira cece cece cece cece cece teen eee eect eee aaa aa O Eaa AE ra rar 190 show cluster Nd deV CE sss ti a a a aa anaa e raaa ide dashes A EA A reser erage 190 show cluster manage TO 8 ooooooonconncconcconcconononononono nono nono nono nen one none none none none none none nano nena nn names 191 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Preface This Guide is intended for network administrator to provide referenced information about CLI Command Line Interface The device mentioned in this Guide stands for TL SL3428 JetStream L2 Managed Switch Overview of this Guide Chapter 1 Using the CLI Provide inform
57. K config ssl download certificate ssl cert ip address 192 168 0 148 ssl download key Description The ssl download key command is used to download a SSL key to the switch from TFTP server Syntax ssl download key ss key ip address p addr Parameter ssi key The name of the SSL key which is selected to download to the switch The length of the name ranges from 1 to 25 characters The Key must be BASE64 encoded ip addr The IP address of the TFTP server Command Mode Global Configuration Mode Example Download a SSL Key named ssl key from TFTP server with the IP Address of 192 168 0 148 TP LINK config ssl download key ssl key ip address 192 168 0 148 show ssl Description The show ssl command is used to display the global configuration of SSL Syntax show ssl 91 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Command Mode Any Configuration Mode Example Display the global configuration of SSL TP LINK config show ssl 92 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Chapter 17 Address Commands Address configuration can improve the network security by configuring the Port Security and maintaining the address information by managing the Address Table bridge address port security Description The bridge address port security command is used to configure port security To return to the default configuration please use no
58. L SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Command Mode Global Configuration Mode Example Add static multicast IP address 225 0 0 1 which correspond to VLAN 2 and configure the forward port as port 1 TP LINK config igmp snooping static entry add 225 0 0 1 2 1 igmp snooping filter add Description The igmp snooping filter add command is used to configure the multicast IP range desired to filter To delete the corresponding IP range please use no igmp snooping filter add command When IGMP Snooping is enabled you can specified the multicast IP range the ports can join so as to restrict users ordering multicast programs via configuring multicast filter rules Multicast IP addresses ranges from 224 0 0 0 to 239 255 255 255 The range for receivers to join is from 224 0 1 0 to 239 255 255 255 Syntax igmp snooping filter add id start ip end ip no igmp snooping filter add ia Parameter id I P range ID ranging from 1 to 30 start ip The start multicast IP of the IP range end ip The end multicast IP of the IP range Command Mode Global Configuration Mode Example Add multicast IP range 225 0 0 1 225 0 0 4 to filter and specify the IP range ID as 20 TP LINK config igmp snooping filter add 20 225 0 0 1 225 0 0 4 igmp snooping filter config Description 160 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide The igmp snooping filter
59. LI Guide User EXEC Mode Password Privileged EXEC Mode Global Configuration Mode Interface Configuration Mode Interface ethernet Interface link aggregation Interface range ethernet Interface range link aggregation Interface vlan VLAN Configuration Mode The following table gives detailed information about the Accessing path Prompt of each mode and how to exit the current mode and access the next mode Accessing Logout or Access the next Mode Prompt Path mode Primary mode once it is Use the exit command to disconnect the connected with the switch except that the switch is User EXEC switch TP LINK gt connected through the Console port Mode Use the enable command to access Privileged EXEC mode Use the enable Use the exit command to disconnect the command to enter this switch except that the switch is mode from User EXEC connected through the Console port Privileged 4 or mene TP LIN Enter the disable command to return to EXEC Mode User EXEC mode Enter configure command to access Global Configuration mode Use the configure Use the exit or the end command or command to enter this press Ctrl Z to return to Privileged mode from Privileged EXEC mode Global ee mode A Use the interface type number Configuration TP LINK config i command to access interface Mode Configuration mode Use the vlan database to access VLAN Configuration mode TL SL3428 JetStream L2
60. LINK config dos prevent dos prevent type Description The dos prevent type command is used to select the DoS Defend Type To disable the corresponding Defend Type please use no dos prevent type command Syntax dos prevent type scan synfin xma scan null scan port less 1024 ping flood syn flood no dos prevent type scan synfin xma scan null scan port less 1024 ping flood syn flood 64 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Parameter scan synfin Scan SYNFIN attack xma scan Xma Scan attack null scan NULL Scan attack port less than 1024 t The SYN packets whose Source Port less than 1024 ping flood Ping flooding attack syn flood SYN SYN ACK flooding attack Command Mode Global Configuration Mode Example Enable two DoS Defend Types named Xma Scan attack and Ping flooding attack TP LINK config dos prevent xma scan ping flood show dos prevent Description The show dos prevent command is used to display the DoS information of the detected DoS attack including enable disable status the DoS Defend Type the count of the attack etc Syntax show dos prevent Command Mode Any Configuration Mode Example Display the DoS information of the detected DoS attack globally TP LINK config show dos prevent 65 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Chapter 13 IEEE 802
61. Managed Switch CLI Guide L2 Managed Switch CLI Guide Use the interface type Use the end command or press Ctrl Z number command to to return to Privileged EXEC mode Interface ans enter this mode from TP LINK config if Enter exit command to return to Global Configuration Global Configuration A Configuration mode Mode mode A port number must be specified in the interface command Use the vlan database Use the end command or press Ctrl Z VLAN command to enter this TP LINK config to return to Privileged EXEC mode Configuration Mode mode from Global vlan Enter the exit command to return to Configuration mode Global configuration mode Note 1 The user is automatically in User EXEC Mode after the connection between the PC and the switch is established by a console port or by a telnet connection 2 Each command mode has its own set of specific commands To configure some commands you should access the corresponding command mode firstly Global Configuration Mode In this mode global commands are provided such as the Spanning Tree Schedule Mode and so on e Interface Configuration Mode In this mode users can configure one or several ports different ports corresponds to different commands a Interface Ethernet Configure parameters for an Ethernet port such as Duplex mode flow control status b Interface range Ethernet The commands contained are the same as that of the
62. Mode Any Configuration Mode Example Display the configuration of DHCP Snooping globally TP LINK config show dhcp snooping global show dhcp snooping information Description The show dhcp snooping information command is used to display the Option 82 configuration of DHCP Snooping Syntax show dhcp snooping information Command Mode 57 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Any Configuration Mode Example Display the Option 82 configuration of DHCP Snooping TP LINK config show dhcp snooping information show dhcp snooping interface Description The show dhcp snooping interface command is used to display the interface configuration of DHCP Snooping Syntax show dhcp snooping interface ethernet port num Parameter port num The number of the switch port By default it will display the configuration of all the ports Command Mode Any Configuration Mode Example Display the interface configuration of all the ports TP LINK config show dhcp snooping interface 58 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Chapter 11 ARP Inspection Commands ARP Address Resolution Protocol Detect function is to protect the switch from the ARP cheating such as the Network Gateway Spoofing and Man In The Middle Attack etc arp detection global Description The arp detection global command is used to enable the ARP Detection f
63. NMP v3 User with none MD5 and SHA options None indicates no authentication method is used MD5 indicates the port authentication is performed via HMAC MD5 algorithm and SHA indicates the port authentication is performed via SHA Secure Hash Algorithm SHA authentication mode has a higher security than MD5 mode By default the Authentication Mode is none confirm pwd Authentication Password ranging from 1 to 16 characters emode The Privacy Mode of the SNMP v3 User with none and DES 170 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide options None indicates no privacy method is used and DES indicates DES encryption method is used By default the Privacy Mode is none encrypt pwd Privacy Password ranging from 1 to 16 characters Command Mode Global Configuration Mode Example Add User admin to Group group2 and configure the Security Model of the user as v3 the Security Level of the group as authPriv the Authentication Mode of the user as MD5 the Authentication Password as 11111 the Privacy Mode as DES and the Privacy Password as 22222 TP LINK config snmp user add admin local group2 smode v3 slev authPriv cmode MD5 cpwd 11111 emode DES epwd 22222 snmp community add Description The snmp community add command is used to add Community To delete the corresponding Community please use no snmp community add command SNMP v1 and SNMP v2c adopt community name authenti
64. NTDP Interval Time ranges from 1 to 60 in minutes By default it is 1 hop NTDP Hops which is the hop count the switch topology collects NTDP Hops ranges from 1 to 16 By default it is 3 hop delay NTDP Hop Delay which is the time between the switch receiving NTDP request packets and the switch forwarding NTDP request packets for the first time NTDP Hop Delay ranges from 1 to 1000 in milliseconds By default it is 200 port delay NTDP Port Delay which is the time between the port forwarding NTDP request packets and its adjacent port forwarding NTDP request packets over NTDP Port Delay ranges from 1 to 100 in milliseconds By default it is 20 Command Mode Global Configuration Mode Example Enable NTDP function globally and specify NTDP Interval Time as 20 minutes NTDP Hops as 5 NTDP Hop Delay as 300 milliseconds and NTDP Port Delay as 50 milliseconds 186 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide TP LINK config cluster ntdp status enable interval 20 hop 5 hop delay 300 port delay 50 cluster explore Description The cluster explore command is used to enable the topology information collecting function manually Syntax cluster explore Command Mode Global Configuration Mode Example Enable the topology information collecting function manually TP LINK config cluster explore cluster Description The cluster command is used to configure Cluster Por
65. Stream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide system time gmt time zone ntp server backup ntp server Parameter time zone Your local time zone and it ranges from 12 to 13 ntp server The IP Address for the Primary NTP Server Backup ntp server The IP Address for the Secondary NTP Server Command Mode Global Configuration Mode Example Configure the system time mode as gmt the time zone is 12 the primary ntp server is 133 100 9 2 and the secondary ntp server is 139 78 100 163 TP LINK config system time gmt 12 133 100 9 2 139 78 100 163 system time manual Description The system time manual command is used to configure the system time manually Syntax system time manual time Parameter time Set the date and time manually MM DD YYYY HH MM SS Command Mode Global Configuration Mode Example Configure the system mode as manual and the time is 12 20 2010 17 30 35 TP LINK config system time manual 12 20 2010 17 30 35 system time dst Description The system time dst command is used to configure the DST Daylight Saving Time To clear all the information please use no system time dst command Syntax system time dst sfart date start time end date end time 99 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide no system time dst Parameter start date The start date of DST you set start time The start tim
66. TP LINK CLI Reference Guide TL SL3428 JetStream L2 Managed Switch Rev 1 1 0 1910010622 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide COPYRIGHT amp TRADEMARKS Specifications are subject to change without notice TIP LINIK is a registered trademark of TP LINK TECHNOLOGIES CO LTD Other brands and product names are trademarks or registered trademarks of their respective holders No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation transformation or adaptation without permission from TP LINK TECHNOLOGIES CO LTD Copyright 2012 TP LINK TECHNOLOGIES CO LTD All rights reserved http www tp link com TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide CONTENTS PRETACeS seoa aa raa a aaa a a a E EAR 1 Chapter Using the CLI o conioscinasoniinadandant ee eed eneteees 4 TT Accessing the CE ence A ea A 4 1 121 Logon by a console POr atada 4 1 1 2 Logon by Teletirania 6 1 2 CLI Command Modes c cccccccceeceeccceceeeeeeeececeeeeaeeeeeeeeeeseeccaeeaeeeeeeessenccieaeeeteeeeseeeniaes 8 113 Security Levels tt e Geet 11 dido CONVENTIONS ia das 11 1 41 Format Conventions da a 11 14 2 Special Character uti dd ae 11 124 3 Parameter ForMatiursinaauadraiad o aaa aii an 12 Chapter 2 User Interface iii a 13 able AEE Ad 13 AE EEES OO 13 CISA iia ii tit bites 14
67. TP LINK config show interface link aggregation 36 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Chapter 8 LACP Commands LACP Link Aggregation Control Protocol is defined in IEEE802 3ad and enables the dynamic link aggregation and disaggregation by exchanging LACP packets with its partner The switch can dynamically group similarly configured ports into a single logical link which will highly extend the bandwidth and flexibly balance the load lacp system priority Description The lacp system priority command is used to set global lacp system priority Syntax Lacp system priority value Command Mode Global Configuration Mode Parameter value system priority ranging from 0 to 65535 By default the value is 32768 Example Set global lacp system priority 1024 TP LINK config lacp system priority 1024 lacp interface Description The lacp interface command is used to enable LACP protocol on the current port To disable LACP protocol please use no lacp command Syntax lacp no lacp Command Mode 37 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Interface Configuration Mode interface ethernet interface range ethernet Example Enable LACP protocol on the port 1 TP LINK config interface ethernet 1 TP LINK config if lacp lacp admin key Description The lacp admin key command is used to configure the admin key To resto
68. XX XX XX XX gt One or several values can be typed for a port list or a vlan list using comma to separate Use a hyphen to designate a range of values for instance 1 3 5 7 indicates choosing 1 3 4 5 and 7 12 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Chapter 2 User Interface enable Description The enable command is used to access Privileged EXEC Mode from User EXEC Mode Syntax enable Command Mode User EXEC Mode Example If you have set the password to access Privileged EXEC Mode from User EXEC Mode TP LINK gt enable Enter password TP LINK enable password Description The enable password command is used to set the password for users to access Privileged EXEC Mode from User EXEC Mode To return to the default configuration please use no enable password command Syntax enable password password no enable password Parameter password super password which contains 16 characters at most composing digits English letters and underdashes only By default it is empty Command Mode Global Configuration Mode Example Set the super password as admin to access Privileged EXEC Mode from User EXEC Mode TP LINK config enable password admin 13 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide disable Description The disable command is used to return to User EXEC Mode from Privileged EXEC Mode Syntax disable Command Mode P
69. a a aaa Aa adair eetan 57 show dhcp snooping information cccccceeeeeeeeeneeeeeeeeeeeeeneeaeeeeeeeeeeeeeceaeaeeeeeeeeteseenseaeeees 57 show dhcp snooping interface cceceeseceeceeeeeeeeenceeeeceeeeesecenaeeceeseeeeeeeceuaeeeeeeeeesstsnseeeees 58 Chapter 11 ARP Inspection COMMANdOS ooonnncccccccccconnnnnnnnnncnonenennnanannnnnnnnnnnnnnnannns 59 arp detection global risma licor eden p ad SM eraa nen aAA aaae 59 arp detectlon TUS EDO aitai iei aa ea seee aia on 59 arp detection interface cccccccceeeceeceeecneeeteeeeceeeeneaeeeeeeeeeeececceseaeeeseeeseaeqcaeaeeeeeeeesseesineneees 60 arp detection limite teca rie ocacion ida 60 arp detection MECOVEN iicicioin cti rd calada aida Dato 61 show arp detection global Aiie aa 62 show arp detection interface cccecceecscceceeeeeeeeeeeaeeeeeeeeeeeeenseaeaeeeeeeeeeeeceieaeeeeeeeesseesnneneeees 62 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Show arp detection statistic oooonocnccnnncnnnonnnonnnnnnnnnnnnonnonononononononnnonononnncnnncnnneninaninoss 63 show arp detection statistic reset onncnccccncnnnnonncnnnnnnnnonnnnnnnononnnnnonnnonnnnnnnnnnnnnnncnnncnnninnns 63 Chapter 12 DoS Defend Command ccccccccececeeeeeeeeeeeeeeeeeeeneeeeeeeeeeeeeeeeeaneees 64 AOS PEO VE el Set oe Atta A ease ee ea a ee ihe 64 COS PreveNnl PO a ick A a A AAA a AAA A Ai 64 SHOW dos prevent ia id haat Ren
70. aC HOY os senses Seah A oh A tinal Mente hes 142 SNOW ACh CONT G asses oases cia 142 SNOW ACh DING it A A A EAE aE 143 Chapter 24 MSTP Command ooooonncccccccccnnnncnnnncnnncncnnnonanannnnncnnnnnnnnnnnnannnnnnnnnnnnnnanns 144 spanning ree GlODAl cise teat A NA aa 144 spanning tree COMMON CONAIG cceececceeeeeeeeeceeeeeeeeeeeeeecdcaeeeeeeeeeeeeecensaeeeeeeeessecsuseneeeeees 145 SPanniNg te TEGION 4 amp as des le eae leet le ee ni ess 146 Spanning tree MSti cotss co Via dat A Rage hed Meneses 147 Spanning tree Mist acetate ates as a al ie Ath a a ais 148 Spanning tree Ti AA as 149 spanning tree security ooooconccooncconoconcnoncnonononenoneno nono nono nero nene none none none none none none none anna 149 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Spanning tree MCNECK cio cocina E a les 150 show spanning tree global iMfO oooononococicnncnnnccoconoocccnnccnnnnnnnnnnnnnonononnnnnnnncnnnnnnnnnnnnnnnnnnnnnno 151 show spanning tree global Config ooooocococcccocccoccoococcnoncccnonannonnnnnonononnnnnnnncnnnnnnnnnnnnnnnnnncnnnno 151 show spamning tree port CONfig ccccceeceeeeeeeeeeeeceeeeeeeceneaaeeeeeeeeeeseeceneaeeeeeeeeseeesnseeeeeees 151 SNOW spanning tree region occcccccccncnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnncnnncnninin 152 show spanning tree msti CONFIG cccccceceeeeeeeneeeceeeeeeeceeeeaeeeeeeeeeeseseaeaeeeeeeeesesesnsee
71. aging timer Aging Time which is the period for the neighbor switch to keep the NDP packets from this switch Aging Time ranges from 5 to 255 in seconds By default it is 180 hello timer Hello Time which is the interval to send NDP packets Hello Time ranges from 5 to 254 in seconds By default it is 60 Command Mode Global Configuration Mode Example Enable NDP function globally and configure Aging Time as 120 seconds Hello Time as 50 seconds TP LINK config cluster ndp status enable aging timer 120 hello timer 50 185 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide cluster ntdp Description The cluster ntdp command is used to configure NTDP globally To return to the default configuration please use no cluster ntdp command NTDP Neighbor Topology Discovery Protocol is used to collect the NDP information and neighboring connection information of each device in a specific network range It provides the commander switch with the information of devices which can join the cluster and collects topology information of devices within the specified hops Syntax cluster ntdp status disable enable interval interval hop hop hop delay hop delay port delay port delay no cluster ntdp Parameter status Enable Disable NTDP function globally By default it is disabled interval NTDP Interval Time which is the interval to collect topology information
72. al Country region Area code Phone number Connect using y Figure 1 3 Select the port to connect 5 Configure the port selected in the step above as the following figure 1 4 shown Configure Bits per second as 38400 Data bits as 8 Parity as None Stop bits as 1 Flow control as None and then click OK TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide COM1 Properties LL A X Port Settings Bits per second Data bits Parity Stop bits Flow control Figure 1 4 Port Settings 6 Type the User name and Password in the Hyper Terminal window the factory default value for both of them is admin The DOS prompt TP LINK gt will appear after pressing the Enter button as figure1 5 shown It indicates that you can use the CLI now tp link HyperTerminal Connected 0 00 32 Ako detect Ako detect Figure 1 5 Log in the Switch 1 1 2 Logon by Telnet To log on to the switch by a Telnet connection please take the following steps 1 Make sure the switch and the PC are in the same LAN 2 Click Start Run to open the Run window TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Internet l My Documents Internet Explorer Recent Documents gt H E mail ie My E Microsoft Office Outlook fe My Pickines a Notepad 2 My Music PE My Computer es Command Prompt oe e My Network Places Y Paint Y Control
73. alloc Description The ip dhcp alloc command is used to enable the DHCP Client function When this function is enabled the switch will obtain IP from DHCP Client server Syntax ip dhcp alloc Command Mode Global Configuration Mode Example Enable the DHCP Client function TP LINK config ip dhcp alloc ip bootp alloc Description The ip bootp alloc command is used to obtain IP address from BOOTP Server Syntax ip bootp alloc 101 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Command Mode Global Configuration Mode Example Enable the BOOTP Protocol to obtain IP address from BOOTP Server TP LINK config ip bootp alloc reset Description The reset command is used to reset the switch s software After resetting all configuration of the switch except the IP Address will restore to the factory defaults and your current settings will be lost Syntax reset Command Mode Privileged EXEC Mode Example Reset the software of the Switch TP LINK reset reboot Description The reboot command is used to reboot the Switch To avoid damage please don t turn off the device while rebooting Syntax reboot Command Mode Privileged EXEC Mode Example Reboot the Switch TP LINK reboot 102 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide user config backup Description The user config backup command is used to backup the confi
74. ameter Interface The port selected to display the connective status By default the connective status of all ports is displayed Command Mode Any Configuration Mode Example Display the connective status of all Ethernet ports TP LINK config show interface status ethernet show interface counters Description The show interface counters command is used to display the statistic information of an Ethernet port Syntax show interface counters ethernet interface Parameter Interface The port selected to display the statistic information By default the statistic information of all ports is displayed Command Mode 116 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Any Configuration Mode Example Display the statistic information of Ethernet port3 TP LINK config show interface counters ethernet 3 show storm control ethernet Description The show storm control ethernet command is used to display the storm control information of an Ethernet port Syntax show storm control ethernet port Parameter port The port number of the port selected to display the storm control information It ranges from 1 to 28 By default the storm control information of all ports is displayed Command Mode Any Configuration Mode Example Display the storm control information of all Ethernet ports TP LINK config show storm control ethernet show port rate limit
75. ary ip p addr no radius authentication secondary ip Parameter ip addr The IP address of the alternate authentication server By default it is 0 0 0 0 Command Mode Global Configuration Mode Example Configure the IP address of the alternate authentication server as 10 20 1 101 TP LINK config radius authentication secondary ip 10 20 1 101 radius authentication port Description The radius authentication port command is used to configure the authentication port of the alternate authentication server To restore to the default value please use no radius authentication port command Syntax radius authentication port port num no radius authentication port Parameter port num The UDP port of authentication server s raging from 1 to 65535 and the default port is 1812 Command Mode 73 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Global Configuration Mode Example Configure the authentication port of the alternate authentication server as 1815 TP LINK config radius authentication port 1815 radius authentication key Description The radius authentication key command is used to configure the shared password for the switch and the authentication servers to exchange messages To clear the radius authentication key please use no radius authentication key command Syntax radius authentication key key string no radius authentication key Parameter key string
76. asymmetrical encryption technology SSL uses key pair to encrypt decrypt information A key pair refers to a public key contained in the certificate and its corresponding private key By default the switch has a certificate self signed certificate and a corresponding private key The Certificate Key Download function enables the user to replace the default key pair ssl enable Description The ssl enable command is used to enable the SSL function on the switch To disable the SSL function please use no ssl enable command Only the SSL function is enabled a secure HTTPS connection can be established Syntax ssl enable no ssl enable Command Mode Global Configuration Mode Example Enable the SSL function TP LINK config ssl enable ssl download certificate Description The ssl download certificate command is used to download a certificate to the switch from TFTP server Syntax ssl download certificate ss cert ip address p addr Parameter ssi cert The name of the SSL certificate which is selected to download to the switch The length of the name ranges from 1 to 25 characters The 90 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Certificate must be BASE64 encoded ip addr The IP address of the TFTP server Command Mode Global Configuration Mode Example Download a SSL Certificate named ssl cert from TFTP server with the IP Address of 192 168 0 148 TP LIN
77. ation of the Local Log including the log buffer and the log file Syntax show logging local config Command Mode Any configuration Mode Example Display the configuration of the Local Log TP LINK config show logging local config show logging loghost Description The show logging loghost command is used to display the configuration of the log host Syntax show logging loghost index Parameter index The index of the log host whose configuration will be displayed Display the configuration of all the log hosts by default Command Mode Any Configuration Mode Example Display the configuration of the log host 2 TP LINK config show logging loghost 2 83 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide show logging buffer Description The show logging buffer level command is used to display the log information in the log buffer according to the severity level Syntax show logging buffer level eve Parameter level Severity level There are 8 severity levels marked with values 0 7 The information will be displayed only when the log with the same or smaller severity level value Display all the log information in the log buffer by default Command Mode Any Configuration Mode Example Display the log information from level O to level 5 in the log buffer TP LINK config show logging buffer level 5 show logging flash Description The show logging flash l
78. ation about how to use the CLI CLI Command Modes Security Levels and some Conventions Chapter 2 User Interface Provide information about the commands used to switch between five CLI Command Modes Chapter 3 IEEE 802 1Q VLAN Commands Provide information about the commands used for configuring IEEE 802 1Q VLAN Chapter 4 Protocol VLAN Commands Provide information about the commands used for configuring Protocol VLAN Chapter 5 Voice VLAN Commands Provide information about the commands used for configuring Voice VLAN Chapter 6 GVRP Commands Provide information about the commands used for configuring GVRP GARP VLAN registration protocol Chapter 7 LAG Commands Provide information about the commands used for configuring LAG Link Aggregation Group Chapter 8 LACP Commands Provide information about the commands used for configuring LACP Link Aggregation Control Protocol Chapter 9 User Manage Commands Provide information about the commands used for user management Chapter 10 Binding Table Commands Provide information about the commands used for binding the IP address MAC address VLAN and the connected Port number of the Host together Chapter 11 ARP Inspection Commands Provide information about the commands used for protecting the switch from the ARP cheating or ARP Attack TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Chapter 12 DoS Defend Command Provide information
79. cation The community name can limit access to the SNMP agent from SNMP network management station functioning as a password Syntax snmp community add name read only read write mib view no snmp community add name Parameter name Community Name ranging from 1 to 16 characters read only read write The access rights of the community with read only and read write options mib view The MIB View for the community to access Command Mode Global Configuration Mode Example Add Community community1 and the community has read write management right to View view1 171 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide TP LINK config snmp community add community1 read write view1 snmp notify add Description The snmp notify add command is used to add Notification To delete the corresponding Notification please use no snmp notify add command With the Notification function enabled the switch can initiatively report to the management station about the important events that occur on the Views which allows the management station to monitor and process the events in time Syntax snmp notify add ip udp port user name smode v1 v2c v3 slev noAuthNoPriv authNoPriv authPriv type trap inform resend resend timeout timeout no snmp notify add ip user name Parameter ip The IP Address of the management Host udp port
80. ch as RADIUS packets to be transmitted to the authentication server Command Mode Global Configuration Mode Example Configure the Authentication Method of IEEE 802 1X as pap TP LINK config dot1x auth method pap dot1x guest vlan Description The dot1x guest vlan command is used to enable the Guest VLAN function globally To disable the Guest VLAN function please use no dot1x guest vlan command Syntax dot1x guest vlan vid no dot1x guest vlan Parameter vid The VLAN ID needed to enable the Guest VLAN function ranging from 2 to 4094 The supplicants in the Guest VLAN can access the specified network source Command Mode Global Configuration Mode Example Enable the Guest VLAN function for VLAN 5 TP LINK config dot1x guest vlan 5 67 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide dot1x quiet period Description The dot1x quiet period command is used to enable the quiet period function To disable the function please use no dot1x quiet period command Syntax dot1x quiet period no dot1x quiet period Command Mode Global Configuration Mode Example Enable the quiet period function TP LINK config dot1x quiet period dot1x timer Description The dot1x timer command is used to configure the Quiet Period and the SupplicantTimeout To restore to the default please use no dot1x timer command Syntax dot1x timer quiet period period supp timeout timeout
81. command The User in a SNMP Group can manage the switch via the management station software The User and its Group have the same security level and access right Syntax snmp user add name local remote group name smode v1 v2c v3 slev noAuthNoPriv authNoPriv authPriv emode none MD5 SHA cpwd confirm pwa emode none DES epwd encrypt pwal no snmp user add name Parameter name User Name ranging from 1 to 16 characters local remote User Type with local and remote options Local indicates that the user is connected to a local SNMP engine while remote indicates that the user is connected to a remote SNMP engine group name The Group Name of the User The User is classified to the corresponding Group according to its Group Name Security Model and Security Level smode The Security Model of the User with v1 v2c and v3 options By default the option is v1 The Security Model of the User must be the same with that of the Group which the User belongs to slev The Security Level of SNMP v3 Group There are three options including noAuthNoPriv no authorization and no encryption authNoPriv authorization and no encryption and authPriv authorization and encryption By default the option is noAuthNoPriv The Security Level of the User must be the same with that of the Group which the User belongs to cmode The Authentication Mode of the S
82. configuration ranging from 1 to 12 You can only select one entry for each command By default the configuration of all entries is displayed Command Mode Any Configuration Mode Example Display the configuration of all Alarm Management entries TP LINK gt show snmp rmon alarm 184 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Chapter 27 Cluster Commands Cluster Management function enables a network administrator to manage the scattered devices in the network via a management device After a commander switch is configured management and maintenance operations intended for the member devices in a cluster is implemented by the commander device cluster ndp Description The cluster ndp command is used to configure NDP globally To return to the default configuration please use no cluster ndp command NDP Neighbor Discovery Protocol is used to discover the information of the directly connected neighbor devices to support cluster establishing An NDP enabled device sends NDP packets regularly to neighbor devices as well as receives NDP packets from neighbor devices An NDP packet carries the aging time which indicates the period of the receiving devices to keep the NDP packet Syntax cluster ndp status disable enable aging timer aging timer hello timer hello timer no cluster ndp Parameter status Enable Disable NDP function globally By default it is disabled
83. configures neke A A A A edhe E 14 Md A AA he ett ae aie ene 14 A 15 Chapter 3 IEEE 802 1Q VLAN Commands 0occccccccccnooncccncccccncncnnnananannnnnnnnnnnnnanans 16 Vian dd ui AA ds 16 NO 16 Interface VIAN icon e bir 17 CESCIPUON A aie a A A aN ee ies 17 SIIC POIS el SA Sita ak dA SR e de EO es OR o 18 switchport allowed vlan ccoo ad tia 18 SWITCHPOME PU di dro 19 switchport general egress TU E o o ooooccccnccnnncnnncnnnnoncnononononononononononnnonnnnnnnnnnnnnnnnnnnnnncnnneniness 19 SAOWVlAMiissiari da 20 show interface switchport cccccceccceceeee cece eeeeeeeeceneaeeeeeeeeesecensaaeeeeeeeeeeeeeneasaeeeeeeeesseesinineeees 20 Chapter 4 Protocol VLAN COMMANdS oooonnnnncccccccccnnnnonnnnnnnnnnnnennnanannnnnnnnnnnennnanans 21 protocol vian template lle e a anar 21 Protocolwlan vlase a a e lan 21 protocol vlan interface cccccceceeecceeceee cece ceeeeeeeceeeaeeeeeeeesesceaeaeeceeeeesesececeeeaeeseeeeesseeeneaeeeseeeess 22 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide show protocol vlan template cccccccccceeeeceeeceeeeeeeeeeeeeeeeeeeseeaeeeaeeeaeeeaeeeaaeeaeeeaeeeaeeeaaeeaaeeaes 23 show protocol Vlan VIAN cccccceecececeeeceeeeeeeeeeeeeeeeeeeeeeeneeeeeeaeeeaueeaaeeaaeeaeeeaaeeaaeeaeeeaeeeaaeeaaeeaes 23 show protocol vlan interface ccccccccceceeeeeeeeeeeaeeeeeeeeseeceeeaeeeeeeeesesececeaeaeeeeeeeseenenieaeeeseeeess 23 Chapter 5 Voice VLAN Commands ccc
84. cooonnnnnnncccccncnnnnnnnnnnnncncnnnnnnnnnnnnnnnennnnnnnnnannns 25 voice Vlan enables ici AA ni AAA As es ee ie 25 voice vlan aging tiMe i i ini lili linn nnn inn inn il iinet 25 VOICE VlAaNn OUl iia aii ai A Awe hee ae E 26 switchport voice vlan mode ooooococoncnoncconcnnncnononnnnnnnnnnonononononnnonnnnno nero nnnnnnnnnnnnnnnnnnnnnnnncnnnnnnness 27 show voice vlan global c eceeeeeeee cece cece eeeeaaeeaaeeaeeeaeeeaeee see aaeeaaee sues sues sees aaeeaaeeaaeeaaeeaaeeaaeeaes 27 SHOW VOICS V AN Uli ic ed eee eee 28 show VOICE VIAN SWILCNPOMt 00 cee cece eee cece eeeeaeee cane aeee cane cane sees aaeeaee sees sees sues sues aaeeaaeeaaeeaaeeaaeeaes 28 Chapter 6 GVRP GOmiman GS isssp css ssossccnztcacassscanssnnston cadens snnncnancasaasmscutansmneatecn sents 29 OVI 0 BEEPER E ate eel A Ae ae amen eee 29 gvr interface s 5 1s skid A Mitts ae Ne id eae NE aes aa el 29 gyrp registration ieri ae gd as es 30 Co AA TIAA E EE AEA Riad S A ee thd RCE one ATEA E 30 A A NL 31 Show Gvrp intentace AA A ange Gees 32 Chapter 7 LAG CommandS ssssscscchscsescctessaacassssansncessastenssnsasndesueasaassscussdanseatccnsces 33 interface link aggregation cceceeceeeecececeeeeeeeeeeeaeeeeeeeeeeeeeeeaeeeeeeeeeesececeeeaeeeeeesesensnieaeeeteeeess 33 interface range link aggregation ooooooocococnccnncocooococcncoconnnnnnnnnnnnnnnnnnonnnnnnnnnnnnnnoncnnnnnnnnnnnoninnns 33 HIFIK AGGFEG ALON ra A A i i agit dae ces 34 link aggregatio
85. d status disable enable pri priority mapped mapped no spanning tree msti msti id Parameter msti id Instance ID ranging from 1 to 8 status Enable Disable the corresponding instance By default it is disabled priority MSTI Priority which must be multiple of 4096 ranging from O to 61440 By default it is 32768 MSTI priority is an important criterion on determining if the switch will be chosen as the root bridge in the specific instance mapped VLAN Instance mapping Enter the VLAN ID which belongs to 147 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide the corresponding instance ID in the format of 1 2 4 Command Mode Global Configuration Mode Example Enable Instance 1 add VLAN 2 3 4 5 8 for it and configure MSTI Priority as 4096 TP LINK config spanning tree msti 1 status enable pri 4096 mapped 2 5 8 spanning tree msti Description The spanning tree msti command is used to configure MSTP Instance Port To return to the default configuration of the corresponding Instance Port please use no spanning tree msti command A port can play different roles in different spanning tree instance You can use this command to configure the parameters of the ports in different instance IDs as well as view status of the ports in the specified instance Syntax spanning tree msti id pri pri path path no spanning tree msti fa Parameter id
86. d Switch CLI Guide L2 Managed Switch CLI Guide Syntax show acl config acl id Parameter acl id The ID of the ACL selected to display the configuration Command Mode Any Configuration Mode Example Display the configuration of the MAC ACL whose ID is 20 TP LINK gt show acl config 20 show acl bind Description The show acl bind command is used to display the configuration of Policy bind Syntax show acl bind Command Mode Any Configuration Mode Example Display the configuration of Policy bind TP LINK gt show acl bind 143 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Chapter 24 MSTP Commands MSTP Multiple Spanning Tree Protocol compatible with both STP and RSTP and subject to IEEE 802 1s can disbranch a ring network STP is to block redundant links and backup links as well as optimize paths spanning tree global Description The spanning tree global command is used to configure STP globally To return to the default configuration please use no spanning tree global command Syntax spanning tree global status disable enable mode stp rstp mstp cist cist htime hello time mage max age delay forward delay hcount hold count mhop max hops no spanning tree global Parameter status Enable Disable STP function globally By default it is disabled mode STP Version There are three options including SRP Spanning Tree Protocol
87. d force no dot1x port control Parameter auto authorized force unauthorized force The Control Mode for the port Auto In this mode the port will normally work only after passing the 802 1X Authentication Authorized force In this mode the port can work normally without passing the 802 1X Authentication Unauthorized force In this mode the port is forbidden working for its fixed unauthorized status By default the Control Mode is auto Command Mode Interface Configuration Mode interface ethernet interface range ethernet Example Configure the Control Mode for port 1 as authorized force TP LINK config interface ethernet 1 TP LINK config if dot1x port control authorized force dot1x port method Description The dot1x port method command is used to configure the Control Type of IEEE 802 1X for the specified port To restore to the default configuration please use no dot1x port method command Syntax dot1x port method mac based port based no dot1x port method Parameter mac based port based The Control Type for the port Mac based Any client connected to the port should pass the 802 1X 71 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Authentication for access Port based All the clients connected to the port can access the network on the condition that any one of the clients has passed the 802 1X Authentication By default the Con
88. dates I Accessibility Im Games Startup gt Internet Explorer WwW mn e Outlook Express a Network Connections 9 Network Setup Wizard Entertainment I System Tools WD Address Book 3 Calculator io Internet Internet Explorer 2 E mail Microsoft Office Out E New Connection Wizard Pe Remote Desktop Connection Y Wireless Network Setup Wizard Remote Assistance GY Command Prompt b de Notepad windows Media Player T Notepad e CARA 3 Windows Messenger Y Paint a Windows Movie Maker Program Compatibility Wizard WF Activate Windows Y synchronize OvisLink Wireless Clie Utility MSN Windows Media Play E IxChariot E asmax I LogMeTT I Tera Term Im Microsoft Office Im Macrovision E TP LINK All Programs OvisLink Tour Windows XP 3 Windows Explorer A WordPad Paint W ao royo FY Figure 1 1 Open Hyper Terminal 3 The Connection Description Window will prompt as figure1 2 Enter a name into the Name field and click OK TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Connection Description Y New Connection Enter a name and choose an icon for the connection Name tp link Moses Figure 1 2 Connection Description 4 Select the port to connect in figure 1 3 and click OK Connect To DB tp link Enter details for the phone number that you want to di
89. e VLAN TP LINK config show voice vlan switchport 28 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Chapter6 GVRP Commands GVRP GARP VLAN registration protocol is an implementation of GARP generic attribute registration protocol GVRP allows the switch to automatically add or remove the VLANs via the dynamic VLAN registration information and propagate the local VLAN registration information to other switches without having to individually configure each VLAN gvrp Description The gvrp command is used to enable the GVRP function globally To disable the GVRP function please use no gvrp command Syntax gvrp no gvrp Command Mode Global Configuration Mode Example Enable the GVRP function globally TP LINK config gvrp gvrp interface Description The gvrp interface command is used to enable the GVRP function for the desired port To disable the GVRP function of this port please use no gvrp command The GVRP feature can only be enabled for the trunk type ports Syntax gvrp no gvrp Command Mode Interface Configuration Mode interface ethernet interface range ethernet 29 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Example Enable the GVRP function for ports 2 6 TP LINK config interface range ethernet 2 6 TP LINK config if gvrp gvrp registration Description The gvrp registration command is used to configure the
90. e conversion among Candidate Switch and Individual Switch is Candidate Switch lt gt Individual Switch Command Mode Global Configuration Mode Example Change the role of the current switch to Candidate Switch TP LINK config cluster manage role change candidate show cluster ndp global Description The show cluster ndp global command is used to display the global configuration of NDP Syntax show cluster ndp global Command Mode Any Configuration Mode Example Display the global configuration of NDP TP LINK gt show cluster ndp global 188 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide show cluster ndp port status Description The show cluster ndp port status command is used to display NDP configuration of the certain port Syntax show cluster ndp port status port Parameter port The port selected to display the configuration of NDP ranging from 1 to 28 By default the configuration of all ports is displayed Command Mode Any Configuration Mode Example Display the NDP configuration of port 2 TP LINK gt show cluster ndp port status 2 show cluster neighbour Description The show cluster neighbour command is used to display the cluster neighbor information Syntax show cluster neighbour Command Mode Any Configuration Mode Example Display the cluster neighbor information TP LINK gt show cluster neighbour show cluster ntdp global Descriptio
91. e of DST you set end date The end date of DST you set end time The end time of DST you set Command Mode Global Configuration Mode Example Configure the dst dst is from April 1 00 00 to November 1 23 00 TP LINK config system time dst 04 01 0 11 01 23 ip address Description The ip address command is used to configure the IP Address Subnet Mask and Default Gateway To restore to the factory defaults please use no ip address command Syntax ip address ip addr ip mask gateway no ip address Parameter ip addr The system IP of the Switch The default system IP is 192 168 0 1 ip mask The Subnet Mask of the Switch The default Subnet Mask is 255 255 255 0 gateway The Default Gateway of the Switch By default it is empty Command Mode Global Configuration Mode Example Configure the system 255 255 255 0 TP LINK config ip address 192 168 0 69 255 255 255 0 IP as 192 168 0 69 and the Subnet Mask as 100 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide ip management vlan Description The ip management vlan command is used to configure the IP management VLAN through which you can log on to the switch Syntax ip management vlan v an id Parameter vlan id VLAN ID ranging from 1 to 4094 Command Mode Global Configuration Mode Example Set the VLAN6 as IP management VLAN TP LINK config ip management vlan 6 ip dhcp
92. e the level and the status of the log file input To restore to the default configuration please use no logging local flash command The log file indicates the flash sector for saving system log The information in the log file will not be lost after the switch is restarted and can be got by the show logging flash command Syntax logging local flash eve disable enable no logging local flash Parameter level Severity level of the log information output to each channel There are 8 severity levels marked with values 0 7 The smaller value has the higher priority Only the log with the same or smaller severity level value will be output By default it is 4 indicating that the log information marked with 0 4 will be saved in the log buffer disable enable Disable or enable the log file By default it is enabled Command Mode Global Configuration Mode Example Enable the log file function and set the severity as 7 TP LINK config logging local flash 7 logging clear Description The logging clear command is used to clear the information in the log buffer and log file Syntax logging clear buffer flash Parameter 81 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide buffer flash The output channels buffer and flash Clear the information of the two channels by default Command Mode Global Configuration Mode Example Clear the information in the log fi
93. ed on the CoS value of the ingress port and the mapping relation between the CoS and TC in IEEE 802 1P Example Configure the priority of port 5 as 3 TP LINK config interface ethernet 5 TP LINK config if qos 3 qos dot1p enable Description The qos dotip enable command is used to enable the mapping relation between IEEE 802 1P Priority and Egress Queue To disable the mapping relation please use no qos dot1p enable command 119 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Syntax qos dot1p enable no qos dot1p enable Command Mode Global Configuration Mode Example Enable the mapping relation between IEEE 802 1P Priority and Egress Queue TP LINK config qos dot1p enable qos dot1p config Description The qos dot1p config command is used to configure the mapping relation between IEEE 802 1P Priority and Egress Queue To return to the default configuration please use no qos dot1p config command IEEE 802 1P gives the Pri field in IEEE 802 1Q tag a recommended definition This field is used to divide packets into 8 priorities When IEEE 802 1P Priority is enabled the packets with IEEE 802 1Q tag are mapped to different priority levels based on IEEE 802 1P priority mode The untagged packets are mapped based on port priority mode Syntax qos dot1p config tag tc ic no qos dot1p config Parameter tag The 8 priority levels defined by IEEE 802 1P ranging from 0 to 7
94. ee eA Saeed eet 65 Chapter 13 IEEE 802 1X Commands ccoooonnnnnnnccccccncnonanannnnncncnnnnnnnanannnnnennnnnnnnnannns 66 CLOUT ie sascha a te Na ac Gres ale 66 dot x auth methode i2 0 sais ati ee ae A A Ai 66 dottx quest Vlanwis anniek AAA AA A al ee nil AAA 67 dotl x quiet perOd it AAA ee 68 DOMAIN A E i le ee a 68 CLOUT al Na Pes el Bi aca dd ee eat bd den nd dares roe ao Salen ds Ma evel Di ecg diverge ia 69 CLOUT sascha aa ed le eles ed E E ea cas oi te cit ales ole ta 69 dot lx quest Vlan AA bang es AA 70 dott port controls sfc Aa A Ah a athe oak AAA 70 AOL port method 2 2hisv Meee ata ee a el 71 radius authentication primary ip ococccccccccncccnnnnnnonnnnnnnonnnnnnnnnnnnnnnonononnnnnnnnnnnnnnnnnnnnnnnnnnncnnnnnnss 72 radius authentication secondary ip ccccceeceeceeeceeeeeeeeeeeeeeeeeeeeeeeseeeseeeaeeaueeaeeeaeeeaeeeaeeeaaeeaes 73 FACIUS AULNSNTICATION POTE sr sate ccacesacveddfuthawdecacgbe accu be edeeoes iz a aaae a A E i aeaaeai 73 radius authentication key occccccnnccnnnnnnnonnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnonnnnnnnonnnonnnnnnncnnnannncnnncnnnnss 74 radius accounting enable cconcccnnnnnncnnnonononononnnonnnnnnnnnnnnnnnonnnonnnonononnnennnonnncnnncnnnenineniness 74 FACIUS ACCOUNTING PMA elder 75 radius accounting SECONCALY iP ccecceceeeceeeceeeeeeeeeeeeeeeceeeeeeeseeeseeaeeeaeeeaeeeaaeeaeeeaeeeaeeeaaeeaes 75 FACIUS ACCOUNTING DOM a cs oe rada ia dardo 76 FACIUS ACCOUNTING KEY i fe
95. eeeees 152 show spanning tree msti port occcccccncnnnccnncnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnncnnncnnncnnn 153 show spanning tree security tc defend oooococonnccccoccccncccocncononnnononnnnoncnnnnncncnnnnconannnnnnnncnnono 153 show spanning tree security portdefend ooooononococicnnccccnnonononccnncccnnnnnnnnnnnnnnnoninnannnnnnnnanenens 154 Chapter 25 IGMP GOMIMANGS i ssscaaicessececceccsececctaceccceccuecesesciececscctececssciecnsetateceasiecs 155 IOMP SNOOPING global iz risa pte 155 IGMP SNOOPING CONG rs ceva deel le Lah anette cas 155 igmp snooping vlan config add c cccecceeeeeeeeeeeeeeeeeeeeeecensaaeeeeeeeesesenceaeaeeeeeeeeseeesnsieeeeees 156 igmp snooping VIAN CONFIG ccc ceeeeee cece ceeeeeeeceneaeeeeeeeeeeeceeeaaeeeeeeeeeeseeseaeaeeeeeeeesesesicuneeeeees 157 igmp snooping Multi Vlan CONTIO ooooooococcccnnocnconcancoccnnncononnnanonnnnnonononnannnnnnnnnnnnnnnnnnnnnncnnnnos 158 igmp snooping Static entry Add ooocccccccnnncccnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnonnnnninenicin 159 igmp snooping filter Add 2 2 eee eee eeee cece cece eeeeeeeaeeeeeeeeeeceneaaeaeeeeeeeeseneeaeaeeeeeeeesesesisueeeeees 160 igmp snooping filter config 0 0 2 2 ccc cece eeeeccce cece eeeeeene cece eeeeeeeeceneaaeeeeeeeeeeseeceaeaeeeeeeeeteeesuseneeeeees 160 IGMP SNOOPING filtere eee aa E Ee A de aes 161 show igmp snooping global config coooocoooccccnnccccncononocccnncnnoncnnnnnno
96. em Description Device Name Device Location System Contact Hardware Version Firmware Version System Time Run Time and so on 106 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Syntax show system info Command Mode Any Configuration Mode Example Display the system information TP LINK show system info show ip address Description The show ip address command is used to display MAC Address IP Address Subnet Mask and Default Gateway of the system whether the DHCP Client function is enabled or not and some other information Syntax show ip address Command Mode Any Configuration Mode Example Display the IP Address of the system TP LINK show ip address show system time Description The show system time command is used to display the time information of the switch Syntax show system time Command Mode Any Configuration Mode Example Display the time information of the switch TP LINK show system time 107 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide show system time dst Description The show system time dst command is used to display the DST time information of the switch Syntax show system time dst Command Mode Any Configuration Mode Example Display the DST time information of the switch TP LINK show system time dst show system time source Description The show system time source command is used to d
97. ennonannnnnnnnnnennanannnnnnes 173 A EP krieti a a aaa a a Aaa AEA ERA OAA E AEAEE 174 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide snmp rmon history enable occccccccnnccnnnonnnonononononononnnonnnnnnonononnnonnnnnnnonnnennnennnennnennnenans 174 SNMp MON EVENtUSE wae eek Ace A I eee ea a 175 SnMp rmon event description lic lidad dada 176 SAIMpP lMON EVENE LY Pe irc a 176 SNMP rMON EVENT OWNET cece cece cece eee tenet tree eee eee ener ee eeee n nn nn nn sees ARARE AREEN 177 snmp rmon event enable ococcccccnnconnnonononnnonnnonononononnnnnnnnonononononnnnnnnnnnnnnennnennnennnenenenans 177 snmp rmon alarm CONMIG ccccceeceeeeeeeeeeceeeeeeeceeeaeeeeeeeeeeceeceeeaeeeeeeeeseeeeaeaeeeeeeeeteeesnseeeeeees 178 snmp rmon alarm OWNTcocccocococococononcnnncnnncnnncnnncnnncnnnnnnncnnncnnonnnn nn nn nn nn nnnnnnnnnnnrnnnonnnonnnnnnnnnnnns 179 SAMP TMOR Aladino ed a a ae aces 180 Show snmp global Config ierosin aieeaa ane aN AEA a CAEN EEEE KAAL Ea AAE iA 180 SHOW SAMP VIEW nei aas Aa adeeb PE Sa sadeaususbeamncaedaeett 181 SHOW SNMP giou pii eaen a AEA A EE E aAa EE anA 181 SNOW SAMP USEF kinoa a eo e a E aaa aE EA tides Sl 182 SHOW SNMP COMMUNItY 0 ee ee eee ee eee 182 show snmp destinatiOn DOSt o oooccccccncnnnncnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnonnnonaceninin 182 SNOW SNMP rMON NISTON einai neee aea naa eea a EAEE REO AEE AAEE EEEE DEEDEE EEA 183 S
98. ess mask is 11 11 11 11 11 00 VLAN ID is 2 the user priority is 5 the time range for the rule to take effect is tSeg1 and the packets match this rule will be forwarded by the switch TP LINK config acl create 20 TP LINK config acl rule mac acl 20 10 op permit smac 00 01 3F 48 16 23 smask 11 11 11 11 11 00 vid 2 pri 5 tseg tSeg1 acl edit rule mac acl Description The acl edit rule mac acl command is used to edit MAC ACL rule Syntax acl edit rule mac acl acl id rule id op discard permit smac source mac smask source mac mask dmac destination mac dmask destination mac mask vid vlan id type Ethernet type pri user pri tseg time segment index idx Parameter acl id The desired MAC ACL for configuration rule id The rule ID op The operation for the switch to process packets which match the rules There are two options discard and permit Discard means discarding packets and permit means forwarding packets By default the option is permit 135 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide source mac The source MAC address contained in the rule source mac mask The source MAC address mask It is required if you typed the source MAC address destination mac The destination MAC address contained in the rule destination mac mask The destination MAC address mask It is required if you typed the destination
99. ether manually You can manually bind the IP address MAC address VLAN ID and the Port number together in the condition that you have got the related information of the Hosts in the LAN Syntax binding table user bind hostname ip addr mac addr vlan vid port port num none arp detection ip source guard both Parameter hostname The Host Name which contains 20 characters at most ip addr The IP Address of the Host mac addr The MAC Address of the Host vid The VLAN ID needed to be bound ranging from 1 to 4094 port num The number of port connected to the Host none arp detection ip source guard both The protect type for the entry arp detection indicates ARP detection ip source guard indicates IP filter none indicates applying none both indicates applying both Command Mode Global Configuration Mode Example Bind an ACL entry with the IP is 192 168 0 1 MAC is 00 00 00 00 00 01 VLAN ID is 2 and the Port number is 5 manually And then enable the entry for the ARP detection and IP filter function TP LINK config binding table user bind host1 192 168 0 1 00 00 00 00 00 01 vian 2 port 5 both 49 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide binding table remove Description The binding table remove command is used to delete the IP MAC VID PORT entry from the binding table Syntax binding table remove index dx Parameter id
100. evel command is used to display the log information in the log file according to the severity level Syntax show logging flash level evel Parameter level Severity level There are 8 severity levels marked with values 0 7 The information will be displayed only when the log with the same or smaller severity level value Display all the log information in the log file by default Command Mode Any Configuration Mode Example 84 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Display the log information with the level marked 0 3 in the log file TP LINK config show logging flash level 3 85 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Chapter 15 SSH Commands SSH Security Shell can provide the unsecured remote management with security and powerful authentication to ensure the security of the management information ssh server enable Description The ssh server enable command is used to enable SSH function To disable the SSH function please use no ssh server enable command Syntax ssh server enable no ssh server enable Command Mode Global Configuration Mode Example Enable the SSH function TP LINK config ssh server enable ssh version Description The ssh version command is used to enable the SSH protocol version To disable the protocol version please use no ssh version command Syntax ssh version v1 v2 no ssh ve
101. face Command Mode 23 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Any Configuration Mode Example Display the configuration of the protocol vlan interface TP LINK config show protocol vlan interface 24 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Chapter5 Voice VLAN Commands Voice VLANs are configured specially for voice data stream By configuring Voice VLANs and adding the ports with voice devices attached to voice VLANs you can perform QoS related configuration for voice data ensuring the transmission priority of voice data stream and voice quality voice vlan enable Description The voice vlan enable command is used to enable Voice VLAN function To disable Voice VLAN function please use no voice vlan enable command Syntax voice vlan enable vian id no voice vlan enable Parameter vlan id VLAN ID ranging from 2 to 4094 Command Mode Global Configuration Mode Example Enable the Voice VLAN function for VLAN 2 TP LINK config voice vlan enable 2 voice vlan aging time Description The voice vlan aging time command is used to set the aging time for a voice VLAN To restore to the default aging time for the Voice VLAN please use no voice vlan aging time command Syntax voice vlan aging time aging time no voice vlan aging time 25 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Pa
102. g status enable pri 64 expath 100 inpath 100 edge enable spanning tree region Description The spanning tree region command is used to configure the region of MSTP A switched network can be divided into many MST regions Multiple Spanning Tree Regions An MST region comprises multiple switches which have the same region configuration including region name and region revision configuration and the same VLAN to spanning tree mapping configuration 146 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Syntax spanning tree region name revision Parameter name The region name used to identify MST region It ranges from 1 to 32 characters revision The revision for MST region identification ranging from O to 65535 Command Mode Global Configuration Mode Example Configure the region name of MSTP as r1 and the revision level as 100 TP LINK config spanning tree region r1 100 spanning tree msti Description The spanning tree msti command is used to configure MSTP Instance To return to the default configuration of the corresponding Instance please use no spanning tree msti command Instance Configuration a property of MST region is used to describe the VLAN to spanning tree mapping configuration You can assign VLAN to different instances appropriate to your needs Every instance is a VLAN group independent of other instances and CST Syntax spanning tree msti msti
103. global config Command Mode Any Configuration Mode Example Display SNMP configuration globally TP LINK gt show snmp global config show snmp view Description The show snmp view command is used to display the View table Syntax show snmp view Command Mode Any Configuration Mode Example Display the View table TP LINK gt show snmp view show snmp group Description The show snmp group command is used to display the Group table Syntax show snmp group Command Mode Any Configuration Mode Example Display the Group table TP LINK gt show snmp group 181 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide show snmp user Description The show snmp user command is used to display the User table Syntax show snmp user Command Mode Any Configuration Mode Example Display the User table TP LINK gt show snmp user show snmp community Description The show snmp community command is used to display the Community table Syntax show snmp community Command Mode Any Configuration Mode Example Display the Community table TP LINK gt show snmp community show snmp destination host Description The show snmp destination host command is used to display the Notification table Syntax show snmp destination host Command Mode Any Configuration Mode Example 182 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Display the Notification tab
104. guration file by TFTP server Syntax user config backup filename name ip address p addr Parameter name Specify the name for the configuration file which would be backuped ip addr IP Address of the TFTP server Command Mode Privileged EXEC Mode Example Backup the configuration files by TFTP server with the IP 192 168 0 148 and name this file config cfg TP LINK user config backup filename config cfg ip address 192 168 0 148 user config load Description The user config load command is used to download the configuration file to the switch by TFTP server Syntax user config load filename name ip address p addr Parameter name Specify the name for the configuration file which would be downloaded ip addr IP Address of the TFTP server Command Mode Privileged EXEC Mode Example Download the configuration file to the switch by TFTP server with the IP 103 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide 192 168 0 148 and name this file config cfg TP LINK user config load filename config cfg ip address 192 168 0 148 user config save Description The user config save command is used to save current settings Syntax user config save Command Mode Privileged EXEC Mode Example Save current settings TP LINK user config save firmware upgrade Description The firmware upgrade command is used to upgrade the switch system via the TFTP serve
105. half duplex 100f 100Mbps full duplex 1000f 1000Mbps full duplex Command Mode Interface Configuration Mode interface ethernet interface range ethernet Example Configure the Negotiation Mode as 100Mbps full duplex for Ethernet port5 TP LINK config interface ethernet 5 TP LINK config if negotiation 100f storm control Description The storm control command is used to configure the Storm Control function To disable the Storm Control function please use no storm control command Storm Control function allows the switch to filter broadcast multicast and UL frame in the network If the transmission rate of the three kind packets exceeds the set bandwidth the packets will be automatically discarded to avoid network broadcast storm Syntax storm control bc status bc status mc status mc status ul status ul status rate rate no storm control Parameter bc status Enable Disable broadcast control feature for the port By default it is disabled mc status Enable Disable multicast control feature for the port By default it is disabled ul status Enable Disable UL Frame control feature for the port By default it is disabled rate The maximum ingress rate of the specified packets The packet traffic 113 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide exceeding the bandwidth will be discarded The value of it can be 128k 256k 512k or 1m 2m
106. he ACL Access Control List Chapter 24 MSTP Commands Provide information about the commands used for configuring the MSTP Multiple Spanning Tree Protocol Chapter 25 IGMP Commands Provide information about the commands used for configuring the IGMP Snooping Internet Group Management Protocol Snooping TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Chapter 26 SNMP Commands Provide information about the commands used for configuring the SNMP Simple Network Management Protocol functions Chapter 27 Cluster Commands Provide information about the commands used for configuring the Cluster Management function TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Chapter 1 Using the CLI 1 1 Accessing the CLI You can log on to the switch and access the CLI by the following two methods 1 Log on to the switch by the console port on the switch 2 Logon to the switch remotely by a Telnet or SSH connection through an Ethernet port 1 1 1 Logon by a console port To log on to the switch by the console port on the switch please take the following steps 1 Connect the PCs or Terminals to the console port on the switch by a provided cable 2 Click Start All Programs gt Accessories Communications Hyper Terminal to open the Hyper Terminal as the figure 1 1 shown Set Program Access and Defaults W Windows Catalog Windows Update E Program Up
107. he configuration information of all the Ethernet ports TP LINK config show lacp interface show lacp system priority Description The show lacp system priority command is used to display the global system priority value of LACP 39 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Syntax show lacp system priority Command Mode Any Configuration Mode Example Display the global system priority value of LACP TP LINK config show lacp system priority 40 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Chapter9 User Manage Commands User Manage Commands are used to configure the user name and password for users to log on to the Web management page with a certain access level so as to protect the settings of the switch from being randomly changed user add Description The user add command is used to add a new user Syntax user add user name password password confirm password confirm password guest admin disable enable Parameter user name Type a name for users login which contains 16 characters at most composing digits English letters and underdashes only password Type a password for users login which contains 16 characters at most composing digits English letters and underdashes only confirm password Type the password again guest admin Access level Guest only can view the settings without the rig
108. he show spanning tree global config command is used to display the global configuration of Spanning Tree Syntax show spanning tree global config Command Mode Any Configuration Mode Example Display the global configuration of Spanning Tree TP LINK show spanning tree global config show spanning tree port config Description The show spanning tree port config command is used to display the Port configuration of Spanning Tree Syntax show spanning tree port config port Parameter 151 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide port The port selected to display the configuration ranging from 1 to 28 By default the configuration of all ports is displayed Command Mode Any Configuration Mode Example Display the configuration of port 5 TP LINK config show spanning tree port config 5 show spanning tree region Description The show spanning tree region command is used to display the Region configuration of MSTP Syntax show spanning tree region Command Mode Any Configuration Mode Example Display the region configuration of MSTP TP LINK config show spanning tree region show spanning tree msti config Description The show spanning tree msti config command is used to display the Instance configuration of Spanning Tree Syntax show spanning tree msti config ia Parameter id The ID of the instance selected to display the configuration
109. ht to edit and modify Admin can edit modify and view all the settings of different functions disable enable Enable disable the user Command Mode Global Configuration Mode Example Add and enable a new admin user named tplink and of which the password is password TP LINK config user add tplink password password confirm password password admin enable 41 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide user remove Description The user remove command is used to delete an existing user The current user can t be deleted by itself Syntax user remove user name Parameter user name An existing user name Command Mode Global Configuration Mode Example Delete the user named tplink TP LINK config user remove tplink user modify status Description The user modify status command is used to modify the status of the existing user The current user can t be modified by itself Syntax user modify status user name disable enable Parameter user name The existing user name disable enable Disable enable the user Command Mode Global Configuration Mode Example Enable the status of user tplink TP LINK config user modify status tplink enable 42 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide user modify type Description The user modify type command is used to modify the access level for the ex
110. ime Leave Time which is the interval between the switch receiving a leave message from a host and the switch removing the host from the multicast groups Leave Time ranges from 1 to 30 in seconds By default it is 1 router port Static Router Port which is mainly used in the network with stable topology It ranges from 1 to 28 Command Mode Global Configuration Mode Example Enable Multicast VLAN and configure Router Port Time as 300 seconds Member Port Time as 200 seconds and Leave time as 15 seconds for VLAN 2 TP LINK config igmp snooping multi vlan config enable 2 rtime 300 mtime 200 Itime 15 igmp snooping static entry add Description The igmp snooping static entry add command is used to create static multicast IP entry To delete the corresponding entry please use no igmp snooping static entry add command The multicast groups configured here are not learned by IGMP Snooping and independent of dynamic multicast groups and multicast filter Multicast IP addresses ranges from 224 0 0 0 to 239 255 255 255 The range for receivers to join is from 224 0 1 0 to 239 255 255 255 Syntax Igmp snooping static entry add ip vian id switch port no igmp snooping static entry add ip vian id Parameter ip The static multicast IP address vian id The VLAN ID of the multicast IP ranging from 1 to 4094 switch port The forward port of the multicast group in the format of 1 3 6 23 159 T
111. ion status and diagnose malfunction logging local buffer Description The logging local buffer command is used to configure the severity level and the status of the configuration input to the log buffer To restore to the default configuration please use no logging local buffer command Local Log is the log information saved in the switch It has two output channels that is it can be saved to two different positions log buffer and log file Indicates the RAM for saving system log and the information in the log buffer can be got by show logging buffer command It will be lost when the switch is restarted Syntax logging local buffer eve disable enable no logging local buffer Parameter level Severity level of the log information output to each channel There are 8 severity levels marked with values 0 7 The smaller value has the higher priority Only the log with the same or smaller severity level value will be output By default it is 7 indicating that all the log information will be saved in the log buffer disable enable Disable or enable the log buffer By default it is enabled Command Mode Global Configuration Mode Example Enable the log buffer function and set the severity as 6 TP LINK config logging local buffer 6 enable 80 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide logging local flash Description The logging local flash command is used to configur
112. isplay the source of current time of the switch Syntax show system time source Command Mode Any Configuration Mode Example Display the source of current time of the switch TP LINK show system time source show system time mode Description The show system time mode command is used to display the configured mode for the switch to get system time Syntax show system time mode Command Mode 108 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Any Configuration Mode Example Display the configured mode for the switch to get system time TP LINK show system time mode 109 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Chapter 19 Ethernet Configuration Commands Ethernet Configuration Commands can be used to configure the Bandwidth Control Negotiation Mode and Storm Control for Ethernet ports interface ethernet Description The interface ethernet command is used to enter the Interface Configuration Mode and configure one Ethernet port Syntax interface ethernet interface Parameter interface The Ethernet port to be configured Command Mode Global Configuration Mode Example Enter the Interface Configuration Mode and configure Ethernet port2 TP LINK config interface ethernet 2 interface range ethernet Description The interface range ethernet command is used to enter the Interface Configuration Mode and configure mul
113. isting user The current user can t be modified by itself Syntax user modify type user name guest admin Parameter user name The existing user name guest admin Access level Guest limited user admin manager Command Mode Global Configuration Mode Example Change the access level of tplink to admin TP LINK config user modify type tplink admin user modify password Description The user modify password command is used to modify the password for the existing user Syntax user modify password user name old password new password confirm password Parameter user name The existing user name old password The old password new password The new password which contains 16 characters at most composing digits English letters and underdashes only confirm password Type the new password again Command Mode 43 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Global Configuration Mode Example Modify the password of tplink as newpwd TP LINK config user modify password tplink password newpwd newpwd user access control disable Description The user access control disable command is used to cancel the user access control Syntax user access control disable Command Mode Global Configuration Mode Example Cancel the user access control TP LINK config user access control disable user access control ip based Descrip
114. le TP LINK config logging clear buffer logging loghost Description The logging loghost command is used to configure the Log Host To clear the configuration of the specified Log Host please use no logging loghost command Log Host is to receive the system log from other devices You can remotely monitor the settings and operation status of other devices through the log host Syntax logging loghost index idx host ip level disable enable no logging loghost index idx Parameter idx The index of the log host The switch supports 4 log hosts host ip The IP for the log host level The severity level of the log information sent to each log host There are 8 severity levels marked with values 0 7 The smaller value has the higher priority Only the log with the same or smaller severity level value will be sent to the corresponding log host By default it is 6 indicating that the log information marked with 0 6 will be sent to the log host disable enable Disable or enable the log host By default it is disabled Command Mode Global Configuration Mode Example Enable the log host 2 and set the IP address 192 168 0 148 the level 5 82 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide TP LINK config logging loghost index 2 192 168 0 148 5 enable show logging local config Description The show logging local config command is used to display the configur
115. le TP LINK gt show snmp destination host show snmp rmon history Description The show snmp rmon history command is used to display the configuration of the history sample entry Syntax show snmp rmon history index Parameter index The index number of the entry selected to display the configuration ranging from 1 to 12 You can only select one entry for each command By default the configuration of all entries is displayed Command Mode Any Configuration Mode Example Display the configuration of all history sample entries TP LINK gt show snmp rmon history show snmp rmon event Description The show snmp rmon event command is used to display the configuration of SNMP RMON Event Syntax show snmp rmon event index Parameter index The index number of the entry selected to display the configuration ranging from 1 to 12 You can only select one entry for each command By default the configuration of all entries is displayed Command Mode Any Configuration Mode Example 183 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Display the Event configuration of entry 2 TP LINK gt show snmp rmon event 2 show snmp rmon alarm Description The show snmp rmon alarm command is used to display the configuration of the Alarm Management entry Syntax show snmp rmon alarm index Parameter index The index number of the entry selected to display the
116. lly TP LINK config show dot1x global show dot1x interface Description The show dot1x interface command is used to display the port configuration of 801 X Syntax show dot1x interface ethernet port num Parameter port num The number of the Ethernet port ranging from 1 to 28 Display the configuration of all the ports by default Command Mode Any configuration Mode 78 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Example Display the port configuration of 801 X TP LINK config show dot1x interface show radius authentication Description The show radius authentication command is used to display the configuration of the RADIUS authentication server Syntax show radius authentication Command Mode Any configuration Mode Example Display the configuration of the RADIUS authentication server TP LINK config show radius authentication show radius accounting Description The show radius accounting command is used to display the configuration of the accounting server Syntax show radius accounting Command Mode Any configuration Mode Example Display the configuration of the accounting server TP LINK config show radius accounting 79 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Chapter 14 Log Commands The log information will record the settings and operation of the switch respectively for you to monitor operat
117. meter port The port number you want to show its forward portlist Command Mode 129 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Any Configuration Mode Example Display the forward list of port 6 TP LINK show port isolation 6 130 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Chapter 23 ACL Commands ACL Access Control List is used to filter data packets by configuring a series of match conditions operations and time ranges It provides a flexible and secured access control policy and facilitates you to control the network security acl time segment Description The acl time segment command is used to add Time Range To delete the corresponding Time Range please use no acl time segment command A time range based ACL enables you to implement ACL control over packets by differentiating the time ranges A time range can be specified in each rule in an ACL The rule takes effect only when the specified time range is configured and the system time is within the time range Syntax acl time segment name start time start time end time end time week day week day start date start date end date end date holiday disable enable no acl time segment name Parameter name The Time Range name ranging from 1 to 16 characters start time The start time of the time slice in the format of HH MM By default it is 00 00
118. n The show cluster ntdp global command is used to display the global configuration of NTDP 189 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Syntax show cluster ntdp global Command Mode Any Configuration Mode Example Display the global configuration of NTDP TP LINK gt show cluster ntdp global show cluster ntdp port status Description The show cluster ntdp port status command is used to display NTDP configuration of the certain port Syntax show cluster ntdp port status port Parameter port The port selected to display the configuration of NTDP ranging from 1 to 28 By default the configuration of all ports is displayed Command Mode Any Configuration Mode Example Display the NTDP configuration of port 2 TP LINK gt show cluster ntdp port status 2 show cluster ntdp device Description The show cluster ntdp device command is used to display the device table of NTDP Syntax show cluster ntdp device Command Mode Any Configuration Mode Example 190 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Display the device table of NTDP TP LINK gt show cluster ntdp device show cluster manage role Description The show cluster manage role command is used to display the role of the current switch Syntax show cluster manage role Command Mode Global Configuration Mode Example Display the role of the current
119. n hash algorithM cccccecceeceeceeeeeeeeeeeeeeeeeeeaeeeeeeeaeeeseeaeeeaeeeaeeeaeeeaeeeaaeeaaeeaes 35 ASSCAPION aiid ee A A 35 show interface link aggregation oooniconococccnnniccnnnnoccnnonnnccconnnnnonnnnnonononnnnnnnncnnnnnnnnnnnnnnnnnnnnno 36 Chapter 8 LACP CommandS essccsisscccssccnstcacassssaatenncsossedssnsatnanaueasnassneutansmneancenaeces 37 acp System pi OT I r a tenet aa r a Aa Ten a a aA AE DEn aa Aer a DEEE 3T lacp interface mini e e e a en a e ea a EEA A NA EEA E ARa seat 37 l cp admin Keyi tea E AT 38 l cp POM PRIONIY ec a a a a aa a teen deere as 38 SHOW lacp interface a a Ea a cee R E Daai 39 Show lacp System prlority s oieee aiii iieii A i 39 Chapter 9 User Manage Comman ci it ii ii ini lini 41 USCA ari laica 41 E A ta TETAAN ad sabe cec ee ee alk ae 42 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide USE MOdIfy Status iii A AR agen cece dE doy Quest 42 USC Modify ty Pe Avs seh eh eae sc nd yee Goh AAA AAA Maiden a 43 USEF modify password says Nestea aa ee ee eet 43 user access control disable cuina ira ada 44 user access control IP DASEC eee ee cece cece cece cette cette eee eeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeteg 44 user access control mac based e sseessesrrerrrerrrerrserrstrrstrrstrrstrrerrrerrretrrerrrerrrerrrertrerrrere 45 user access control port based coocccnnccnnconnnennnennnennnennnonnnnnnnen
120. naged by the SNMP management station TP LINK config snmp view add view1 1 3 6 1 6 3 20 include snmp group add Description The snmp group add command is used to manage and configure the SNMP group To delete the corresponding SNMP group please use no snmp group add command SNMP v3 provides the VACM View based Access Control Model and USM User Based Security Model mechanisms for authentication The users in the SNMP Group can manage the device via the 168 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Read View Write View and Notify View And the authentication mode and the privacy mode guarantee the high security for the communication between the management station and the managed device Syntax snmp group add name smode v1 v2c v3 slev noAuthNoPriv authNoPriv authPriv ro ro view wo wo view notify notify view no snmp group add name smode v1 v2c v3 slev noAuthNoPriv authNoPriv authPriv Parameter name The SNMP Group name ranging from 1 to 16 characters The Group Name Security Model and Security Level compose the identifier of the SNMP Group These three items of the Users in one group should be the same smode Security Model with v1 v2c and v3 options They represent SNMP v1 SNMP v2c and SNMP v3 SNMP v1 and SNMP v2c are both authenticated by Community Name please refer snmp community add for detailed information
121. ncnnononnonannn nono nnncnnanannennnes 162 show igmp snooping POTE CONfIO cocononnncocccnccoconncononncnnnnonnnncnnonnnnnonnnnonannnnnnnnnnnnnennnnnnnnnnnnnnno 162 show igmp snooping vlan config ccccceeceeeceeeeeeeeeeeeeeeeeeaeeceeeeeeeseeceasaeeeeeeeeesetenseeeeeees 163 show igmp snooping multi vlan ooooconociciniciniconinccnccnncrnn nn in nin ni ri rre 163 show igmp snooping multi ip list 0 ccc ceeeeeee eee eeee eee eee nnncnnncnnnnnnnnnno nono nn nono nono nono nnnnnnnnnos 164 show igmp snooping filter ip addr ooooooooccccccccoocananacccocononacanonanc nono ncnncnnnn no nnnnncnonannnnnnncnnnnos 164 show igmp snooping port filter ooooonnnoncccconononocononoccnnncnnoncnnnnnncnnnnnnnnnonannnnnnnnnnnnnanannnnnes 164 show igmp snooping packet Stat 0 cc ceeeeeeeeeeeeeee eee eee eee eee eee eee a anne nono nnnnnnnonnnos 165 show igmp snooping packet stat Clear 0 0 0 0 cece eeeeeeeeeeeeeeeeeee cece eeee eee eae nn ncnno nono nono nnnonnnnnnnns 165 Chapter 26 SNMP CoMMAandS ooonncccccccccononcncnnnononcnnnnnnanannnnnnnnnnnnnnnnannnnnrnnennnnnnnnans 167 aiok o t EEA A nae enced eae eave ered e 167 snmp VieW addies 2a ai A lA ani aie ini Redd leads 168 simp group add tii AA eh ae a 168 SMMP USCl AdG eeke a e AE E n red ancerdsaed ed EAE neers 170 SNIMp commu A O 171 SNMP notity add ieo oe E ii dn andy A nay a 172 snmp rmon history sample cfg oooocococccococonocccoccccnncononononnnnnnonnnnnnnnnnnnnnn
122. nd enabled the switch can terminate receiving the ARP packets for 300 seconds when the transmission speed of the legal ARP packet on the port exceeds the defined value so as to avoid ARP Attack flood Syntax arp detection no arp detection Command Mode Interface Configuration Mode interface ethernet interface range ethernet Example Enable the arp defend function for the ports 2 6 TP LINK config interface range ethernet 2 6 TP LINK config if arp detection arp detection limit rate Description The arp detection limit rate command is used to configure the speed The 60 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide switch can terminate receiving the ARP packets for 300 seconds when the transmission speed of the legal ARP packet on the port exceeds the defined value To restore to the default speed please use no arp detection limit rate command Syntax arp detection limit rate va ue no arp detection limit rate Parameter value The value to specify the maximum amount of the received ARP packets per second ranging from 10 to 100 in pps packet second By default the value is 15 Command Mode Interface Configuration Mode interface ethernet interface range ethernet Example Configure the maximum amount of the received ARP packets per second as 50 pps for the port 5 TP LINK config interface ethernet 5 TP LINK config if arp detection limit rate 50 arp
123. network with stable topology It ranges from 1 to 28 Command Mode Global Configuration Mode Example Modify Router Port Time as 300 seconds Member Port Time as 200 seconds and Leave time as 15 seconds for VLAN 1 TP LINK config igmp snooping vian config 1 rtime 300 mtime 200 Itime 15 igmp snooping multi vlan config Description The igmp snooping multi vlan config command is used to create Multicast VLAN To delete the corresponding Multicast VLAN please use no igmp snooping multi vlan config command Syntax igmp snooping multi vlan config disable enable vic rtime router time mtime member time Itime eave time rport router port no igmp snooping multi vlan config Parameter disable enable Enable Disable Multicast VLAN vid The ID of the VLAN desired to modify configuration ranging from 2 to 4094 router time Router Port Time Within this time if the switch does not receive IGMP query message from the router port it will consider this port is not a router port any more Router Port Time ranges from 60 to 600 in seconds By default it is 300 158 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide member time Member Port Time Within this time if the switch does not receive IGMP report message from the member port it will consider this port is not a member port any more Member Port Time ranges from 60 to 600 in seconds By default it is 260 leave t
124. nnnnnrnnnnnnnennnennnennnennnenenenineninen 45 USSFMDENAUMDE ui AA A a A 46 A A TO 46 Show user accoUn blica e tre 47 show user CONFIQUIALION cece ceeeceeeeeee cece ceeeeeeeeeee aces eeeeee ceneaaeeeeeeeeeesecdceeeaeeeeeeeeseneeieaeeeseeeess 47 Chapter 10 Binding Table Command6 eee titi itn innit 49 DINGING taADlS USEING esc 5 25 O 49 DINGING ta DIS TEMOVE cuac Penne Eaei a Ea EEE anaa Da EEEa 50 CNEP SNOOPING eines wre Nal aie ane ee nal Aa eed aes ae ees 50 dhep sniooping glo Dall sense Mee Ae eR Ae ee aa AA 51 dhcp snooping information enable ccccccceeceeceeeeeeeeeeeececceneeceeeeeeeeeecseeeeeeeeeteeeeuseeeees 52 dhcp snooping information strategy c ccccceceeeceeceeeceeeeeeeseeeeneeceeeeeeeseeceeeeeeeeeeeseeseseaeees 52 dhcp snooping information user defined 2 0 0 2 2 cee ceeeeeeeceee cece ceeeeneeceeeceeeeeeecneeaeeeeeeeeeeesnseneeees 53 dhcp snooping information remote id cccccceeeceeeeeeeeeeeeeeeeeeeeneeceeeceeeeeeecnaeeeeeeeeeseeseseneeees 53 dhcp snooping information CirCuit id ccccecceceeeceeceeeeeeeeceeeceeecneeeeeeeeeesescenaeeeeeeeeeseesnseneeees 54 ANCp SNOOPING MUS A iia AAA 54 ANCP SNOOPING MAC VETIFY eisein Eae Ea Eea aa Eea aiani 55 dhcp snooping rate limit 0 0 0 0 ll nn nn rn 55 dhcp snooping decline ii ii ili iii lll inn i i li iii ieee ene 56 Show DINdING lable Fase treet atic i 56 show dhcp snooping gloDall aiaa aeir ea ate
125. no radius accounting secondary ip command Syntax radius accounting secondary ip p addr 75 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide no radius accounting secondary ip Parameter ip addr The IP address of the alternate accounting server By default it is 0 0 0 0 Command Mode Global Configuration Mode Example Configure the IP address of the alternate accounting server as 10 20 1 101 TP LINK config radius accounting secondary ip 10 20 1 101 radius accounting port Description The radius accounting port command is used to set the UDP port of accounting server s To restore to the default value please use no radius accounting port Syntax radius accounting port port num no radius accounting port Parameter port num The UDP port of accounting server s ranging from 1 to 65535 The default port is 1813 Command Mode Global Configuration Mode Example Set the UDP port of accounting server s as 1816 TP LINK config radius accounting port 1816 radius accounting key Description 76 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide The radius accounting key command is used to configure the shared password for the switch and the accounting servers to exchange messages To clear the shared password for the switch and the accounting servers please use no radius accounting key command Syntax radius accounting key key string
126. nse from the management station before resending a request ranging from 1 to 3600 in seconds Command Mode Global Configuration Mode Example Add a Notification entry and configure the IP Address of the management Host as 192 168 0 1 the UDP port as 162 the User name of the management station as admin the Security Model of the management station as v2c the type of the notifications as inform the maximum time for the switch to wait as 1000 seconds and the resending time as 100 TP LINK config snmp notify add 192 168 0 1 162 admin smode v2c type inform resend 100 timeout 1000 snmp rmon history sample cfg Description The snmp rmon history sample cfg command is used to configure the history sample entry To return to the default configuration please use no snmp rmon history sample cfg command RMON Remote Monitoring basing on SNMP architecture functions to monitor the network History Group is one of the commonly used RMON Groups After a history group is configured the switch collects network statistics information periodically based on which the management station can monitor network effectively Syntax snmp rmon history sample cfg index port interval no snmp rmon history sample cfg index Parameter index The index number of the entry ranging from 1 to 12 in the format of 1 3 5 port The port from which the history samples were taken ranging from 1 to 28 interval The interval to take
127. ntrol the forwarding sequence of the packets according to the priority queues and scheduling algorithms you set On this switch the priority levels are labeled as TCO TC1 TC3 Syntax qos scheduler sp wrr sp wrr equ no qos scheduler Parameter sp Strict Priority Mode In this mode the queue with higher priority will occupy the whole bandwidth Packets in the queue with lower priority are sent only when the queue with higher priority is empty 122 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide wrr Weight Round Robin Mode In this mode packets in all the queues are sent in order based on the weight value for each queue The weight value ratio of TCO TC1 TC2 and TC3 is 1 2 4 8 sp wrr Strict Priority Weight Round Robin Mode In this mode the switch provides two scheduling groups SP group and WRR group Queues in SP group and WRR group are scheduled strictly based on Strict Priority mode while the queues inside WRR group follow the WRR mode In SP WRR mode TC3 is the SP group TCO TC1 and TC2 belong to the WRR group and the weight value ratio of TCO TC1 and TC2 is 1 2 4 In this way when scheduling queues the switch allows TC3 to occupy the whole bandwidth following the SP mode and the TCO TC1 and TC2 in the WRR group will take up the bandwidth according to their ratio 1 2 4 equ Equal Mode In this mode all the queues occupy the bandwidth equally The weight
128. o 1000000 in kbps osd Out of Band disposal of Stream Condition It is the disposal way of the data packets those are transmitted beyond the rate There are two options none and discard By default the option is none egress port The Destination Port of Redirect The data packets those match the corresponding ACL will be forwarded to the specific port The destination port ranges from 1 to 28 By default it is All Ports vian id The VLAN ID of Redirect The data packets those match the corresponding ACL will be forwarded in the specific VLAN The VLAN ID ranges from 1 to 4094 139 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide mirror The Mirror Port of Stream Mirror ranging from 1 to 28 By default it is 1 Command Mode Global Configuration Mode Example Create a Policy named policy1 For the data packets those match ACL 120 in the policy if the rate beyond 1000kbps will be discarded by the switch TP LINK config acl policy policy add policy1 TP LINK config acl policy action add policy1 120 rate 1000 osd discard acl edit action Description The acl edit action command is used to edit actions for the policy Syntax acl edit action policy name acl id rate rate osd none discard e port egress porf vid vlan id mirr mirror Parameter policy name The Policy Name ranging from 1 to 16 characters acl id The ACL for configuration in
129. obal Configuration Mode Example Configure port 3 as mirrored port port 4 as mirroring port the mirror mode as both and group number as 1 TP LINK config mirror add 3 4 both 1 User Guidelines 1 The mirroring port is corresponding to current interface configuration mode 126 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide 2 Mirrored ports number is not limited but it can t be the mirroring port at the same time 3 Whether the mirroring port and mirrored ports are in the same VLAN or not is not demanded strictly 4 The mirroring port and mirrored ports cannot be link aggregation member mirror remove group Description The mirror remove group command is used to remove mirror group Syntax mirror remove group group num Parameter group num The group number of mirror group Command Mode Global Configuration Mode Example Remove mirror group 1 TP LINK config mirror remove group 1 mirror remove mirrored Description The mirror remove mirrored command is used to remove the mirrored port from the mirror group Syntax mirror remove mirrored mirrored port group num Parameter Mirrored port The port to be monitored group num The group number of mirror group Command Mode Global Configuration Mode Example Remove mirrored port 1 2 4 from mirror group 1 127 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide
130. oping filter ip addr Description The show igmp snooping filter ip addr command is used to display the Multicast Filter IP Range table Syntax show igmp snooping filter ip addr Command Mode Any Configuration Mode Example Display the Multicast Filter P Range table TP LINK config show igmp snooping filter ip addr show igmp snooping port filter Description The show igmp snooping port filter command is used to display the configuration of Multicast Port Filter Syntax 164 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide show igmp snooping port filter port num Parameter port num The port selected to display the configuration of Multicast Filter ranging from 1 to 28 By default the configuration of all ports is displayed Command Mode Any Configuration Mode Example Display the Multicast Filter configuration of port 5 TP LINK gt show igmp snooping port filter 5 show igmp snooping packet stat Description The show igmp snooping packet stat command is used to display the Packet Statistics information of all ports Syntax show igmp snooping packet stat Command Mode Any Configuration Mode Example Display the Packet Statistics information TP LINK gt show igmp snooping packet stat show igmp snooping packet stat clear Description The show igmp snooping packet stat clear command is used to clear the Packet Statistics information of all ports Synta
131. ow bridge aging time Command Mode Any Configuration Mode Example Display the Aging Time of the MAC address TP LINK config show bridge aging time 97 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Chapter 18 System Commands System Commands can be used to configure the System information and System IP reboot and reset the switch upgrade the switch system and other operations system descript Description The system descript command is used to configure the Device Name Device Location and System Contact To clear all the information please use no system descript command Syntax system descript sysname sysname location ocation contact info contact_info no system descript sysname location contact_info Parameter sysname System Name Device Name The length of the name ranges from 1 to 32 characters By default it is empty location Device Location It consists of 32 characters at most By default it is empty contact_info Contact Information It consists of 32 characters at most By default it is empty Command Mode Global Configuration Mode Example Configure the System Contact as www tp link com cn TP LINK config system descript contact info www tp link com cn system time gmt Description The system time gmt command is used to configure the time zone and the IP Address for the NTP Server Syntax 98 TL SL3428 Jet
132. pe is absolute r hold The rising counter value that triggers the rising threshold alarm ranging from 1 to 65535 By default it is 100 r event Rise Event which is the index of the corresponding event which will be triggered if the sampled value is larger than the Rising Threshold It ranges from 1 to 12 f hold The falling counter value that triggers the falling threshold alarm ranging from 1 to 65535 By default it is 100 f event Fall Event which is the index of the corresponding event which will be triggered if the sampled value is lower than the Falling Threshold It ranges from 1 to 12 a type Alarm Type with rise fall and all options Rise indicates that the alarm event will be triggered when the sampled value exceeds the Rising Threshold fall indicates that the alarm event will be triggered when the sampled value is under the Falling Threshold and all indicates that the alarm event will be triggered either the sampled value exceeds the Rising Threshold or is under the Falling Threshold By default the Alarm Type is all interval The alarm interval time ranging from 10 to 3600 in seconds By default it is 1800 Command Mode Global Configuration Mode Example Configure the alarm interval time of the entries 1 2 3 and 6 as 1000 seconds TP LINK config snmp rmon alarm config 1 3 6 interval 1000 snmp rmon alarm owner Description The snmp rmon alarm owner command is used to config
133. port Security oooccccccnncnnnonononnncnnnonnncnnnnonnnonnnnnnonnnnnnnnnnnnnnnnnnnnnnnnnnnenineniness 93 Dridge address Static A loa En 94 DMdGSAGING UIM Sais ra iia 95 bridge address filtering iodo iii iia di 95 Show bridge port SecuUr Vacio Aaa sey dine ii 96 SNOW bridge AdALESS vicio A ta Da ee Un alee 96 SHOW bridge AIN UMS cda ada 97 Chapter 18 System Commands cocccncnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn 98 syst m d script irio de ee eet ae AA ie aE 98 SYSLOM UMS CM ae Sacer touk so lA a E li bevel bi auger AT 98 system Ime MAMA tactica eae each 99 system Sts reste eae eA cetacean Ate a 99 IP AGGIES nreclea ticle E O 100 IP management VAM ctegsees A E 101 Ip dhcpralloe viv sete A te eng ie dine eee i ing EEN Kie 101 IP DOOtP aAllOC ria EENE TA EEN A E A T T usb apaa ea tacgeutanniaed tient 101 A nh caecodueed bewivda cave ede china aye cates anced Mesure decile ae aU ee 102 PEDO OU A A aaa 102 USEF CONTIG DACKU Dit aa cada Midas detent alten ia AAA 103 vi TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide USER COMO iii A tds olny 103 US ORCOS VELA A SA a A E ENANA S 104 firimware UPGrade ii A ede ae 104 A O Rd 105 A TO 105 o O 106 SHOW SYStOM INIOs amis re REDEE EAA 106 SNOW Ip ACCESS a A ead 107 SHOW SYSLOM UME pa ee ett sec see 107 Show system time dst 4 scciidAn acne eh e tere 108 show system tiMe SOUICE eect eee eeee eee et eee eee eee eae 108 Show system time Mode
134. r Syntax firmware upgrade filename name ip address p addr Parameter name Specify the name for the Firmware File ip addr IP Address of the TFTP server Command Mode Privileged EXEC Mode Example Upgrade the switch system via the TFTP server with the IP 192 168 0 148 TP LINK firmware upgrade filename firmware bin ip address 192 168 0 148 104 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide ping Description The ping command is used to test the connectivity between the switch and one node of the network Syntax ping ip_adadr n count I count i count Parameter ip_addr The IP address of the destination node for ping test count n The amount of times to send test data during Ping testing It ranges from 1 to 10 By default this value is 4 count 1 The size of the sending data during ping testing It ranges from 1 to 1024 bytes By default this value is 64 count i The interval to send ICMP request packets It ranges from 100 to 1000 milliseconds By default this value is 1000 Command Mode User EXEC Mode and Privileged EXEC Mode Example To test the connectivity between the switch and the network device with the IP 192 168 0 131 please specify the count l as 512 bytes and count i as 1000 milliseconds If there is not any response after 8 times Ping test the connection between the switch and the network device
135. rameter aging time Aging time in minutes to be set for the Voice VLAN It ranges from 1 to 43200 and the default value is 1440 Command Mode Global Configuration Mode Example Set the aging time for the Voice VLAN as 2880 minutes TP LINK config voice vlan aging time 2880 voice vlan oui Description The voice vlan oui command is used to create or delete Voice VLAN OUI Syntax voice vlan oui add mac addr mask mask addr description voice vlan oui remove mac addr Parameter mac addr The OUI address of the voice device mask addr The OUI address mask of the voice device description Give a description to the OUI for identification which contains 16 characters at most By default it is empty Command Mode Global Configuration Mode Example Create a Voice VLAN OUI descripted as TP LINK Phone with the MAC address 00 01 E3 00 00 01 and the mask address FF FF FF 00 00 00 And then delete the Voice VLAN OUI with the MAC address 00 00 00 11 00 01 TP LINK config voice vian oui add 00 01 E3 00 00 01 mask FF FF FF 00 00 00 TP LINK Phone TP LINK config voice vlan oui remove 00 00 00 11 00 01 26 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide switchport voice vlan mode Description The switchport voice vlan mode command is used to configure the Voice VLAN mode for the Ethernet port Syntax switchport voice vlan mode manual auto Parameter manual
136. rameter index The index number of the entry desired to enable ranging from 1 to 12 in the format of 1 3 5 Command Mode Global Configuration Mode Example Enable the history sample entries 1 2 3 4 and 8 TP LINK config snmp rmon history enable 1 4 8 snmp rmon event user Description The snmp rmon event user command is used to configure the user name of SNMP RMON Event To return to the default configuration please use no snmp rmon event user command Event Group as one of the commonly used RMON Groups is used to define RMON events Alarms occur when an event is detected Syntax snmp rmon event user index user no snmp rmon event user index Parameter index The index number of the event entry ranging from 1 to 12 You can only select one entry for each command user The name of the User to which the event belongs ranging from 1 to 16 characters By default it is public Command Mode Global Configuration Mode Example Configure the user name of entry 1 as user1 TP LINK config snmp rmon event user 1 user 175 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide snmp rmon event description Description The snmp rmon event description command is used to configure the description of SNMP RMON Event To return to the default configuration please use no snmp rmon event description command Syntax snmp rmon event description index description no snmp
137. re the default value please use no lacp admin key command Syntax lacp admin key value no lacp admin key Parameter value admin key ranging from O to 65535 By default the value is 1 Command Mode Interface Configuration Mode interface ethernet interface range ethernet Example Configure the admin key of port 1 as 1024 TP LINK config interface ethernet 1 TP LINK config if lacp admin key 1024 lacp port priority Description The lacp port priority command is used to set the priority of the current port To restore to the default priority please use no lacp port priority command Syntax lacp port priority value no lacp port priority 38 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Parameter value Port priority ranging from O to 65535 By default the value is 32768 Command Mode Interface Configuration Mode interface ethernet interface range ethernet Example Set the port priority of port 1 to 1024 TP LINK config interface ethernet 1 TP LINK config if lacp port priority 1024 show lacp interface Description The show lacp interface command is used to display the port configuration information of LACP Syntax show lacp interface ethernet port num Parameter port num The Ethernet port number By default display the configuration information of all the Ethernet ports Command Mode Any Configuration Mode Example Display t
138. rivileged EXEC Mode Example Return to User EXEC Mode from Privileged EXEC Mode TP LINK disable TP LINK gt configure Description The configure command is used to access Global Configuration Mode from Privileged EXEC Mode Syntax configure Command Mode Privileged EXEC Mode Example Access Global Configuration Mode from Privileged EXEC Mode TP LINK configure TP LINK config exit Description The exit command is used to return to the previous Mode from the current Mode Syntax 14 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide exit Command Mode Any Configuration Mode Example Return to Global Configuration Mode from Interface Configuration Mode and then return to Privileged EXEC Mode TP LINK config if exit TP LINK config exit TP LINK end Description The end command is used to return to Privileged EXEC Mode Syntax end Command Mode Any Configuration Mode Example Return to Privileged EXEC Mode from Interface Configuration Mode TP LINK config if end TP LINK 15 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Chapter3 IEEE 802 1Q VLAN Commands VLAN Virtual Local Area Network technology is developed for the switch to divide the LAN into multiple logical LANs flexibly Hosts in the same VLAN can communicate with each other regardless of their physical locations VLAN can enhance performance b
139. rm Group is one of the commonly used RMON Groups RMON alarm management allows monitoring the specific alarm variables When the value of a monitored variable exceeds the threshold an alarm event is generated which triggers the switch to act in the set way Syntax snmp rmon alarm config index var drop revbyte revpkt bpkt mpkt crc align undersize oversize fragment jabber collision 64 65 127 128 255 256 511 512 1023 1024 10240 port port s type absolute increment 3 r hold r hold r event r event f hold f hola f event f event a type rise fall all interval interval no snmp rmon alarm config index Parameter index The index number of the Alarm Management entry ranging from 1 to 12 in the format of 1 3 5 var The alarm variable By default the option is drop port The port on which the Alarm entry acts ranging from 1 to 28 s type Sample Type which is the sampling method for the selected variable and comparing the value against the thresholds There are two options absolute and increment Absolute indicates comparing the values directly with 178 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide the thresholds at the end of the sampling interval Increment indicates subtracting the last sampled value from the current value and then comparing the difference in the values with the threshold By default the Sample Ty
140. rnet port numbers You can appoint 5 ports at most 45 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Command Mode Global Configuration Mode Example Enable the access control of the ports 2 port4 port5 port6 and port10 TP LINK config user access control port based 2 4 6 10 user max number Description The user max number command is used to configure the number of the users logging on at the same time To cancel the limit to the numbers of the users logging in please use no user max number command Syntax user max number admin num guest num no user max number Parameter admin num The maximum number of the users logging on as Admin ranging from 1 to 16 The total number of Admin and Guest should be less than 16 guest num The maximum number of the users logging on as Guest ranging from 0 to 15 The total number of Admin and Guest should be less than 16 Command Mode Global Configuration Mode Example Configure the number of the users as Admin and Guest logging on as 5 and 3 TP LINK config user max num 5 3 user idle timeout Description The user idle timeout command is used to configure the timeout time of the 46 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide switch To restore to the default timeout time please use no user idle timeout command Syntax user idle timeout minutes no user idle timeout Parameter min
141. rsion v1 v2 Parameter v1 v2 The SSH protocol version to be enabled They represent SSH v1 and SSH v2 respectively Command Mode Global Configuration Mode Example 86 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Enable SSH v2 TP LINK config ssh version v2 ssh idle timeout Description The ssh idle timeout command is used to specify the idle timeout time of SSH To restore to the factory defaults please use no ssh idle timeout command Syntax ssh idle timeout value no ssh idle timeout Parameter value The ldle timeout time During this period the system will automatically release the connection if there is no operation from the client It ranges from 1 to 999 in seconds By default this value is 500 Command Mode Global Configuration Mode Example Specify the idle timeout time of SSH as 300 seconds TP LINK config ssh idle timeout 300 ssh max client Description The ssh max client command is used to specify the maximum number of the connections to the SSH server To return to the default configuration please use no ssh max client command Syntax ssh max client number no ssh max client Parameter number The maximum number of the connections to the SSH server It ranges from 1 to 5 By default this value is 5 Command Mode 87 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Global Configuration
142. rwarded by the switch TP LINK config acl edit rule std acl 120 10 op permit dip 192 168 0 100 dmask 255 255 255 0 tseg tSeg1 acl policy policy add Description The acl policy policy add command is used to add Policy To delete the corresponding Policy please use no acl policy policy add command A Policy is used to control the data packets matching the corresponding ACL rules by configuring ACLs and actions together for effect The operations here include stream mirror stream condition and redirect 138 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Syntax acl policy policy add name no acl policy policy add name Parameter name The Policy Name ranging from 1 to 16 characters Command Mode Global Configuration Mode Example Add a Policy named policy1 TP LINK config acl policy policy add policy1 acl policy action add Description The acl policy action add command is used to add ACLs and create actions for the policy To delete the corresponding actions please use no acl policy action add command Syntax acl policy action add policy name acl id rate rate osd none discard e port egress port vid vian id mirr mirror no acl policy action add policy name acl id Parameter policy name The Policy Name ranging from 1 to 16 characters acl id The ACL for configuration in the policy rate The rate of Stream Condition ranging from 1 t
143. rwarded by the switch per second The excessive massages will be discarded The options are 0 10 20 30 40 50 packet second By default it is 0 standing for disable dec threshold The value to specify the minimum transmission rate of the Decline packets to trigger the Decline protection for the specific port The options are 0 5 10 15 20 25 30 packet second By default it is O standing for disable Dec rate The value to specify the Decline Flow Control The traffic flow of the corresponding port will be limited to be this value if the transmission rate of the Decline packets exceeds the Decline Threshold The options are 5 10 15 20 25 30 packet second By default it is 5 Command Mode Global Configuration Mode Example Configure the Global Flow Control as 30pps the Decline Threshold as 20 pps and decline Flow Control as 20 pps for DHCP Snooping TP LINK config dhcp snooping global global rate 30 dec threshold 20 dec rate 20 51 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide dhcp snooping information enable Description The dhcp snooping information enable command is used to enable the Option 82 function of DHCP Snooping To disable the Option 82 function please use no dhcp snooping information enable command Syntax dhcp snooping information enable no dhcp snooping information enable Command Mode Global Configuration Mode Example Enable the Option 82 function of
144. s used to edit Standard IP ACL rule Syntax acl edit rule std acl acl id rule id op discard permit sip source ip 137 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide smask source ip mask dip destination ip dmask destination ip mask tseg time segment index idx Parameter acl id The desired Standard IP ACL for configuration rule id The rule ID op The operation for the switch to process packets which match the rules There are two options discard and permit Discard means discarding packets and permit means forwarding packets By default the option is permit source ip The source IP address contained in the rule source ip mask The source IP address mask It is required if you typed the source IP address destination ip The destination IP address contained in the rule destination ip mask The destination IP address mask It is required if you typed the destination IP address time segment The time range for the rule to take effect By default it is not limited index Change the index number of the entry Command Mode Global Configuration Mode Example Edit Rule 10 for the Standard IP ACL whose ID is 120 In the rule the source IP address is 192 168 0 100 the source IP address mask is 255 255 255 0 the time range for the rule to take effect is tSeg1 and the packets match this rule will be fo
145. sable the IEEE 802 1X function for a specified port please use no dot1x command Syntax 69 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide dot1x no dot1x Command Mode Interface Configuration Mode interface ethernet interface range ethernet Example Enable the IEEE 802 1X function for the port 1 TP LINK config interface ethernet 1 TP LINK config if dot1x dot1x guest vlan Description The dot1x guest vlan command is used to enable the Guest VLAN function for a specified port To disable the Guest VLAN function for a specified port please use no dot1x guest vlan command Please ensure that the Control Type of the corresponding port is port based before enabling the Guest VLAN function for it Please refer to dot1x port method for details Syntax dot1x guest vlan no dot1x guest vlan Command Mode Interface Configuration Mode interface ethernet interface range ethernet Example Enable the Guest VLAN function for port 2 TP LINK config interface ethernet 2 TP LINK config if dot1x guest vlan dot1x port control Description The dot1x port control command is used to configure the Control Mode of IEEE 802 1X for the specified port To restore to the default configuration 70 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide please use no dot1x port control command Syntax dot1x port control auto authorized force unauthorize
146. sk destination mac mask vid vlan id type Ethernet type pri user pri tseg time segment no acl rule mac acl acl id rule id Parameter acl id The desired MAC ACL for configuration rule id The rule ID op The operation for the switch to process packets which match the rules There are two options discard and permit Discard means discarding packets and permit means forwarding packets By default the option is permit source mac The source MAC address contained in the rule source mac mask The source MAC address mask It is required if you typed the source MAC address destination mac The destination MAC address contained in the rule destination mac mask The destination MAC address mask It is required 134 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide if you typed the destination MAC address vian id The VLAN ID contained in the rule ranging from 1 to 4094 Ethernet type EtherType contained in the rule in the format of 4 hex number user pri The user priority contained in the rule ranging from O to 7 By default it is not limited time segment The time range for the rule to take effect By default it is not limited Command Mode Global Configuration Mode Example Create a MAC ACL whose ID is 20 and add Rule 10 for it In the rule the source MAC address is 00 01 3F 48 16 23 the source MAC addr
147. source ip mask dip destination ip damask destination ip mask tseg time segment no acl rule std acl acl id rule id Parameter acl id The desired Standard IP ACL for configuration rule id The rule ID op The operation for the switch to process packets which match the rules There are two options discard and permit Discard means discarding packets and permit means forwarding packets By default the option is permit source ip The source IP address contained in the rule source ip mask The source IP address mask It is required if you typed the source IP address destination ip The destination IP address contained in the rule destination ip mask The destination IP address mask It is required if you typed the destination IP address time segment The time range for the rule to take effect By default it is not limited Command Mode Global Configuration Mode Example Create a Standard IP ACL whose ID is 120 and add Rule 10 for it In the rule the source IP address is 192 168 0 100 the source IP address mask is 255 255 255 0 the time range for the rule to take effect is tSeg1 and the packets match this rule will be forwarded by the switch TP LINK config acl create 120 TP LINK config acl rule std acl 120 10 op permit dip 192 168 0 100 dmask 255 255 255 0 tseg tSeg1 acl edit rule std acl Description The acl edit rule std acl command i
148. ss ices ateec E asic act eeventetasd cattieecbeac seit E teats eee 76 FACIUS TESPONSE UIMBOULS unta 77 SHOW GOUT x globala a dde 78 SHOW GotlXcintenace it As 78 show radius authentication 0 nn nn nn nn nl i i i iene eee 79 SNOW rAdiUS ACCOUNTING areena eee ease case aaeeaeeeaaeeaaeeaeeaaee sees sues sees EENAA anaa aE AEE ENAA AA Tan E 79 Chapter 14 Log Commands ttt ttt n nn nnn nnn nnn niinnnnineeeeeeeee 80 logging loCal Puffen Grot en Annie ia Bena E ean ancl are aan 80 logging local fash ieinter neaei eea dd lena ariete dee 81 NN 81 lOGGING IOQHOSE aing i dete caditeed thee a eae ar a e ania ne ad 82 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide show logging local CONnfig ceceeeeeee cece ceeeeeeeeeee Eiaa ae EEEN a EEEE AEE a 83 show logging loghoSt ssr ndn a ai e 83 SHOW logging DI oi A Sg de ed eee cee 84 SHOW logging tas ivonne ie pibas paa tano 84 Chapter 15 SSH COmm ans Sosa mennenm nnmnnn 86 SSISEIVET CNADIS oi A dt 86 ANA e 86 SSMIGIO CIMGOUT dE 87 SIMA A ia 87 Ssh downoad yasni o oe daba dE 88 SNOW SSN vii AA e A en i ME ee 88 Chapter 16 SSL COMMANA Suisse AE AIRE IAS 90 SSL SM ADS td cr 90 ssl download Certificate ssnin aaa a aaea a aa EE a i aiaia 90 ssl download Key adiret ineeie ee EE i oE a 91 SNOW SSI a A eek a A A AS 91 Chapter 17 Address COMMANdS ccccccccconnncncncncncncncnnnanannnnnnnnnnnennnanannnnnnnnnnnnnnnanans 93 bridge address
149. switch TP LINK config show cluster manage role 191
150. t To disable the cluster function for the port please use no cluster command Syntax cluster ndp disable enable ntdp disable enable no cluster Parameter ndp Enable Disable NDP function for the port By default it is enabled ntdp Enable Disable NTDP function for the port By default it is enabled Command Mode Interface Configuration Mode interface ethernet interface range ethernet Example Enable NDP and NTDP function for port 5 TP LINK config interface ethernet 5 TP LINK config if cluster ndp enable ntdp enable 187 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide cluster manage role change Description The cluster manage role change command is used to change the role of the current switch According to their status and functions switches in the cluster play different roles You can specify the role the switch plays appropriate to your needs A commander switch can recognize and manage the devices in the cluster a member switch is managed by the commander a candidate switch does not belong to any cluster through it can be added to a cluster an individual switch is with the cluster feature disabled Syntax cluster manage role change candidate individual Parameter candidate individual The role you want the switch to play with candidate and individual options The role of the switch you can change to is related with the current role Th
151. t no description Parameter descript String to describe the VLAN which contains 16 characters at most Command Mode Interface Configuration Mode interface vlan Example Specify the description string of the VLAN 2 as vlan 2 17 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide TP LINK config interface vlan 2 TP LINK config if description vian2 switchport type Description The switchport type command is used to configure the Link Types for the ports Syntax switchport type access trunk general Parameter access trunk general Link Types There are three Link Types for the ports Command Mode Interface Configuration Mode interface ethernet interface range ethernet Example Specify the Link Type of port 5 as general TP LINK config interface ethernet 5 TP LINK config if switchport type general switchport allowed vian Description The switchport allowed vian command is used to add the desired port to IEEE 802 1Q VLAN or to remove a port from the corresponding VLAN Syntax switchport allowed vlan add vian list switchport allowed vlan remove vian list Parameter vlan list VLAN ID list it is multi optional Command Mode Interface Configuration Mode interface ethernet interface range ethernet Example Add port 2 to IEEE 802 1Q VLAN 18 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI
152. t Security function for a specified port By default this function is disabled 93 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Command Mode Interface Configuration Mode interface ethernet interface range ethernet Example Enable Port Security function for port1 select Static mode as the learn mode and specify the maximum number of MAC addresses that can be learned on this port as 30 TP LINK config interface ethernet 1 TP LINK config if bridge address port security max number 30 mode static status enable bridge address static Description The bridge address static command is used to add the static MAC address entry To remove the corresponding entry please use no bridge address static command The static address can be added or removed manually independent of the aging time In the stable networks the static MAC address entries can facilitate the switch to reduce broadcast packets and enhance the efficiency of packets forwarding remarkably Syntax bridge address static mac mac vid vid port port no bridge address static mac vid port Parameter mac The MAC address of the entry you desire to add vid The VLAN ID number of your desired entry lt ranges from 1 to 4094 port The Port number of your desired entry It ranges from 1 to 28 Command Mode Global Configuration Mode Example Add a static Mac address entry to bind the MAC address 00 02 58 4f 6c
153. t owner command is used to configure the owner of SNMP RMON Event To return to the default configuration please use no snmp rmon event owner command Syntax snmp rmon event owner index owner no snmp rmon event owner index Parameter index The index number of the event entry ranging from 1 to 12 You can only select one entry for each command owner The owner of the event entry ranging from 1 to 16 characters By default it is monitor Command Mode Global Configuration Mode Example Configure the owner of entry 1 as owner TP LINK config snmp rmon event owner 1 owner snmp rmon event enable Description The snmp rmon event enable command is used to enable SNMP RMON Event entry To disable the corresponding entry please use no snmp rmon event enable command Syntax 177 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide snmp rmon event enable index no snmp rmon event enable index Parameter index The index number of the entry desired to enable ranging from 1 to 12 in the format of 1 3 5 Command Mode Global Configuration Mode Example Enable the SNMP RMON Event entries 1 2 3 4 and 8 TP LINK config snmp rmon event enable 1 4 8 snmp rmon alarm config Description The snmp rmon alarm config command is used to configure SNMP RMON Alarm Management To return to the default configuration please use no snmp rmon alarm config command Ala
154. the BPDU is discarded Max Hops ranges from 1 to 40 in hop By default it is 20 Command Mode Global Configuration Mode Example Enable the STP function and configure the STP version as MSTP CIST priority as 4096 Hello Time as 4 seconds Max Age as 10 seconds Forward Delay as 10 seconds TxHold Count as 8pps and Max Hops as 15 hops TP LINK config spanning tree global status enable mode msip cist 4096 htime 4 mage 10 delay 10 hcount 8 mhop 15 spanning tree common config Description The spanning tree common config command is used to configure the parameters of the ports for comparison in the CIST and the common parameters of all instances To return to the default configuration please use no spanning tree common config command CIST Common and Internal Spanning Tree is the spanning tree in a switched network connecting all devices in the network Syntax spanning tree common config status disable enable pri priority expath expath consum inpath inpath consum edge disable enable ptop auto open closej no spanning tree common config Parameter status Enable Disable STP function for the desired port By default it is disabled priority Port Priority which must be multiple of 16 ranging from O to 240 By default the port priority is 128 Port Priority is an important criterion on 145 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide determining
155. the policy rate The rate of Stream Condition ranging from 1 to 1000000 in kbps osd Out of Band disposal of Stream Condition It is the disposal way of the data packets those are transmitted beyond the rate There are two options none and discard By default the option is none egress port The Destination Port of Redirect The data packets those match the corresponding ACL will be forwarded to the specific port The destination port ranges from 1 to 28 By default it is All Ports vian id The VLAN ID of Redirect The data packets those match the corresponding ACL will be forwarded in the specific VLAN The VLAN ID ranges from 1 to 4094 mirror The Mirror Port of Stream Mirror ranging from 1 to 28 By default it is 1 Command Mode Global Configuration Mode 140 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Example Edit the actions for the policy1 For the data packets those match ACL 120 in the policy if the rate beyond 1000kbps will be discarded by the switch TP LINK config acl edit action policy1 120 rate 1000 osd discard acl bind to port Description The acl bind to port command is used to bind a policy to a port To cancel the bind relation please use no acl bind to port command Syntax acl bind to port policy name port no acl bind to port policy name port Parameter policy name The name of the policy desired to bind port
156. the time slice in the format of HH MM By default it is 00 00 end time The end time of the time slice in the format of HH MM By default it is 24 00 week day Period Mode in the format of 1 3 6 or daily off day working day 1 3 6 represent Monday Tuesday Wednesday and Saturday daily represents every day off day represents weekend and working day represents working day By default the period mode is disabled start date The start date in Absoluteness Mode in the format of MM DD YYYY By default it is 01 01 1970 end date The end date in Absoluteness Mode in the format of MM DD YYYY By default it is 12 31 2099 The absoluteness mode will be disabled if the start date and end date are both not configured holiday Enable Disable Holiday Mode By default it is disabled Command Mode Global Configuration Mode 132 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Example Edit the time range named tSeg1 with time from 8 30 to 12 00 at working day TP LINK config acl edit time segment tSeg1 start time 08 30 end time 12 00 week day working day acl holiday Description The acl holiday command is used to create holiday in Holiday Mode in the acl time segment command To delete the corresponding holiday please use no acl holiday command Syntax acl holiday name start date end date no acl holiday name Parameter name The holida
157. ticast IP is not in the IP range will be processed while accept indicates only the multicast packets whose multicast IP is in the 161 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide IP range will be processed By default the option is accept filter addr id The I P range ID the port will be bound to in the format of 1 3 4 6 Up to 15 IP Ranges can be bound to one port max group The maximum number of multicast groups for the port to join in It is used to prevent some ports taking up too much bandwidth Command Mode Interface Configuration Mode interface ethernet interface range ethernet Example Enable multicast filtering function for port 5 specify Action Mode as accept bound IP range 2 3 4 and specify the maximum number of multicast groups for port 5 to join in as 128 TP LINK config interface ethernet 5 TP LINK config if igmp snooping filter status enable mode accept addr id 2 4 maxgroup 128 show igmp snooping global config Description The show igmp snooping global config command is used to display the global configuration of IGMP Syntax show igmp snooping global config Command Mode Any Configuration Mode Example Display the global configuration of IGMP TP LINK gt show igmp snooping global config show igmp snooping port config Description The show igmp snooping port config command is used to display the port configuration of IGMP Syntax
158. time mtime member time Itime leave time rport router port no igmp snooping vlan config add vlan id Parameter vian id The ID of the VLAN desired to enable IGMP Snooping ranging from 1 to 4094 router time Router Port Time Within this time if the switch does not receive IGMP query message from the router port it will consider this port is not a router port any more Router Port Time ranges from 60 to 600 in seconds By 156 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide default it is 300 member time Member Port Time Within this time if the switch does not receive IGMP report message from the member port it will consider this port is not a member port any more Member Port Time ranges from 60 to 600 in seconds By default it is 260 leave time Leave Time which is the interval between the switch receiving a leave message from a host and the switch removing the host from the multicast groups Leave Time ranges from 1 to 30 in seconds By default it is 1 router port Static Router Port which is mainly used in the network with stable topology It ranges from 1 to 28 Command Mode Global Configuration Mode Example Enable IGMP Snooping for VLAN 1 and configure Router Port Time as 200 seconds Member Port Time as 100 seconds Leave time as 10 seconds and Static Router Port as port 1 TP LINK config igmp snooping vlan config add 1 rtime 200 mtime
159. tion The user access control ip based command is used to limit the IP range of the users for login Only the users within the IP range you set here are allowed for login Syntax user access control ip based p addr ip mask Parameter ip addr ip mask The IP source IP address Only the users within the IP range you set here are allowed for login Command Mode Global Configuration Mode 44 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Example Enable the access control of the user whose Ip address is 192 168 0 148 TP LINK config user access control ip based 192 168 0 148 255 255 255 255 user access control mac based Description The user access control mac based command is used to limit the MAC Address of the users for login Only the user with this MAC Address you set here are allowed for login Syntax user access control mac based mac addr Parameter mac addr The source MAC address Command Mode Global Configuration Mode Example Enable the access control of the user whose MAC address is 00 00 13 0A 00 01 TP LINK config user access control mac based 00 00 13 0A 00 01 user access control port based Description The user access control port based command is used to limit the ports for login Only the users connected to these ports you set here are allowed for login Syntax user access control port based port list Parameter port list The Ethe
160. tion Mode interface ethernet interface range ethernet Example Disable the ingress rate limit for port5 TP LINK config interface ethernet 5 TP LINK config if port rate limit disable ingress port rate limit disable egress Description The port rate limit disable egress command is used to disable the egress rate limit Syntax port rate limit disable egress Command Mode Interface Configuration Mode interface ethernet interface range ethernet Example Disable the egress rate limit for port5 TP LINK config interface ethernet 5 TP LINK config if port rate limit disable egress show interface configuration Description The show interface configuration command is used to display the configurations of an Ethernet port including Port status Bandwidth Control Negotiation Mode and Port description Syntax show interface configuration ethernet interface Parameter interface The port selected to display the configurations By default the 115 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide configuration information of all ports is displayed Command Mode Any Configuration Mode Example Display the configurations of port5 TP LINK show interface configuration ethernet 5 show interface status Description The show interface status command is used to display the connective status of an Ethernet port Syntax show interface status ethernet interface Par
161. tiple Ethernet ports at the same time Syntax interface range ethernet port list Parameter port list The list of the Ethernet ports to be configured Inconsecutive ports or port groups are separated by a comma with no space Use a hyphen to designate a range of ports for instance 1 10 indicates from port 1 to port 10 Command Mode Global Configuration Mode User Guidelines 110 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Command in the Interface Range Ethernet Mode is executed independently on all ports in the range It does not effect the execution on the other ports at all if the command results in an error on one port Example Enter the Interface Configuration Mode add ports 1 3 6 9 to the port list and configure them TP LINK config interface range ethernet 1 3 6 9 description Description The description command is used to add a description to the Ethernet port To clear the description of the corresponding port please use no description command Syntax description string no description Parameter string Content of a port description ranging from 1 to 16 characters Command Mode Interface Configuration Mode interface Ethernet Example Add a description Port 5 to port5 TP LINK config interface ethernet 5 TP LINK config if description Port 5 shutdown Description The shutdown command is used to disable an Ethernet port To enable this port
162. tocol template You can get the template corresponding to the number by the show protocol vlan template command Command Mode Global Configuration Mode Example Create a Protocol VLAN template named arp whose Ethernet protocol type is 0806 and delete the Protocol template whose number is 2 TP LINK config protocol vlan template add arp 0806 TP LINK config protocol vlan template remove 2 protocol vlan vlan Description The protocol vlan vlan command is used to create a Protocol VLAN entry To delete a Protocol VLAN entry please use no protocol vlan command Syntax 21 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide protocol vlan vlan vid template index no protocol vlan entry id Parameter vid VLAN ID ranging from 1 4094 index The number of the Protocol template You can get the template corresponding to the number by the show protocol vlan template command entry id The number of the Protocol VLAN You can get the Protocol VLAN entry corresponding to the number by the show protocol vlan vlan command Command Mode Global Configuration Mode Example Create a Protocol VLAN entry whose index is 1 and vid is 2 And then delete the Protocol VLAN entry whose number is 1 TP LINK config protocol vlan vlan 2 template 1 TP LINK config no protocol vlan vlan 1 protocol vlan interface Description The protocol vlan interface command is used to enable
163. trol Type is mas based Command Mode Interface Configuration Mode interface ethernet interface range ethernet Example Configure the Control Type for port 5 as port based TP LINK config interface ethernet 5 TP LINK config if dot1x port method port based radius authentication primary ip Description The radius authentication primary ip command is used to configure the IP address of the authentication server Authentication server provides the authentication service for the switch via the stored client information such as the user name password etc with the purpose to control the authentication and accounting status of the clients The RADIUS Remote Authentication Dial In User Service server is used as the Authentication server generally Syntax radius authentication primary ip p addr Parameter ip addr The IP address of the authentication server Command Mode Global Configuration Mode Example Configure the IP of the authentication server as 10 20 1 100 TP LINK config radius authentication primary ip 10 20 1 100 72 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide radius authentication secondary ip Description The radius authentication secondary ip command is used to configure the IP address of the alternate authentication server To restore to the default configuration please use no radius authentication secondary ip command Syntax radius authentication second
164. ult the GVRP configuration information of all the Ethernet ports is displayed Command Mode Any Configuration Mode Example Display the GVRP configuration information of all the Ethernet ports TP LINK config show gvrp interface 32 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Chapter 7 LAG Commands LAG Link Aggregation Group is to combine a number of ports together to make a single high bandwidth data path which can highly extend the bandwidth The bandwidth of the LAG is the sum of bandwidth of its member port interface link aggregation Description The interface link aggregation command is used to access the Interface Link aggregation Mode To delete the aggregation group please use no interface link aggregation command Syntax interface link aggregation group number no Interface link aggregation group number Parameter group number The LAG number ranging from1 to 14 Command Mode Global Configuration Mode Example Access the Interface Link aggregation Mode and configure the aggregation group 1 TP LINK config interface link aggregation 1 TP LINK config if interface range link aggregation Description The interface range link aggregation command is used to access the Interface range Link aggregation Mode and you can configure some aggregation groups at the same time To delete the aggregation group please use no interface range link aggregation command
165. unction globally To disable the ARP Detection function please use no arp detection command Syntax arp detection no arp detection Command Mode Global Configuration Mode Example Enable the ARP Detection function globally TP LINK config arp detection arp detection trust port Description The arp detection trust port command is used to configure the port for which the ARP Detect function is unnecessary as the Trusted Port To clear the Trusted Port list please use no arp detection trust port command The specific ports such as up linked port routing port and LAG port should be set as Trusted Port To ensure the normal communication of the switch please configure the ARP Trusted Port before enabling the ARP Detect function Syntax arp detection trust port port list no arp detection trust port 59 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Parameter port list The specified Trusted Port list Command Mode Global Configuration Mode Example Configure the ports 2 5 11 15 as the Trusted Port TP LINK config arp detection trust port 2 5 11 15 arp detection interface Description The arp detection interface command is used to enable the ARP Defend function To disable the arp detection function please use no arp detection command ARP Attack flood produces lots of ARP Packets which will occupy the bandwidth and slow the network speed extremely With the ARP Defe
166. ure the owner of the Alarm Management entry To return to the default configuration please use no snmp rmon alarm owner command Syntax 179 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide snmp rmon alarm owner index owner no snmp rmon alarm owner index Parameter index The index number of the entry ranging from 1 to 12 You can only select one entry for each command owner The owner of the entry ranging from 1 to 16 characters By default it is monitor Command Mode Global Configuration Mode Example Configure the owner of entry 1 as owner1 TP LINK config snmp rmon alarm owner 1 owner snmp rmon alarm enable Description The snmp rmon alarm enable command is used to enable SNMP RMON Alarm Management entry To disable the corresponding entry please use no snmp rmon alarm enable command Syntax snmp rmon alarm enable index no snmp rmon alarm enable index Parameter index The index number of the entry desired to enable ranging from 1 to 12 in the format of 1 3 5 Command Mode Global Configuration Mode Example Enable the Alarm Management entries 1 2 3 4 and 8 TP LINK config snmp rmon alarm enable 1 4 8 show snmp global config Description 180 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide The show snmp global config command is used to display SNMP configuration globally Syntax show snmp
167. ute The timeout time ranging from 5 to 30 in minutes By default the value is 10 Command Mode Global Configuration Mode Example Configure the timeout time of the switch as 15 minutes TP LINK config user idle timeout 15 show user account list Description The show user account list command is used to display the information of the current users Syntax show user account list Command Mode Any Configuration Mode Example Display the information of the current users TP LINK config show user account list show user configuration Description The user configuration command is used to display the security configuration 47 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide information of the users including access control max number and the idle timeout etc Syntax show user configuration Command Mode Any Configuration Mode Example Display the security configuration information of the users TP LINK config show user configuration 48 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Chapter 10 Binding Table Commands You can bind the IP address MAC address VLAN and the connected Port number of the Host together which can be the condition for the ARP Inspection to filter the packets binding table user bind Description The binding table user bind command is used to bind the IP address MAC address VLAN ID and the Port number tog
168. value ratio of all the queues is 1 1 1 1 Command Mode Global Configuration Mode Example Specify the Schedule Mode as Weight Round Robin Mode TP LINK config qos scheduler wrr show qos port based Description The show qos port based command is used to display the configuration of QoS based on port priority Syntax show qos port based interface num Parameter interface num The Ethernet port selected to display the configuration ranging from 1 to 28 By default information of all the ports is displayed Command Mode Any Configuration Mode Example Display the configuration of QoS for port 5 TP LINK show qos port based 5 123 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide show qos dot1p Description The show qos dot1p command is used to display the configuration of IEEE 802 1P Priority Syntax show qos dot1p Command Mode Any Configuration Mode Example Display the configuration of IEEE 802 1P Priority TP LINK show qos dot1p show qos dscp Description The show qos dscp command is used to display the configuration of DSCP Priority Syntax show qos dscp Command Mode Any Configuration Mode Example Display the configuration of DSCP Priority TP LINK show gos dscp show qos scheduler Description The show gos scheduler command is used to display the schedule rule of the egress queues Syntax show qos scheduler Command Mode 124 TL SL3428
169. x The entry number needed to be deleted You can use the show binding table command to get the idx Pay attention to that the entry number is the actual number in the binding table not arranged in an order Command Mode Global Configuration Mode Example Delete the IP MAC VID PORT entry with the index 5 TP LINK config binding table remove index 5 dhcp snooping Description The dhcp snooping command is used to enable the DHCP snooping function for the switch To disable the DHCP snooping function please use no dhcp snooping command DHCP Snooping functions to monitor the process of the Host obtaining the IP address from DHCP server and record the IP address MAC address VLAN and the connected Port number of the Host for automatic binding Syntax dhcp snooping no dhcp snooping Command Mode Global Configuration Mode Example 50 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Enable the DHCP snooping function globally TP LINK config dhcp snooping dhcp snooping global Description The dhcp snooping global command is used to configure the DHCP snooping globally To restore to the default value please use no dhcp snooping global command Syntax dhcp snooping global global rate g obal rate dec threshold dec threshold dec rate dec rate no dhcp snooping global Parameter global rate The value to specify the maximum amount of DHCP messages that can be fo
170. x show igmp snooping packet stat clear Command Mode Any Configuration Mode Example Clear the Packet Statistics information 165 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide TP LINK gt show igmp snooping packet stat clear 166 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Chapter 26 SNMP Commands SNMP Simple Network Management Protocol functions are used to manage the network devices for a smooth communication which can facilitate the network administrators to monitor the network nodes and implement the proper operation snmp global Description The snmp global command is used to configure the SNMP function globally To return to the default configuration please use no snmp global command Syntax snmp global status disable enable engine id engine id remote id remote id no snmp global Parameter status Enable Disable the SNMP function By default it is disabled engine id Local Engine ID for local clients The Engine ID is a unique alphanumeric string used to identify the SNMP engine on the switch Its length ranges from 10 to 64 hexadecimal characters which must be even number meanwhile remote id Remote Engine ID for the switch The Engine ID is a unique alphanumeric string used to identify the SNMP engine on the remote device which receives traps and informs from the switch Its length ranges from 10 to
171. y conserving bandwidth and improve security by limiting traffic to specific domains vlan database Description The vlan database command is used to access VLAN Configuration Mode for creating deleting 802 1Q VLAN and other operations Syntax vlan database Command Mode Global Configuration Mode Example Access VLAN Configuration Mode TP LINK config vian database TP LINK config vlan vian Description The vlan command is used to create IEEE 802 1Q VLAN To delete the IEEE 802 1Q VLAN please use no vlan command Syntax vlan VLAN_ID_LIST no vlan VLAN_ID_LIST Parameter VLAN_ID_LIST The list of VLAN ID in the format of 2 5 7 ranging from 2 to 4094 Command Mode VLAN Configuration Mode 16 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Example Create several VLANs with the vid as 2 5 7 TP LINK config vlan database TP LINK config vlan vlan 2 5 7 interface vian Description The interface vlan command is used to access VLAN Interface Mode to configure the specified VLAN Syntax interface vlan vian id Parameter vlan id VLAN ID ranging from 1 to 4094 Command Mode Global Configuration Mode Example Configure the VLAN2 TP LINK config interface vlan 2 description Description The description command is used to assign a description string to a VLAN To clear the description please use no description command Syntax description descrip
172. y name ranging from 1 to 16 characters start date The start date of the holiday in the format of MM DD for instance 05 01 end date The end date of the holiday in the format of MM DD for instance 05 03 Command Mode Global Configuration Mode Example Define National Day configuring the start date as October 1st and the end date as October 3rd TP LINK config acl holiday NationalDay 10 01 10 03 acl create Description The acl create command is used to create ACL To delete the corresponding ACL please use no acl create command Syntax acl create id 133 TL SL3428 JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide no acl create id Parameter id ACLID ranging from 0 to 299 0 99 must be MAC ACL 100 199 must be Standard IP ACL and 200 299 must be Extend IP ACL Command Mode Global Configuration Mode Example Create a MAC ACL whose ID is 20 TP LINK config acl create 20 acl rule mac acl Description The acl rule mac acl command is used to add MAC ACL rule To delete the corresponding rule please use no acl rule mac acl command MAC ACLs analyze and process packets based on a series of match conditions which can be the source MAC addresses destination MAC addresses VLAN ID and EtherType carried in the packets Syntax acl rule mac acl acl id rule id op discard permit smac source mac smask source mac mask dmac destination mac dma

TP-Link TL-SL3428 V3 CLI Reference Guide

Contents

Download Pdf Manuals

Related Search

Related Contents